Skip to Content
Proposed Rule

Hazard Communication

Action

Proposed Rule; Request For Comments.

Summary

OSHA is proposing to modify its existing Hazard Communication Standard (HCS) to conform with the United Nations' (UN) Globally Harmonized System of Classification and Labelling of Chemicals (GHS). OSHA has made a preliminary determination that the proposed modifications will improve the quality and consistency of information provided to employers and employees regarding chemical hazards and associated protective measures. The Agency anticipates this improved information will enhance the effectiveness of the HCS in ensuring that employees are apprised of the chemical hazards to which they may be exposed, and in reducing the incidence of chemical-related occupational illnesses and injuries.

The proposed modifications to the standard include revised criteria for classification of chemical hazards; revised labeling provisions that include requirements for use of standardized signal words, pictograms, hazard statements, and precautionary statements; a specified format for safety data sheets; and related revisions to definitions of terms used in the standard, requirements for employee training on labels and safety data sheets. OSHA is also proposing to modify provisions of a number of other standards, including standards for flammable and combustible liquids, process safety management, and most substance-specific health standards, to ensure consistency with the modified HCS requirements.

Unified Agenda

Hazard Communication

9 actions from September 12th, 2006 to February 2012

  • September 12th, 2006
  • November 13th, 2006
    • ANPRM Comment Period End
  • November 19th, 2007
    • Complete Peer Review of Economic Analysis
  • September 30th, 2009
  • December 29th, 2009
    • NPRM Comment Period End
  • March 2nd, 2010
    • Hearing
  • March 31st, 2010
    • Hearing
  • June 1st, 2010
    • Post Hearing Comment Period End
  • February 2012
    • Final Action
 

Table of Contents Back to Top

Tables Back to Top

DATES: Back to Top

Written comments. Written comments, including comments on the information collection determination described in Section VIII of the preamble (OMB Review under the Paperwork Reduction Act of 1995), must be submitted by the following dates:

Hard copy: Comments must be submitted (postmarked or sent) by December 29, 2009.

Facsimile and electronic transmissions: Comments must be sent by December 29, 2009.

Informal public hearings. The Agency will schedule an informal public hearing on the proposed rule. The location and date of the hearing, procedures for interested parties to notify the Agency of their intention to participate, and procedures for participants to submit their testimony and documentary evidence will be announced in the Federal Register.

ADDRESSES: Back to Top

Written comments. You may submit comments by any of the following methods:

Electronically: You may submit comments electronically at http://www.regulations.gov, which is the Federal e-Rulemaking Portal. Follow the instructions on-line for making electronic submissions.

Fax: If your submissions, including attachments, are not longer than 10 pages, you may fax them to the OSHA Docket Office at (202) 693-1648.

Mail, hand delivery, express mail, messenger or courier service: You must submit three copies of your comments to the OSHA Docket Office, Docket No. OSHA-H022K-2006-0062, U.S. Department of Labor, Room N-2625, 200 Constitution Avenue, NW., Washington, DC 20210. Deliveries (hand, express mail, messenger and courier service) are accepted during the Department of Labor's and Docket Office's normal business hours, 8:15 a.m.-4:45 p.m., E.T.

Instructions: All submissions must include the Agency name and the docket number for this rulemaking (Docket No. OSHA-H022K-2006-0062). All comments, including any personal information you provide, are placed in the public docket without change and may be made available online at http://www.regulations.gov. Therefore, OSHA cautions you about submitting personal information such as social security numbers and birthdates.

Docket: To read or download comments submitted in response to this Federal Register notice, go to Docket No. OSHA-H022K-2006-0062 at http://www.regulations.gov or to the OSHA Docket Office at the address above. All comments are listed in the http://www.regulations.gov index; however, some information (e.g., copyrighted material) is not publicly available to read or download through that Web page. All comments, including copyrighted material, are available for inspection and copying at the OSHA Docket Office.

Electronic copies of this Federal Register document are available at http://regulations.gov. Copies also are available from the OSHA Office of Publications, Room N-3101, U.S. Department of Labor, 200 Constitution Avenue, NW., Washington, DC 20210; telephone (202) 693-1888. This document, as well as news releases and other relevant information, are also available at OSHA's Web page at http://www.osha.gov.

FOR FURTHER INFORMATION CONTACT: Back to Top

For general information and press inquiries, contact Jennifer Ashley, Office of Communications, Room N-3647, OSHA, U.S. Department of Labor, 200 Constitution Avenue, NW., Washington, DC 20210; telephone (202) 693-1999. For technical information, contact Maureen O'Donnell, Directorate of Standards and Guidance, Room N-3718, OSHA, U.S. Department of Labor, 200 Constitution Avenue, NW., Washington, DC 20210; telephone (202) 693-1950.

SUPPLEMENTARY INFORMATION: Back to Top

I. Introduction Back to Top

The preamble to the proposal to modify the Hazard Communication Standard includes a review of the events leading to the proposal, a discussion of the reasons why OSHA believes these modifications are necessary, the preliminary economic and regulatory flexibility analysis for the proposal, and an explanation of the specific provisions set forth in the proposed standard. The discussion follows this outline:

I. Introduction

II. Issues

III. Events Leading to the Proposed Modifications to the Hazard Communication Standard

IV. Overview and Purpose of the Proposed Modifications to the Hazard Communication Standard

V. Need and Support for the Proposed Modifications to the Hazard Communication Standard

VI. Pertinent Legal Authority

VII. Preliminary Economic Analysis and Initial Regulatory Flexibility Analysis

VIII. OMB Review Under the Paperwork Reduction Act of 1995

IX. Federalism

X. State Plans

XI. Unfunded Mandates

XII. Protecting Children From Environmental Health and Safety Risks

XIII. Environmental Impacts

XIV. Public Participation

XV. Summary and Explanation of the Proposed Modifications to the Hazard Communication Standard

(a) Purpose

(b) Scope

(c) Definitions

(d) Hazard Classification

(e) Written Hazard Communication Program

(f) Labels and Other Forms of Warning

(g) Safety Data Sheets

(h) Employee Information and Training

(i) Trade Secrets

(j) Effective Dates

(k) Other Standards Affected

(l) Appendices

XVI. References

XVII. Authority and Signature

XVIII. Proposed Amendments

In the preamble, OSHA references a number of supporting materials. References to these materials are given as “Document ID#” followed by the last four digits of the document number. The referenced materials are posted in Docket No. OSHA-H022K-2006-0062 (which is available at http://www.regulations.osha.gov). The documents are also available at the OSHA Docket Office (see ADDRESSES section above). For further information about accessing documents referenced in this Federal Register notice, see Section XIV (Public Participation—Notice of Hearing).

II. Issues Back to Top

OSHA requests comment on all relevant issues, including economic impact and feasibility, environmental impact, effects on small entities, proposed revisions to the HCS, and subsequent modifications to other standards. OSHA has received many comments on the issues raised in the Advance Notice of Proposed Rulemaking (ANPR) (71 FR 53617, September 12, 2006), and the Agency has considered those comments in the development of this proposal. This section identifies issues on which the Agency seeks additional information and comment to supplement that received in response to the ANPR, as well as new topics related to this proposal. While new comments are welcome, OSHA requests that comments submitted in response to the ANPR not be resubmitted as they are retained in the rulemaking record and reconsidered throughout the process.

OSHA is including these issues at the beginning of the document to assist readers as they consider the comments they plan to submit. However, to fully understand the questions and provide substantive input in response to them, the parts of the preamble that address these issues in detail should be read and reviewed. These include Section VII, which addresses the impacts of the NPRM, and thus provides the background related questions 2 through 5. Section XV provides the Summary and Explanation of the proposed regulatory text, and Section XVII is the text itself. These are key to understanding questions 6 through 26. It should be noted that the Federal Register's required format for a modification of an existing standard does not allow the Agency to provide the full text of the rule, i.e., the regulatory text in this document only addresses those paragraphs that OSHA is proposing to change. Therefore, the Agency is putting a marked up version of the text of the current rule on its web page to help readers understand the proposed changes in context. The marked up text will be found on www.osha.gov under Hazard Communication in the subject index.

OSHA requests that comments be organized, to the extent possible, around the following issues and numbered questions. Submitting comments in an organized manner and with clear reference to the issue raised will enable all participants to easily see what issues the commenter addressed and how they were addressed. This is particularly important in a rulemaking such as GHS which affects many diverse industries. Many commenters, especially small businesses, are likely to confine their interest (and comment) to the issues that affect them, and they will benefit from being able to quickly identify comment on their issues in others' submissions. Of course, OSHA also welcomes relevant comments concerning the proposal that fall outside the issue questions raised in this section. However, the Agency is particularly interested in receiving public responses, supported by evidence and reasons, to the following questions:

Need and Support for the Standard

1. OSHA has made a preliminary determination that the proposed modifications to the HCS would increase the quality and consistency of information provided to employers and employees. Specifically, OSHA believes that standardized label elements would be more effective in communicating hazard information; standardized headings and a consistent order of information would improve the utility of SDSs; and training would support and enhance the effectiveness of the new label and SDS requirements. Is this assessment correct? OSHA requests information that reflects on the effectiveness of the proposed modifications to the HCS in protecting employees from chemical hazards in the workplace.

Economic Impacts and Economic Feasibility

2. The preliminary economic analysis in Section VII raises a variety of specific questions and issues with respect to the preliminary economic analysis. OSHA would appreciate it if you could place answers to these issues as heading 2 in your comments and further organize comments on the preliminary economic analysis (PEA) as follows:

a. Industrial profiles. This covers issues concerning how many employees, establishments and products would be affected by the proposed standard. OSHA welcomes comments on all aspects of the industrial profile and is particularly interested in comments on the number of affected employees, and the number of SDSs that would need revision, by industry.

b. Issues with respect to estimated benefits of the proposed standard. OSHA considers three kinds of benefits in this preliminary analysis: Benefits associated with preventing injuries, illnesses, and fatalities through clearer and more accessible information; benefits associated with reducing the time that safety and health managers and logistics and emergency response personnel spend on hazardous chemicals through clearer and easier-to-find information; and benefits associated with reducing the time needed to develop and review SDSs because of international harmonization. OSHA is particularly interested in comments on the scope of these benefits; the extent to which they are already being achieved by existing practices; and the extent to which they depend on other countries following the harmonization effort.

c. Issues with respect to the costs and range of costs of the proposed standard. OSHA preliminarily estimated the principal costs of the standard to chemical producers for reclassification of chemicals; remaking SDS's; and redoing labels; and to chemical users for familiarization and program changes for managers and for training exposed employees. OSHA welcomes comments on all aspects of the costs, and is particularly interested in comments on the extent to which chemical producers may have already met some of the requirements of the standard and the time and professional skills needed for the activities the standard would require.

d. Issues with respect to economic impacts and feasibility of the proposed standard, including the sensitivity of OSHA's economic feasibility determination with respect to various assumptions. OSHA welcomes comments on all aspects of the economic impact and economic feasibility analyses.

e. All other issues with respect to the PEA.

Effects on Small Entities

3. OSHA has certified that the proposed standard will not have a significant impact on a substantial number of small entities. Nevertheless, because of the number of small entities affected, OSHA has prepared a voluntary initial regulatory flexibility analysis, the results of which are described in Section VII of the proposed rule. Do you consider the estimated costs and impacts on small entities presented there to be reasonable? Why or why not?

4. Are there alternatives to the rule as a whole or specific requirements of the rule that reduce impacts on small entities while still protecting the health of employees and meeting the broad goal of a globally harmonized system?

Environmental Impacts

5. OSHA has preliminarily determined that the proposed standard will not have any adverse effects on the environment, and may have positive effects on the environment. OSHA welcomes comments on this determination.

Hazard Classification

6. OSHA is proposing to adopt all of the physical and health hazard classes in the GHS. Among the physical and health hazard classes, OSHA is proposing to include all hazard categories in the GHS except Acute Toxicity Category 5 for oral, dermal, or inhalation exposures; Skin Corrosion/Irritation Category 3; and Aspiration Hazard Category 2. If you believe that the exclusion of these hazard categories is not consistent with the scope and/or level of protection provided by the current HCS, please describe any recommended changes to this proposal and the reasons you think these changes are necessary.

7. OSHA has proposed a definition for unclassified hazards be added to the HCS to ensure that all hazards currently covered by the HCS—or new hazards that are identified in the future—are included in the scope of the revised standard until such time as specific criteria for the effect are added to the GHS and subsequently adopted by OSHA. Will this approach provide sufficient interim coverage for hazards such as combustible dust? Are there other hazards for which criteria should be developed and added to the GHS? Please provide information regarding these hazards, and the information available to characterize them.

8. OSHA believes it may be more appropriate to add specific coverage for simple asphyxiants to the standard in the final rule to ensure everyone properly addresses their coverage rather than addressing them under the unclassified hazard definition. This effect is simple and straightforward, and could be addressed in a definition that does not involve extensive criteria. OSHA is requesting comment on this approach. A possible definition would be as follows:

“Simple asphyxiants” are substances that displace oxygen in the ambient atmosphere, and can thus cause oxygen deprivation in exposed workers that leads to unconsciousness and death. They are of particular concern in confined spaces. Examples of asphyxiants include: nitrogen, helium, argon, propane, neon, carbon dioxide, and methane.

OSHA would also like to solicit comments on specific label elements for simple asphyxiants. No symbol would be required, but the signal word “warning” would be used, with the hazard statement “may be harmful if inhaled”. In addition, a precautionary statement such as the following would be required: May displace oxygen in breathing air and lead to suffocation and death, particularly in confined spaces.

All other requirements of the standard that apply to hazardous chemicals would also apply to chemicals that meet this definition. These substances would generally be covered already under the proposed rule as compressed gases, and may also pose other effects such as flammability that would have to be addressed as well. They are also already covered under the existing HCS. Is the definition suggested by OSHA sufficient to cover this effect? Do you have suggestions for modifying this definition? Are the label elements suggested appropriate?

9. In order to help to ensure that health hazard determinations are properly conducted under a performance-oriented approach, the HCS includes a “floor” of chemicals that are to be considered hazardous based on several cited reference lists. In addition, the existence of one toxicological study indicating a possible adverse effect is considered sufficient for a finding of hazard for any health effect. Under the GHS, there is no floor of chemicals cited, nor is there an across-the-board provision such as the one-study criterion. Instead, specific, detailed criteria are provided for each type of health hazard to guide the evaluation of relevant data and subsequent classification of the chemical. The proposed modifications to the HCS would align the standard to the GHS approach, and thus do not include the floor of chemicals nor the universal one-study rule. Would the proposed detailed criteria provide sufficient guidance for a thorough hazard evaluation?

10. OSHA has edited the chapters in the GHS for classification of physical and health hazards to remove material not directly related to classification and to otherwise streamline the text. OSHA anticipates providing the decision logics separately to serve as guidance, but has not included them in the regulatory text. Are there any additions, subtractions, or clarifications of the classification criteria from the GHS that OSHA needs to consider?

11. Certain physical hazard classification criteria (i.e., for self-reactive chemicals, organic peroxides, self-heating chemicals, explosives) either directly reference packaging or quantity, or rely on test methods that reference packaging or quantity. The criteria were developed for transport concerns. Clearly, quantity and packaging can greatly affect safe transport of chemicals that pose hazards such as those listed above. However, OSHA seeks comments on whether the criteria as stated in the GHS are appropriate for the workplace. Does use of these criteria present any obstacles to classification or create any difficulties for suppliers or users of chemicals? Describe any difficulties these criteria may present and any suggestions for addressing these issues, particularly recommendations that would be consistent with the GHS and maintain the GHS level of safety for these chemicals.

12. The GHS gives countries guidance on a cut-off or concentration limit for chemical mixtures containing target organ toxicity hazards. In Appendix A, Section A.8.3, OSHA is proposing to make the suggested 20% concentration limit mandatory so that label preparers are clear on what needs to be done. Please comment on whether this mandatory concentration limit is appropriate. If you have an alternative, please provide it along with the rationale.

Labels

13. The proposal would require pictograms to have a red frame. As discussed in Section V, OSHA believes that use of the color red will make warnings more noticeable and will aid in communicating the presence of a hazard. However, the GHS gives competent authorities such as OSHA the discretion to allow use of a black frame when the pictogram appears on a label for a package which will not be exported. For packages that will not be exported, should the modified standard allow black frames on pictograms, or should the pictogram frame be required to be presented in red?

14. In addition to the pictograms, signal word and hazard statements, GHS labels must include precautionary statements. OSHA is proposing to require the text in the precautionary statements in the GHS to be on HCS labels. As discussed in Section XV Summary and Explanation of the Proposed Standard, these statements are codified under the GHS, meaning that numbers have been assigned to them. In addition, the appropriate statements to use for each hazard class and category have been indicated in the GHS annexes. This means that label preparers will know exactly what precautionary statements to apply once they complete their hazard classification, and chemical users will see consistent language on labels to indicate the necessary precautionary measures. However, the statements are not yet considered to be part of the harmonized text like hazard statements are; rather they are included in the GHS as an suggested language. OSHA expects that other countries may adopt the codified precautionary statements when they put GHS in place. For example the EU has required that labels use the GHS codified precautionary statement text in adapting the GHS. Since OSHA did not previously require the use of precautionary statements, and had no such recommended statements to provide, the Agency is proposing to use those currently in the GHS as the mandatory requirements with the option of consolidating statements where appropriate (See Appendix C). OSHA anticipates this approach will provide the maximum benefit. OSHA is also seeking comment on whether any of these statements should be modified or if other precautionary statements should be included.

In addition, as discussed in Section IV, OSHA has presented other alternatives with regards to precautionary statements, and OSHA is soliciting comment on these options as well. Specifically, OSHA is seeking feedback on whether the Agency should include the GHS precautionary statements as nonbinding examples, through a non mandatory appendix or guidance, rather than as required statements, or whether OSHA should allow label preparers to develop their own precautionary statements rather than specifying the text to be used.

15. OSHA has not proposed to require the exploding bomb pictogram or specific precautionary statements for Division 1.4S ammunition and ammunition components because the specified GHS label elements may not accurately reflect the hazards of these materials. Is this sufficiently protective? Are any adjustments to the label elements for Division 1.4S ammunition and ammunition components necessary? Describe any requested changes and explain why such revisions are necessary.

16. In the current HCS, OSHA has a provision that requires labels to be updated within three months of obtaining new and significant information about the hazards. The Agency has not been enforcing this provision for many years, and there has been an administrative stay on enforcement. OSHA is including the provision in this proposal, and inviting comment on it with the intention of including it in the final rule and lifting the stay. Is three months the appropriate time interval for updating? Are there any practical accommodations that need to accompany this limit (for example, related to stockpiles of chemicals)? Provide any alternatives you consider appropriate, as well as documentation to support them.

Safety Data Sheets (SDSs)

17. As discussed in Section XV, the Agency is proposing to require that OSHA permissible exposure limits (PELs) be included on the SDS, as well as any other exposure limit used or recommended by the chemical manufacturer, importer, or employer preparing the safety data sheet. OSHA welcomes comments on this approach, along with an explanation of the basis for your position.

18. OSHA is proposing that Section 15 of the SDS be non-mandatory. As indicated in Appendix D, Section 15 addresses regulatory information concerning the chemical. OSHA is considering requiring the substance specific standards be referenced in this section, which would make Section 15 mandatory. Would employers and employees benefit from having this information in this section of the SDS?

Other Standards Affected

19. OSHA is proposing to align the definitions of the physical hazards to the requirements of the GHS categories in safety standards for general industry, construction, and maritime standards, which either directly reference the HCS or provide information pertinent to the Safety Data Sheets (SDSs). In most cases OSHA has modified the standards to maintain scope and protection. However, the changes in definitions for flammable liquids Category 1 and 2 and flammable aerosols appear to be more than simply rounding to the nearest significant number.

Flammable liquids Category 1 and 2: The boiling point cut-off for Category 1 is reduced from 100 deg F (37.8 deg C) or less to 95 deg F (35 deg C) or less, which could shift some liquids from Category 1 to Category 2.

Flammable aerosols: OSHA is proposing to adopt the GHS method to determine flammability rather than the method defined by the Consumer Product Safety Commission (CPSC).

OSHA's decision to change these definitions to be consistent with the GHS is based not only upon harmonizing its standards with those of other countries that have adopted or may adopt the GHS, but OSHA is also concerned with making its standards internally consistent. OSHA believes the methods used to classify these physical hazards are similar enough so that substances that are currently regulated by OSHA would continue to be regulated and that few, if any, changes would result in a shift in regulatory coverage. Would the proposed changes have any impact on your operations? If so, describe the anticipated effects.

20. OSHA is proposing to eliminate the term “combustible liquid” in 29 CFR 1910.106. 1910.107, 1910.123, 1910.124, 1910.125, and 1926.155 for liquids with a flashpoint above 100 °F. To reflect consistency with the revised HCS where appropriate, OSHA is proposing to add the specific flashpoint criteria. This will maintain equivalent protection. Are there other standards that OSHA should update with the new terminology?

21. OSHA is proposing to modify the language required on signs in substance-specific health standards. The Agency developed the proposed language to reflect the terminology of the revised HCS while, at the same time, providing adequate warning through language that is consistent with the current sign requirements for these chemicals. An added benefit is the hazard warnings on signs specified for these standards will now be consistent throughout OSHA standards. For example, all carcinogens will now bear the hazard statement “MAY CAUSE CANCER”. OSHA believes that providing language that is consistent on both signs and labels will improve comprehension for employees. Does the proposed language on signs accurately convey the hazards?

22. OSHA is proposing to revise the substance-specific health standards' provisions on labeling for producers and importers of chemicals and substances. Currently in the substance-specific standards OSHA requires specific language on labels for certain chemicals. OSHA is proposing to change these labeling requirements by referring those responsible for labeling to the modified HCS and including in each substance- specific standard a list of health effects that must be considered for hazard classification. The modified HCS will dictate the specific language (i.e., signal word, hazard statement(s), and precautionary statement(s)) that is required on labels through the classification process. However, OSHA is proposing to maintain specific language for labels on contaminated clothing and waste/debris containers to ensure adequate hazard communication for the downstream recipients. How would the removal of required language for labels from substance-specific standards affect your work place? Are there hazard warnings that will be lost that do not have an equivalent hazard or precautionary statement? Are there alternatives to OSHA's approach for the substance-specific standards that will assure information is disseminated in a manner that is consistent with the modified HCS labeling requirements?

23. In determining the health hazards that need to be considered by manufacturers, importers and distributors when classifying chemicals regulated by the substance-specific standards, OSHA is proposing to primarily rely on the determinations made by the Agency in each rulemaking, the NIOSH Pocket Guide to Chemical Hazards (2005) and the International Chemical Safety Cards, and use as a secondary source the health effects identified by the European Commission (2007). OSHA is proposing to include a health hazard only if it is identified as such by two or more of these organizations. Are there other sources of information that OSHA should consult?

24. As detailed in the Summary and Explanation section of this document, OSHA is not proposing in this rulemaking to update the electrical standards (general industry 1910 subpart S and construction 1926 subpart K) or Explosives and blasting agents (general industry 1910.109 and construction 1926.914). These subparts are “self-contained” in that they do not rely on other OSHA standards for regulatory scope or definitions, but reference external organizations (such as the National Fire Protection Association [NFPA]). OSHA believes that these standards could be updated when the referenced external organizations adopt applicable GHS elements. If OSHA were to change these standards to comply with the GHS, how would this impact your operations?

Effective Dates

25. OSHA has proposed to require that employers train employees regarding the new labels and safety data sheets within two years after publication of the final rule to ensure they are familiar with the new approach when they begin to see new labels and SDSs in their workplaces. Is the proposed time appropriate?

26. OSHA has proposed that chemical manufacturers, importers, distributors, and employers be required to comply with all provisions of the modified final rule within three years after its publication. Does this allow adequate time to review hazard classifications and amend them as necessary, and to revise labels and safety data sheets to reflect the new requirements? Would a shorter time frame be sufficient?

27. Are there any other factors that should be considered in establishing the phase-in period?

Compliance Assistance and Outreach

28. OSHA received many comments in response to the questions in the ANPR regarding compliance assistance and outreach and is seeking additional comment in this proposal. However, comments already submitted need not be resubmitted. Please refer to the discussion in Section XV. Specifically, OSHA is interested in your responses to the following: What types of materials or products would best assist employers in understanding and complying with the modified HCS? OSHA seeks input to identify the tools that would be most useful to employers and employees, the subjects of greatest interest (e.g., classification criteria, labels, safety data sheets), and the best means of distributing these materials.

29. OSHA received a number of comments that suggested that a data base of chemical classifications should be developed and maintained to assist chemical manufacturers and importers in performing hazard classifications. This approach has been adopted in some other countries. Would such a data base be helpful? Who would be responsible for doing the classifications and maintaining them? How would the data base be kept aligned with other countries' classifications?

Alternative Approaches

30. OSHA has described alternatives to the scope and application of the proposed rule in the preamble, Section IV. These include consideration of allowing voluntary implementation of the GHS; exemptions based on size of the business; adopting some components of the GHS but not others; and not adopting all of the required label elements. The Agency requests comments on these alternatives, with data to support the views expressed. Suggestions and support for other alternatives are requested as well.

III. Events Leading to the Proposed Modifications to the Hazard Communication Standard Back to Top

OSHA's Hazard Communication Standard (HCS) (29 CFR 1910.1200; 1915.1200; 1917.28; 1918.90; and 1926.59) was first issued in 1983 and covered the manufacturing sector of industry (48 FR 53280, November 25, 1983). In 1987, the Agency expanded the scope of coverage to all industries where employees are potentially exposed to hazardous chemicals (52 FR 31852, August 24, 1987). Although full implementation in the non-manufacturing sector was delayed by various court and administrative actions, the rule has been fully enforced in all industries covered by OSHA since March 17, 1989 (54 FR 6886, February 15, 1989). In 1994, OSHA made a number of minor changes and technical amendments to the HCS to help ensure full compliance and achieve better protection of employees (59 FR 6126, February 9, 1994). The development of the HCS is discussed in detail in the preambles to the original and revised final rules (see 48 FR 53280-53281; 52 FR 31852-31854; and 59 FR 6127-6131). This discussion will focus on the sequence of events leading to the development of the Globally Harmonized System of Classification and Labelling of Chemicals (GHS) and the modifications to the HCS included in this proposed rule.

The HCS requires chemical manufacturers and importers to evaluate the chemicals they produce or import to determine if they are hazardous. The rule provides definitions of health and physical hazards to use as the criteria for determining hazards in the evaluation process. Information about hazards and protective measures is then required to be conveyed to downstream employers and employees through labels on containers and safety data sheets. All employers with hazardous chemicals in their workplaces are required to have a hazard communication program, including container labels, safety data sheets, and employee training. (Note: The HCS uses the term “material safety data sheet” or “MSDS”, while the GHS uses “safety data sheet” or “SDS”. For convenience and for consistency with the GHS, safety data sheet or SDS is being used throughout this document and that term would replace MSDS in the modified HCS.)

To protect employees and members of the public who are potentially exposed to chemicals during their production, transportation, use, and disposal, a number of countries have developed laws that require information about those chemicals to be prepared and transmitted to affected parties. These laws vary with regard to the scope of chemicals covered, definitions of hazards, the specificity of requirements (e.g., specification of a format for safety data sheets), and the use of symbols and pictograms. The inconsistencies between the various laws are substantial enough that different labels and safety data sheets must often be developed for the same product when it is marketed in different nations.

Within the U.S., several regulatory authorities exercise jurisdiction over chemical hazard communication. In addition to OSHA's HCS, the Department of Transportation (DOT) regulates chemicals in transport, the Consumer Product Safety Commission (CPSC) regulates consumer products, and the Environmental Protection Agency (EPA) regulates pesticides, as well as having other authority over labeling under the Toxic Substances Control Act. Each of these regulatory authorities operates under different statutory mandates, and has adopted distinct hazard communication requirements.

Tracking the hazard communication requirements of different regulatory authorities is a burden for manufacturers, importers, distributors, and transporters engaged in commerce in the domestic arena. This burden is magnified by the need to develop multiple sets of labels and safety data sheets for each product in international trade. Small businesses may have particular difficulty in coping with the complexities and costs involved. The problems associated with differing national and international requirements were recognized and discussed when the HCS was first issued in 1983. The preamble to the final rule included a commitment by OSHA to review the standard regularly to address international harmonization of hazard communication requirements. OSHA was asked to include this commitment in recognition of an interagency trade policy that supported the U.S. pursuing international harmonization of requirements for chemical classification and labeling. The potential benefits of harmonization were noted in the preamble:

* * * [O]SHA acknowledges the long-term benefit of maximum recognition of hazard warnings, especially in the case of containers leaving the workplace which go into interstate and international commerce. The development of internationally agreed standards would make possible the broadest recognition of the identified hazards while avoiding the creation of technical barriers to trade and reducing the costs of dissemination of hazard information by elimination of duplicative requirements which could otherwise apply to a chemical in commerce. As noted previously, these regulations will be reviewed on a regular basis with regard to similar requirements which may be evolving in the United States and in foreign countries. (48 FR 53287)

OSHA has actively participated in a number of such efforts in the years since that commitment was made, including trade-related discussions on the need for harmonization with major U.S. trading partners. The Agency also issued a Request for Information (RFI) in the Federal Register in January 1990 to obtain input regarding international harmonization efforts, and on work being done at that time by the International Labor Organization (ILO) to develop a convention and recommendations on safety in the use of chemicals at work (55 FR 2166, January 22, 1990). On a closely related matter, OSHA published an RFI in May 1990 requesting comments and information on improving the effectiveness of information transmitted under the HCS (55 FR 20580, May 17, 1990). Possible development of a standardized format or order of information was raised as an issue in the RFI. Nearly 600 comments were received in response to this request. The majority of responses expressed support for a standard SDS format, and the majority of responses that expressed an opinion on the topic favored a standardized format for labels as well.

In June 1992, the United Nations Conference on Environment and Development issued a mandate (Chapter 19 of Agenda 21), supported by the U.S., calling for development of a globally harmonized chemical classification and labeling system:

A globally harmonized hazard classification and compatible labelling system, including material safety data sheets and easily understandable symbols, should be available, if feasible, by the year 2000.

This international mandate initiated a substantial effort to develop the GHS, involving numerous international organizations, many countries, and extensive stakeholder representation.

A coordinating group comprised of countries, stakeholder representatives, and international organizations was established to manage the work. This group, the Inter-Organization Programme for the Sound Management of Chemicals Coordinating Group for the Harmonization of Chemical Classification Systems, established overall policy for the work and assigned tasks to other organizations to complete. The Coordinating Group then took the work of these organizations and integrated it to form the GHS. OSHA served as chair of the Coordinating Group.

The work was divided into three main parts: Classification criteria for physical hazards; classification criteria for health and environmental hazards (including criteria for mixtures); and hazard communication elements, including requirements for labels and safety data sheets. The criteria for physical hazards were developed by a United Nations Subcommittee of Experts on the Transport of Dangerous Goods/International Labour Organization working group and were based on the already harmonized criteria for the transport sector. The criteria for classification of health and environmental hazards were developed under the auspices of the Organization for Economic Cooperation and Development. The ILO developed the hazard communication elements. OSHA participated in all of this work, and served as U.S. lead on classification of mixtures and hazard communication.

Four major existing systems served as the primary basis for development of the GHS. These systems were the requirements in the U.S. for the workplace, consumers and pesticides; the requirements of Canada for the workplace, consumers and pesticides; European Union directives for classification and labeling of substances and preparations; and the United Nations Recommendations on the Transport of Dangerous Goods. The requirements of other systems were also examined as appropriate, and taken into account as the GHS was developed. The primary approach to reconciling these systems involved identifying the relevant provisions in each system; developing background documents that compared, contrasted, and explained the rationale for the provisions; and undertaking negotiations to find an agreed approach that addressed the needs of the countries and stakeholders involved. Principles to guide the work were established, including an agreement that protections of the existing systems would not be reduced as a result of harmonization. Thus countries could be assured that the existing protections of their systems would be maintained or enhanced in the GHS.

An interagency committee under the auspices of the Department of State coordinated U.S. involvement in the development of the GHS. In addition to OSHA, DOT, CPSC, and EPA, there were a number of other agencies involved that had interests related to trade or other aspects of the GHS process. Different agencies took the lead in various parts of the discussions. Positions for the U.S. in these negotiations were coordinated through the interagency committee. Interested stakeholders were kept informed through e-mail dissemination of information, as well as periodic public meetings. In addition, the Department of State published a notice in the Federal Register that described the harmonization activities, the agencies involved, the principles of harmonization, and other information, as well as invited public comment on these issues (62 FR 15951, April 3, 1997). Stakeholders also actively participated in the discussions at the international level and were able to present their views directly in the negotiating process.

The GHS was formally adopted by the new United Nations Committee of Experts on the Transport of Dangerous Goods and the Globally Harmonized System of Classification and Labelling of Chemicals in December 2002. In 2003, the adoption was endorsed by the Economic and Social Council of the United Nations. The GHS will be updated as necessary to reflect new technology and scientific developments, or provide additional explanatory text. This proposed rule is based on Revision 3 of the GHS, published in 2009.

Countries have been encouraged to implement the GHS as soon as possible, and established a goal to have fully operational systems by 2008. This goal was adopted by countries in the Intergovernmental Forum on Chemical Safety, and was endorsed by the World Summit on Sustainable Development. The U.S. participated in these groups, and agreed to work toward achieving these goals. While much progress was made by the U.S. and other countries by the end of 2008, most are still in the process of implementing the GHS.

OSHA published an Advance Notice of Proposed Rulemaking (ANPR) on the GHS in September of 2006 (71 FR 53617, September 12, 2006). The ANPR provided information about the GHS and its potential impact on the HCS, and sought input from the public on issues related to GHS implementation. Over 100 responses were received, and the comments and information provided were taken into account in the development of the modifications to the HCS included in this proposed rule. At the same time the ANPR was published, OSHA made a document summarizing the GHS available on its Web site (http://www.osha.gov).

OSHA remains engaged in a number of activities related to the GHS. The U.S. is a member of both the United Nations Committee of Experts on the Transport of Dangerous Goods and the Globally Harmonized System of Classification and Labeling of Chemicals, as well as the Subcommittee of Experts on the Globally Harmonized System of Classification and Labeling of Chemicals. These permanent UN bodies have international responsibility for maintaining, updating as necessary, and overseeing the implementation of the GHS. OSHA and other affected Federal agencies actively participate in these UN groups. In addition, OSHA and EPA also participate in the GHS Programme Advisory Group under the United Nations Institute for Training and Research (UNITAR). UNITAR is responsible for helping countries implement the GHS, and has ongoing programs to prepare guidance documents, conduct regional workshops, and implement pilot projects in a number of nations. OSHA also continues to be involved in interagency discussions related to coordination of domestic implementation of the GHS, and in discussions related to international work to implement and maintain the GHS.

IV. Overview and Purpose of the Proposed Modifications to the Hazard Communication Standard Back to Top

The intent of the HCS is to ensure that the hazards of all chemicals are evaluated, and that information concerning chemical hazards and associated protective measures is transmitted to employers and employees. The standard achieves this goal by requiring chemical manufacturers and importers to review available scientific evidence concerning the physical and health hazards of the chemicals they produce or import to determine if they are hazardous. For every chemical found to be hazardous, the chemical manufacturer or importer must develop a container label and an SDS and provide both documents to downstream users of the chemical. All employers with employees exposed to hazardous chemicals must develop a hazard communication program, and ensure that exposed employees are provided with labels, access to SDSs, and training on the hazardous chemicals in their workplace.

The three information components in this system—labels, SDSs, and employee training—are all essential to the effective functioning of the program. Labels provide a brief, but immediate and conspicuous summary of hazard information at the site where the chemical is used. SDSs provide detailed technical information and serve as a reference source for exposed employees, industrial hygienists, safety professionals, emergency responders, health care professionals, and other interested parties. Training is designed to ensure that employees understand the chemical hazards in their workplace and are aware of protective measures to follow. Labels, SDSs, and training are complementary parts of a comprehensive hazard communication program—each element reinforces the knowledge necessary for effective protection of employees.

Information required by the HCS reduces the incidence of chemical-related illnesses and injuries by enabling employers and employees to implement protective measures in the workplace. Employers can select less hazardous chemical alternatives and ensure that appropriate engineering controls, work practices, and personal protective equipment are in place. Improved understanding of chemical hazards by supervisory personnel results in safer handling of hazardous substances, as well as proper storage and housekeeping measures.

Employees provided with information and training on chemical hazards are able to fully participate in the protective measures instituted in their workplaces. Knowledgeable employees can take the steps required to work safely with chemicals, and are able to determine what actions are necessary if an emergency occurs. Information on chronic effects of exposure to hazardous chemicals helps employees recognize signs and symptoms of chronic disease and seek early treatment. Information provided under the HCS also enables health and safety professionals to provide better services to exposed employees. Medical surveillance, exposure monitoring, and other services are enhanced by the ready availability of health and safety information.

OSHA believes that the comprehensive approach adopted in the HCS—requiring evaluation of chemicals and the transmittal of information through labels, SDSs, and training—is sound. The proposed modifications to the rule do not alter that approach. Rather, the proposed modifications to the rule are intended to improve the effectiveness of the HCS by enhancing the quality and consistency of the information provided to employers and employees. OSHA believes this can be accomplished by modifying the requirements of the standard to conform with the more specific and detailed provisions of the GHS for classification, labeling, and SDSs. OSHA's rationale for this belief is summarized below. The evidence supporting this preliminary conclusion is presented in Section V of this preamble, and the proposed revisions to the HCS are discussed in detail in Section XV.

HCS Provisions for Classification, Labeling, and SDSs

The HCS covers a broad range of health and physical hazards. The standard is performance-oriented, providing definitions of hazards and parameters for evaluating the evidence to determine whether a chemical is considered hazardous. The evaluation is based upon evidence that is currently available, and no testing of chemicals is required.

The standard covers every type of health effect that may occur, including both acute and chronic effects. Definitions of a number of adverse health effects are provided in the standard. These definitions are indicative of the wide range of coverage, but are not exclusive. Any adverse health effect that is substantiated by a study conducted according to established scientific principles, and reporting a statistically significant outcome, is sufficient for determining that a chemical is hazardous under the rule.

Most chemicals in commerce are not present in the pure state (i.e., as individual elements or compounds), but are provided as mixtures of chemicals. Evaluation of the health hazards of mixtures is based on data for the mixture as a whole when such data are available. When data on the mixture as a whole are not available, the mixture is considered to present the same health hazards as any ingredients present at a concentration of 1% or greater, or, in the case of carcinogens, concentrations of 0.1% or greater. The HCS also recognizes that risk may remain at concentrations below these cut-offs, and where there is evidence that is the case, the mixtures are considered hazardous under the standard.

The current definitions of physical hazards in the HCS were derived from other OSHA standards that address such chemicals (e.g., flammable chemicals), or from the DOT criteria for physical hazards at the time OSHA promulgated the HCS. DOT subsequently changed their criteria to be consistent with the internationally harmonized transport requirements, and the HCS criteria for classification of physical hazards are generally not consistent with current DOT requirements.

The HCS establishes requirements for minimum information that must be included on labels and SDSs, but does not provide specific language to convey the information or a format in which to provide it. When the HCS was issued in 1983, the public record strongly supported this performance-oriented approach (see 48 FR 53300-53310). Many chemical manufacturers and importers were already providing information voluntarily, and in the absence of specific requirements had developed their own formats and approaches. The record indicated that a performance-oriented approach would reduce the need for chemical manufacturers and importers to revise these existing documents to comply with the HCS, thus reducing the cost impact of the standard. In recognition of the work that had been voluntarily completed, OSHA decided to allow labels and SDSs to be presented in any format desired, as long as the minimum information requirements of the standard were met.

GHS Provisions for Classification, Labeling, and SDSs

The GHS is an internationally harmonized system for classifying chemical hazards and developing labels and safety data sheets. However, the GHS is not a model standard that can be adopted verbatim. Rather, it is a set of criteria and provisions that regulatory authorities can incorporate into existing systems, or use to develop a new system.

The GHS is designed to allow regulatory authorities to choose provisions that are appropriate to their particular sphere of regulation. This is referred to as the “building block approach.” The GHS includes all of the regulatory components, or building blocks, that might be needed for classification and labeling requirements for chemicals in the workplace, transport, pesticides, and consumer products.

Regulatory authorities such as OSHA adopt the provisions of the GHS that are appropriate for their particular regulatory sector, but do not need to adopt all of the criteria and provisions of the GHS. For example, the GHS includes criteria for classifying chemicals for aquatic toxicity. Since OSHA does not have the regulatory authority to address environmental concerns, OSHA would not adopt the GHS criteria for aquatic toxicity. The building block approach may also be applied to the criteria for defining hazards. For example, the acute toxicity criteria in the GHS are much broader than those currently found in the HCS. This is to allow consumer product authorities the ability to address the protection of children and other vulnerable populations. OSHA would not need to adopt all of the acute toxicity categories to maintain protection of employees in the workplace.

The building block approach can also be applied when a regulatory authority decides which parts of the system to adopt. For example, the GHS includes classification criteria and provisions for labels and SDSs. While OSHA is proposing to adopt all of these elements because the current HCS cover labels and SDSs, consumer product and transportation authorities are not expected to require SDSs.

Under the GHS, each hazard or endpoint (e.g., Explosives, Carcinogenicity) is considered to be a hazard class. The classes are generally sub-divided into categories of hazard. The definitions of hazards are more specific and detailed than those currently in the HCS. For example, under the HCS, a chemical is either an explosive or it is not. Under the GHS, there are seven categories of explosives, and assignment to these categories is based on the classification criteria provided.

The GHS generally applies a tiered approach to evaluation of mixtures. The first step is consideration of data on the mixture as a whole. The second step allows the use of “bridging principles” to estimate the hazards of the mixture based on information about its components. The third step of the tiered approach involves use of cut-off values based on the composition of the mixture, or for acute toxicity, a formula which is used for classification. The approach is generally consistent with the current requirements of the HCS, but provides more detail and specification and allows for extrapolation of data available on the components of a mixture to a greaterextent—particularly for acute effects.

Hazard communication requirements under the GHS are directly linked to the hazard classification. For each class and category of hazard, a harmonized signal word (e.g., Danger), pictogram (e.g., skull and crossbones), and hazard statement (e.g., Fatal if Swallowed) are specified. These specified elements are referred to as the core information for a chemical. Thus, once a chemical is classified, the GHS provides the specific core information to convey to users of that chemical. The core information allocated to each category generally reflects the degree of severity of the hazard. Precautionary statements are also required on GHS labels. The GHS provides example precautionary statements, but they are not yet considered formally harmonized. In other words, it would be possible for regulatory authorities to use different language for the precautionary statements. However, it appears likely that the language in the examples will become the harmonized text of the GHS on precautionary statements in the near future. The most recent revision to the GHS has codified these statements (i.e., assigned numbers to them) as well as aligned them with the hazard classes and categories. Codification allows reference to them in a shorthand form, and makes it easier for authorities using them in regulatory text to organize them. In addition, there are provisions to allow supplementary information so that chemical manufacturers can provide data in addition to the specified core information.

The GHS establishes a standardized 16-section format for SDSs to provide a consistent sequence for presentation of information to SDS users. Items of primary interest to exposed employees and emergency responders are presented at the beginning of the document, while more technical information is presented later. Headings for the sections (e.g., First Aid Measures, Handling and Storage) are standardized to facilitate locating information of interest. The harmonized data sheets are consistent with the order of information included in the voluntary industry consensus standard for safety data sheets (ANSI Z400.1).

Advantages of the Proposed Modifications to the Standard

OSHA believes that the detailed and specific classification requirements of the GHS would result in better, more consistent information being provided to employers and employees. Classification under the revised criteria would not only indicate the type of hazard, but would generally give an indication of the degree of severity of the hazard as well. This information would be helpful to both employers and employees in understanding chemical hazards and identifying and implementing protective measures. The detailed criteria for classification are also expected to result in greater accuracy in hazard classification and more consistency among classifiers. By following the detailed criteria, classifiers are less likely to reach different interpretations of the same data.

OSHA also believes that standardized presentation of information on labels and safety data sheets would improve the comprehensibility of chemical hazard information. Employers and employees would be given the same core information on a chemical regardless of the supplier. Use of standardized pictograms would complement and reinforce the information provided through signal words and hazard statements. Pictograms are also anticipated to improve communication for those who are not functionally literate, or who are not literate in the language used on the label. The standardized format for SDSs is expected to make the information easier for users to find, with the information employees and emergency responders need most appearing in the beginning of the document for easy identification and reference.

Standardized requirements for labels and SDSs are also expected to increase the accuracy of chemical hazard information. With consistent presentation of information, the task of reviewing SDSs and labels to assure accuracy would be simplified. Individuals preparing and reviewing these documents should find it easier to identify any missing elements, and OSHA enforcement personnel should be able to more efficiently examine SDSs and labels when conducting inspections.

Another advantage that will result from adopting a system that has harmonized hazard statements in it relates to the use of “control banding,” a guidance approach to recommending control measures for chemical exposures. The approach uses information that is readily available to small and medium-sized employers with chemicals in their workplaces to provide them with workplace-specific control recommendations. Basically, the system uses such information to estimate the degree of severity of the hazard and the amount of chemical present, and relates that to the degree of control needed. The control banding approach relies on harmonized hazard statements to allow the system to estimate the degree of severity of the hazard. Initially based on the European hazard classification system, it has now been converted to the GHS phrases. The use of control banding to provide guidance for chemical safety and health approaches in U.S. workplaces cannot be accomplished until harmonized hazard statements are readily available. Adoption of the GHS and its phrases would open up the possibility that control banding guidance can be used in the U.S. to help small and medium-sized employers select and implement appropriate control measures. For more information on control banding, please see http://www.cdc.gov/niosh/topics/ctrlbanding/.

OSHA is proposing modifications to the HCS that are necessary for consistency with the GHS. The GHS does not include requirements for a written hazard communication program or for employee training. OSHA is not proposing any substantive changes to the requirements for a written hazard communication program. However, OSHA believes that additional training would be necessary to ensure that employees understand some elements of the new system. In particular, some training and familiarization would be needed for pictograms to be effective. The Agency is therefore proposing modified training requirements to address the new label elements and SDS format that would be required under the revised standard.

The GHS leaves certain matters to the competent authority (i.e., the regulatory authority with jurisdiction over that sector) to determine. OSHA would maintain its current approaches in these situations. For example, the scope and application provisions in the HCS address the interface of the OSHA requirements with requirements of other agencies. These scope provisions would remain unchanged under the proposed rule.

The proposed modifications to the HCS primarily affect manufacturers and importers of hazardous chemicals. Chemical manufacturers and importers would be required to re-evaluate chemicals according to the new criteria in order to ensure they are classified appropriately. For health hazards, this will necessitate placing the chemical in the appropriate hazard category as well as the hazard class. For physical hazards, however, the new criteria are generally consistent with current DOT requirements for transport. Therefore, if the chemicals are transported (i.e., they are not produced and used in the same workplace), this classification should already be done for physical hazards for purposes of complying with DOT's transport requirements. This should minimize the additional work required for classification of physical hazards. Preparation and distribution of modified labels and safety data sheets by chemical manufacturers and importers would also be required. Those chemical manufacturers and importers already following the ANSI Z400.1 standard for safety data sheets should already have the appropriate format, and would only be required to make some small modifications to the content of the sheets to be in compliance.

Compliance requirements for chemical users would be limited. Workplaces where chemicals are used would need to integrate the new approach into their hazard communication program, assuring that employees understand the pictograms and other information provided on labels and SDSs. Employers who use chemicals, and exposed employees, would benefit from receiving labels and safety data sheets presented in a consistent format. The information should be easier to find and comprehend, allowing it to be used more effectively for the protection of employees.

Changing the HCS to make it conform to the GHS will also make it necessary to modify a number of other OSHA standards. Modifications are proposed to the standards for Flammable and Combustible Liquids in general industry (29 CFR 1910.106) and construction (29 CFR 1926.152) to align the requirements of the standards with the GHS hazard categories for flammable liquids. A modification to the Process Safety Management standard (29 CFR 1910.119) is proposed to ensure that the scope of the standard is not changed by the proposed modifications to the HCS. In addition, modifications to most of OSHA's substance-specific health standards are proposed to ensure that requirements for signs and labels are consistent with the modified HCS.

OSHA's preliminary determination to modify the HCS is based on its assessment of the potential to improve employee safety and health by adopting the GHS approach to hazard communication. However, GHS implementation is also expected to accomplish a number of other objectives, and produce additional benefits. By providing an internationally comprehensible system for hazard communication, the GHS is anticipated to enhance the protection of the environment and of human health in all sectors, not only the workplace. The GHS provides a framework for developing a hazard communication system for those countries without an existing system, thus protecting employees around the world and helping to ensure that the appropriate information is received with chemicals imported into American workplaces. Implementation of the GHS is also expected to reduce the need for testing and evaluation of chemicals, since classification would be based on existing data and would only need to be performed once for each substance. In addition, implementation of the GHS is expected to facilitate international trade in chemicals, as the need to identify and comply with diverse and complex hazard communication requirements in different countries would be reduced or eliminated.

Alternative Approaches

In this section OSHA presents several alternatives to the proposed GHS modification to the HCS to respond to concerns raised by commenters through the ANPR. OSHA provides the following discussion of these alternatives and their potential impacts and requests comments regarding their relative costs, benefits, feasibility, impact on small businesses, impact on worker safety and health, and any other issues on which commenters may wish to provide feedback.

This rulemaking seeks to improve employee protections by adopting an internationally harmonized approach to hazard communication issues. While the current HCS provides protections for exposed workers by disseminating information about chemicals in their workplaces, OSHA believes, as discussed in Section V, that the adoption of GHS strengthens and refines the system, and gives OSHA the opportunity to improve worker safety by improving hazard communications. The GHS has the same general concept of an integrated, comprehensive process of identifying and communicating hazards, but provides more extensive criteria to define the hazards in a consistent manner, as well as standardizes label elements and SDS formats to help to ensure that the information is conveyed consistently.

Additionally, the Agency believes that adoption of the GHS as proposed will simplify implementation insofar as OSHA's preferred alternative would clearly be considered “harmonized” with other regulatory authorities in the world, and thereby acquire the full benefits of harmonization.

This is in line with the GHS, which anticipates that countries will adopt the hazard classification criteria and required label elements, as well as SDS requirements in workplaces. As stated in the introduction to the GHS (3rd revision):

1.1.3.1.3In the workplace, it is expected that all of the GHS elements will be adopted, including labels that have the harmonized core information under the GHS, and safety data sheets. It is also anticipated that this will be supplemented by employee training to help ensure effective communication.

As addressed in Section XV, many commenters supported the concept of OSHA moving forward to adopt the GHS (Document ID #s 0003, 0007, 0047, 0050, 0052, 0062, 0106, 0011, 0033, 0038, 0123, 0130, 0151, 0163, and 0171). While others objected to adoption, OSHA has identified and responded to their concerns in Section XV as well. In addition, there were several commenters who noted that small chemical manufacturers that are not in international trade of chemicals would have a large burden associated with adopting the GHS, and questionable benefits due to their lack of international trade. (Document ID # 0022). Others simply noted that they believed there would be high costs and limited benefits for such employers, or that it would be costly and difficult to adopt (Document ID #s 0015, 0026, 0178, and 0144). There was no discussion in any of these comments about potential alternatives.

It should be noted that it appears that all of these commenters assumed the primary benefits of adopting the GHS would be in facilitating international trade. As has been addressed in Section VII, OSHA has based the benefits of this action on improved communication to workers and has provided initial estimates of a range of benefits that would be achieved in this area; trade benefits which, while recognized, have not been quantified. Therefore, grandfathering or other exemptions related to this rule might result in workers in those facilities receiving lower benefits of increased comprehensibility relative to workers in other types and sizes of workplaces; OSHA considers this a serious concern that could potentially exclude a group of workers exposed to hazardous chemicals from the increased benefits associated with clearer and more specific classification criteria, as well as standardized label elements.

Alternatives:

In order to respond to the concerns raised in these comments, OSHA solicits comment on several options:

1. The first option is designed to facilitate voluntary adoption of GHS within the existing HCS framework. Specifically, this approach would involve recognition and adoption of the GHS, with minimal changes to the current HCS. Under this approach, entities could opt to adopt GHS or continue to follow their current practice under HCS.

Therefore, companies would decide whether they would continue complying with the existing standard, or comply with the GHS. This would reduce the costs for those companies that choose to remain in compliance with the existing HCS, and allow those companies that foresee the benefits of GHS compliance from a trade perspective to adopt its provisions. Another version of this option would be to exempt small chemical producers from complying.

2. A second option that OSHA is seeking to solicit comment on would make modifications to the current HCS in order to improve hazard communication through adoption of components of the GHS. Under this option OSHA would add requirements for standardized hazard statements, signal words, and precautionary statements being added to the current HCS, but otherwise would follow the approach outlined in Alternative 1 above.

Since the standardized labels are relatively inexpensive to implement, while reviewing classifications is more costly, this has the potential to reduce the overall cost of implementation of the revised rule.

A variation on this alternative would entail incorporation of some, but not all, of the label elements. In particular, the Agency would not adopt the precautionary statements since these are not yet considered to be “harmonized” under the GHS—they are provided for guidance and reference, but competent authorities may choose to implement other statements. The precautionary statements could be adopted later when they are harmonized under the GHS. Or, alternatively, OSHA could either allow label preparers to use whatever precautionary statements they deem appropriate or develop its own set of statements to require.

From OSHA's perspective, a key issue regarding the alternative approaches presented is that the classification criteria in the GHS are different from the hazard definitions in the current HCS. In general, as discussed in Section XV, they cover the same scope of hazard so these differences do not result in significant differences in the chemicals covered. But the GHS criteria divide most of the hazard classes into hazard categories that convey the severity of the effect, while few of the hazard classes in the current HCS take this approach. The standardized label elements are associated with these specific hazard categories, i.e., the harmonized pictograms, signal words, and hazard statements are assigned by hazard category and reflect the degree of hazard it presents to those exposed. Likewise, the precautionary statements assigned are also reflective of the degree of hazard, with responses related to these presumed hazard levels.

Additionally, with regard to the first alternative, there will be chemicals that will be classified in different hazards classes under the GHS classification scheme versus the HCS hazard determination step. In addition, these chemicals will also be assigned to hazard categories under GHS where there are none now. This is particularly true for the classification of mixtures for all hazards, except the chronic health hazards, since the hazard determination scheme in the current HCS is based solely on concentration limits and the GHS classification scheme is based on bridging principles. Under the alternatives presented workers might be given different hazard information when exposed to a chemical purchased from two different suppliers. OSHA notes that this would be similar to the situation under the current performance-oriented HCS, but this approach may forego an opportunity to make the system more consistent.

OSHA is interested in comments related to the alternatives addressing the extent to which differences in classification between the GHS and HCS might create confusion or otherwise result in problems. OSHA is further interested in comments addressing the classification of mixtures under the alternatives discussed, given the differences in classification under HCS and GHS applicable to mixtures.

Given the current variability in MSDS and labels under the performance based HCS, OSHA believes that this approach might not have a negative impact on safety and health relative to our current HCS. However, the Agency anticipates that components of the GHS would confer benefits external to producers (e.g., the benefits associated with clearer and more specific classification criteria, as well as labels or other changes that could potentially make easier for users to locate and understand the information they are seeking), adoption of this alternative could result in foregone benefits. In addition, a small number of chemicals or mixtures might be labeled differently due to differing categorization results between the existing HCS and GHS.

OSHA is generally seeking comment on the possible cost impacts associated with the alternatives on the chain of chemical suppliers. OSHA notes that large and small producers are not mutually exclusive so that a large business or distributers engaged in international trade cannot simply and straightforwardly choose to implement the GHS regardless of their suppliers. Small businesses sell to large businesses. If small businesses do not adopt the GHS, then the large businesses or the distributor would either have to generate GHS classifications for chemicals they buy from them or request that small businesses supply data and labels using GHS classifications. Likewise, chemical producers often provide their products to distributors who then sell them to customers unknown to the original producer. Thus knowing whether or not a product will wind up in international trade may be questionable in some situations. A producer may provide a substance to another company, who then formulates it into a product that is sold internationally—thus the original producer is involved in international trade without necessarily realizing it. In theses cases, costs would be incurred for the conversion to GHS. This issue was raised in comments regarding the effective dates for the rule, when many suggested it was not appropriate to differentiate dates based on the size of the business. For example, ORC Worldwide, Inc. stated (Document ID # 0123):

OSHA should consider a company's place in the manufacturing supply chain, not size, in determining how the phase-in is implemented. It would be sensible to start with producers of raw materials and basic chemicals. The technical information, classification and categorization they perform will be useful downstream for the intermediate chemical producers and specialty chemical manufacturers. Lastly, the end user will benefit from the influx of information developed by the upstream professionals.

OSHA solicits comment on whether a voluntary system, or a system based on business size, could be successfully implemented given the structure of the supply system.

OSHA seeks comment on how companies that use chemicals, but don't produce them, would be affected under an alternative approach. Rather than potentially simplifying compliance and improving comprehensibility, the user of chemicals would continue to see variation in labels on purchased chemicals. This would be further complicated by the fact that the underlying criteria for these labels may be different as well, and thus the warnings would be too. If there is no requirement for such employers to be familiar with the new system, and train their employees, then there will be new pictograms and signal words with no structure for ensuring they are understood and the appropriate precautions are implemented.

Regarding Alternative 2, under OSHA's proposed approach the label provisions are relatively cost-efficient to adopt given that the GHS assigns the various required elements by hazard class and category and once the classification or re-classification has been accomplished, the GHS provides the specific information for the label.

OSHA solicits comment on whether requiring this standardized approach to labeling under the HCS, without the infrastructure of the GHS will be burdensome for the chemical manufacturer to accomplish OSHA further solicits comment on whether confusion may result from labels that may look the same but which actually reflect different classification criteria. Under this approach, chemical producers will have to assess their current determinations and attempt to relate them to the established hazard classes and categories. Alternatively, OSHA could create a regulatory system assigning HCS categories to each GHS label elements; comments are welcomed on the impact on benefits and costs, and the feasibility of such an approach. OSHA believes it is unlikely that this component of Alternative 2 would provide significant savings over reviewing classifications for purposes of putting the chemicals into GHS classes and categories.

OSHA is concerned that chemical producers following this approach might not be able to use their labels in other countries where the GHS has been adopted. OSHA is further concerned that adopting only some elements of the GHS label may be confusing and may fail to provide useful information regarding the possible hazardous effects of exposure. Delaying adoption of the precautionary statements may also reduce the effectiveness of the labels significantly, and reduce the appropriate information on the SDSs as well. A variation on this alternative—to simply require precautionary statements, but not to specify what they are, may generate significant variation due to the performance-oriented approach that allows the label preparer to determine what they are or if they are included. One communication advantage of providing the information in the same language from label-to-label is that workers and other users can be assured that the same action is required. If you take a simple preventive measure such as “wash your hands,” but convey it in several different ways, the reader of the label will think you mean something different. This is one of the advantages of providing the text for these statements in the revised HCS. In addition, since these precautionary statements will be translated, this should make it easier for those participating in international trade to produce and use labels.

Thus, OSHA solicits comment on a range of alternative approaches to regulatory adoption of GHS and welcomes comments on these options. The costs and benefits are further addressed in Section VII.

V. Need and Support for the Proposed Modifications to the Hazard Communication Standard Back to Top

Chemical exposure can cause or contribute to many serious adverse health effects such as cancer, sterility, heart disease, lung damage, and burns. Some chemicals are also physical hazards and have the potential to cause fires, explosions, and other dangerous incidents. It is critically important that employees and employers are apprised of the hazards of chemicals that are used in the workplace, as well as associated protective measures. This knowledge is needed to understand the precautions necessary for safe handling and use, to recognize signs and symptoms of adverse health effects related to exposure when they do occur, and to identify appropriate measures to be taken in an emergency.

OSHA established the need for disclosure of chemical hazard information when the HCS was issued in 1983 (48 FR 53282-53284). This need continues to exist. The Agency estimates that 880,000 hazardous chemicals are currently used in the U.S., and over 40 million employees are now potentially exposed to hazardous chemicals in over 5 million workplaces.

Chemical exposures result in a substantial number of serious injuries and illnesses among exposed employees. The Bureau of Labor Statistics estimates that employees suffered 55,400 illnesses that could be attributed to chemical exposures in 2007, the latest year for which data are available (BLS, 2008). In that same year, 17,340 chemical-source injuries and illnesses involved days away from work (BLS, 2009).

The BLS data, however, do not indicate the full extent of the problem, particularly with regard to illnesses. As noted in the preamble to the HCS in 1983, BLS figures probably only reflect a small percentage of the incidents occurring in exposed employees (48 FR 53284). Many occupational illnesses are not reported because they are not recognized as being related to workplace exposures, are subject to long latency periods between exposure and the manifestation of disease, and other factors (e.g., Herbert and Landrigan, 2000; Leigh et al., 1997; Landrigan and Markowitz, 1989).

The HCS currently serves to ensure that information concerning chemical hazards and associated protective measures is provided to employers and employees. However, OSHA's experience, along with information acquired since the HCS was issued, indicates that modifications to the standard may be appropriate. The Agency believes that the proposed changes, based on the GHS, will substantially improve the quality and consistency of the information provided to employers and employees. OSHA further believes the proposed revisions to the HCS will enhance workplace protections, because better information will enable employers and employees to take measures that would result in a reduction in the number and severity of chemical-related injuries and illnesses.

A key foundation underlying this belief relates to the comprehensibility of information conveyed under the GHS. All hazard communication systems deal with complicated scientific information being transmitted to largely non-technical audiences. During the development of the GHS, in order to construct the most effective hazard communication system, information about and experiences with existing systems were sought to help ensure that the best approaches would be used. Ensuring the comprehensibility of the GHS was a key issue during its development. As noted in a Federal Register notice published by the U.S. Department of State (62 FR 15956, April 3, 1997): “A major concern is to ensure that the requirements of the globally harmonized system address issues related to the comprehensibility of the information conveyed.” This concern is also reflected in the principles of harmonization that were used to guide the negotiations and discussions during the development of the GHS. As described in Section 1.1.1.6(g) of the GHS, the principles included the following: “[T]he comprehension of chemical hazard information, by the target audience, e.g., workers, consumers and the general public should be addressed.”

To help in the development of the GHS, OSHA had a review of the literature conducted to identify studies on effective hazard communication, and made the review and the analysis of the studies available to other participants in the GHS process. Prepared by researchers at the University of Maryland, the document entitled “Hazard Communication: A Review of the Science Underpinning the Art of Communication for Health and Safety” (Sattler et al., 1997) has also long been available to the public on OSHA's Hazard Communication web page. More recently, OSHA conducted an updated review of the literature published since the 1997 review. This updated review examined the literature relevant to specific hazard communication provisions of the GHS (ERG, 2007).

Further work related to comprehensibility was conducted during the GHS negotiations by researchers in South Africa at the University of Cape Town—the result is an annex to the GHS related to comprehensibility testing (see GHS Annex 6, Comprehensibility Testing Methodology) (United Nations, 2009). Such testing has been conducted in some of the developing countries preparing to implement the GHS, and has provided these countries with information about which areas in the GHS will require more training in their programs to ensure people understand the information. The primary purpose of these activities was to ensure that the system developed was designed in such a way that the messages would be effectively conveyed to the target audiences, with the knowledge that the system would be implemented internationally in different cultures with varying interests and concerns.

Also among the agreed principles that were established to guide development of the GHS was that the level of protection offered by an existing hazard communication system should not be reduced. Following these principles, the best aspects of existing systems were identified and included in a single, harmonized approach to classification, labeling, and development of SDSs.

The GHS was developed by a large group of experts representing a variety of perspectives. Over 200 experts provided technical input on the project. The United Nations Sub-Committee of Experts on the GHS, the body that formally adopted the GHS and is now responsible for its maintenance, includes 32 member nations as well as 17 observer nations. Authorities from these member states are able to convey the insight and understanding acquired by regulatory authorities in different sectors, and to relate their own experiences in implementation of hazard communication requirements. In addition, over two dozen international and intergovernmental organizations, trade associations, and unions are represented, and their expertise serves to inform the member nations. The GHS consequently represents a consensus recommendation of experts with regard to best practices for effective chemical hazard communication, reflecting the collective knowledge and experience of regulatory authorities in many nations and in different regulatory sectors, as well as other organizations that have expertise in this area. A number of United States-based scientific and professional associations have endorsed adoption of the GHS. The American Chemical Society indicated its support for the GHS, stating: “The American Chemical Society (ACS) strongly supports the adoption of the GHS for hazard communication in general and specifically as outlined in the ANPR” adding that “* * * ACS anticipates that OSHA implementation of GHS in the U.S. will enhance protection of human health and the environment through warnings and precautionary language that are consistent across different products and materials as well as across all workplaces” (Document ID #0165). In comments submitted in response to the ANPR, the American Industrial Hygiene Association (AIHA) affirmed its support for modification of the HCS to adopt the GHS. AIHA maintained that standardized labels and safety data sheets will make hazard information easier to use, thereby improving protection of employees (Document ID #0034). The American Society of Safety Engineers also indicated its support for the GHS rulemaking (Document ID #0139). While acknowledging that the GHS presents a number of concerns and challenges, the Society of Toxicology has also expressed its support for the GHS, stating that “a globally harmonized system for the classification of chemicals is an important step toward creating consistent communications about the hazards of chemicals used around the world” (SOT, 2007). The American Association of Occupational Health Nurses joined these organizations in advocating adoption of the GHS, arguing that standardization of chemical hazard information is critical to protecting the safety and health of employees (Document ID #0099). The positions taken by these organizations point to wide support for the GHS among the scientific and professional communities.

In addition to the endorsement of the GHS by a group of experts with extensive knowledge and experience in chemical hazard communication and support from scientific and professional associations with expertise in this area, a substantial body of evidence indicates that the proposed modifications to the HCS will better protect employees. Specifically, this evidence supports OSHA's belief that: (1) Standardized label elements—signal words, pictograms, hazard statements and precautionary statements—would be more effective in communicating hazard information; (2) standardized headings and a consistent order of information would improve the utility of SDSs; and (3) training would support and enhance the effectiveness of the new label and SDS requirements.

This evidence was obtained from a number of sources. OSHA has commissioned several studies to examine the quality of information on SDSs (Karstadt, 1988; Kearney/Centaur 1991a, 1991b; Lexington Group, 1999); the General Accounting Office (GAO) has issued two reports based on its evaluation of certain aspects of the HCS (GAO 1991, 1992); a National Advisory Committee on Occupational Safety and Health (NACOSH) workgroup conducted a review of hazard communication and published a report of its findings (NACOSH, 1996); and a substantial amount of scientific literature relating to hazard communication has been published. As mentioned previously, OSHA commissioned a review of the literature, and a report based on that review was published in 1997 (Sattler et al., 1997). An updated review was published in 2007 (ERG, 2007). In addition, OSHA conducted a review of the requirements of the HCS and published its findings in March of 2004 (OSHA, 2004). Key findings derived from these sources are discussed below.

OSHA's rationale for adopting the GHS is tied to anticipated improvements in the quality and consistency of the information that would be provided to employers and employees. Hazard classification is the foundation for development of this improved information. Indeed, hazard classification is the procedure of identifying and evaluating available scientific evidence in order to determine if a chemical is hazardous, and the degree of hazard, pursuant to the criteria for health and physical hazards set forth in the standard. Hazard classification provides the basis for the hazard information that is provided in labels, SDSs, and employee training. As such, it is critically important that classification be performed accurately and consistently.

The GHS provides detailed scientific criteria to direct the evaluation process. The specificity and detail provided help ensure that different evaluators would reach the same conclusions when evaluating the same chemical. Moreover, the GHS refines that classification process by establishing categories of hazard within most hazard classes. These categories indicate the relative degree of hazard, and thereby provide a basis for determining precise hazard information that is tailored to the level of hazard posed by the chemical. The classification criteria established in the GHS thus provide the necessary basis for development of the specific, detailed hazard information that would enhance the protection of employees.

Labels

Labels provide a brief, conspicuous hazard summary at the work site where a chemical is used. Labels serve as an immediate visual reminder of chemical hazards, and complement the information presented in training and on SDSs.

The HCS currently requires that labels on hazardous chemical containers include the identity of the hazardous chemical; appropriate hazard warnings that convey the specific physical and health hazards, including target organ effects; and the name and address of the chemical manufacturer, importer, or other responsible party. The HCS does not specify a standard format or design elements for labels.

OSHA is proposing a requirement that labels include four new, standardized elements: a signal word; hazard statement(s); pictogram(s); and precautionary statement(s) (see Section XV for a detailed discussion of the proposed requirements). The appropriate label elements for a chemical would be determined by the hazard classification. OSHA believes that these standardized label elements would better convey critically important hazard warnings, and provide useful information regarding precautionary measures that would serve to better protect employees.

A great deal of literature has been developed that examines the effectiveness of warnings on labels. However, some important limitations must be recognized in applying this information to workplace labels for hazardous chemical products. Most studies have examined labels for prescription and non-prescription medications, alcoholic beverages, or consumer products. Relatively few studies pertain specifically to labels for hazardous chemicals in the workplace. Much of the literature is also characterized by the use of research subjects such as college students or consumers. Such subjects may not be representative of workplace populations, as these subjects may differ from typical employees in terms of product knowledge, hazard perception, perceptual abilities, and safety motivation. In addition, some studies involve non-U.S. populations that may not be representative of the U.S. workforce.

Nevertheless, the literature provides a substantial body of information applicable to workplace chemical labels. In spite of the differences in affected populations, workplace chemical labels have many characteristics that are comparable to those found in other sectors. Pharmaceutical labels, for example, are similar to chemical labels in that they often have explicit instructions for use which, if not followed, can cause adverse health effects or death. Designers of pharmaceutical labels also encounter many of the same challenges faced by those who design chemical labels, such as container space limitations and the need to convey information to low-literate or non-English literate users. In addition, some of the research is not directly related to any particular sector or type of product. Some findings related to use of color, for example, could reasonably be applied to a wide variety of label applications. Relevant finding from the literature are presented in the sections that follow.

Signal Words

A signal word is a word that typically appears near the top of a warning, sometimes in all capital letters. Common examples include DANGER, WARNING, CAUTION, and NOTICE. The signal word is generally understood to serve a dual purpose: alerting the user to a hazard and indicating a particular level of hazard. For example, users generally perceive the word DEADLY to indicate a far greater degree of hazard than a term like NOTICE.

The proposal prescribes one of two signal words for labels—DANGER or WARNING—depending on the hazard classification of the substance in question. These are the same two signal words used in the GHS. DANGER is used for the more severe hazard categories, while WARNING denotes a less serious hazard. These signal words are similar to those in other established hazard communication systems, except that some other systems have three or more tiers. For example, ANSI Z129.1 (the American National Standard for Hazardous Industrial Chemicals—Precautionary Labeling) uses DANGER, WARNING, and CAUTION, in order of descending severity (ANSI, 2006).

A number of recent studies have examined how people perceive signal words and, in particular, how they perceive signal words to be different from one another. Overall, this research supports the use of signal words in labels, demonstrating that they can attract attention and help people clearly distinguish between levels of hazard. The research also supports the decision to use only two tiers, as many recent studies have found clear differences between DANGER and WARNING but little perceived difference between WARNING and CAUTION.

Wogalter et al. investigated the influence of signal words on perceptions of hazard for consumer products (Wogalter et al., 1992). Under the pretext of a marketing research study, 90 high school and college students rated product labels on variables such as product familiarity, frequency of use, and perceived hazard. Results showed that the presence of a signal word increased perceived hazard compared to its absence. Between extreme terms (e.g., NOTE and DANGER), significant differences were noted.

Seeking to test warning signs in realistic settings, Adams et al. tested five industrial warning signs on a group of 40 blue-collar workers employed in heavy industry, as well as a group of students (Adams et al., 1998). Signs were manipulated to include four key elements (signal word, hazard statement, consequences statement, and instructions statement) or a subset of those elements. Participants were asked questions to gauge their reaction and behavioral intentions. Overall, 77 percent (66 percent of the worker group) recognized DANGER as the key word when it appeared, and more than 80 percent recognized BEWARE and CAUTION, suggesting that the signal word was generally noticed, and it was recognized as the key alerting element. DANGER was significantly more likely than other words to influence behavioral intentions.

Laughery et al. also demonstrated the usefulness of signal words. The authors tested the warnings on alcoholic beverage containers in the U.S., and found that a signal word (WARNING) was one of several factors that decreased the amount of time it took for participants to locate the warning. (Laughery et al., 1993).

Several studies have tested the arousal strength or perceived hazard of different signal words. Arousal strength is a term used to indicate the overall importance of the warning, and incorporates both the likelihood and severity of the potential threat. Silver and Wogalter tested the arousal strength of signal words on college students and found that DANGER connoted greater strength than WARNING and CAUTION (Silver and Wogalter, 1993). The results failed to show a difference between WARNING and CAUTION. Among other words tested, DEADLY was seen as having the strongest arousal connotation, and NOTE the least.

Griffith and Leonard asked 80 female undergraduates (who were unlikely to have already received industrial safety training) to rate signal words. Results included a list of terms in order of “meaningfulness,” representing conceptual “distance” from the neutral term NOTICE (Griffith and Leonard, 1997). From most to least meaningful, these terms were reported to be DANGER, URGENT, BEWARE, WARNING, STOP, CAUTION, and IMPORTANT.

Wogalter et al. asked over 100 undergraduates and community volunteers to rank signal words (Wogalter et al., 1998). DEADLY was perceived as most hazardous, followed by DANGER, WARNING, and CAUTION. All differences were statistically significant. In a follow-up experiment using labels produced in the ANSI Z535.2 (American National Standard for Environmental and Facility Safety Signs), ANSI Z535.4 (American National Standard for Product Safety Signs and Labels), and alternative formats, the authors found a similar rank order for signal words with all labeling systems. Finally, the authors tested the same terms on employees from manufacturing and assembly plants and found the same general order: DEADLY, then DANGER, then WARNING and CAUTION with no significant difference between the last two terms.

In more of a free-form experiment, Young asked 30 subjects to produce warning signs for a set of scenarios, using different sign components available on a computer screen (Young, 1998). In roughly 80 percent of the signs, the participant chose to use a signal word. DANGER, DEADLY, and LETHAL were more likely to be used for scenarios with severe hazards; CAUTION and NOTICE for non-severe scenarios. WARNING was used equally in both types of scenarios. The author suggests that these results support a two-tiered system of signal words. In a separate task, users ranked the perceived hazard of signal words, resulting in the following list from most to least severe: DEADLY, LETHAL, DANGER, WARNING, CAUTION, and NOTICE.

While these studies have focused on the relative perceptions of signal words, others have sought to evaluate how the absolute meaning of common signal words is perceived. Drake et al. asked a group of students and community volunteers to match signal words with definitions borrowed from consensus standards and other sources (Drake et al., 1998). Participants matched DANGER to a correct definition 64 percent of the time, while NOTICE was matched correctly 68 percent of the time. WARNING and CAUTION were matched correctly less than half of the time, suggesting confusion. The authors recommended using WARNING and CAUTION interchangeably. The authors also suggested that a standard set of signal words (but not synonyms) is helpful for users with limited English skills, who can be trained to recognize a few key words.

Signal word perceptions are reported to be consistent among some non-U.S. populations, as well. Hellier et al. asked 984 adults in the UK to rate DANGER, WARNING, and CAUTION on a hazard scale from 1 (low) to 10 (high) (Hellier et al., 2000a). DANGER was ranked as 8.5, WARNING was ranked as 7.8, while CAUTION was rated as 7.25. These results are consistent with the findings of studies on subjects in the U.S. In a second study published in 2000, Hellier et al. asked a mixed-age group of participants in the UK to rate the arousal strength of 84 signal words commonly used in the U.S. (Hellier et al., 2000b).The authors found that DANGER is stronger than WARNING, while WARNING and CAUTION are not significantly different from each other.

Similar results were found among workers in Zambia. Banda and Sichilongo tested GHS-style labels using four different signal words (as well as other variables) (Banda and Sichilongo, 2006). Among workers in the industrial and transport sectors, DANGER was generally perceived as the most hazardous signal word. WARNING was one of a group of terms that were largely indistinguishable from one another, but distinct from DANGER. The authors support adoption of the GHS, suggesting that having just two possible signal words will lead to “more impact and less confusion about the extent of hazard.”

In addition, comparable results were found in South Africa (London, 2003). In a large study on SDS and label comprehensibility conducted for South Africa's National Economic Development and Labour Council (NEDLAC), DANGER was generally ranked as more hazardous than WARNING by participants in the four sectors tested: industry, transport, agriculture, and consumers.

Cumulatively, these studies provide a clear indication that signal words are effective in alerting readers that a hazard exists, and in conveying the existence of a particular level of hazard. The studies have found a generally consistent hierarchy of signal words with respect to perceived hazard. DANGER and WARNING appear to connote different levels of hazard, while the perceived difference between WARNING and CAUTION is often insignificant.

Pictograms

A pictogram is a graphical composition that may include a symbol along with other graphical elements, such as a border or background color. A pictogram is a communication tool and is intended to convey specific information.

The proposed rule includes requirements for use of eight different pictograms. Each of these pictograms consists of a different symbol in black on a white background within a red square frame set on a point (i.e., a red diamond). The specific pictograms that are required on a label would be determined based on the hazard classification of the substance in question.

OSHA believes that the proposed pictograms would make warnings on labels more noticeable and easier for employees to understand. In particular, symbols are expected to improve comprehension among people with low literacy and those who are not literate in the English language. It should be remembered that pictograms would be used not only in conjunction with other label elements, but in the context of the hazard communication program as a whole. Training that includes an explanation of labels (included in the proposed rule) would ensure that pictograms are understood by employees.

A considerable amount of evidence supports the belief that pictograms can serve as useful and effective communication tools. In reviewing this evidence, it should be noted that some sources offer distinct definitions for “pictogram,” “pictorial,” “symbol,” and other terms describing graphical elements. For example, Rogers et al. state that: “Pictorials refer to pictures that represent the concept of interest (e.g., a picture of a fire extinguisher). Symbols are more abstract representations of a concept, the meaning of which must be learned (e.g., the use of a skull and crossbones to denote poison)” (Rogers et al., 2000). ANSI and others combine these terms in the definition of “symbol,” however, and for the purposes of discussing the literature on this subject, these terms are used interchangeably.

Symbols serve several important functions in warning labels. As Wogalter et al. explain, symbols may alert the user to a hazard more effectively than text alone:

Symbols may be more salient than text because of visual differentiations of shape, size, and color. Usually symbols have unique details and possess more differences in appearance than do the letters of the alphabet. Letters are highly familiar and are more similar to one another than most graphical symbols (Wogalter et al., 2006).

Symbols also can bolster a text message and improve label comprehension among individuals with low literacy, and those who do not understand the language in which the label text is written (Parsons et al., 1999).

Several researchers have sought to evaluate how people comprehend symbols, including those symbols that are incorporated in the proposed rule. Some studies have found that the skull and crossbones icon—one of the symbols included in the proposed rule—is among the most recognizable safety symbols. For example, Wogalter et al. asked 112 undergraduates and community volunteers to rank various label elements (Wogalter et al., 1998). Among shapes and icons, the skull symbol (in this case, without the crossbones) was rated most hazardous and most noticeable. The skull connoted the greatest hazard among industrial employees as well. Smith-Jackson and Wogalter asked 48 English-speaking workers to rate the perceived hazards of six alerting symbols (Smith-Jackson and Wogalter, 2000). The skull was rated significantly higher than all other symbols.

Some research has examined other pictograms included in the proposed rule. As part of an experiment to see how individuals comprehend warnings on household chemical labels, Akerboom and Trommelen asked 60 university students whether they understood the meaning of several pictograms, including four that are included in the proposed rule (Akerboom and Trommelen, 1998). The authors reported the following levels of comprehension for these pictograms:

  • Flame: 93 percent comprehension;
  • Skull and crossbones: 85 percent comprehension;
  • Corrosion: 20 percent comprehension; and
  • Flame over circle: 13 percent comprehension.

Only the flame and skull and crossbones pictograms met the 85 percent comprehension criteria suggested by ANSI Z535.3 (the American National Standard Criteria for Safety Symbols) (ANSI, 2002a). The authors recommend that labels present the hazard phrase [statement] and symbol together, along with corresponding precautions, as would be required under the proposed rule.

Banda and Sichilongo tested comprehension of labels that included the proposed pictograms among 364 workers in four sectors in Zambia (transport, agriculture, industrial, and household consumers) (Banda and Sichilongo, 2006). Within this population, the skull and crossbones symbol was widely understood, as was the “flame” symbol. Based on these results, the authors suggest a preference for symbols that depict familiar, meaningful, and recognizable images.

London performed a similar study among the same four sectors in South Africa, finding that the skull and crossbones was understood by at least 96 percent of each sector and “flame” by at least 89 percent (London, 2003). “Exploding bomb” was correctly comprehended by 44 to 71 percent of each sector. Many health-related symbols did not fare well, and six symbols had less than 50 percent comprehension across all four sectors. Outside the transport sector, “Gas cylinder” was the least well comprehended symbol.

These findings indicate that some of the pictograms included in the proposed rule are already widely recognized by a general audience. Others, however, are not commonly understood. Therefore, simply adding some of the proposed pictograms on labels will not provide useful information unless efforts are also undertaken to ensure that employees understand the meaning of the pictograms. As Wogalter et al. noted, some studies have found slower processing, poorer recognition, and greater learning difficulties with symbols versus with text—particularly if the symbols are complex or non-intuitive (Wogalter et al., 2006). These results emphasize the need to train employees on the meaning of the pictograms that would be included on chemical labels.

Where pictograms are used and understood, communication of hazards can be improved. Houts et al. studied long-term recall of spoken medical instructions when accompanied by a handout with pictograms (Houts et al., 2001). Nearly 200 pictograms were tested with 21 low-literate adults (less than grade 5 reading level). Immediately after training, participants recalled the meaning of 85 percent of the pictograms, and they recalled 71 percent after 4 weeks. This study found that recall was better for simple pictograms where there is a direct relationship between the image and its meaning—that is, where no inference is required.

Another body of literature focuses on the utility of symbols in general. Ganier found that people generally construct mental representations faster with pictures than they do with text, supporting earlier findings on the usefulness of symbols (Ganier, 2001). Evans et al. found similar results with a task in which undergraduates were asked to sort items into categories using either text clues, visual clues, or a combination of pictures and text (Evans et al., 2002). When categories were fixed (i.e., sorting instructions were specific), people sorted the cards more consistently with one another when presented with pictures than when presented with text alone.

In a follow-up article on the South African study mentioned previously, Dowse and Ehlers found that patients receiving antibiotics adhered to instructions much better when the instructions included pictograms (54 percent with high adherence, versus 2 percent when given text-only instructions) (Dowse and Ehlers, 2005).

Pictograms also serve to attract attention to the hazard warnings on a label. To examine factors that influence the effectiveness of pharmaceutical labels, Kalsher et al. asked subjects to rate the noticeability, ease of reading, and overall appeal of labels with or without pictorials (Kalsher et al., 1996). A group of 84 undergraduates gave consistently higher ratings to labels with pictorials. A group of elderly subjects had similar preferences, rating labels with pictorials as significantly more noticeable and likely to be read.

Laughery et al. found similar results with a timed test on alcoholic beverage labels (Laughery et al., 1993). When a pictorial was present to the left of the warning showing what not to do when drinking, the amount of time it took to find the label was significantly reduced. An icon consisting of the alert symbol (an exclamation mark set within a triangle) and the signal word WARNING also decreased response time. The fastest response time came when four different enhancements (including the pictorial and the icon) were included. In a follow-up exercise, an eye scan test found that the pictorial had a particularly strong influence on reaction time, compared with other enhancements.

As far as chemical labels are concerned, London found that symbols tend to be the most easily recalled label elements (London, 2003). In the comprehensibility test of labels among South African workers mentioned previously, symbols were the most commonly recalled elements—particularly the skull and crossbones—and people recalled looking at symbols first. Symbols were also cited as by far the most important factor in determining hazard perception. Overall, the author concludes that “Symbols are therefore key to attracting attention, and informing risk perception regarding a chemical.”

Wogalter et al. found less encouraging evidence on pictorials, however (Wogalter et al., 1993). The authors tested the influence of various warning variables on whether subjects wore proper protective equipment during a task involving measuring and mixing chemicals. Warning location and the amount of clutter around the warning had significant effects on compliance, but the presence or absence of pictorials did not.

Meingast asked subjects to recall warning content after viewing labels that were considered either high quality (with color signal icons, pictorials, and organized text conforming to ANSI Z535.4, the American National Standard for Product Safety Signs and Labels) or low quality (text only) (Meingast, 2001). Pictorials were the items remembered most often, accounting for 48 percent of what viewers of high quality labels recalled. The author suggests that these pictorials also served the role of dual coding, meaning that they help to improve the retention of corresponding text.

Other recent studies support this dual-coding function of pictorials, finding that symbols tend to be most effective when paired with redundant or reinforcing text. For example, Sojourner and Wogalter asked 35 participants to rate several prescription label formats in terms of ease of reading, ease of understanding, overall effectiveness, likelihood of reading, overall preference, pictorial understanding, and how helpful pictorials are in helping to remember the instructions (Sojourner and Wogalter, 1997). The authors found that people prefer fully redundant text and pictorials, which they judged easiest to read, most effective, and preferred overall. Dual-coded pictorials aided understanding and memory more than labels with pictorials only (no text). In a follow-up study, Sojourner and Wogalter gave undergraduates, young adults, and older adults a free recall test after viewing medication labels (Sojourner and Wogalter, 1998). Fully redundant text and pictorials led to significantly greater recall than other formats, and were rated most effective by all age groups.

Similarly, Sansgiry et al. found that pictograms on over-the-counter drug labels improved comprehension, but only when they were congruent with the corresponding text (Sansgiry et al., 1997). A group of 96 adults were less confused, more satisfied, more certain about their knowledge, and understood more when shown labels that contained congruent pictures and verbal instructions, versus verbal instructions alone. The results were significantly better with congruent pictures and text than with either pictures alone or incongruent pictures and text.

Some evidence links use of pictograms directly to safer behavior. Jaynes and Boles investigated whether different warning designs, specifically those with symbols, affect compliance rates (Jaynes and Boles, 1993). Five conditions were tested: a verbal warning, a pictograph warning with a circle enclosing each graphic, a pictograph warning with a triangle on its vertex enclosing each graphic, a warning with both words and pictographs, and a control (no warning). Participants performed a chemistry laboratory task using a set of instructions that contained one of the five conditions. The warnings instructed them to wear safety goggles, mask and gloves. All four warning conditions had significantly greater compliance than the no-warning condition. A significant effect was also found for the “presence of pictographs” variable, suggesting that the addition of pictographs will increase compliance rates.

In addition to the evidence pertaining to the other graphical elements in pictograms, research indicates that the use of the color red in pictograms will serve to make warnings more noticeable. Red is also generally perceived to reflect the greatest degree of hazard, and is thus well-suited to identifying serious chemical hazards in the workplace.

In their review of the literature on warning effectiveness on behavioral compliance, Kalsher and Williams summarize several studies that examined the effects of adding color to warnings (Kalsher and Williams, 2006). Overall, Kalsher and Williams suggest that adding color can influence both the noticeability and effectiveness of warnings.

In a test on the noticeability of warnings, Swindell measured the amount of time it took subjects to locate warning text that had been embedded in medication instructions (Swindell, 1999). Warnings were found significantly faster when the icon and signal word were presented in either red or blue, causing the warning to stand out from the black text. Swindell's findings echo the results reported by Laughery et al., who found that alcoholic beverage labels were located significantly faster when the text was red instead of black (Laughery et al., 1993). While these studies involve color on label elements other than the pictogram border, they provide a general indication that color attracts the attention of label users.

A number of researchers have investigated the hazard connotations of different colors. These investigations indicate that red is generally perceived to reflect the greatest degree of hazard. Yellow, orange, and black reflect a lesser degree of hazard. In a review of the literature, Parsons et al. suggest that the red-orange-yellow hierarchy generally matches people's perceptions of risk, including perceptions among native Spanish speakers (Parsons et al., 1999). Experimental results that support the conclusion that red generally connotes the highest degree of hazard include:

■ Smith-Jackson and Wogalter asked English-speaking community members to rate the perceived hazard of ten ANSI safety colors (Smith-Jackson and Wogalter, 2000). Red, yellow, black, and orange were rated the highest (in descending order). Differences were statistically significant except the difference between yellow and black.

■ Among 80 college students asked to rate colors by Griffith and Leonard, red was rated the most “meaningful” color (i.e., most distinct in meaning from neutral gray), followed by green, orange, black, white, blue, and yellow (Griffith and Leonard, 1997).

■ Wogalter et al. asked Spanish speakers to rank the perceived hazard of ANSI safety colors (Wogalter et al., 1997b). Red was ranked highest, followed by orange, black, and yellow.

■ Dunlap et al. surveyed 1169 subjects across several different language groups including English, German, and Spanish speakers (Dunlap et al., 1986). Subjects rated the color words red, orange, yellow, blue, green, and white according to the level of perceived hazard. The results demonstrated that the hazard information communicated by different colors followed a consistent pattern across language groups, with red having the highest hazard ratings.

■ Wogalter et al. asked undergraduates and community volunteers to rank various warning components (Wogalter et al., 1998). Red connoted a significantly greater hazard than other colors, followed by yellow, orange, and black (in that order). A group of industrial workers ranked the colors from greatest to least hazard as follows: red, yellow, black, orange.

■ London asked workers in four sectors in South Africa to rank the colors red, yellow, green, and blue in terns of perceived hazard; 95 percent said red represents the greatest hazard, and 58 percent said yellow is the second greatest hazard (London, 2003).

■ Banda and Sichilongo asked workers in Zambia to rate the perceived hazard of various colors used in chemical labels (Banda and Sichilongo, 2006). Red was associated with the greatest hazard, followed by yellow.

■ Among a sample of 30 undergraduates who rated the perceived hazard of 105 signal word/color combinations, Braun et al. reported that red conveyed the highest level of perceived hazard followed by orange, black, green, and blue (Braun et al., 1994).

These reports are consistent in indicating that red is commonly understood to be associated with a high level of hazard—the highest of any color. OSHA anticipates that by using the color red on labels for hazardous chemicals, labels will be more effective in communicating hazards to employees—both by drawing the attention of employees and indicating the presence of a hazard through non-verbal means.

Hazard and Precautionary Statements

Hazard statements describe the hazards associated with a chemical. Precautionary statements describe recommended measures that should be taken to protect against hazardous exposures, or improper storage or handling of a chemical. The HCS currently includes a performance-oriented requirement for “appropriate hazard warnings” on labels. The proposed rule would require specific hazard statements and precautionary statements on labels. The statements would be determined based on the hazard classification of the chemical.

Standardized requirements for hazard and precautionary statements would provide a degree of consistency that is currently lacking among chemical labels. This lack of consistency makes it difficult in some instances for users to understand the nature and degree of hazard associated with a chemical, and to compare chemical hazards. For example, Beach relates experiences from the perspective of a doctor treating occupationally exposed patients (Beach, 2002). The author noted that different suppliers use different risk phrases for the same chemical, making it difficult for users to compare relative risks.

ANSI standard Z129.1 was developed to provide a consistent approach to labeling of hazardous chemicals. This standard gives manufacturers and importers guidance on how to provide information on a label, including standardized phrases and other information that can improve the quality of labels. Because it is a voluntary standard, however, the ANSI approach has not been adopted by all chemical manufacturers and importers. As a result of the diverse formats and language used, consistent and understandable presentation of information has not been fully achieved.

A preference for hazard statements was shown in EPA's Consumer Labeling Initiative (Abt Associates, 1999). This study asked consumers about their attitudes toward labels on household chemical products. Overall, consumers indicated that they like to have information that clearly connects consequences with actions, and they prefer to know why they are being instructed to take a particular precaution. A clear hazard statement can provide this information.

In some cases, clear and concise precautionary information is necessary to enable employees to identify appropriate protective measures. For example, Frantz et al. examined the impact of flame and poison warning symbols prescribed in certain regulations by the Canadian government (Frantz et al., 1994). The results suggest that although the generic meanings of these two symbols are well understood, people may have difficulty inferring the specific safety precautions necessary for a particular product.

Other reports have indicated that users prefer information that includes both an indication of the hazard and the recommended action (i.e., the precautionary statement). Braun et al. examined statements in product instructions for a pool treatment chemical and a polyvinyl chloride (PVC) adhesive, asking subjects to rate the injury risk posed by each product (Braun et al., 1995). The experimenters manipulated the instructions to include either recommended actions only, actions followed by consequences, consequences followed by actions, or a simple restatement of the product label. The authors found that actions paired with consequences led to significantly higher risk perception than a restatement of the label or actions alone. Although the preferred wording was longer than the alternatives, subjects did not feel that the instructions were too complex, suggesting that they appreciate having actions and consequences paired together. Freeman echoed these findings in a discussion on communicating health risks to fishermen and farmers, noting that to be useful, risk statements should be balanced with equally strong statements of ways to reduce or avoid the risk (Freeman, 2001).

Explicit precautionary statements may make it more likely that employees will take appropriate precautions. Bowles et al. asked subjects to review product warnings, then either decide what actions they should take or evaluate whether someone else's actions were safe, based on the warning (Bowles et al., 2002). In general, situations that required the user to make inferences about a hazard—particularly when they had to come up with their own ideas for protective actions—led to decreased intent to comply. By providing clear precautionary instructions on the label, the proposed rule would eliminate the need for users to infer protective actions.

Some evidence indicates that using key label elements together can improve warning performance, compared with labels that only contain a subset of these elements. This is the approach taken in the proposed rule, which would require the signal word, pictogram(s), hazard statement(s), and precautionary statement(s) together on the label. In one study, Meingast asked students to recall information from two variations of warning labels: enhanced warnings with color, signal icons, pictorials, and organized text (following the ANSI Z535.4 standard); and warnings with text only (Meingast, 2001). The authors reported that the enhanced warnings were more noticeable, led to significantly greater recall, and made people report a higher likelihood of compliance.

Other findings agree that improving all label elements can improve warning performance. For example, Lehto tested information retrieval from three chemical label formats and found that subjects generally did best with an “extensive” format that included pictograms, paragraphs, and horizontal bars indicating the degree of hazard (Lehto, 1998). Subjects were able to answer more questions correctly when the label included a range of content—particularly information on first aid and spill procedures.

Wogalter et al. reported similar results in a test of four different signs that discouraged people from using an elevator for short trips (Wogalter et al., 1997a). Three signs were text-only. The fourth sign had a signal word panel, icons, a pictorial, and more explicit wording indicating the desired behavior (i.e., “use the stairs”). Subjects rated the enhanced sign as more understandable, and a field test found that it significantly increased compliance over the other options.

The effectiveness of a combination of elements was also investigated in a study of warnings on alcoholic beverage containers (Laughery et al., 1993). Laughery et al. tested warnings to determine which elements influenced noticeability. The authors manipulated labels by adding a pictorial, adding an alert symbol with a signal word, making the text red, and/or adding a border around the warning. The warning was located fastest when all four of these modifications were present, suggesting that the best designs include a combination of enhancements.

These findings support the belief that the proposed label elements, in combination, would likely be more effective in communicating hazard information than the individual elements would be if presented alone. Although the warnings examined in these studies are different than those included in the proposed rule, they indicate that enhancements such as color and symbols can increase the effectiveness of a label, and that presenting hazard information and corresponding precautions together may improve understanding. OSHA therefore believes that this evidence substantiates its belief that the proposed labeling requirements will result in more effective transmittal of information to employees.

Overall, the presentation of information on labels through standardized signal words, hazard statements, pictograms, and precautionary statements would provide clearer, more consistent, and more complete information to chemical users. Comments received in response to the ANPR support this view (e.g., Document ID #s 0054, 0032, 0124, 0124, and 0158). For example, the Refractory Ceramic Fibers Coalition (Document ID #0030) pointed to the benefits of this approach, stating:

Employers and employees would be given the same information on a chemical regardless of the supplier. This consistency should improve communication of the hazards. It may also improve communication for those who are not functionally literate, or who are not literate in the language written on the label. In addition, having the core information developed already, translated into multiple languages, and readily available to whomever wishes to access it, should eliminate the burden on manufacturers and users to develop and maintain their own such systems. Thus the specification approach should be beneficial both to the producers and the users of chemicals.

Labels are intended to provide an immediate visual reminder of chemical hazards. Whereas labels currently may be presented in a variety of formats using inconsistent terminology and visual elements, labels prepared in accordance with the proposed requirements would be consistent. Standardized signal words and hazard statements would attract attention and communicate the degree of hazard. Pictograms would reinforce the message presented in text and enhance communication for low-literacy populations. Precautionary statements would provide useful instructions for protecting against chemical-source injuries and illnesses.

Safety Data Sheets

The HCS requires chemical manufacturers and importers to develop an SDS for each hazardous chemical they produce or import. SDSs serve as a source of detailed information on chemical hazards and protective measures. Each SDS must indicate the identity of the chemical used on the label; the chemical and common name(s) of hazardous ingredients; physical and chemical characteristics; physical and health hazards; the primary route(s) of entry; exposure limits; generally applicable precautions for safe handling and use; generally applicable control measures; emergency and first aid procedures; the date of preparation of the SDS; and the name, address and telephone number of the party preparing or distributing the SDS. The HCS does not require this information to be presented in any particular order or to follow a specific format.

Since the HCS was adopted in 1983, access to chemical information has improved dramatically due to the availability of SDSs. While the effectiveness of SDSs is evident, there are concerns regarding the quality of information provided. In particular, concerns have been raised regarding the accuracy (i.e., the correctness and completeness of the information provided) and comprehensibility (i.e., the ability of users to understand the information presented) of information provided on SDSs.

OSHA is proposing a requirement that the information on SDSs be presented using consistent headings in the sequence specified in the GHS (see Section XV for a detailed discussion of the proposed requirements). The Agency believes that a standardized order of information would improve the utility of SDSs by making it easier for users to locate and understand the information they are seeking. A standardized format would also be expected to improve the accuracy of the information presented on SDSs.

A number of studies have demonstrated the benefits provided by SDSs. In May 1992, the General Accounting Office (GAO) issued a report presenting the findings of an examination of difficulties small employers were said to experience in complying with the HCS, as well as issues relating to the costs of compliance (GAO, 1992). The findings were based on the results of a national survey of construction, manufacturing, and personal services providers. A total of 1,120 responses were received from employers.

One very important finding of the GAO survey was that almost 30% of employers reported that they had replaced a hazardous chemical with a less hazardous substitute because of information presented on an SDS. With regard to the HCS as a whole, GAO found that over 56% of employers reported “great” or “very great” improvement in the availability of hazard information in the workplace and in management's awareness of workplace hazards. Forty-five percent of those in compliance with the HCS considered the standard to have a positive effect on employees, compared with only 9% who viewed the effect as negative. The results indicate that when chemical hazard information is provided, the result is generally recognized as beneficial to employees.

A number of other studies support this conclusion. For example, in a survey of 160 workers at a large national laboratory, more than 90 percent of respondents said that SDSs are satisfactory or very satisfactory in providing protective information and answering questions (Phillips et al., 1999).

Conklin demonstrated the utility of SDSs among employees of a multinational petrochemical company (Conklin, 2003). Across three countries (the U.S., Canada, and the United Kingdom), 98 percent felt that the SDS is a satisfactory information source (the percentage was similar across all three countries). Seventy-two percent said they would request an SDS all or most of the time when introduced to a new chemical, although 46 percent of workers said that SDSs are too long. The author notes, however, that this sample did not include any workers with low literacy.

A number of investigations have raised concerns that, in some cases, the information on SDSs is not comprehensible to employees. In 1991, OSHA commissioned a study that evaluated the comprehensibility of SDSs by a group of unionized employees in manufacturing industries located in the State of Maryland (Kearney/Centaur, 1991). The study assessed the ability of these employees to understand information regarding the route of entry of the substance, the type of health hazard present, appropriate protective measures, and sources of additional help.

Each of the 91 participating workers was provided with and tested on four different SDSs. The workers answered the test questions based on information supplied on each of the SDSs. It should be noted that the employees who volunteered for this study understood that it relied on reading comprehension. This created a selection bias, as employees with reading difficulties would not be likely to volunteer for the study.

The results of the tests indicated that workers on average understood about two-thirds of the health and safety information on the SDSs. The best comprehension was associated with information providing straightforward procedures to follow (e.g., in furnishing first aid, dealing with a fire, or in using personal protective equipment) or descriptions of how a chemical substance can enter the body. Workers had greater difficulty understanding health information addressing different target organs, particularly when more technical language was used. Workers also reportedly had difficulty distinguishing acute from chronic effects based on information presented in the SDSs.

A similar result was reported by Conklin in a study involving employees of a multinational petrochemical company (Conklin, 2003). After viewing information on an unfamiliar chemical in a variety of SDS formats, a questionnaire was administered to workers to gauge their comprehension of the material presented. The workers reportedly answered 65 percent of the questions correctly.

A study that examined the comprehensibility of SDS to master printers was reported by the Printing Industries of America in 1990 (PIA, 1990). The subjects had an average of 13.9 years of formal education, or approximately two years beyond high school. In this study, 27 SDSs were selected and analyzed for reading levels using a software program, finding an average reading grade level of 14. The investigators found that employees with 15 years of education or more understood 66.2% of the information presented.

Some of the difficulty workers experience in understanding information presented on SDSs may be due to the vocabulary used in the document. Information presented at a reading level that exceeds the capability of the user is unlikely to be well understood. An example of this situation was reported by Frazier et al. (Frazier et al., 2001). The authors evaluated a sample of SDSs from 30 manufacturers of toluene diisocyanate, a chemical known to cause asthma. Half of the SDSs indicated that asthma was a potential health effect. One SDS made no mention of any respiratory effects, while others used language (e.g., allergic respiratory sensitization) that the authors believed may not clearly communicate that asthma is a risk. However, the more technical language meets the requirements of the HCS.

Other reports substantiate the belief that many SDS users have difficulty understanding the information on the documents. For example, in a study evaluating the comprehensibility of SDSs at a large research laboratory, 39 percent of the workers found SDSs “difficult to understand” (Phillips, 1997). The study also indicated that a third of the information provided on SDSs was not understood. These results were obtained from a study population of literate, trained workers who spoke English as their first language.

Smith-Jackson and Wogalter corroborated this finding in a study involving 60 undergraduates and community volunteers (Smith-Jackson and Wogalter, 1998). The subjects were asked to sort SDS data into a logical order. After completing the task, subjects were asked for their opinions on the difficulty of the content. Overall, 43 percent found the information easy to understand, 42 percent said it was not easy, and the remaining 15 percent felt that only scientists, experts, or very experienced workers would be able to understand the information.

These studies are consistent in reporting that workers have difficulty understanding a substantial portion of the information presented on SDSs. This finding can be explained at least in part by the fact that not all of the information on SDSs is intended for workers. SDSs are intended to provide detailed technical information on a hazardous chemical. While they serve as a reference source for exposed employees, SDSs are also meant for other audiences as well. SDSs provide information for the benefit of emergency responders, industrial hygienists, safety professionals, and health care providers. Much of this information may be of a technical nature and would not be readily understood by individuals who do not have training or experience in these areas. For example, language that may be readily understood by a population of firefighters may be poorly understood by chemical workers.

In addition, Title III of the Superfund Amendments and Reauthorization Act (SARA, also known as the Emergency Response and Community Right-to-Know Act of 1986) mandated that SDSs be made available to State emergency response commissions, local emergency planning committees, and fire departments in order to assist in planning and response to emergencies, as well as to provide members of the general public with information about chemicals used in their communities. It is difficult, if not impossible, for a document to meet the informational needs of all of these audiences while being comprehensible to all as well.

Product liability concerns also play a role in the comprehensibility of SDSs. Producers of chemicals may be subject to “failure to warn” lawsuits that can have significant financial implications. Attempts to protect themselves against lawsuits can affect the length and complexity of SDSs, as well as the way in which information is presented.

In some cases the length and complexity of SDSs reportedly make it difficult to locate desired information on the documents. For example, in testimony before the U.S. Senate Subcommittee on Employment, Safety, and Training, one hospital safety director described a situation in which an employee was unable to find critical information on an SDS in an emergency situation:

* * * two gallons of the chemical xylene spilled in the lab of my hospital. By the time an employee had noticed the spill, the ventilation had already sucked most of the vapors into the HVAC. This, in turn, became suspended in the ceiling tile over our radiology department. Twelve employees were sent to the emergency room. To make the matter worse, the lab employee was frantically searching through the MSDS binder in her area for the xylene MSDS. Once she found it, she had difficulty locating the spill response section. After notifying our engineering department, she began to clean up the spill with solid waste rags, known for spontaneous combustion, and placing the rags into a clear plastic bag for disposal. She did not know that xylene has a flash point of 75 degrees Fahrenheit. She then walked the bag down to our incinerator room and left it there, basically creating a live bomb. Twelve people were treated from this exposure. The lab employee was very upset and concerned about the safety of the affected employees and visitors, and hysterically kept stating that she could not find the necessary spill response information (Hanson, 2004).

SDSs at this particular hospital were reported to range from one page to 65 pages in length.

To accommodate the needs of the diverse groups who rely on SDSs, a standardized format has been viewed as a way to make the information on SDSs easier for users to find, and to segregate technical sections of the document from more basic elements. A standardized format was also thought to facilitate computerized information retrieval systems and to simplify employee training.

OSHA established a voluntary format for SDSs in 1985 to assist manufacturers and importers who desired some guidance in organizing SDS information. This 2-page form (OSHA Form 174) includes spaces for each of the items included in the SDS requirements of the standard, to be filled in with the appropriate information as determined by the manufacturer or importer. However, some members of the regulated community desired a more comprehensive, structured approach for developing clear, complete, and consistent SDSs.

In order to develop this structure, the Chemical Manufacturers Association (now known as the American Chemistry Council) formed a committee to establish guidelines for the preparation of SDSs. This effort resulted in the development of American National Standards Institute (ANSI) standard Z400.1, a voluntary consensus standard for the preparation of SDSs. Employers, workers, health care professionals, emergency responders, and other SDS users participated in the development process. The standard established a 16-section format for presenting information as well as standardized headings for sections of the SDS. An updated version of the ANSI standard published in 2004 is consistent with the GHS format that is included in the proposed rule.

By following the recommended format, the information of greatest concern to employees is featured at the beginning of the document, including information on ingredients and first aid measures. More technical information that addresses topics such as the physical and chemical properties of the material and toxicological data appears later in the document. The ANSI standard also includes guidance on the appearance and reading level of the text in order to provide a document that can be easily understood by readers.

OSHA currently allows the ANSI format to be used as long as the SDS includes all of the information required by the HCS. Because it is a voluntary standard, however, the ANSI format has not been adopted by all chemical manufacturers and importers. As a result, different formats are still used on many SDSs.

The International Organization for Standardization (ISO) has published its own standard for SDS preparation. This standard, ISO 11014-1, has been revised for consistency with the GHS (new version issued in 2009). The standard includes the same 16 sections as the GHS, as well as similar data requirements in each section. These two consensus standards, ANSI Z400.1-2004 and ISO 11014-1 (2009), have essentially the same provisions and are consistent with GHS. There are minor differences, such as units of measure recommended in the national ANSI standard versus the international ISO standard.

Another development has been the creation of International Chemical Safety Cards (ICSCs). The documents, developed by the International Programme on Chemical Safety, summarize essential health and safety information on chemicals for use at the “shop floor” level by workers and employers (Niemeier, 1997). ICSCs are intended to present information in a concise and simple manner, and they follow a standardized format that is shorter (one double-sided page) and less complex than the ANSI approach. The ICSCs were field tested in their initial stages of development, and new ICSCs are verified and peer reviewed by internationally recognized experts (Niemeier, 1997). ICSCs have been developed in English for 1,646 chemicals, and are also available in 16 other languages. The ICSCs are being updated to be consistent with the GHS.

A study by Phillips compared the effectiveness of different SDS formats as well as ICSCs among workers at a large national laboratory (Phillips, 1997). The employees represented a variety of trades, including painters, carpenters, truck drivers, and general laborers. Each worker was tested for knowledge regarding a hazardous chemical before and after viewing an SDS or ICSC. Three designs were tested: a 9-section OSHA form, the 16-section ANSI Z400.1 format (an earlier and slightly different version of the current ANSI Z400.1 format), and the 9-section ICSC. A subsequent paper described the final results of this study (Phillips, 1999). All three formats led to significant improvements in subjects' knowledge, and there was no statistically significant difference among the three formats in terms of total test score. However, there were a few significant differences in how well readers of each SDS format answered specific types of questions:

  • The ICSC performed better than the OSHA form regarding chronic and immediate health effects.
  • The other two formats performed better than the ANSI format on fire-related questions.
  • The OSHA form performed better than the other two formats on spill response questions.
  • The OSHA form was better than the ANSI format regarding carcinogenic potential.

In a separate comparison, Conklin also found similarities in the overall performance of several standard SDS formats (Conklin, 2003). In this study, employees of a multinational petrochemical company were given one of three versions of an SDS for an unfamiliar chemical: a U.S. version (OSHA's required content within an ANSI Z400.1-1998 16-part structure); a Canadian version following the 9-part structure prescribed by Canada's Workplace Hazardous Materials Information System (WHMIS); and a version following the European Union's content and 16-part structure. SDSs were controlled for font, layout, and reading level. Overall, Conklin found no statistically significant difference in mean post-test scores using the three different formats, although there were significant differences on 5 out of 10 questions (no one format was consistently better).

Because extensive searching can be a barrier to SDS use, researchers have examined whether there is a preferred order of information that more closely matches users' cognitive expectations. Smith-Jackson and Wogalter asked 60 undergraduates and community volunteers to arrange portions of six SDSs in the order they considered most usable (Smith-Jackson and Wogalter, 1998). The authors found a few consistent results:

  • Information about health hazards, protective equipment, and fire and explosion data tended to be placed toward the beginning.
  • Physical and reactivity data tended to be placed near the end.
  • Spill or leak procedures were placed near the beginning or the middle, depending on the type of chemical.

A majority of subjects reported that they had attempted to prioritize the hazard information that needed to be communicated. The participants' suggested order of information generally did not match either the original SDS order or the order listed in the HCS—particularly the subjects' emphasis on health hazard information near the beginning.

In the previously discussed 1991 study that evaluated the comprehensibility of SDSs by a group of 91 unionized workers in manufacturing industries in the State of Maryland, a subset of the group (18 workers) was also tested on an ICSC (Kearney/Centaur 1991). While the results indicated that workers on average understood about two-thirds of the health and safety information on SDSs, ICSCs provided better results. The average ICSC test score ranged from 6% to 23% higher than the average test score on the four SDSs evaluated. This finding was considered by the authors to suggest that an improved format for SDSs may serve to increase user comprehension of the information presented.

OSHA believes that a standardized format would improve the effectiveness of SDSs. The primary basis for this belief is very simple: A consistent format would make it easier for users to find information on an SDS. Headings for SDS sections would be standardized, so SDS users would know which section to consult for the information they desire. The sections would be presented in a consistent, logical sequence to further facilitate locating information of interest. Information commonly desired by exposed employees and of greatest interest to emergency responders (e.g., Hazards Identification; First Aid Measures) would be presented in the beginning of the document for easy reference. More technical information (e.g., Stability and Reactivity; Toxicological Information) would be presented later.

By segregating more complex information on an SDS from the information that is generally easier to understand, the standardized format included in the proposed rule has the potential to address many of the concerns that have been raised regarding the comprehensibility of information on SDSs. The standardized order of information will allow SDS users who desire only basic information about a hazardous chemical to find that information without having to sift through a great deal of technical information that may have little meaning to them. In emergency situations, rapid access to information such as first-aid measures, fire-fighting measures, and accidental release measures can be critically important.

A standardized format does not address all issues affecting SDS comprehensibility. Reading level and some design elements would continue to vary. In many respects, this is inevitable given the different target audiences that SDSs have, and the varying qualifications of those who prepare SDSs. Nevertheless, OSHA believes that the proposed revisions will result in a substantial improvement in the quality and ease of comprehension of information provided on SDSs.

In addition to the issues regarding comprehensibility, a number of researchers have raised concerns that some SDSs may be incomplete or contain erroneous information. The magnitude of the problem is unclear, because only very limited numbers of SDSs have been evaluated in these studies and in some cases the investigations were performed so long ago that the results may not reflect current practices. Nevertheless, the evidence appears to indicate that a substantial number of SDSs may not contain complete and correct information.

An initial examination of the accuracy of SDSs was commissioned by OSHA shortly after the scope of the rule was expanded to cover all industries in 1987 (Karstadt, 1988). The report, which analyzed the content of 196 SDSs for products used in auto repair and body shops, provided a general indication that the content and presentation of information was inconsistent on the SDSs examined. In 1991, OSHA commissioned an additional study that examined the accuracy of SDSs (Kearnet/Centaur, 1991). The study examined information presented in five areas considered crucial to the health of workers potentially exposed to hazardous substances. These five areas assessed were chemical identification of ingredients; reported health effects of ingredients; recommended first aid procedures; use of personal protective equipment; and exposure level regulations and guidelines. The evaluation indicated that 37% of the SDSs examined accurately identified health effects data, 76% provided complete and correct first aid procedures, 47% accurately identified proper personal protective equipment, and 47% correctly noted all relevant occupational exposure limits. Only 11% of the SDSs were accurate in all four information areas, but more (51%) were judged accurate, or considered to include both accurate and partially accurate information, than were judged inaccurate (10%). The study also concluded that the more recent SDSs examined (those prepared between 1988 and 1990) appeared to be more accurate than those prepared earlier.

This belief that some SDSs are not complete and correct was corroborated by an examination of SDSs for lead and ethylene glycol ethers (Paul and Kurtz, 1994). Although these substances are known reproductive and developmental toxicants, researchers found that 421 of 678 SDSs examined (62%) made no mention of effects on the reproductive system. OSHA also commissioned a study, completed in 1999, focusing specifically on the accuracy of first aid information provided on SDSs (Lexington Group, 1999). A total of 56 SDSs for seven chemicals were examined. First aid information on the SDSs was compared with information from established references. The researchers reported that nearly all of the SDSs reviewed had at least minor inaccuracies.

A standardized format does not directly address the concerns that have been raised regarding the accuracy of information present on SDSs. However, standardization would improve the accuracy of chemical hazard information indirectly. With consistent presentation of information, the task of reviewing SDSs and labels to assure accuracy would be simplified. Individuals preparing and reviewing these documents should find it easier to identify any missing elements, and compare information presented on an SDS to reference sources and other SDSs. OSHA enforcement personnel would be able to more efficiently examine SDSs when conducting inspections. The detailed entries proposed for the SDS are particularly noteworthy in this regard. The sub-headings would provide an organized and detailed list of pertinent information to be included under the headings on the SDS. For example, while the HCS currently requires physical and chemical characteristics of a hazardous chemical to be included on the SDS, the proposed rule would provide a list of 18 properties for Section 9 of the SDS. The party preparing the SDS would either include the relevant information for these entries, or indicate that the information is not available or not applicable. This approach would provide both a reminder to the party preparing the SDS regarding the information required, and a convenient means of reviewing the section to ensure that relevant information is included and is accurate.

OSHA anticipates that the classification criteria included in the proposed rule would also improve the accuracy and precision of information on SDSs. The detailed criteria provided would direct evaluators to the appropriate classification for a chemical. For example, while directing the evaluator to use expert judgment in taking all existing hazard information into account, the criteria for serious eye damage/eye irritation is tied to specific results found in animal testing. In addition, assignment to hazard categories would lead to provision of detailed information that would be specific to the degree of hazard presented by the chemical.

Classification of hazards would also play an important role in increasing the usefulness of SDSs under the proposed rule. By including the classification of the substance on the SDS, employers would be in a much better position to compare the hazards of different chemicals. Hazard categories generally give an indication of the severity of the hazard associated with a chemical. For example, all other things being equal, a chemical classified for skin corrosion/ irritation in category 1 as a skin corrosive would be more hazardous than a chemical classified in category 2 as a skin irritant. If chemicals are classified into hazard categories, this information can be used to simplify the process of comparing chemicals. As noted previously, employers use SDSs as a means of comparing chemical hazards to select less hazardous alternatives. Thus it is reasonable to believe that the proposed rule would result in more effective use of the SDS as an instrument for identifying less hazardous substitutes for hazardous chemicals.

Support for a standard SDS format has been expressed consistently by a variety of stakeholders for a long period of time. The development of an industry consensus standard for preparation of SDSs, ANSI Z400.1, in itself, shows a desire on the part of many parties for a consistent approach to SDSs. As noted previously, ANSI Z400.1 was updated in 2004 to include the same sections and sequence as the proposed rule. Responses to OSHA's Request for Information in the Federal Register of May 17, 1990 (55 FR 20580) indicated widespread support for a standard SDS format, with many specifically supporting the ANSI format.

In its report of its evaluation of the HCS, the GAO included several recommendations. Among these was a recommendation that OSHA clearly specify the language and presentation of information on SDSs (GAO, 1991). In addition, the report of the National Advisory Committee for Occupational Safety and Health Review of Hazard Communication (September 12, 1996) indicated that during the public presentations and workgroup discussions, there was general agreement that a uniform format should be encouraged and most workgroup members agreed that OSHA should endorse use of the ANSI Z400.1 format (NACOSH, 1996).

Comments received in response to the ANPR also indicate widespread support for a standard format for SDS (e.g., Document ID #s 0054, 0064, 0030, 0124, and 0158). The American Foundry Society, for example, said that consistent SDSs make it easier for users to find information and compare products (Document ID #0158). The Jefferson County Local Emergency Planning Committee maintained that critical information can be missed by first responders due to the current lack of consistency in presentation of information on SDSs, stating: “It is not overreaching for us to say that lives will be saved through harmonization” (Document ID #0037). Based on the information in the record, OSHA thus believes not only that the proposed standardized SDS format would improve the quality of information provided on SDSs, but that stakeholders generally prefer a standardized format.

Training

Along with labels on containers and SDSs, employee training is one of three core components of a comprehensive hazard communication program. Training is needed to explain and reinforce the information presented on labels and SDSs, to ensure that employees understand the chemical hazards in their workplace and are aware of the protective measures to follow. The proposed rule includes a relatively minor revision to the HCS training requirements, intended to ensure that labels and SDSs are adequately explained to employees (see Section XV for a detailed discussion of the proposed requirements). In light of the evidence previously discussed relating to label and SDS comprehension, the importance of training should not be underestimated.

Training is necessary to ensure that employees understand the standardized heading and sequence of information on SDSs. Likewise, employees must be able to understand the meaning of the proposed standardized label elements in order for them to be effective. In certain instances, label elements already appear to be fairly well understood. For example, “Danger” already appears to be generally recognized to represent a higher degree of hazard than “Warning”. Other label elements, particularly some pictograms, are less well understood. This finding is not surprising given the limited amount of exposure that most of the population has had to these pictograms.

A relatively high level of understanding is generally recommended for pictograms. For example, ANSI Z535.3, the American National Standard that addresses criteria for safety symbols, contains a test method for determining the effectiveness of a pictogram. The criterion for success is 85% correct responses, with no more than 5% critical confusion. (Critical confusion refers to when the message conveyed is the opposite of the intended message.) A score below 85% does not mean the pictogram should not be used, but rather that it should not be used without some additional element, such as written text. The International Standards Organization has similar criteria in ISO 9186, Procedures for the Development and Testing of Public Information Symbols. This standard recommends testing methodologies to evaluate symbols intended to be used internationally. It sets a somewhat lower level of acceptability (66%) than the ANSI standard.

While initial understanding of some pictograms may not be satisfactory, research shows that training can improve comprehension. In one study, Wogalter et al. tested how well undergraduate subjects comprehended a set of 40 pharmaceutical and industrial safety pictorials before and after training (Wogalter et al., 1997c). Training led to a significant increase in pictorial comprehension. The improvement was greatest for the most complex symbols. Training was equally effective whether the subject was given a simple printed label (e.g.,“Danger, cancer-causing substance”) or a label with additional explanatory text.

Lesch conducted a similar study, testing how well workers recognized a set of 31 chemical and physical safety symbols before and after training (Lesch, 2002; 2003). Training significantly improved comprehension, which remained higher up to 8 weeks later. As in the Wogalter et al. study described above, Lesch found little difference in performance whether training took the form of a written label assigned to each symbol, a label plus explanatory text, or an accident scenario. Training also improved response speed.

In a survey of South African workers, London examined the impact of brief training on the meaning of symbols and hazard phrases (London, 2003). Here, the author found no statistical difference in comprehensibility of four familiar hazard symbols, but did find that training improved comprehension of one symbol (the proposed health hazard symbol), and it also reduced the overall incidence of critical confusion. This study also found that workers with previous workplace training were more likely to understand label text and some pictograms, and were better able to identify the active ingredient. A similar result was reported by Banda and Sichilongo in their evaluation of GHS labels in Zambia. The authors found that “correct responses to label elements were not a result of social class and/or age but appeared to be influenced by extent of duration of exposure either through specialized training or acquaintance” (Banda and Sichilongo, 2006). Recognizing that symbols are the items most often recalled from a label, London advised a strong emphasis on training for GHS symbols, particularly the “flame over circle” and “flame” symbols—which were reported to be easily confused—and symbols that may generate critical confusion (London, 2003).

These reports serve to reinforce OSHA's longstanding belief that labels, SDSs, and training are complementary parts of a comprehensive hazard communication program—each element reinforces the knowledge necessary for effective protection of employees. The need for training to ensure comprehension of hazard information is widely recognized. Annex A of ANSI Z535.2 (the American National Standard for Environmental and Facility Safety Signs), for example, recommends training on the meaning of standard safety symbols and signal words, and ANSI Z535.4 contains similar guidance.

It is a longstanding Agency position that employees have the “right to know” and understand the hazards of chemicals they are exposed to in the workplace (FR 53:29826; FR 59:6126). This knowledge is needed in order to take the precautions necessary for safe handling and use, to recognize adverse health effects associated with chemical exposure, and to respond appropriately in emergency situations.

Equally important in terms of employee protection is that employers have access to chemical hazard information as well. Chemical information is the foundation of workplace chemical safety programs—without it, sound management of chemicals cannot occur. By ensuring that emergency responders, physicians, nurses, industrial hygienists, safety engineers and other professionals have the information they need to devise protections, the HCS serves to reduce the likelihood of chemical source illnesses and injuries. Selection of appropriate engineering controls, work practices, and personal protective equipment is predicated knowing the chemicals that are present, the form they are present in, and their hazardous properties.

OSHA believes that the proposed requirements would improve the quality and consistency of the chemical hazard information provided to employers and employees. A combination of label elements—signal word, hazard statement(s), pictogram(s), and precautionary statement(s)—is expected to make label warnings more noticeable, easier to understand, and better communicate hazard and precautionary information. Standardized headings and a consistent order of information are anticipated to make it easier for users to find information on SDSs, improve their accuracy, and better enable users to compare the relative hazards of different substances. Along with effective training in the context of a comprehensive chemical hazard communication program, these revisions would serve to more adequately inform employees of chemical hazards, and lead to better protections in the workplace.

OSHA's preliminary determination to modify the HCS is based on its assessment of the potential to improve employee safety and health. While enhancing protection of employees is the Agency's objective in this rulemaking, implementation of the GHS is also anticipated to provide other benefits. As indicated in Section IV, modification of the HCS is expected to promote a range of objectives.

Many countries do not currently have regulatory requirements addressing chemical hazard communication. Those countries that do not have the resources to develop a regulatory system can use the GHS as a basis for establishing such requirements. Implementation in these countries will thus lead to dissemination of information about chemical hazards and protective measures to individuals who would not otherwise be afforded this benefit.

Transmittal of information provides a basis for the sound management of chemicals, which is beneficial not only to the country where it is practiced, but to neighboring countries as well. For example, uncontrolled releases of hazardous chemicals are not confined by national borders. A coordinated and harmonized approach to developing and providing chemical hazard information is beneficial to all.

The United Nations Institute for Training and Research (UNITAR) and the International Labor Organization (ILO) have initiated a program to support GHS implementation. The program provides assistance regarding development of national GHS implementation strategies, legislation, and other topics. UNITAR is supporting national GHS implementation and capacity building projects in Cambodia, Indonesia, Laos, Nigeria, Senegal, Slovenia, Thailand, the Gambia, and the Philippines, and has supported meetings, workshops, and regional activities as well. Over 80 countries have requested assistance from UNITAR/ILO, indicating widespread interest in GHS adoption throughout the world.

Adoption of the GHS is also expected to reduce the amount of testing performed to identify hazardous properties of chemicals. The HCS does not currently require testing of chemicals, and will not require testing with adoption of the GHS. However, testing is often performed to determine how a chemical will be classified under the various systems currently in place. By harmonizing definitions of hazards, such testing would be minimized, saving unnecessary use of test animals and associated costs.

Implementation of the GHS is expected to lessen the regulatory burden associated with classification of chemical hazards and labeling of hazardous chemicals. In the U.S., regulatory authorities with jurisdiction over the workplace, environment, consumer and transport sectors (i.e., OSHA, EPA, CPSC, and DOT) are not currently harmonized with regard to definitions of hazards and other requirements related to classification and labeling of chemicals. Widespread adoption of the GHS among the agencies would simplify the process of classifying chemicals and developing labels. For example, most chemicals are produced in a workplace and shipped elsewhere. As a result, manufacturers must comply with at least two sets of requirements that are currently not harmonized. Adoption of the GHS would simplify this process. Thus every chemical manufacturer would be likely to experience some benefits from harmonization, even if they are not involved in international trade.

For those who are involved in international trade in hazardous chemicals, the expected benefits would be even greater. As discussed in Section III, different countries have established requirements for chemical hazard classification, labeling, and SDSs that vary with regard to the scope of chemicals covered, definitions of hazards, the specificity of requirements, and the use of symbols and pictograms. Tracking the requirements of different regulatory authorities and developing different labels and SDSs is a burden for all manufacturers, importers, distributors, and transporters. Chemical manufacturers that do not have the resources to identify and comply with the requirements of regulatory authorities in different countries are precluded from engaging in trade with those countries. Small businesses are particularly affected. Implementation of the GHS would alleviate this burden and simplify the provision of chemical hazard information in international commerce.

VI. Pertinent Legal Authority Back to Top

The primary purpose of the Occupational Safety and Health Act (the “OSH Act” or “Act”) (29 U.S.C. 651 et seq.) is to assure, so far as possible, safe and healthful working conditions for every American employee over the period of his or her working lifetime. One means prescribed by the Congress to achieve this goal is the mandate given to, and the authority vested in, the Secretary of Labor to “promulgate, modify, or revoke” mandatory occupational safety and health standards. OSH Act § 6(b), 29 U.S.C. 655(b).

An occupational safety and health standard is defined under the Act as:

[A] standard which requires conditions, or the adoption or use of one or more practices, means, methods, operations, or processes, reasonably necessary or appropriate to provide a safe or healthful employment and places of employment.

OSH Act § 3(8), 29 U.S.C. 652(8). The Supreme Court has interpreted this provision as requiring OSHA to determine, before promulgating a permanent standard under section 6(b) of the Act, that the standard is reasonably necessary and appropriate to remedy a significant risk of material health impairment. Industrial Union Dep't v. American Petroleum Institute, 448 U.S. 607, 642 (1980) (“Benzene”). This “significant risk” determination constitutes a finding that, absent the change in practices mandated by the standard, the workplaces in question would be “unsafe” in the sense that employees would be threatened with a significant risk of harm. Id.

OSHA's Hazard Communication Standard (“HCS”) is a health standard promulgated under the authority of sections 6(b)(5) and 6(b)(7) of the Act. Associated Builders Contractors, Inc. v. Brock, 862 F.2d 63, 67-68 (3d Cir. 1988); United Steelworkers of America v. Auchter, 763 F.2d 728, 738 (3d Cir. 1985); United Steelworkers of America v. Auchter, 819 F.2d 1263, 1267 (3d Cir. 1987). Authority for the HCS may also be found in section 8(c) and 8(g) of the Act. Section 8(c)(1) of the Act empowers the Secretary to require employers to make, keep, and preserve records regarding activities related to the Act and to make such records available to the Secretary. 29 U.S.C. 657(c)(1). Section 8(g)(2) of the Act empowers the Secretary to “prescribe such rules and regulations as (she) may deem necessary to carry out (her) responsibilities under this Act * * *” 29 U.S.C. 657(g)(2).

Section 6(b)(5) provides that:

The Secretary, in promulgating standards dealing with toxic materials, or harmful physical agents under this subsection, shall set the standard which most adequately assures, to the extent feasible, on the basis of the best available evidence, that no employee will suffer material impairment of health or functional capacity even if such employee has regular exposure to the hazard dealt with by such standard for the period of his working life. Development of standards under this subsection shall be based upon research, demonstrations, experiments, and such other information as may be appropriate. In addition to the attainment of the highest degree of health and safety protection for the employee, other considerations shall be the latest available scientific data in the field, the feasibility of standards, and experience gained under this and other health and safety laws. Whenever practicable, the standard promulgated shall be expressed in terms of objective criteria and of the performance desired.

29 U.S.C. 655(b)(5). Thus, once OSHA determines that a significant risk due to a health hazard is present and that such risk can be reduced or eliminated by a proposed standard, section 6(b)(5) requires it to issue the standard, based on the best available evidence, that “most adequately assures” employee protection, subject only to feasibility considerations. As the Supreme Court has explained, in passing section 6(b)(5), “Congress * * * place[d] worker health above all other considerations save those making attainment of this benefit unachievable.”American Textile Manufacturers Institute, Inc. v. Donovan, 452 U.S. 490, 509 (1981) (“Cotton Dust”). Where, however, OSHA is confronted with two feasible methods of reducing risk to the appropriate level, OSHA must chose the cheaper method. Id. at 513 n.32; International Union, UAW v. OSHA, 37 F.3d 665, 668 (D.C. Cir. 1994).

In addition, section 6(b)(7) of the Act provides in part that:

Any standard promulgated under this subsection shall prescribe the use of labels or other appropriate forms of warning as are necessary to insure that employees are apprised of all hazards to which they are exposed, relevant symptoms and appropriate medical treatment, and proper conditions and precautions of safe use or exposure.

29 U.S.C. 655(b)(7). Section 6(b)(7)'s labeling and employee warning requirements provide basic protections for employees in the absence of specific permissible exposure limits, particularly by providing employers and employees with information necessary to design work processes that protect employees against exposure to hazardous chemicals in the first instance. The Supreme Court has recognized such protective measures may be imposed in workplaces where chemical exposure levels are below that for which OSHA has found a significant risk. Benzene, 448 U.S. at 657-58 n.66. In Benzene, the Court relied on § 6(b)(7) to uphold the imposition of exposure and medical monitoring requirements at exposures to benzene below the permissible exposure limit. Id. These requirements serve as a “backstop,” the Court said, allowing OSHA to check the validity of its assumptions in developing the PEL and employers to remove workers before they suffered any permanent damage. Id. at 657-58.

In making the determinations required by the Act, OSHA's conclusions must be “supported by substantial evidence in the record considered as a whole.” OSH Act § 6(f), 29 U.S.C. 655(f). OSHA must use the “best available evidence,” which includes “the latest scientific data in the field”; “research, demonstrations, experiments, and such other information as may be appropriate”; and “experience gained under this and other health and safety laws.” OSH Act § 6(b)(5), 29 U.S.C. 655(b)(5). The Supreme Court has held that OSHA is not required to support its finding of significant risk “with anything approaching scientific certainty,” and that the determination of whether a particular risk is “ ‘significant' will be based largely on policy considerations.”Benzene, 448 U.S. at 655-56 n.62.

The OSH Act allows the Secretary to “modify” and “revoke” existing occupational safety or health standards. OSH Act § 6(b), 29 U.S.C. 655(b). In passing the Act, Congress recognized that OSHA should revise and replace its standards as “new knowledge and techniques are developed.” S. Rep. 91-1282 at 6 (1970). The Supreme Court has observed that administrative agencies “do not establish rules of conduct to last forever, and * * * must be given ample latitude to adapt their rules and policies to the demands of changing circumstances.”Motor Vehicle Mfrs. Ass'n v. State Farm Mut. Automobile Ins. Co., 463 U.S. 29, 42 (1983) (internal quotation marks and citations omitted).

A. Significant Risk. Most OSHA health standards protect employees by imposing requirements when employees are exposed to a concentration of a hazardous substance that OSHA has found to create a significant risk of material health impairment. Thus, in making the significant risk determination in these cases, OSHA is concerned with measuring the exposure an employee may be expected to incur when dealing with these substances to determine the level at which a significant risk arises.

OSHA took a different approach to its significant risk determinations in promulgating the HCS in 1983 and revising it in 1994. Rather than attempting to assess the exposure—and therefore the risk—associated with the use of each hazardous chemical in each industry to determine if that chemical posed a significant risk in that industry, OSHA took a more general approach. It relied on NIOSH data showing that about 25 million or about 25% of American employees were potentially exposed to one or more of 8,000 NIOSH-identified chemical hazards and that for the years 1977 and 1978, more than 174,000 illnesses were likely caused by exposure to hazardous chemicals. 48 FR 53282. It then noted the consensus evident in the record among labor, industry, health professionals, and government that an “effective federal standard requiring employers to identify workplace hazards, communicate hazard information to employees, and train employees in recognizing and avoiding those hazards” was necessary to protect employee health. 48 FR 53283.

Thus, OSHA found that because

inadequate communication about serious chemical hazards endangers workers and that the practices required by this standard are necessary or appropriate to the elimination or mitigation of these hazards, the Secretary is hereby able to make the threshold “significant risk” determination that is an essential attribute of all permanent standards.

48 FR 53321. The U.S. Court of Appeals for the Third Circuit has on several occasions upheld this determination of significant risk as sufficient to justify the HCS under OSH Act § 6(b). See Associated Builders Contractors, 862 F.2d at 67 (discussing the history of its review of the issue).

A characteristic of hazard communication that OSHA confronted in adopting the HCS is that information about the hazards associated with a particular chemical, and the exposures associated with its use, are not uniformly distributed across industry. That is, chemical manufacturers and importers tend to have greater knowledge and scientific expertise with respect to the composition of the chemicals they make or import. See 48 FR 53306, 53322. Therefore, they are usually in the best position to assess the inherent hazards associated with them. Id. However, it is the downstream users and their employees who tend to have the best information about the means and methods of exposure, and are therefore usually in the best position to determine the risk arising from the use of the chemical in their workplaces. See 48 FR 53295-96, 53307; 59 FR 6132.

OSHA's approach in promulgating the HCS reflects this reality. It places the duty to ascertain and disclose chemical hazards on manufacturers and importers, so that downstream users can use this information to avoid harmful exposures to chemical hazards. But because manufacturers and importers will often have less information about the particular exposures of downstream users, their hazard assessment and communication obligations are imposed only for all normal conditions of use of their chemicals and foreseeable emergencies associated with those chemicals. 29 CFR 1910.1200(b)(2).

In previous rulemakings, OSHA rejected suggestions that these obligations should arise only where the downstream use creates a significant risk because it is difficult, if not impossible, for OSHA or manufacturers and importers to know where these risks might occur before the fact. 49 FR 53295-96; 59 FR 6132. Further, it is only by the provision of hazard information that downstream employers and employees can determine how to use the chemical so that exposure and risk may be minimized. Id. Thus, the HCS protects employees from significant risk by requiring communications about all chemicals that may present a hazard to employees, regardless of the exposure or risk levels any particular downstream user might actually experience. Durez Div. of Occidental Chemical Corp v. OSHA, 906 F.2d 1, 4 (D.C. Cir. 1990); General Carbon Co. v. OSHRC, 860 F.2d 479, 485 (D.C. Cir. 1988).

For these reasons, hazard communication—as opposed to risk communication—“most adequately assures” employee protection from the significant risk of material impairment of health arising from the use of hazardous chemicals in the workplace for purposes of OSHA's authority under section 6(b)(5) of the Act. In addition, HCS is authorized under section 6(b)(7), which requires OSHA to prescribe “labels or other appropriate forms of warning as are necessary to insure that employees are apprised of all hazards to which they are exposed, relevant symptoms and appropriate emergency treatment, and proper conditions and precautions of safe use or exposure.” As noted above, the Benzene case recognizes that the “backstop” provisions of section 6(b)(7) allow OSHA to impose information requirements even before the employee is exposed to the significant risk. In this way, the HCS assures that employers and employees have the information they need to avoid situations of exposure in the work place even before the employee is exposed to a hazardous chemical.

The current proposal makes no conceptual or theoretical change in this approach. It still imposes the same general requirements: Hazard identification, labeling, safety data sheets, a written hazard communication program, and employee training. OSHA's determination that inadequate communication about hazardous chemicals constitutes a significant risk supports the incorporation of the GHS into the HCS, just as it supported the promulgation of the original HCS and its subsequent modifications. Further, the data discussed in parts V and VII of this preamble show that the significant risk continues to exist even under the current standard. OSHA estimates that over 40 million employees are potentially exposed to hazardous chemicals. BLS data show that in 2007, there were approximately 54,000 illnesses related to hazardous chemical exposure and 125 chemically-related fatalities. These new statistics probably represent only a small portion of the illnesses experienced by exposed employees because many illnesses are not reported as being related to workplace exposures, due to long latency periods, and other factors. For all the reasons detailed in Section V, the agency believes that adoption of the GHS will improve communication of the hazards associated with the use of chemicals, and reduce significant risk.

B. Section 6(b)(7) Authority. With respect to labels and employee warnings, the last sentence of section 6(b)(7) provides that:

The Secretary, in consultation with the Secretary of Health and Human Services, may by rule promulgated pursuant to section 553 of title 4, United States Code, make appropriate modifications in the foregoing requirements relating to the use of labels or other forms of warning, monitoring or measuring, and medical examinations as may be warranted by experience, information, or medical or technological developments acquired subsequent to the promulgation of the relevant standard.

29 U.S.C. 655(b)(7).

OSHA has used the authority of section 6(b)(7) in the past to revise its standards. See, e.g., Standards Improvement Project—Phase II, 70 FR 1112 (January 5, 2005); Standards Improvement (Miscellaneous Changes) for General Industry and Construction Standards, 63 FR 33450, 33458 (June 18, 1998). For example, it used this authority to revise the inorganic arsenic and coke oven emissions standards to eliminate the requirement of sputum cytology testing and to reduce the required frequency of mandatory chest x-rays from semi-annual to annual. 63 FR 33458. OSHA justified these changes on the grounds that studies reported after the promulgation of the relevant standards showed that sputum-cytology did not improve employee survival rates and the survival rates for semi-annual x-rays were not higher than annual exams. 63 FR 33458-59. In addition, OSHA has used its section 6(b)(7) authority to authorize new respirator fit protocols under its respiratory protection standard. 69 FR 46986 (August 4, 2004); see generally 29 CFR 1910.134 App. A, Pt. II.

OSHA's proposal to revise the HCS fits well within the authority granted by the last sentence of § 6(b)(7). Adoption of GHS provisions would constitute a “modification[]” of the HCS regarding “the use of labels or other forms of employee warning.” For the reasons summarized above and explained more fully elsewhere in this preamble, OSHA believes that the adoption of GHS to be “appropriate” based on “experience, information, or medical or technological developments acquired subsequent to the promulgation of the relevant standard.” The formulation of GHS may also be considered a “technological development” that has occurred since the promulgation of the original standard in 1983. GHS was negotiated and drafted through the involvement of labor, industry, and governmental agencies, and thus represents the collective experience and information on hazard communication gathered by the participants in these sectors over the last several decades. See Part III above and 71 FR 53618-19. Indeed, OSHA noted the possibility of a future internationally harmonized standard in the preamble accompanying the original rule. 48 FR 53287.

The last sentence of section 6(b)(7) also requires consultation with the Secretary of Health and Human Services. OSHA briefed NIOSH on this proposal as a part of the October 2008 OSHA-NIOSH Issues Exchange meeting, which was attended by NIOSH's Acting Director, and NIOSH expressed its support. OSHA has also briefed NIOSH on the GHS in previous Issues Exchange meetings. In addition, NIOSH has actively supported the GHS during its development and has been involved in the development of control banding, international chemical safety cards, and employee training for the GHS. NIOSH has submitted a comment supporting OSHA's proposal, (Ex. 2-46-1), and reviewed a draft of both this NPRM and the ANPR before it was published. NIOSH has stated that it

supports OSHA in its proposal to update the HCS and to address the changes in hazard criteria, to include all 16 physical hazard criteria, and to adopt the specific labeling requirements and the safety data sheet (SDS) order of information in the Globally Harmonized System of Classification and Labelling of Chemicals.

(Document ID # 0082) These consultations coupled with OSHA's on-going relationship with NIOSH are more than sufficient to satisfy the requirement. For all the reasons set forth above, revision of the HCS through adoption of the GHS as proposed by OSHA is authorized by section 6(b)(7) of the OSH Act, 29 U.S.C. 655(b)(7).

C. Section 6(b)(5) Authority. OSHA also has authority to adopt the proposal under section 6(b)(5) of the Act, 29 U.S.C. § 655(b)(5). As noted above, section 6(b) explicitly allows OSHA to “modify” standards, and adoption of the GHS is justified because it “most adequately assures” employee protection for purposes of section 6(b)(5) for the reasons detailed in part V of this preamble. Section 6(b)(5) also requires a finding that the proposed standard is feasible, which means “capable of being done, executed or effected.”Cotton Dust, 452 U.S. at 508-09.

Feasibility has two aspects, economic and technological. United Steelworkers of America v. Marshall, 647 F.2d 1189, 1264 (D.C. Cir. 1981) (“Lead I”). A standard is technologically feasible if the protective measures it requires already exist, can be brought into existence with available technology, or can be created with technology that can reasonably be expected to be developed . See Lead I, 647 F.2d at 1272. A standard is economically feasible if industry can absorb or pass on the cost of compliance without threatening its longer term profitability or competitive structure. See Cotton Dust, 452 U.S. at 530 n.55; Lead I, 647 F.2d at 1265.

In addressing feasibility in the 1994 HCS revisions, OSHA found that:

The feasibility question raised by the HCS is not difficult to resolve. This standard does not relate to activities on the frontiers of scientific knowledge; the requirements are not the sorts of obligations that approach the limits of feasibility. Associated Builders Contractors, 862 F.2d at 68. The record on which the original and expanded HCS's were based did not contain credible evidence that the HCS would be technologically or economically infeasible for any industrial sector, id., and there was substantial evidence of feasibility, 52 FR 31855-58.

59 FR 6133. OSHA has repeatedly found that the requirements of the HCS are technologically feasible. See 52 FR 31855-57; 59 FR 6133. While the GHS modifications to HCS impose more specific requirements for hazard classification, labeling, and safety data sheets, employers may use the same methods to meet these requirements as they are already utilizing to comply with the requirements of HCS.

The most important resource employers will need to comply with the GHS modifications to HCS is technical expertise in hazard classification and the communication of those hazards. OSHA found that such expertise was already available in promulgating the initial HCS rule in 1983. 48 FR 53296-99. OSHA believes that the availability of professionals with this expertise has only increased in the intervening time. At least one professional organization provides training in hazard communication to professionals and businesses. (Document ID #s 0021 and 0145.) Through OSHA's Alliance with the Society for Chemical Hazard Communication, training to small businesses in the requirements of hazard communication and information about the GHS modifications has been made available. See http://www.osha.gov/dcsp/alliances/schc/schc.html. NIOSH is preparing a program for employers to use in training their employees in the new labeling scheme. (Document ID # 0082.) OSHA received numerous comments in response to its September 12, 2006 ANPR discussing the professionals and tools (both manual and electronic) that employers have available to comply with current hazard communication requirements. (See, e.g., Document ID #s 0042, 0046, 0050, 0053, 0072, 0077, 0015, 0024, 0026, 0036, 0038, 0107, 0108, 0116, 0123, 0128, 0141, 0144, 0145, 0154, 0155, and 0163.) The Agency has been engaged on several fronts to facilitate the transition from the current standard to the GHS modifications, if ultimately adopted. For instance, the United Nations Institute for Training and Research (UNITAR) is developing basic and more advanced training courses for the GHS, and OSHA has been involved with and committed resources to this effort. NIOSH's comment also discussed the development of the WHO/IPCS International Chemical Safety Cards, which includes the GHS pictograms and signal words. (Document ID # 0082.) OSHA believes that adopting the GHS modifications as proposed poses no technological feasibility issues.

Likewise, for the reasons more fully discussed in the Preliminary Regulatory Analysis, OSHA believes that there is nothing about the adoption of GHS that will pose economic feasibility issues. Again, OSHA has found that the implementation of HCS in the first instance would have no such effect. See 52 FR 31855-57; 59 FR 6133. Most commenters agreed that, once conversion to the new system is completed, compliance with the GHS-modified HCS will not be more expensive than compliance with the current HCS. (Document ID #s 0046, 0047, 0080, 0103, 0104, 0105, 0179, 0119, 0123, 0129, 0135, 0139, 0145, 0147, and 0163.) While industry will incur the cost of converting to the new system, OSHA does not believe that this cost is so substantial as to threaten long term profitability or the competitive structure of any industry.

Finally, OSHA is not proposing to “delegate[e] power to an international body” through the adoption of the GHS or justifying this proposal as a means to reduce “potential barriers to international trade,” as suggested in the comments. (Document ID #s 0065 and 0026). OSHA recognizes, however, that there are potential benefits to international trade by adopting the GHS, and these are discussed in section VII of this preamble, OSHA is proposing to comply with the OSH Act's mandate to assure as far as possible safe and healthful working conditions in this country by incorporating the GHS's improved hazard communications requirements into the HCS through the process authorized by section 6 of the OSH Act. Adoption of the GHS modifications into the HCS would not place any new obligations on OSHA to comply with the requirements of any foreign or international body.

VII. Preliminary Economic Analysis and Initial Regulatory Flexibility Screening Analysis Back to Top

A. Introduction and Summary

Introduction

OSHA is required by the Occupational Safety and Health (OSH) Act of 1970 to ensure and demonstrate that standards promulgated under the Act are reasonably necessary and appropriate, as well as technologically and economically feasible. Executive Order 12866, the Regulatory Flexibility Act, and the Unfunded Mandates Reform Act also require OSHA to estimate the costs, assess the benefits, and analyze the impacts of certain rules that the Agency promulgates.

Accordingly, OSHA has prepared this Preliminary Economic Analysis (PEA), including an Initial Regulatory Flexibility Screening Analysis (IRFSA), for the proposed modifications to the Hazard Communication Standard (HCS). The OSHA PEA is based largely on research conducted for this purpose by Policy, Planning, and Evaluation, Inc. (PPE), as presented in their report, “Data and Analysis in Support of an Economic Analysis of Proposed Changes to the OSHA Hazard Communication Standard,” prepared under contract to OSHA. The PPE report is available in the public docket for this rulemaking, OSHA-H022K-2006-0062, through www.regulations.gov.

Need for Regulation

Employees in work environments covered by the HCS are exposed to a variety of significant hazards that can and do cause serious injury and death. The HCS serves to assure that both employers and employees are provided needed information about chemical hazards that was not provided by markets in the absence of such a standard. The HCS also facilitates interstate commerce by promoting consistency among Federal and individual State requirements.

The proposed changes would create a uniformity standard for the presentation of risk information and, as such, would serve to improve the efficiency and effectiveness of the existing hazard communication system in the U.S., and to reduce unnecessary barriers to trade. Hazard communication is currently addressed by many different international, national, and State authorities. As described in Section V of the preamble, these existing requirements are not always consistent and often contain different definitions of hazards and varying provisions for what information is required on labels and safety data sheets. Complying with these different rules results in increased costs for employers with hazardous chemicals in their workplace and for chemical manufacturers, distributors, and transporters involved in international trade. In addition to these effects on businesses, the different existing requirements result in workplaces receiving chemicals with varying information, with potential adverse impacts on the safety and health of employees. The proposed revisions to the OSHA HCS would standardize the hazard communication requirements for products used in U.S. workplaces, and thus provide employees with uniform and consistent hazard communication information. Secondarily, because these proposed revisions would harmonize the U.S. system with international norms, they would facilitate international trade.

Affected Industries

The proposal would affect employers and employees in many different industries across the economy. Based on the PPE report, OSHA estimates in Table VII-2 that the HCS covers over five million workplaces in which employees are potentially exposed to hazardous chemicals.

For establishments with employees whose exposures to hazardous chemicals results from their use of the chemical products, the proposed revisions to the HCS would generally involve minor effects, such as familiarization with new warning labels. For establishments producing hazardous chemicals, which are generally part of the chemical manufacturing industry, the revisions to the standard would involve reclassifying chemicals in accordance with the new classification system and revising safety data sheets (SDSs) and labels associated with hazardous chemicals. OSHA has preliminarily judged that SDSs for imported chemicals would normally be produced in the country of origin, and thus would not represent expenses for importers. OSHA welcomes comment on this judgment.

Benefits, Net Benefits, and Cost-Effectiveness

There is ample evidence of the substantial risks of chemical exposure in the workplace. In 2007, according to the Bureau of Labor Statistics, employees suffered an estimated 55,400 illnesses attributable to chemical exposures (BLS, 2008), and some 17,340 chemical-source injuries and illnesses involved days away from work (BLS, 2009). However, as noted in the preamble to the HCS in 1983, BLS estimates probably only reflect a small percentage of occupational illnesses (48 FR 53284) because most occupational illnesses are not reported. The principal reasons are that they are not recognized as being related to workplace exposures and are subject to long latency periods between exposure and the manifestation of disease. The key study of the issue of the number of fatalities from chronic illnesses, not recorded in any way by BLS, is Leigh et al., 1997. That study found that in 1992, there were from 46,900 to 73,700 fatalities from chronic illnesses related to occupational exposures to chemicals. This critical category dwarfs all acute injuries and illnesses due to chemicals recorded by BLS. [1]

Section V of the preamble describes some of the incidents that may have been related to the non-standardized approach to SDSs in the current HCS, including xylene exposure at a hospital when an employee was unable to find critical information on an SDS in an emergency spill situation (Hanson, 2004). As a result, twelve employees required emergency room treatment. Another example is the explosion at a manufacturing plant in Corbin, KY, which resulted in the death of 7 workers and injuries to another 37 workers. A Federal investigation into the explosion concluded that the cause was the inability to effectively identify and respond to the inherent explosive hazards of phenolic resin and specifically referenced the MSDS for phenolic resin dust (U.S. Chemical Safety and Hazard Investigation Board, February 2005). Were the information on SDSs more uniformly formatted and comprehensible, as required under the proposed modifications to HCS, incidents such as those described above would be less likely to occur.

In general, the proposed modifications to the HCS are expected to result in increased safety and health for the affected employees and to reduce the numbers of accidents, fatalities, injuries, and illnesses associated with exposures to hazardous chemicals.

It is difficult to quantify precisely how many injuries, illnesses, and fatalities would be prevented due to the proposed revisions to the HCS. The benefits associated with the existing HCS may indirectly help provide a general sense of the potential magnitude of the benefits of the proposed revisions to the HCS. OSHA preliminarily estimates that if the proposed rule could capture one percent of the benefits estimated for the original 1983 and 1987 HCS rules, the proposed revisions would result in the prevention of 318 non-lost-workday injuries and illnesses, 203 lost-workday injuries and illnesses, 64 chronic illnesses, and 43 fatalities annually. The monetized value of the corresponding reduction in occupational risks among the affected employees is an estimated $266 million on an annualized basis.

The harmonization of hazard classifications, safety data sheet formats, and warning labels for affected chemicals and products would also involve substantial savings to businesses. Fewer different SDSs would have to be produced for affected chemicals, and many SDSs would be able to be produced at lower cost due to harmonization and standardization. The benefits represented by these cost reductions would primarily affect businesses involved in chemical manufacturing. In addition, businesses that purchase or use hazardous chemicals can expect reductions in operating costs as a result of the promulgation and implementation of the proposed modifications.

PPE conducted extensive research on the processes that companies use to classify chemical hazards, to develop SDSs and labels, and to handle, store, and use hazardous chemicals. PPE evaluated how these processes would be affected by the proposed revisions to the HCS and analyzed the potential savings that would be realized as a result of adopting these revisions. Based on PPE's research, OSHA has concluded that the annual cost savings for these companies would be an estimated $585 million.

As an additional benefit, the modification of the HCS by the inclusion of the globally harmonized system (GHS) of classification and labelling of chemicals would be expected to facilitate international trade, increasing competition, increasing export opportunities for U.S. businesses, reducing costs for imported products, and generally expanding the selection of chemicals and products available to U.S. businesses and consumers. As a result of both the direct savings resulting from harmonization and the increased competitiveness, prices for the affected chemicals and products, and the corresponding goods and services using them, would be lowered.

The proposed revisions may also result in reductions in the costs associated with providing training for employees as required by the existing OSHA HCS.

Finally, the proposed GHS modifications to the OSHA HCS would meet the international goals for adoption and implementation of the GHS that were supported by the U.S. government. Implementing GHS in U.S. Federal laws and policies through appropriate legislative and regulatory action was anticipated by the U.S. support of international mandates regarding the GHS in the Intergovernmental Forum on Chemical Safety, the World Summit on Sustainable Development, and the United Nations. It is also consistent with the established goals of the Strategic Approach to International Chemical Management that the U.S. helped to craft (see http://www.chem.unep.ch/saicm/).

Table VII-1 provides a summary of the costs and benefits of the proposed modifications to the OSHA HCS, and it shows the net benefits of the modifications to the standard, which are estimated to be $754 million annually. Because compliance with the proposed standard would result in cost savings that exceed costs, OSHA has not provided estimates of costs per life saved or other metrics of cost-effectiveness. However, it should be noted that the estimated benefits exceed costs by a factor of eight.

BILLING CODE 4510-26-P

BILLING CODE 4510-26-C

Compliance Costs

The estimated compliance costs for the proposed revisions to the HCS represent the additional costs necessary for employers to achieve full compliance. They do not include costs associated with current compliance that has already been achieved with regard to the new requirements; nor do they include costs necessary to achieve compliance with existing requirements, to the extent that some employers may currently not be fully complying with applicable regulatory requirements.

The costs associated with compliance with the proposed revisions to the HCS would generally be incurred by the affected industries as one-time transition costs over the phase-in period of three years. Aside from the transition costs, the ongoing annual compliance costs associated with the proposed revisions to the HCS generally are expected to be the same or lower than under the existing standard.

The compliance costs are expressed as an annualized cost for purposes of assessing the cost-effectiveness of the proposed revisions, in order to be able to compare the economic impact of the rulemaking with other regulatory actions, and to be able to add and track Federal regulatory compliance costs and economic impacts in a consistent manner. Annualized costs also represent a better measure for assessing the longer-term potential impacts of the rulemaking. The annualized cost was calculated by annualizing the one-time costs over a period of 20 years and applying a discount rate of 7 percent, as recommended by the Office of Management and Budget.

The total annualized cost of compliance with the proposed standard is estimated to be about $97 million. The major cost elements associated with the revisions to the standard include the classification of chemical hazards in accordance with the GHS criteria and the corresponding revision of safety data sheets and labels to meet new format and content requirements ($11 million); training for employees to become familiar with new warning symbols and the revised safety data sheet format ($44 million); and management familiarization and other management-related costs as may be necessary ($42 million).

Economic Impacts

To assess the nature and magnitude of the economic impacts associated with compliance with the proposed rule, OSHA developed quantitative estimates of the potential economic impact of the new requirements on entities in each of the affected industry sectors. The estimated compliance costs were compared with industry revenues and profits to provide an assessment of the economic feasibility of complying with the revised standard and an evaluation of the potential economic impacts.

Only the compliance costs were considered for purposes of assessing the potential economic impacts and economic feasibility of the proposed revisions. As described in section D of this PEA, the overall economic impacts associated with this rulemaking are expected to result in significant net benefits to employers, employees, and the economy generally.

As described in greater detail in section G of this PEA, the costs of compliance with the proposed rulemaking are not large in relation to the corresponding annual financial flows associated with each of the affected industry sectors. The estimated costs of compliance represent about 0.0004 percent of revenues and about 0.007 percent of profits, on average, across all entities; compliance costs do not represent more than 0.02 percent of revenues or more than 0.3 percent of profits in any individual affected industry sector.

The economic impact of achieving compliance with the proposal, without considering the associated benefits, is most likely to consist of an extremely small increase in prices of about 0.0004 percent, on average, for affected hazardous chemicals. It is highly unlikely that a price increase of this magnitude would significantly alter the types or amounts of goods and services demanded by the public or any other affected customers or intermediaries. If the compliance costs of the proposal can be substantially recouped with a minimal increase in prices, there may be little or no effect on profits.

In general, for most establishments, it would be very unlikely that none of the compliance costs could be passed along in the form of increased prices. In the event that a price increase of 0.0004 percent were not possible, profits in the affected industries would be reduced by an average of about 0.007 percent.

Given the minimal potential impact on prices or profits in the affected industries, OSHA has preliminarily concluded that compliance with the requirements of the proposed rulemaking would be economically feasible in every affected industry sector.

In addition, based on an analysis of the costs and economic impacts associated with this rulemaking, OSHA preliminarily concludes that the effect of the proposed standard on employment, wages, and economic growth for the United States would be negligible. The effect on international trade is likely to be beneficial and similar to the effect of a small reduction in non-tariff trade barriers.

Initial Regulatory Flexibility Screening Analysis

OSHA has analyzed the potential impact of the proposed rule on small entities, and has prepared an Initial Regulatory Flexibility Screening Analysis (IRFSA) in conjunction with this rulemaking to describe the potential effects on small entities. The IRFSA is included as a part of this PEA in section H.

As a result of the analysis of the potential impact on small entities, OSHA concludes and certifies that the rulemaking would not have a significant impact on a substantial number of small entities. Therefore, an Initial Regulatory Flexibility Analysis (IRFA) is not required for this rulemaking. Nevertheless, OSHA has voluntarily provided the elements of the IRFA as part of the IRFSA presented in Section H. In proceeding with this rulemaking, OSHA will fulfill its requirements under the Regulatory Flexibility Act and under the Small Business Regulatory Enforcement Fairness Act, as applicable, to ensure that no unnecessary burdens are imposed on small businesses.

The remainder of this PEA includes the following sections:

B. Need for Regulation;

C. Profile of Affected Industries;

D. Benefits, Net Benefits, and Cost-Effectiveness;

E. Technological Feasibility;

F. Costs of Compliance;

G. Economic Feasibility and Impacts;

H. Initial Regulatory Flexibility Screening Analysis;

I. Environmental Impacts;

J. Unfunded Mandates Reform Act Analysis;

K. Sensitivity Analysis.

B. Market Failure and the Need for Regulation

Employees in work environments addressed by the HCS are exposed to a variety of significant hazards associated with chemicals used in the workplace that can and do cause serious injury and death. OSHA's HCS was designed to assure that employers and employees are provided the information they need about the chemical hazards in chemical products both to make informed purchases and to provide for safe use. In the existing HCS, OSHA developed a set of requirements for chemical products, to include mandatory classification, labeling, and detailed information provision (in safety data sheets). OSHA believes that the improvements in the proposed rule would make the hazard communication system more worker-protective and more efficient and effective. In addition, the improvements would have the effect of harmonizing hazard communication to facilitate international trade—replacing a plethora of national rules with a single international system.

The proposed standard, through conformance with GHS (as explained in Section IV of the preamble), contains a number of changes to improve the performance of the U.S. hazard communication system:

  • Revised criteria for more consistent classification of chemical hazards;
  • Standardized signal words, pictograms, hazard statements, and precautionary statements on labels; and
  • A standardized format for SDSs.

In short, GHS is a “uniformity standard” for the presentation of hazard information (Hemenway, 1975, p. 8). And much like other uniformity standards, such as driving on the right side of the road (in the U.S.), screw threads for fire hose connectors, “handshake” protocols for communication between computers, and, for that matter, language, GHS would provide significant efficiencies and economies. [2] In the case of GHS, manufacturers would be able to produce SDSs at lower cost, and users of SDSs would be able to more fully and quickly utilize the information contained in the SDSs, thereby reducing costs and, more importantly, better protect workers against chemical hazards. [3]

Since publication of the existing HCS, there has been some movement by industry toward standardization, consistent with the proposed revisions. However, OSHA does not believe that full and comprehensive standardization, as required under the proposed revisions, or that the goal of harmonizing the U.S. system with the international one could be achieved voluntarily in the absence of regulation.

First, in a basic sense, GHS cannot simply be implemented by the market. Some aspects of GHS, such as the reorganization of SDSs, would be allowed under the existing OSHA standard, but other aspects, such as the classifications system, would not be. Use of differing classification criteria would lead to label warnings that are not consistent with current HCS requirements in some situations. Thus, at a minimum, OSHA would need to modify HCS to allow the use of GHS in the U.S. OSHA cannot simply provide a compliance interpretation that labels and safety data sheets prepared in accordance with the GHS meet the HCS requirements because the requirements of a standard cannot be changed through a compliance interpretation. While there is considerable overlap between the HCS and the GHS in terms of coverage, there are differences in the criteria used to classify both substances and mixtures that will result in different hazards being covered in some situations. This is particularly true in the area of acute toxicity, where OSHA is covering more substances under the modified rule than the current HCS, but potentially fewer mixtures. [4]

Second, it is important to understand that while the costs of creating SDSs and labels under GHS are borne directly by the chemical producers, the bulk of the benefits of adopting GHS accrue to the users. The set of all users includes employers who are direct customers of a chemical manufacturer, employees who use or are exposed to workplace chemicals, and emergency responders, who typically have no market relationship with the producers of the chemical. Even if one thought that market forces might assure the socially optimal approach to SDSs between manufacturers of chemicals and their customers, there are limited market forces at work between the chemical manufacturer and these two other sets of users—the employees and the emergency response community. Therefore, the presence of positive GHS externalities would prevent the private market, without regulation, from achieving the socially optimal adoption of GHS.

OSHA does anticipate that there will be some increased market pressure to comply with GHS that will affect some firms that may think that they have no need to switch to the GHS system because they do not ship their products internationally. Many small firms do not realize the extent to which they are involved in international trade. There are probably few companies who have products that are never involved in international trade, or who never import chemical products and need hazard communication information for them. Many chemical producers ship their products to distributors and are unaware of where their products are ultimately used. OSHA can envision a likely scenario in which these distributors provide pressure to their suppliers to become GHS-compliant. Further, small companies sell products to larger companies. The larger companies may use those products to prepare goods that are exported. These larger companies might also be expected to pressure their small firm suppliers to be GHS-compliant. Nevertheless, such an approach would surely involve a long transition period, with attendant losses in worker protection and production efficiencies, and it is doubtful that market pressure alone would achieve full compliance.

The changes made by GHS will involve costs for all parties. Producers of chemicals will incur substantial costs but will also achieve benefits—in part because they themselves benefit as both producers and users, and in part, as a result of foreign trade benefits that OSHA has not quantified. Some producers will not see these types of trade benefits if they do not engage in exporting chemicals. However, many small companies are currently prevented from engaging in international trade because of the substantial burdens of complying with many different countries' requirements. International harmonization of hazard communication requirements would enable these small companies to become involved in international trade if they so desire.

Of more significance to the concerns of the OSH Act, the changes also provide substantial benefits to users, including:

  • Fewer illnesses, injuries, fatalities, and accidents due to a more consistent, comprehensible, and clearer system that does not require English literacy to obtain some minimal hazard information;
  • Greater ease of use of SDSs; and
  • Reduced training requirements for workers due to a clearer and more uniform system.

Because many of these benefits require uniformity, and the benefits are dispersed throughout a network of producers and users, only some of which have direct market relationships with each other, OSHA believes that only a single, uniform standard can achieve the full net benefits available to a hazard communications system.

C. Profile of Affected Industries

The proposed revisions to the HCS would affect establishments in a variety of different industries in which employees are exposed to hazardous chemicals or in which hazardous chemicals are produced. Every workplace in OSHA's jurisdiction in which employees are exposed to hazardous chemicals is covered by the HCS and is required to have a hazard communication program.

The proposed revisions to the HCS are not anticipated to either increase or decrease the scope of affected industries or establishments. The proposed revisions define and revise specific classifications and categories of hazards, but the scope of the requirements under which a chemical, substance, or mixture becomes subject to the requirements of the standard are not substantially different from the current HCS. Therefore, the proposed revisions should have little or no effect on whether an entire establishment falls within the scope of the standard. OSHA requests comments from the public regarding this preliminary determination.

For establishments with employees exposed to hazardous chemicals, the proposed revisions to the HCS would generally involve management becoming familiar with and employees receiving training on the new warning labels and the new format of the SDSs. For establishments producing or importing hazardous chemicals, generally as part of the chemical manufacturing industry, the revisions to the standard would involve reclassifying chemicals in accordance with the new classification system and revising safety data sheets and labels associated with hazardous chemicals.

OSHA's estimates of the number of employees covered by the standard are based on the preliminary determination that all production employees in manufacturing would be covered, and that, in addition, employees in other industries working in any of the occupations specified in the PPE report would also be exposed to hazardous chemicals.

Table VII-2 provides an overview of the industries and estimated numbers of employees potentially affected by the HCS. OSHA welcomes additional information and data that may help improve the accuracy of these estimates.

The industries and establishments affected by the proposed revisions can be divided into two categories. The first category contains establishments that are required to produce labels and SDSs; the second category contains establishments that do not produce labels or SDSs but are required to provide employee access to labels and SDSs, supplied by others, for the chemicals to which their employees may be exposed in the workplace. As noted, OSHA has preliminarily judged that SDSs for imported chemicals would normally be produced in the country of origin, and thus would not represent expenses for importers or other US firms.

As shown in Table VII-2, approximately 75,000 firms, in over 90,000 establishments, create hazardous chemicals (i.e., products, substances, or mixtures) for which a label and an SDS are required in accordance with the OSHA HCS. Approximately 880,000 SDSs and corresponding container labels would be potentially affected by the proposed revisions to the HCS. OSHA estimates that the adoption of GHS through this proposal would not significantly change the numbers of labels and SDSs produced. OSHA welcomes comment on this issue.

In many instances, firms may be already producing several different versions of SDSs and labels for the same product to satisfy different regulatory requirements in different jurisdictions, including SDSs and labels consistent with GHS criteria. For these products, the proposed revisions to the OSHA HCS would be satisfied relatively easily and may result in a reduction in overall compliance costs by reducing the number of different labels and SDSs needed for each affected product.

BILLING CODE 4510-26-P

BILLING CODE 4510-26-C

OSHA requests comments from the public regarding these preliminary conclusions and requests information on the number and type of labels and SDSs that would be affected or produced as a result of this proposal.

The second category of industries and establishments affected by the proposed revisions contains those that do not produce SDSs but are required to provide their employees with access to SDSs supplied by others as part of a hazard communication program covering chemicals to which employees may be exposed in the workplace. The effects on these establishments would generally involve promoting employee awareness of and management familiarization with the revisions to SDSs and labels.

As shown in Table VII-2, an estimated 38 million employees are potentially exposed to hazardous chemicals in these workplaces and are covered by the OSHA HCS. Including employees working in establishments that produce SDSs, a total of 41 million employees would potentially need to become familiar with the proposed revisions to SDSs and labels. As also shown in Table VII-2, OSHA estimates that there are over five million workplaces where employees may be potentially exposed to hazardous chemicals. OSHA requests comments and information from the public regarding these estimates.

D. Benefits, Net Benefits, and Cost-Effectiveness

OSHA estimates that the promulgation of the proposed revisions would result in substantial benefits from a variety of sources. OSHA's estimates of the benefits include improvements in occupational safety and health and a corresponding reduction in the annual number of injuries, illnesses, and fatalities sustained by employees from exposure to hazardous chemicals; reductions in costs for producers of hazardous chemicals; increased efficiencies in the handling and use of hazardous chemicals; and other benefits as described in this section. OSHA requests comments and information from the public regarding the nature and extent of any benefits that may be associated with the proposed revisions.

OSHA expects the proposed revisions to the HCS would result in an increased degree of safety and health for the affected employees and to reduce the number of accidents, fatalities, injuries, and illnesses associated with exposure to hazardous chemicals.

As explained in detail in Section V of the preamble, the design of GHS was based on years of extensive research that demonstrated the effectiveness of pictograms, specific signal words, and a standardized format. As a result of this research, OSHA is confident that the GHS revisions to the HCS standard for labeling and safety data sheets would enable employees exposed to workplace chemicals to more quickly obtain and more easily understand information about the hazards associated with those chemicals. Warning labels on products covered by the standard, which provide an immediate visual reminder of the chemical hazards involved, would be made more intuitive, self-explanatory, and logical, and the nature and extent of any associated hazards would be more readily understood as a result of the training required under the proposal. Relatedly, the revisions are expected to improve the use of appropriate exposure controls and work practices that can reduce the safety and health risks associated with exposure to hazardous chemicals.

In addition, the standardized format of the safety data sheets would enable critical information to be accessed more easily and quickly during emergencies. This can reduce the risk of injury, illness, and death to exposed employees and to rescue personnel and can reduce property damage.

It is difficult to quantify precisely how many injuries, illnesses, and fatalities would be prevented due to the proposed revisions to the HCS. The benefits associated with the existing HCS may help provide a general sense of the potential magnitude of the benefits of the proposed revisions to the HCS. A discussion and analysis of the benefits that would result from the implementation of the existing OSHA HCS were included as part of the rulemaking process for the promulgation of the existing standard in the 1980s.

The existing HCS was originally promulgated in two parts. First, a final rule covering the manufacturing industry was published in the Federal Register in 1983 (48 FR 53280, November 25, 1983); a second final rule covering other general industries, maritime industries, construction industries, and agricultural industries was published in the Federal Register in 1987 (52 FR 31852, August 24, 1987).

For both of these final rules, OSHA conducted research specifically regarding the benefits that could be expected from the promulgation of these standards, as described in the preambles to the final rules. In addition, through the rulemaking process, OSHA evaluated the best available evidence, including the data and comments submitted by the public.

The information, data sources, analyses, and findings related to the estimation of the benefits associated with the standards are included in the public records for the rulemakings. The complete rulemaking records for these standards can be found in OSHA public dockets H-022B and H-022D.

The estimated benefits associated with the Hazard Communication Standards were published in the Federal Register with the promulgation of the final standards (48 FR 53329, November 25, 1983 and 52 FR 31872, August 24, 1987). OSHA estimated that compliance with the various Hazard Communication Standards would produce annual benefits that would include the prevention of 31,841 non-lost-workday injuries and illnesses, 20,263 lost-workday injuries and illnesses, 6,410 chronic illnesses, and 4,260 fatalities.

Using a willingness-to-pay approach for valuing these benefits, OSHA determined that the annual safety and health benefits would be over $18.2 billion annually, expressed in 1985 dollars. According to the inflation calculator provided by the Bureau of Labor Statistics, the buying power of $18.2 billion in 1985 is equivalent to the buying power of about $35.3 billion in 2007 after adjusting for inflation of 94 percent over the period. [5]

Based on the material presented in this preamble, OSHA expects that the proposed revisions to the HCS would result in incremental improvements in employee health and safety above that already achieved under the existing HCS. For purposes of this proposal, OSHA has selected an estimate of 1 percent of the health and safety benefits due to the existing HCS as the benefits that could be attributed to compliance with the proposed revisions. It is conceivable that actual benefits might be somewhat lower, but because GHS is expected to result, in some situations, in more timely and appropriate treatment of exposed workers, OSHA believes actual benefits may be larger, perhaps several times larger. [6] [7]

If the 1 percent estimate is correct, then once all requirements take effect, they would result in the prevention of 318 non-lost-workday injuries and illnesses, 203 lost-workday injuries and illnesses, 64 chronic illnesses, and 43 fatalities annually. The monetized value of these health and safety benefits is an estimated $353 million annually.

In order to obtain a sense of how realistic these estimated safety and health benefits are in light of the current level of occupational injuries, illnesses, and fatalities that are chemically-related, OSHA reviewed relevant BLS data for the periods 1992-2007. OSHA's examination of these data shows a 42 percent decline in chemically-related acute injuries and illnesses over the period, but both remain significant problems—55,400 chemically-related illnesses and 125 chemically related-fatalities in 2007. However these readily measurable reported acute illnesses and fatalities are dwarfed by chronic illnesses and fatalities. For chronic illness fatalities, there is little information available, and certainly no annual time series data. The most recent estimate is that there were 46,900 to 73,700 fatalities due to occupational illnesses in 1992 (Leigh et al., 1997). OSHA believes these more recent data from 1992-2007 show that it is plausible that HCS has had a desirable effect on chemically-related illnesses and injuries, but there remains a very significant role for further and better hazard information, as would be provided by GHS.

OSHA requests information and data from the public that could assist the agency in more accurately determining the safety and health benefits associated with the proposed revisions.

The annual benefits associated with the proposed revisions to the OSHA HCS would generally begin after full implementation of the changes and associated employee training. The phase-in period is expected to take about three years. Thus, in order to calculate the estimated annualized benefits over a twenty-year period associated with this proposed rule in a manner that would be comparable to the corresponding annualized costs, the delay in the realization of the benefits was incorporated into the calculation. Using a discount rate of 7 percent, the annual benefits beginning three years after the effective date of the revisions were multiplied by 0.7523 to calculate the annualized benefits over a twenty-year period beginning with the effective date of the final rule. [8] Thus, the annualized monetized benefit associated with the reduction in safety and health risks attributable to the proposed revisions is an estimated $266 million.

Other substantial benefits, in addition to the improved occupational safety and health of affected employees, are also expected to result from this rulemaking, as discussed in the following paragraphs.

The harmonization of hazard classifications, safety data sheet formats, and warning labels for affected chemicals and products would yield substantial savings to the businesses involved in these activities. Fewer different SDSs would have to be produced for affected chemicals, and many SDSs would be able to be produced at lower cost due to harmonization and standardization. The benefits represented by these cost reductions would primarily affect businesses involved in chemical manufacturing.

In addition, reductions in operating costs are also expected as a result of the promulgation of the proposed revisions for many businesses that purchase or use hazardous chemicals. The current non-uniformity of SDSs and labels received by establishments in practically all industries requires employees and managers in numerous positions to spend additional time on a daily basis to ascertain the appropriate way to handle and store the hazardous chemicals in their workplace. Under the revised standard, the presence of uniform and consistent information would help employers and employees to make decisions more efficiently and save substantial time.

PPE conducted extensive research on the processes that companies use to classify chemical hazards, to develop SDSs and labels, and to handle, store, and use hazardous chemicals. PPE evaluated how these processes would be affected by the proposed revisions to the HCS and analyzed the potential savings that would be realized as a result of adopting these revisions.

Based on the PPE report, OSHA developed estimates of the cost reductions that the affected companies would expect to obtain as a result of the proposed revisions to the OSHA HCS. Among the various benefits expected to be realized as a result of the implementation of the proposed revisions, as described in this section, OSHA quantified two general categories of cost savings. First, OSHA estimated the number of hours that each industry would save by improving the efficiency and productivity of personnel who use SDSs in performing their job functions. OSHA estimated that the amount of time spent during affected activities in the manufacturing sector could be reduced by 3 percent for health and safety supervisors and by 15 percent for logistics personnel specializing in handling hazardous chemicals. [9] OSHA further estimated that this time reduction, and the associated cost savings, would apply to about 7,000 health and safety supervisors and 52,000 logistics personnel in the manufacturing sector and would yield annualized benefits of approximately $569 million. [10] Similar potential time and cost savings as a result of the proposed revisions to the OSHA HCS were not quantified for the non-manufacturing sectors.

Second, OSHA estimated that, for the manufacturing sectors, the costs associated with the creation and revision of SDSs in future years would be reduced by the proposed revisions. The creation and revision of individual SDSs would be less burdensome, and, in addition, fewer different versions of SDSs would need to be produced for affected chemicals and products. OSHA estimated that, depending on firm size, the combination of these two effects would result in annual savings equivalent to between 2.5 and 4 hours of a professional's time per existing SDS and a total annualized savings of $16 million. [11]

Combining the improved productivity of personnel who use SDSs and the improved efficiency of those who revise SDSs and labels, OSHA concluded that the annual cost savings for companies in the manufacturing sector would be an estimated $585 million.

A secondary benefit of the adoption of GHS is that it would facilitate international trade, increasing competition, increasing export opportunities for U.S. businesses, reducing costs for imported products, and generally expanding the selection of chemicals and products available to U.S. businesses and consumers. As a result of the direct savings resulting from the harmonization and the associated increase in international competition, prices for the affected chemicals and products, and the corresponding goods and services using them, should decline, although perhaps only by a small amount.

The proposed revisions may also result in reductions in the costs associated with providing training for employees as required by the existing OSHA HCS. Companies would save considerable time and effort in training new employees in the future. The potential savings would be attributable in part to reducing or eliminating the need to explain the different types of formats used to convey hazard information and the different types of information included in the contents of SDSs and labels.

Finally, the proposed GHS modifications to the OSHA HCS would meet the international goals for adoption and implementation of the GHS that were supported by the U.S. government. Implementing GHS in U.S. Federal laws and policies through appropriate legislative and regulatory action was anticipated by the U.S. support of international mandates regarding the GHS in the Intergovernmental Forum on Chemical Safety, the World Summit on Sustainable Development, and the United Nations. It is also consistent with the established goals of the Strategic Approach to International Chemical Management that the U.S. helped to craft.

Table VII-1 provides a summary of the costs and benefits of the proposed revisions to the OSHA HCS, and it shows the net benefits and cost-effectiveness of the revisions to the standard. Net monetized benefits are estimated to be $754 million annually. The cost-effectiveness of the standard can be expressed as more than eight dollars of benefits for every dollar of cost.

Some qualitative evidence of the cost-effectiveness of the standard was provided by comments submitted in response to the Advance Notice for Proposed Rulemaking (ANPR) published by OSHA in the Federal Register on September 12, 2006 (71 FR 53617). There was widespread (but not unanimous) support among the commenters for the adoption of GHS in the United States. This included commenters who provided some of the largest estimates of the costs of the proposed revisions. (Document IDs # 0032 and # 0050). [12]

E. Technological Feasibility

In accordance with the OSH Act, OSHA is required to demonstrate that occupational safety and health standards promulgated by the Agency are technologically feasible. In fulfillment of this requirement, OSHA has reviewed the requirements that would be imposed by the proposal, and has assessed their technological feasibility. As a result of this review, OSHA has determined that compliance with the requirements of the proposal is technologically feasible for all affected industries. OSHA requests comments and information from the public with regard to this preliminary determination.

The proposal would require employers producing chemicals to reclassify chemicals in accordance with the new classification criteria and revise safety data sheets and labels associated with hazardous chemicals. Compliance with these requirements is not expected to involve any technological obstacles.

The proposal would also require employers whose workplaces involve potential exposure to hazardous chemicals to train employees on the relevant aspects of the revised approach to hazard communication. Affected employees would need additional training to explain the new labels and safety data sheets. Compliance with these requirements is not expected to involve any technological obstacles.

Compliance with all of the proposed requirements can be achieved with readily and widely available technologies. Businesses in the affected industries have long been required to be in compliance with the existing HCS which includes similar requirements. The revised HCS would simply require modifying the labels and SDSs for hazardous chemicals and adding some training to ensure employee familiarization with the changes made. Therefore, there are no new technologies required for compliance with the modifications. In addition, some businesses in the affected industries have already implemented many of the requirements of the proposed standard to varying degrees. OSHA believes that there are no technological constraints associated with compliance with any of the proposed requirements, and welcomes comments regarding this conclusion.

F. Costs of Compliance

Introduction

This section presents the estimated costs of compliance for the proposed revisions to the OSHA HCS. The estimated costs of compliance represent the additional costs necessary for employers to achieve full compliance. They do not include costs associated with current compliance with the new requirements.

The compliance costs associated with the proposal generally consist of the one-time transition costs to adopt the modified criteria for classifications and formats as required under the new system. Ongoing annual costs associated with compliance with the existing OSHA HCS are not expected to increase. As discussed in the benefits section, the adoption of the new system is expected to reduce some of the ongoing costs associated with compliance with the HCS after the completion of the transition period.

The costs of compliance with the proposed revisions consist of three main categories: the cost of reclassification and revision of SDSs and labels, the cost of training employees, and the cost of management familiarization and other management costs associated with the administration of hazard communication programs.

The estimated compliance costs associated with the proposed revisions are based on a preliminary determination that the revisions would not significantly change the number of chemicals or products for which an SDS will be required, which also means that there will be no change in the number of establishments required to implement a hazard communication program. OSHA requests comments and information from the public regarding this preliminary determination.

Other than the direct costs of reclassification and relabeling, the estimated compliance costs do not include any further costs or impacts that may result from the reclassification or relabeling of chemicals and products already subject to the HCS, such as possible changes in production or demand for products. Theoretically, such impacts, if any, with regard to possible changes in the uses and applications of affected chemicals, could be positive as well as negative. OSHA has preliminarily determined that such effects, if any, will not be significant, and requests comments and information from the public regarding this determination.

In addition to the proposed revisions to the HCS, the proposed rulemaking also includes related proposed revisions to other OSHA standards. The revisions to the other standards generally ensure that all OSHA requirements related to hazard communication remain consistent with each other and become consistent with the GHS. OSHA has preliminarily determined that the proposed revisions to the other standards would not impose significant costs beyond those reflected in the preliminary compliance cost estimates for this rulemaking, and requests comments and information from the public regarding this determination.

In order to have compliance costs presented on a consistent and comparable basis across various regulatory activities, the costs of compliance for this proposed rule are expressed in annualized terms. Annualized costs represent the more appropriate measure for assessing the longer-term potential impacts of the rulemaking. The estimated annualized cost of compliance is also provided for purposes of comparing compliance costs and cost-effectiveness across diverse regulations with a consistent metric. In addition, annualized costs are often used for accounting purposes to assess the cumulative costs of regulations on the economy or specific parts of the economy across different regulatory programs or across years. Annualized costs also permit costs and benefits to be presented in a comparable manner. The annualized cost was calculated by annualizing the one-time transition costs over a period of 20 years and applying a discount rate of 7 percent.

Table VII-3 shows the estimated annualized compliance cost by cost category and by industry sector. As shown in Table VII-3, the total annualized cost of compliance with the proposed rulemaking is estimated to be about $97 million. Of this amount, the cost of chemical hazard reclassification and revision of SDSs and labels is an estimated $11 million, the cost of training employees is an estimated $44 million, and the cost of management familiarization and other management costs is an estimated $42 million.

As shown in Table VII-3, most of the compliance cost associated with chemical hazard reclassification and revision of SDSs and labels would be borne by the chemical manufacturing industry. Table VII-3 also shows that compliance costs are spread across all industries in the U.S. economy subject to OSHA jurisdiction, reflecting the fact that employee exposures to hazardous chemicals occur in almost every industry sector.

OSHA expects that the compliance costs would be incurred over a period of three years, as the proposal would incorporate a three-year transition period into the compliance schedule for the standard. Specifically, for purposes of estimating the annualized compliance costs, OSHA assumed that the compliance costs associated with employee training would be incurred in the two-year period following the effective date of the final standard, and that other compliance costs would be incurred in the three-year period following the effective date of the final standard.

BILLING CODE 4510-26-P

BILLING CODE 4510-26-C

In order to make the compliance cost estimates comparable with the corresponding benefits estimates, the expected timing of these costs was taken into account. A seven percent discount rate was applied to costs incurred in future years to calculate the present value of these costs for the base year in which the standard becomes effective, and the same discount rate was then applied to the total present value costs, over a 20-year period, to calculate the $97 million annualized costs.

In the appendix to this cost section, Table VII-4 shows, by industry and by cost element, total non-annualized (non-discounted) compliance costs of about $1.1 billion estimated to be incurred during the three-year phase-in of the proposed revisions.

Estimation of Compliance Costs

The remainder of this section explains how the compliance costs were calculated by describing the data and methodology used to estimate each of the major cost elements. A more complete and detailed description of the estimation of compliance costs can be found in the PPE report.

The major elements of the proposed revisions that involve compliance costs include (1) the classification of chemicals in accordance with the proposed criteria and the revisions to the safety data sheets and labels corresponding to the affected hazardous chemicals; (2) incremental training for employees already trained under the existing OSHA hazard communication programs to ensure their familiarization with the new formats, information, and symbols that would be introduced into the workplace as a result of the proposed revisions; and in addition, (3) even though it is not directly a result of any specific requirement included in the proposed revisions, the cost for managers and administrators of hazard communication programs to become familiar with the revisions to the standard and to manage, update, and revise their programs as may be necessary to ensure compliance with the revised standard.

The estimated compliance costs presented in this analysis of the proposed revisions to the HCS are largely based on research conducted by PPE. PPE performed this research under contract to the Department of Labor specifically for the purpose of developing estimates of compliance costs for, and assessing the potential impacts that may be associated with, possible revisions that may be made to the OSHA HCS in order to implement the GHS.

The estimated costs of compliance with many of the provisions of the proposed standard involve wages paid for the labor hours required to fulfill the requirements. In some cases, compliance could be achieved by purchasing services or products in lieu of paying employees directly. The estimated compliance costs are intended to capture the resources required for compliance, regardless of how individual establishments may choose to achieve compliance.

Costs Associated With Chemical Classifications and Revisions to Safety Data Sheets and Labels

The proposed revisions to the OSHA HCS would continue to require firms that sell hazardous chemicals to employers to provide information about the associated hazards. Information is required to be presented in a safety data sheet (SDS) in the format specified in the revised standard, and some information is also required to be presented on product labels.

The existing OSHA HCS already requires information about hazardous chemicals to be provided in SDSs and on labels. In addition, under the existing standard, SDSs are to be revised after a manufacturer or employer becomes aware of any significant new information about the hazards of a chemical.

The proposed revisions to the standard would require chemicals to be classified into the appropriate hazard classes and categories based on the information about the chemicals that the manufacturers currently have. This information would have been assembled for purposes of conducting a hazard determination under the current HCS. In addition, the current HCS requires chemical manufacturers and importers to remain aware of developments regarding the hazards of the chemicals they produce or import in order to update the labels and SDSs for the chemicals in a timely manner. The classification of the chemicals into the hazard classes and categories under the revised provisions would not require any additional testing, studies, or research to be conducted. Manufacturers would be able to rely on the information they already have in determining how to properly classify their chemicals.

Generally, chemical manufacturers and importers periodically review, revise, and update SDSs and labels. Changes are made as necessary as information regarding specific hazards develops, new information about protective measures is ascertained, or changes are made to product information and marketing materials. Labels and SDSs must also be produced or modified when products are introduced or changed. Therefore, there is a regular cycle of change for these documents for a variety of reasons. The proposed revisions may require a more extensive change than would normally occur, but the phase-in period is such that the chemical manufacturers and importers can take advantage of the normal cycle of change to phase in the revisions for all their products over a reasonable time period. This should have less impact on normal operations than a short time period that would require all SDSs and labels to be revised at the same time.

The transition period that would be allowed by the delayed effective date for the requirement to adopt the new format should help ensure that the transition can be completed in conjunction with revisions and updates that would normally be expected to occur even without the implementation of the proposed revisions. In addition, the format required by the proposed revisions for SDSs is consistent with the format already adopted by the American National Standards Institute (ANSI) and therefore has already been implemented by many of the affected businesses.

Based on the PPE report, OSHA developed estimates of the costs that would be associated with the classification of chemicals in accordance with the proposed criteria and with the revisions to the corresponding SDSs and labels for those chemicals. The estimated compliance costs represent the incremental costs that would need to be incurred to achieve compliance with the proposed revisions; these estimated costs would be in addition to the costs that would already be incurred to continue to remain in compliance with applicable requirements of the existing HCS.

The proposed revisions would allow for a transition period of three years following the publication of a final rule. During this period, even in the absence of any pertinent OSHA rulemaking, producers of affected chemicals would presumably be ensuring that the information provided in their SDSs and labels remains accurate and current. Producers of hazardous chemicals are generally expected to regularly review the available information regarding any hazards that may be associated with their products and to revise SDSs and labels accordingly.

In addition, for every affected product that is newly created, reformulated, mixed with new ingredients, modified with new or different types of additives, or has any changes made in the proportions of the ingredients used, the chemical producer would be required under existing OSHA and other applicable standards to review the available hazard information, to classify the chemical in accordance with applicable hazard criteria, and to develop corresponding SDSs and labels.

The estimated costs of compliance with the proposed revisions do not include the costs associated with activities such as those described in the above paragraphs, but rather reflect only the additional costs that chemical producers would not already be expected to incur.

The estimated compliance costs associated with the proposed reclassification of hazards and changes to SDSs and labels are based on the numbers of SDSs affected. Based on the PPE report, OSHA developed estimates of the number of potentially affected SDSs by industry, for each of the industries producing the corresponding chemicals and products (as shown in Table VII-2). Downstream users, distributors, and wholesalers are expected to continue to rely on SDSs provided by manufacturers to fulfill their obligations under the OSHA standard, as has been the practice for decades. OSHA requests comments and information from the public regarding this aspect of compliance with the standard.

The costs of compliance associated with the classification of chemicals in accordance with the proposed criteria and with the revisions to the corresponding SDSs and labels for those chemicals were based on PPE industry interviews and estimated as follows.

Generally, for smaller establishments with relatively few chemicals affected, OSHA estimated the incremental compliance costs to be the equivalent of the cost of seven hours of time of a professional with the requisite expertise for each affected chemical, on average. Based on the PPE report, OSHA estimated the cost of hourly compensation for a professional for this purpose to be $47. As a result, a small establishment (with fewer than 100 employees) with 20 SDSs for 20 chemicals, for example, would have estimated incremental compliance costs of $6,580 (7 hours times 20 SDSs times $47).

In larger establishments with more affected chemicals, the incremental compliance costs were estimated to consist of two parts. First, labor costs were estimated according to the size of the establishment. OSHA, based on PPE interviews with stakeholders, estimated that entities with 100 to 499 employees would incur, on average, the equivalent of five hours of time of a professional with the requisite expertise for each affected chemical, and that entities with 500 or more employees would incur the equivalent of three hours of professional time per chemical. Based on the PPE report, OSHA estimated the hourly compensation for a professional for this purpose to be $47.

The labor cost per SDS was estimated to be lower for larger companies based on the determination that larger companies produce more SDSs, and would therefore experience efficiencies associated with producing them. These efficiencies include economies of scale, the use of software specifically designed to classify hazards and produce SDSs, and the generally lower cost per SDS associated with many mixtures.

Second, many of these larger establishments may incur additional expenditures to purchase or modify software that can be used to classify chemicals and to produce corresponding SDSs and labels. Such software is available from a variety of vendors; the software can be purchased or used on a subscription basis. Publicly available information about the products and services being offered and sold to businesses for purposes of complying with hazard communication requirements indicates that most of the relevant vendors are aware of and prepared for an upcoming transition to the GHS, and that their products and services are or will be adapted to enable compliance with the proposed revisions. In addition, some firms may purchase custom or proprietary software from private vendors to achieve compliance with existing or proposed revisions to hazard communication requirements and for other purposes.

Regardless of the particular approach individual companies may choose to most efficiently fulfill their obligations under the existing or proposed HCS, OSHA expects that a part of the costs associated with achieving compliance with the proposed revisions would involve costs attributable to software modifications. Based on industry data obtained by PPE, OSHA apportioned these costs on a per-SDS basis and estimated the cost per SDS to be $200, on average.

Based on the PPE report, OSHA estimated the numbers of SDSs produced in each industry that would potentially need to be revised under the proposed standard, as shown in Table VII-2. A total of about 880,000 SDSs, one for each type of chemical produced by an individual manufacturer in the United States, were estimated to be in potential need of revision.

In developing estimates of the compliance costs associated with the proposed rule, PPE also considered the extent to which many firms have already performed the necessary reclassifications of chemical hazards and revisions to SDSs. Some chemical hazards have already been reclassified as would be required by the proposed OSHA standard because the U.S. Department of Transportation has required such classifications as part of their regulations for the transportation of hazardous chemicals (49 CFR parts 171-180). The criteria for physical hazard classifications for purposes of transport have been internationally harmonized for some years, and these criteria formed the basis for the physical hazard criteria in the GHS. Therefore, many products intended for transport have already been classified under the new proposed physical hazard criteria as well as the existing criteria in the HCS.

Many current SDSs are already produced to varying degrees in accordance with the requirements of the proposed OSHA standard because the widely-followed ANSI industry consensus standard already reflects many of these requirements in its relevant criteria. In addition, many firms have implemented or are beginning to implement hazard reclassifications, SDS revisions, software modifications, and other changes in accordance with the requirements of the proposed OSHA standard, because these provisions are generally anticipated to be adopted as part of the implementation of the GHS in countries and regions around the world. Since some other countries are already implementing the GHS, companies in the U.S. that ship to those countries are already having to comply with the GHS for products being exported.

Research conducted by PPE indicates that all of these factors contribute to a substantial degree of current compliance with the proposed rule, even if the existing OSHA standard remains unchanged. [13] Based on the PPE report, OSHA estimates that, on average, about 53 percent of the gross costs that would otherwise be associated with the proposed revisions to the HCS have already been incurred by firms. However, this average is a result of very different levels of current compliance for different sizes of firms. PPE estimated that the percentage of firms in current compliance with the proposed revisions—with the exception of employee training—is 75 percent for firms with over 500 employees; 25 percent for firms with 100 to 500 employees; 5 percent for firms with 20 to 99 employees; and 1 percent for firms with fewer than 20 employees. OSHA used these percentages to reduce the number of firms reported in Table VII-2 for purposes of estimating the costs for affected firms to comply with the proposed revisions (again, with the exception of employee training).

Based on the preceding analysis, OSHA estimates an annualized cost of approximately $11 million for the classification of chemicals in accordance with the proposed criteria and for revisions to the corresponding SDSs and labels for those chemicals. [14]

OSHA requests data and information from the public that would assist the Agency in ensuring that any costs associated with the proposed revisions are accurately estimated. For example, OSHA would appreciate data from individual companies on the number of actively distributed SDSs; the number that would be affected by the GHS proposal; the time required to revise SDSs; the occupation and hourly cost of the individuals working on the revisions; and whether software would need to be modified or purchased and the costs of the modification or purchase.

As discussed below, OSHA received some comments from the public regarding the estimated costs associated with chemical classifications and revisions to safety data sheets in response to the Advance Notice for Proposed Rulemaking (ANPR) published by OSHA in the Federal Register on September 12, 2006 (71 FR 53617). The comments received are publicly available as part of the rulemaking record, accessible through regulations.gov, in docket OSHA-H022K-2006-0062. Relevant information submitted by the public was incorporated into the development of the methodology and estimates presented in this preliminary economic analysis.

Some commenters provided examples of cost estimates that generally support the estimates of the preliminary economic analysis. Information from other commenters provided a wide range of cost estimates. The figures presented in some comments appeared to correspond to gross costs of creating SDSs, and in other cases it was not clear whether gross or incremental costs were being presented. In general, commenters did not provide the rationale underlying their cost estimates. OSHA requests that, in submitting any data or information on compliance costs, commenters distinguish between the costs attributable to compliance with existing requirements, costs already incurred voluntarily or in compliance with another standard, and the incremental costs attributable to the new requirements associated with this rulemaking. The rationale or basis for assigning these compliance costs would also assist OSHA in developing accurate cost estimates.

One commenter, the Fragrance Materials Association of the United States, stated that its best assessment is that it would take anywhere from two to eight hours to review information and prepare new labels and safety data sheets for each hazardous chemical. (Document ID # 0061). Another commenter, the Flavor and Extract Manufacturers Association of the United States, also reported that it would take from two to eight hours to review the necessary information and produce new labels and safety data sheets for each hazardous chemical. (Document ID # 0062).

One company that produces and distributes about 4,000 different hazardous chemicals estimated that it will take four to six hours per product to prepare a GHS SDS. (Document ID # 0026).

The National Paint and Coatings Association stated that it would take approximately five hours to research the information for a product SDS/label at a small company, at a cost of about $300 per product; it also estimated that, at a medium-sized company, this same task would take from 3-5 days to 3 weeks at a cost of approximately $1,000 to $1,800, and that at a larger company, the task would be even more expensive. (Document ID # 0050).

The National Association of Chemical Distributors estimated that converting an existing SDS to the new GHS format would require about 150 hours as compared to about 100 hours currently to revise an MSDS. (Document ID # 0060).

Another commenter, Merck, which produces, imports, or distributes about 500 hazardous chemicals annually, estimated that, on average, it takes approximately 3 weeks to generate a single safety data sheet at an average cost of $1,500. Merck also stated that with a sufficient transition period of three to six years, the costs of moving to GHS would be minimal. Merck noted that the time and cost for additional changes to the GHS format should be minimal because it had already converted its SDSs to the 16-section ANSI/GHS format several years ago. (Document ID # 0072).

One trade association estimated that the costs associated with revising SDSs and labels for the 1,600 firms in the cleaning product formulator industry would total $575 million, not including the time needed to review changes to hazard classifications. The total numbers of SDSs per establishment are generally higher for the establishments represented by the trade association than the OSHA estimates for the industry category as a whole. (Document ID # 0032).

This trade association also provided some of the details underlying its cost estimates for individual companies. Cost estimates provided by the trade association for individual companies included costs per SDS as low as $30 and $80, and as high as $600 or more. One company (identified as Company #11) estimated the cost to revise the label and SDS would be $120 per product; another company (Company #2) estimated that this cost would be $2,600 per product. Some of the higher compliance cost estimates appear to be unrealistically high; for example, the estimated costs associated only with revising labels for company #3 appear to represent about 3 percent of total annual sales. While acknowledging that some firms may incur higher costs than others to revise SDSs and labels, these data generally appear to support that, at least for several firms in the industry, the costs minimally necessary to achieve compliance would be close to or less than the costs estimated by OSHA.

Several other commenters provided cost estimates related to the adoption of GHS requirements for chemical classifications and revisions to safety data sheets and labels. See, for example, Document ID #s 0015, 0018, 0024, 0036, 0079, 0105, 0107, 0116, 0128, 0141, and 0145, among others. Many estimates are broadly consistent with OSHA's estimates; in addition, some estimates appear to be similar to, but may actually be substantially lower than, OSHA's estimates to the extent they include costs attributable to the existing standard rather than just the incremental costs associated with the proposed modifications. Other estimates are substantially higher, but many of these also appear to represent gross costs associated with fulfilling hazard communication requirements without consideration of the incremental nature of the compliance costs for the proposed revisions, as discussed above.

OSHA requests additional comments and information from affected establishments and from the public regarding the nature of the incremental costs of classifying chemicals and modifying SDSs and labels associated with the proposed revisions. Comments would be most helpful to the Agency if they included the underlying data and methodology used to develop the cost estimates.

Management Familiarization and Other Management-Related Costs

The implementation of GHS as part of the OSHA HCS would require that employees currently covered by the standard become familiar with the new system. The nature and extent of the familiarization required would vary depending on an employee's job and business. OSHA considered separately various training needs that may be imposed by the proposed revisions.

Although it would not be explicitly required by the proposed revisions, some establishments may choose to provide training to managers and other employees that are not directly covered by the training requirements of the HCS. Other management-related costs may include revisions, if necessary, to existing hazard communication programs; promoting awareness of and providing information about the revisions to hazard communication programs; coordinating and integrating changes to hazard communication programs with other programs, processes, and functions; serving as an in-house resource for supporting the general adoption of GHS; creating supplemental capacity for providing training and assistance to affected employees; and other ancillary costs for company-specific changes and general hazard communication program administration that may be incurred at some establishments.

These costs could be considered discretionary in that they would not be explicitly required by the proposed regulatory provisions; however, OSHA recognizes that these costs may be incurred in practice due to the manner in which some companies have implemented and integrated hazard communication programs in their facilities. The particular circumstances that would cause these costs to be incurred partly reflect the fact that hazard communications programs often are not implemented solely for purposes of complying with the OSHA standard, but may serve a variety of other purposes that are part of and that benefit the overall production process.

In some cases, health and safety supervisors, logistics personnel, and other personnel involved in administering, implementing, and ensuring compliance with the requirements of the HCS in affected establishments would be expected by company managers to become familiar with the proposed revisions. The responsibilities of these employees may include modifying written hazard communication programs as necessary, reviewing and preparing training materials, and training new and existing employees regarding the changes. An estimated 8 hours of time, or an equivalent cost, would be associated with the necessary familiarization and implementation of revisions to hazard communication programs in affected establishments in the manufacturing sector.

In many potentially affected establishments that do not produce SDSs, and that have few affected chemicals or few affected employees, a very basic hazard communication program may achieve compliance with the OSHA standard. For these establishments, outside of the manufacturing sector, that have a health and safety supervisor, the incremental management and administrative costs associated with the proposed revisions to the OSHA standard were estimated to be 2 hours per establishment. For establishments outside of the manufacturing sector that do not have a health and safety supervisor, OSHA estimated that these costs would be negligible.

Based on the preceding analysis, OSHA estimates an annualized cost of approximately $42 million for management familiarization and other related management activities in response to GHS. [15]

OSHA requests additional comments and information from affected establishments and from the public regarding the nature of the incremental management familiarization costs associated with the proposed revisions.

Costs Associated With Training Employees

Production employees who are currently covered by and trained under the provisions of the existing HCS would need to receive some additional training to become familiar with the proposed changes to SDSs and labels.

In many potentially affected establishments that do not produce SDSs, and that have few affected chemicals or few affected employees, a very basic hazard communication program may achieve compliance with the OSHA standard. In these establishments, the incremental employee training costs associated with the proposed revisions to the OSHA standard may be relatively small. In other cases, employers may be able to integrate the necessary training into existing training programs and other methods of distributing safety and health information to employees, and thus may not incur much additional cost. Nevertheless, in order to adequately reflect the opportunity costs of devoting time and resources to the necessary training, and in order to ensure that the estimated compliance costs reflect an adequate emphasis on the familiarization with the proposed new hazard communication system, a more substantial training cost was estimated.

An estimated 30 minutes of training, in addition to training that would otherwise be received, would provide adequate time for employees to become familiar with the new system. For some occupations for which the use of hazardous chemicals is minimal and the number of hazards for which training is needed is small, OSHA estimated that 15 minutes of training would be sufficient. For some occupations in the transportation sector, where GHS pictograms are already in use, OSHA estimated that only 5 minutes of training would be needed. A complete occupation-by-occupation review of OSHA's estimates is provided in the PPE report.

The training costs associated with the proposed revisions are expected to be incurred during the transition to the new hazard communication system. Compliance with the proposed revisions is not expected to involve any additional training costs after the transition period.

Based on the preceding analysis, OSHA estimates that the annualized cost of training employees in response to GHS would be approximately $44 million. [16]

The proposed revisions may result in reductions in the costs associated with providing training for employees as required by the existing OSHA HCS. Affected companies could save considerable time and effort in training new employees in the future. The savings may be attributable in part to reducing or eliminating the need to explain the different types of formats used to convey hazard information and the different types of information included in the contents of SDSs and labels. OSHA did not quantify these potential savings in training costs associated with the proposed revisions.

OSHA requests additional comments and information from affected establishments and from the public regarding the nature of the incremental training costs associated with the proposed revisions.

Summary of Unit Cost Estimates

The following list provides a summary of the input estimates underlying the calculation of the compliance costs. It should be noted that these costs are intended to reflect only the incremental costs that would be incurred in addition to the associated costs that would be incurred in the absence of the proposed revisions to the standard. Except for employee training, these costs would apply only to those businesses not already in compliance with the proposed revisions. OSHA requests comments and information from the public regarding these estimates.

Reclassifying chemicals and modifying SDSs and labels:

  • Large establishments (over 500 employees): An average of 3 hours per SDS; in addition, for 95 percent of establishments, an average of $200 per SDS for software modifications.
  • Medium establishments (100-499 employees): An average of 5 hours per SDS; in addition, for 25 percent of establishments, an average of $200 per SDS for software modifications.
  • Small establishments (1-99 employees): An average of 7 hours per SDS.

Management familiarization and other costs:

  • Eight hours for health and safety managers and logistics personnel in the manufacturing sector.
  • Two hours for each hazard communication program manager not in the manufacturing sector.

Employee training:

  • 30 minutes per production employee in most industries;
  • 15 minutes in occupations exposed to few hazardous chemicals and types of hazards;
  • 5 minutes per employee in some occupations where GHS-type pictograms are already in use.

Appendix to Section F: Total Non-annualized Costs of Compliance

Table VII-4 shows the total non-annualized (non-discounted) compliance costs by industry and by cost element that are estimated to be incurred during the three-year phase-in of the proposed revisions. Except for employee training, these estimates include no costs for businesses already in compliance with the proposed revisions.

As shown in Table VII-4, the total cost of compliance with the proposed rulemaking over the course of the transition period of three years is estimated to be about $1.14 billion. This amount also represents the total non-annualized cost of compliance for the proposed rule. Of this amount, the cost of chemical hazard reclassification and revision of SDSs and labels is an estimated $132 million, the cost of training employees is an estimated $519 million, and the cost of management familiarization and other costs such as updates to hazard communication programs is an estimated $490 million.

BILLING CODE 4510-26-P

BILLING CODE 4510-26-C

G. Economic Feasibility and Impacts

This section presents OSHA's analysis of the potential economic impacts of the proposal and an assessment of economic feasibility. A separate analysis of the potential economic impacts on small entities (as defined in accordance with the criteria established by the Small Business Administration) and on very small entities (those with fewer than 20 employees) is presented in the following section as part of the Initial Regulatory Flexibility Screening Analysis, conducted in accordance with the criteria laid out in the Regulatory Flexibility Act.

In order to assess the nature and magnitude of the economic impacts associated with compliance with the proposal, OSHA developed quantitative estimates of the potential economic impact of the requirements on each of the affected industry sectors. The estimated costs of compliance presented in Section F of this economic analysis were compared with industry revenues and profits to provide a measure of potential economic impacts.

Table VII-5 presents data on revenues and profits for each affected industry sector, along with the corresponding estimated annualized costs of compliance in each sector. Potential impacts in the table are represented by the ratios of compliance costs to revenues and compliance costs to profits.

As is evident from the data and estimates presented in Table VII-5, the costs of compliance for the proposal are not large in relation to the corresponding revenues and profits in each of the industry sectors. The estimated costs of compliance represent about 0.0004 percent of revenues and about 0.00712 percent of profits on average across all entities; compliance costs do not represent more than 0.02 percent of revenues or more than 0.3 percent of profits in any individual industry sector.

The Agency preliminarily concludes that the proposal is economically feasible for the affected industries. In general, the courts have held that a standard is economically feasible if there is a reasonable likelihood that the estimated costs of compliance “will not threaten the existence or competitive structure of an industry, even if it does portend disaster for some marginal firms” (United Steelworkers of America v. Marshall, 647 F.2d 1189, 1272 (D.C. Cir. 1980)). The potential impacts of employer costs associated with achieving compliance with the proposal fall well within the bounds of economic feasibility in each industry sector. OSHA does not expect compliance with the requirements of the proposal to threaten the viability of employers or the competitive structure of any of the affected industry sectors.

The economic impact of the proposal is most likely to consist of a very small increase in prices for affected hazardous chemicals, of about 0.0004 percent on average. Chemical manufacturing companies, all of whom must incur the costs of compliance unless they are already doing so, should be able to pass through costs to customers. The additional costs of a one-time change to revised SDS and labeling criteria are extremely small in relation to the value of the corresponding products, and there are generally no economic substitutes, or alternatives, that would not be subject to the same requirements. It is unlikely that a price increase of this magnitude would significantly alter the types or amounts of goods and services demanded by the public or any other affected customers or intermediaries. If the compliance costs of the proposal can be substantially recouped with a minimal increase in prices, there would be little or no effect on profits.

BILLING CODE 4510-26-P

BILLING CODE 4510-26-C

In profit-earning entities, compliance costs can generally be expected to be absorbed through a combination of increases in prices or reduction in profits. The extent to which the impacts of cost increases affect prices or profits depends on the price elasticity of demand for the products or services produced and sold by the entity.

The price elasticity of demand refers to the relationship between changes in the price charged for a product and the resulting changes in the demand for that product. A greater degree of elasticity of demand implies that an entity or industry is less able to pass increases in costs through to its customers in the form of a price increase and must absorb more of the cost increase through a reduction in profits.

In the case of cost increases that may be incurred due to the requirements of the proposal, all businesses within each of the covered industry sectors would be subject to the same requirements. Thus, to the extent potential price increases correspond to costs associated with achieving compliance with the standards, the elasticity of demand for each entity will approach that faced by the industry as a whole.

Given the small incremental increases in prices potentially resulting from compliance with the proposed standards and the lack of readily available substitutes for the products and services provided by the covered industry sectors, demand is expected to be sufficiently inelastic in each affected industry to enable entities to substantially offset compliance costs through minor price increases without experiencing any significant reduction in revenues or profits.

OSHA expects the economic impact of the proposed rulemaking to be both an increase in the efficiency of production of goods and services and an improvement in the welfare of society.

First, as demonstrated by the analysis of costs and benefits associated with compliance with the requirements of the proposal, OSHA expects that societal welfare will increase as a result of these standards, as the benefits exceed the necessary compliance costs. The proposal is estimated to yield net benefits of over $500 million annually that would be achieved in a cost-effective manner.

Second, until now, many of the costs associated with the injuries, illnesses, and fatalities resulting from the risks addressed by the proposal have been externalized. For example, the costs incurred by society to supply certain products and services that are accompanied by injuries, illnesses, or fatalities from employee exposure to hazardous chemicals have not been fully reflected in the prices of those products and services. To the extent that fewer of these costs are externalized because of improved employer and employee information about hazardous chemicals in the workplace, the price mechanism will enable the market to produce a more efficient allocation of resources. However, reductions in externalities by themselves do not necessarily increase efficiency or social welfare unless the costs of achieving the reductions (including indirect and unintended consequences of regulatory approaches) are outweighed by the associated benefits, as they are in this instance.

In addition, based on an analysis of the costs and economic impacts associated with this rulemaking, OSHA preliminarily concludes that the effects of the proposal on employment, wages, and economic growth for the United States would be negligible. The effects on international trade are expected to be small but not negligible, because of the increased import and export opportunities with U.S. trading partners arising from harmonization of the U.S. system with GHS. Hence, the primary effect on international trade is likely to be beneficial.

OSHA requests comments from the public regarding these preliminary conclusions and requests information on whether and how much this proposal would affect international trade.

Statement of Energy Effects

As required by Executive Order 13211, and in accordance with the guidance for implementing Executive Order 13211 and with the definitions provided therein as prescribed by the Office of Management and Budget (OMB), OSHA has analyzed the proposed standard with regard to its potential to have a significant adverse effect on the supply, distribution, or use of energy.

As a result of this analysis, OSHA has determined that this action is not a significant energy action as defined by the relevant OMB guidance.

H. Initial Regulatory Flexibility Screening Analysis

The Regulatory Flexibility Act, as amended in 1996, requires the preparation of an Initial Regulatory Flexibility Analysis (IRFA) for proposed rules where there would be a significant economic impact on a substantial number of small firms. (5 U.S.C. 601-612). Under the provisions of the law, each such analysis shall contain:

1. A description of the impact of the proposed rule on small entities;

2. A description of the reasons why action by the agency is being considered;

3. A succinct statement of the objectives of, and legal basis for, the proposed rule;

4. A description of and, where feasible, an estimate of the number of small entities to which the proposed rule will apply;

5. A description of the projected reporting, recordkeeping and other compliance requirements of the proposed rule, including an estimate of the classes of small entities which will be subject to the requirements and the type of professional skills necessary for preparation of the report or record;

6. An identification, to the extent practicable, of all relevant Federal rules which may duplicate, overlap or conflict with the proposed rule; and

7. A description and discussion of any significant alternatives to the proposed rule which accomplish the stated objectives of applicable statutes and which minimize any significant economic impact of the proposed rule on small entities, such as

(a) The establishment of differing compliance or reporting requirements or timetables that take into account the resources available to small entities;

(b) The clarification, consolidation, or simplification of compliance and reporting requirements under the rule for such small entities;

(c) The use of performance rather than design standards; and

(d) An exemption from coverage of the rule, or any part thereof, for such small entities.

The Regulatory Flexibility Act further states that the required elements of the IRFA may be performed in conjunction with or as part of any other agenda or analysis required by any other law if such other analysis satisfies the relevant provisions.

While a full understanding of OSHA's analysis and conclusions with respect to costs and economic impacts on small businesses requires a reading of the complete PEA and its supporting materials, this IRFA will summarize the key aspects of OSHA's analysis as they affect small businesses.

1. A Description of the Impact of the Proposed Rule on Small Entities.

The proposed regulation would require classification of chemicals, especially chemical mixtures, somewhat different from current hazard determination methods; a standardized format for the organization of MSDSs (now called SDSs); standardized labels and standardized pictograms; and training for affected employees on these changes. (Some commenters argued that GHS would also impose more stringent testing requirements, but as explained in Section V of the preamble, the HCS does not currently require testing of chemicals, and will not require testing with adoption of the GHS.)

For the purpose of its cost analysis, OSHA estimated three types of cost:

(1) Costs to chemical producers of classifying chemicals, reformatting SDSs, and developing new labels;

(2) Costs for safety and health managers and logistics personnel to familiarize themselves with the standard (although not required by the regulation, this is a necessary step in its implementation); and

(3) Costs of training affected employees on how to find the information they need on SDSs and to comprehend pictograms and standard labels.

OSHA believes that each of these is a one-time cost that would be incurred during the three-year transition period after the final rule is published. OSHA anticipates that, once the final rule is implemented, the costs under GHS will be equivalent to the costs under the existing HCS system. In other words, once chemical producers and distributors set up for and shift to the GHS system, OSHA expects there will be no additional costs arising from the proposed rule for classification, SDSs, and labeling.

OSHA also anticipates that, after the three-year transition period, the familiarization costs for health and safety managers, logistics personnel, and emergency response planners and the training costs for affected employees will be lower under the uniform GHS system than under the existing HCS system. (However, in its estimates of economic impacts, OSHA has not included any cost savings for the expected lower training costs.)

OSHA welcomes comments on these points, which are critical to OSHA's economic analysis of costs, benefits, and economic impacts.

OSHA's criteria for determining whether there are significant economic impacts on a substantial number of small firms are that, for any given industry, the annualized costs as a percentage of revenues do not exceed 1 percent and that the annualized costs as a percentage of profits do not exceed 5 percent. All of OSHA's calculations of the economic impacts on small firms totally ignore any offsetting benefits of any kind, even though OSHA estimates that, for most small firms, the benefits of this rule will actually exceed the costs.

OSHA's industry-by-industry analysis, both for small firms as defined by SBA and for very small firms with fewer than 20 employees, shows that in no industry size class do the annualized costs exceed 0.013 percent of revenues or 0.4 percent of profits. For affected small firms as defined by SBA, the average annualized cost per firm of the proposed rule would be $16 per year. In terms of chemical producing industries only, the average annualized cost per small firm as defined by SBA would be $452 per year. For affected firms with fewer than 20 employees, the average annualized cost per firm of the proposed rule would be $12 per year, and the average annualized cost per firm that produces chemicals would be $167 per year.

Given these results, OSHA concludes that the proposed rule will not have a significant economic impact on a substantial number of small firms. Thus, an IRFA is not required for this rulemaking. However, recognizing the possible value that such an analysis may provide, OSHA has voluntarily included the elements of the IRFA as part of this Initial Regulatory Flexibility Screening Analysis (IRFSA) and has analyzed the potential impact of the proposed revisions on small entities. As described in Section D of this economic analysis, the proposed revisions to HCS, on the whole, are expected to result in significant net benefits to employers, as the associated cost savings outweigh the corresponding compliance costs. The underlying analysis included the effects on small entities, and this conclusion generally applies to the small entities affected by the proposed rule.

In order to ensure that any potential significant adverse impact on a substantial number of small entities would be appropriately considered, OSHA also specifically evaluated the impact on small entities of the costs of compliance alone, without regard to the associated savings.

The total annualized cost of compliance with the proposal for small entities is estimated to be approximately $63 million, as shown by industry in Table VII-6.

To assess the potential economic impact of the proposal on small entities, OSHA calculated the ratios of compliance costs to profits and to revenues. These ratios are presented for each affected industry in Table VII-6. OSHA expects that among small entities potentially affected by the proposal, the average increase in prices necessary to completely offset the compliance costs would be 0.0009 percent. The average price increase necessary to completely offset compliance costs would not exceed 0.02 percent among small entities in any single affected industry sector.

In the event that no costs could be passed through, the compliance costs could be completely absorbed through an average reduction in profits of less than 0.02 percent. In most affected industries the compliance costs could be completely absorbed through an average reduction in profits of less than 0.05 percent; the reduction would be no more than 0.4 percent in any of the affected industries.

To further evaluate the potential for any adverse effects on small entities resulting from the proposal, OSHA assessed the short-term impacts that may be associated with the compliance costs during the transition period.

BILLING CODE 4510-26-P

BILLING CODE 4510-26-C

The total non-annualized compliance costs for small entities during the three-year transition period are estimated to be $740 million, or about $247 million per year for three years. Thus, the potential temporary impact would be about 0.003 percent of revenues or about 0.1 percent of profits, on average, per year for three years.

In order to further ensure that potential impacts on small entities were fully analyzed and considered, OSHA also separately examined the potential impacts of the proposed standard on very small entities, defined as those with fewer than 20 employees. As shown in Table VII-7, the total annualized costs for entities in this size class would be an estimated $40 million. The annualized costs represent about 0.001 percent of revenues and less than 0.03 percent of profits. The total non-annualized compliance costs for very small entities during the three-year transition period are estimated to be $463 million, or about $154 million per year for three years. Thus, the potential temporary impact would be less than 0.005 percent of revenues or 0.15 percent of profits, on average, per year for three years.

In order to more carefully focus on the industry sectors most likely to have significant economic impacts, OSHA carefully examined those industries in the chemical manufacturing and petroleum and coal products manufacturing sectors (“chemical and petroleum producers”) that produce chemicals and SDSs. OSHA examined the extent to which these firms might have significant economic impacts if they produced an unusually high number of chemical products requiring SDSs.

To examine this issue, OSHA examined all small chemical and petroleum producers with respect to their costs as a percentage of revenues and profits. Using the same cost estimation methods as the base analysis, OSHA estimated how many separate chemical products a small firm would have to produce for its annualized costs of compliance with the proposed rule to exceed 5 percent of profits. OSHA found that the firm would have to produce 3,385 distinct chemical products, each requiring its own SDS. OSHA thinks it very unlikely that there are substantial numbers of small firms (with an average of 27 employees) that produce 3,385 or more distinct chemical products. Swedish data show that less than 0.1 percent of all firms (including large firms) in Sweden produce more than 500 distinct chemical products. (Swedish Chemical Agency, http://www.kemi.se/templates/Page____4268.aspx, 2007 data.)

OSHA conducted a similar analysis for very small firms with fewer than twenty employees. This analysis found that such firms, with an average of 4.7 employees, would need to produce more than 140 distinct chemical products for costs to exceed 5 percent of profits. OSHA estimates that this would be a very rare situation.

Further, even if small firms could be found that produce more than 3,385 chemical products and very small firms that produce more than 140 chemical products, the costs would probably be much lower than OSHA estimates. First, firms producing this many distinct products probably would not produce SDSs and labels by hand, as OSHA assumes most small firms do, but would instead invest in appropriate software to lower their costs, as most larger firms do. Second, firms producing large numbers of chemical products commonly do so because they sell a variety of different mixtures. Once appropriate data for the ingredients of these mixtures had been developed, using the bridging principles outlined in Appendix A of the preamble, small firms developing SDSs and labels for each mixture would take far less than the 7 hours per chemical product that OSHA has estimated for small firms to convert to the GHS system.

BILLING CODE 4510-26-P

BILLING CODE 4510-26-C

OSHA therefore concludes that there are not a substantial number of firms that would incur significant economic impacts as a result of producing a very large number of chemical products.

OSHA remains concerned with the possible problems of small and very small firms that might produce very large numbers of distinct chemical products. OSHA welcomes comments on the issue of whether there are small and very small firms that produce a very large number of products, what industries they are in, and their anticipated costs to convert to the GHS system.

2. A description of the reasons why action by the agency is being considered.

OSHA's HCS was first adopted in 1983 for manufacturing (48 FR 53280). Later the Agency expanded the scope of coverage to include all industries where employees are potentially exposed to hazardous chemicals (52 FR 31852).

The HCS requires chemical manufacturers and importers to evaluate the hazards of the chemicals they produce or import. The rule provides definitions of health and physical hazards to use as the criteria for determining hazards in the evaluation process. The information about the hazards and protective measures is then required to be conveyed to downstream employers and employees by putting labels on containers and preparing and distributing safety data sheets. All employers with hazardous chemicals in their workplaces are required to have a hazard communication program, including container labels, safety data sheets, and employee training.

Ensuring that this information is available in workplaces helps employers design and implement appropriate controls for chemical exposures, and gives employees the right-to-know and the knowledge of the hazards and identities of the chemicals, as well as allowing them to participate actively in the successful control of exposures. Together, these actions of employers and employees reduce the potential for adverse effects to occur. The information transmitted under the HCS requirements provides the foundation upon which a chemical safety and health program is built in the workplace. Without this information, appropriate controls could not be identified and implemented.

OSHA's HCS is designed to disseminate information on chemicals to precipitate changes in handling methods and thus protect those exposed to the chemical from experiencing adverse effects. To protect employees and members of the public who are potentially exposed to chemicals during their production, transportation, use, and disposal, a number of countries have developed laws that require information about those chemicals to be prepared and transmitted to affected parties. These laws vary with regard to the scope of chemicals covered, definitions of hazards, the specificity of requirements (e.g., specification of a format for safety data sheets), and the use of symbols and pictograms. The inconsistencies between the various laws are substantial enough that different labels and safety data sheets must often be used for the same product when it is marketed in different nations. For example, Canada has established requirements for labels under its Workplace Hazardous Materials Information System (WHMIS). WHMIS requires that labels include specified symbols within a defined circle. U.S. chemical manufacturers must label their chemicals accordingly for marketing in Canada.

Development of multiple sets of labels and safety data sheets for each product when shipped to different countries is a major compliance burden for chemical manufacturers, distributors, and transporters involved in international trade. Small businesses may have particular difficulty in coping with the complexities and costs involved, and it has been argued that these differing requirements may be a technical (non-tariff) barrier to trade.

These concerns led, in June 1992, to a mandate from the United Nations Conference on Environment and Development (UNCED) (Chapter 19 of Agenda 21), supported by the U.S., calling for development of a globally harmonized chemical classification and labeling system. The negotiations were extensive and spanned a number of years. The product resulting from this effort, the Globally Harmonized System of Classification and Labeling of Chemicals, was formally adopted by the new United Nations Committee of Experts on the Transport of Dangerous Goods and the Globally Harmonized System of Classification and Labeling of Chemicals in December 2002.

The proposed modifications to the HCS incorporate the GHS's requirements. They would require chemical manufacturers to apply new hazard classification criteria to their chemicals and to prepare and distribute new labels and safety data sheets. Further, these SDSs and labels would be standardized in a way that they are not under the existing hazard communication standard. OSHA's current performance-based approach to SDSs and labeling can create confusion among those who seek to use hazard information effectively. For example, labels and safety data sheets may include symbols and hazard statements that are unfamiliar to readers or not well understood. This lack of standardization and the absence of pictograms are particularly a problem for U.S. workers not literate in English. Containers may be labeled with such a large volume of information that important statements are not easily recognized.

OSHA believes that adoption of these new requirements would benefit employers and enhance employee safety. Employers who use chemicals, and exposed employees, would benefit from receiving the revised labels and safety data sheets prepared in a consistent format. The information should be easier to comprehend and access in the new approach, allowing it to be used more effectively for the protection of employees. The primary effect in workplaces where chemicals are used but not produced would be to integrate the new approach into the workplace hazard communication program, including assuring that both employers and employees understand the pictograms and other information provided on the chemicals.

OSHA believes that adoption of the GHS would improve labels and SDS comprehensibility through implementation of a standardized approach. The current regulatory system includes a performance-oriented approach to labels and SDSs, allowing the producers to use whatever language or format they choose to provide the necessary information. This results in a lack of consistency that makes it difficult for users of chemicals to properly identify their hazards and protective measures, particularly when purchasing the same product from multiple suppliers. Having the information provided in the same words and pictograms on labels, as well as having a standardized order of information on SDSs, would help all users, including employers, employees, and safety and health responders, more easily identify the critical information necessary to protect employees.

In addition, American employees and employers should receive benefits from the international adoption of GHS. Development of the GHS system required extensive work by a great number of people, and resources from many countries and organizations. The reason it received such support is that there is a belief that there are significant benefits associated with implementation of a globally harmonized approach to hazard communication. Countries, international organizations, chemical producers, and users of chemicals would all benefit. There are at least four reasons to expect that GHS will be adopted globally.

First and foremost, implementation of the GHS would enhance protection of humans and the environment. Occupationally related injuries, illnesses, and fatalities remain a serious problem in the U.S. For example, although likely to contain very significant underreporting, data from the Bureau of Labor Statistics indicate that, in 2007, employees suffered an estimated 55,400 illnesses attributable to chemical exposures (BLS, 2008), and that some 17,340 chemical-source injuries and illnesses involved days away from work (BLS, 2009). As shown in the preliminary economic analysis, the adoption of the proposed revisions is expected to result in a significant reduction in injuries, illnesses, and fatalities among U.S. employees exposed to hazardous chemicals. In addition, while some countries, such as ours, already have the benefits of protection under existing systems, the majority of countries do not have such comprehensive approaches. Thus, implementation of the GHS would provide these countries with the important protections that result from dissemination of information about chemical hazards and protective measures. In our country, we expect to improve and build on protections we already have.

Second, implementation of such an approach would facilitate international trade in chemicals. It would reduce the burdens caused by having to comply with differing requirements for the same product, and allow companies who do not have the resources to deal with those burdens to be involved in international trade.

Third, one of the initial reasons this system was pursued internationally involved concerns about animal welfare and the proliferation of requirements for animal testing and evaluation. Existing systems with different definitions of hazards often result in duplicative testing to produce data related to the varying cut-offs in the different systems. Having one agreed definition would reduce this duplicative testing. It should be noted, however, that OSHA has never had testing requirements. The HCS is based on collecting and evaluating the best available existing evidence on the hazards of each chemical.

Fourth, information transmittal systems provide the underlying infrastructure for the sound management of chemicals in a country. Those countries that do not have the resources to develop and maintain such a system can use the GHS to build their chemical safety and health programs. Since it has been developed, and will be maintained, through an international approach, national resources to accomplish chemical safety and health can be streamlined. Unlike some other issues, a country's approach to the sound management of chemicals definitely affects others countries. In some cases, bordering countries may experience pollution and other effects of uncontrolled chemical exposures. In all countries, there is a need to acquire sufficient information to properly handle the chemical when it is imported from other countries. Thus having a coordinated and harmonized approach to the development and dissemination of information about chemicals would be mutually beneficial to importing and exporting countries.

In the U.S., there are four primary regulatory agencies that exercise jurisdiction over chemical hazard communication: OSHA; the Department of Transportation, which regulates chemicals in transport; the Consumer Product Safety Commission, which regulates consumer products; and the Environmental Protection Agency, which regulates pesticides and has other labeling authority under the Toxic Substances Control Act. These agencies are not domestically harmonized in terms of definitions of hazards and other requirements. If all four agencies adopt the GHS, the U.S. would have the additional benefit of harmonizing the overall U.S. approach to classification and labeling. Since most chemicals are produced in a workplace and shipped elsewhere, nearly every employer deals with at least two sets of Federal requirements. Thus every producer would be likely to experience some benefits from domestic harmonization.

OSHA has made a preliminary determination that the proposed revisions would improve the quality and consistency of information provided to employers and employees regarding chemical hazards and associated protective measures. The Agency anticipates this improved information would enhance the effectiveness of the HCS in ensuring that employees are apprised of the chemical hazards to which they are exposed, and in reducing the incidence of chemical-related occupational illnesses and injuries. OSHA preliminarily estimates that (1) savings in benefits from improved employee health and safety exceed the costs of the proposed rule, and (2) cost savings to chemical users exceed the costs of the proposed rule.

An additional and more complete discussion of the reasons why this standard is being proposed by the Agency is provided in other parts of the preamble section of this Notice of Proposed Rulemaking (NPRM).

3. Statement of the objectives of, and legal basis for, the proposed rule.

The primary objective of the proposed revisions to the OSHA HCS is to achieve the potential benefits of the OSHA HCS in a more comprehensive, efficient, and effective manner. The revisions are expected to provide an increased degree of occupational safety and health for employees exposed to hazardous chemicals in the workplace.

Another objective of the proposed revisions is to provide updated, clear, and comprehensive standards regarding the classification of chemical hazards and the manner in which relevant information about chemical hazards is disseminated to affected employees.

The intent of the HCS is to ensure that the hazards of all chemicals are evaluated and that information concerning chemical hazards and associated protective measures is transmitted to employers and employees. The standard achieves this goal by requiring chemical manufacturers and importers to review available scientific evidence concerning the physical and health effects of the chemicals they produce or import to determine if they are hazardous.

For every chemical found to be hazardous, the chemical manufacturer or importer must develop a container label and an SDS and provide both to downstream users of the chemical. All employers with employees exposed to hazardous chemicals must develop a hazard communication program and ensure that exposed employees are provided with labels, access to SDSs, and training on the hazardous chemicals in their workplace.

The three information components in this system—labels, SDSs, and employee training—are all essential to the effective functioning of the program. Labels provide a brief, conspicuous summary of hazard information at the site where the chemical is used. SDSs provide detailed technical information and serve as a reference source for exposed employees, industrial hygienists, safety professionals, emergency responders, health care professionals, and other interested parties. Training is designed to ensure that employees understand the chemical hazards in their workplace and are aware of protective measures to follow.

Labels, SDSs, and training are complementary parts of a comprehensive hazard communication program—each element reinforces the knowledge necessary for effective protection of employees.

Information provided in accordance with the HCS serves to reduce the incidence of chemical-related illnesses and injuries in the workplace. This is accomplished by modifying the behavior of both employers and employees. Providing information to employers enables them to implement protective measures in the workplace. Less hazardous alternatives may be chosen, or appropriate engineering controls, work practices, and personal protective equipment can be selected. Improved understanding of chemical hazards by supervisory personnel results in safer handling of hazardous substances, as well as proper storage and housekeeping measures.

Employees provided with information and training on chemical hazards are able to fully participate in the protective measures instituted in their workplaces. Knowledgeable employees can take the steps required to work safely with chemicals in their workplace and are able to determine what actions are necessary if an emergency occurs. Information on chronic effects of exposure to hazardous chemicals helps employees recognize signs and symptoms of chronic disease and seek early treatment. Information provided under the HCS also enables health and safety professionals to provide better services to exposed employees. Medical surveillance, exposure monitoring, and other services are enhanced by the ready availability of health and safety information.

OSHA believes that the comprehensive approach adopted in the HCS, which includes requiring evaluation of chemicals and the transmittal of information through labels, SDSs, and training, is sound. This proposed rule does not alter that approach. Rather, the proposed rule is intended to improve the effectiveness of the HCS by enhancing the quality and consistency of the information provided to employers and employees. OSHA believes this can be accomplished by revising the requirements of the standard to conform to the more specific and detailed provisions of the GHS for classification, labeling, and SDSs.

The legal basis for the rule is the responsibility given the Department of Labor through the Occupational Safety and Health (OSH) Act of 1970. The OSH Act authorizes and obligates the Secretary of Labor to promulgate mandatory occupational safety and health standards as necessary “to assure so far as possible every working man and woman in the Nation safe and healthful working conditions and to preserve our human resources.” 29 U.S.C. 651(b). The OSH Act gives the Agency authority to issue and revise standards and regulations to further this goal. A thorough discussion of the legal basis can be found in the preamble to the proposed standard in Section VI—Pertinent Legal Authority.

4. Description of and estimate of the number of small entities to which the proposed rule will apply.

OSHA has completed a preliminary analysis of the impacts associated with this proposal, including an analysis of the type and number of small entities to which the proposed rule would apply, as described above. In order to determine the number of small entities potentially affected by this rulemaking, OSHA used the definitions of small entities developed by the Small Business Administration (SBA) for each industry.

The proposed standard would impact firms that are the primary producers or distributors of hazardous chemicals, and firms whose employees are exposed to hazardous chemicals. Based on the definitions of small entities developed by SBA for each industry, the proposal is estimated to potentially affect a total of 4,215,404 small entities, as shown in Table VII-6. The rule would have its greatest impacts on the 72,000 small firms that produce chemicals that require SDSs and labels.

5. Description of the projected reporting, recordkeeping and other compliance requirements of the proposed rule.

The proposed standard includes revised criteria for classification of chemical hazards; revised labeling provisions that include requirements for use of standardized signal words, pictograms, and hazard statements; a specified format for safety data sheets; and related revisions to definitions of terms used in the standard, employee information and training requirements, and other sections of HCS.

The preamble to the proposed standard provides a comprehensive description of, and further detail regarding, the compliance requirements of the proposed rulemaking. A description of the types of entities which would be subject to the new and revised requirements, and the types of professional skills necessary for compliance with the requirements, is presented in the relevant sections of this economic analysis and the corresponding supporting research, and is summarized below with a summary of unit costs. Except for employee training, these costs would apply only to those businesses not already in compliance with the proposed revisions. OSHA requests comments and information from the public regarding these estimates:

Reclassifying chemicals and modifying SDSs and labels:

  • Medium establishments (100-499 employees): an average of 5 hours per SDS; in addition, for 25 percent of establishments, an average of $200 per SDS for software modifications.
  • Small establishments (1-99 employees): an average of 7 hours per SDS.

Management familiarization and other costs:

  • Eight hours for health and safety managers and logistics personnel in the manufacturing sector.
  • Two hours for each hazard communication program manager not in the manufacturing sector.

Employee training:

  • 30 minutes per production employee in most industries;
  • 15 minutes in occupations exposed to few hazardous chemicals and types of hazards;
  • 5 minutes per employee in some occupations where GHS-type pictograms are already in use.

6. Federal rules which may duplicate, overlap or conflict with the proposed rule.

OSHA has not identified any other Federal rules which may duplicate, overlap, or conflict with the proposal, and requests comments from the public regarding this issue.

7. Alternatives to the proposed rule which accomplish the stated objectives of applicable statutes and which minimize any significant economic impact of the proposed rule on small entities.

As discussed in Section IV, this rulemaking is unique for OSHA in that it seeks to improve employee protections by adopting an internationally harmonized approach to hazard communication issues. While the current HCS has provided protections for exposed workers by disseminating information about chemicals in their workplaces for many years now, the approach taken in the GHS strengthens and refines the system, and gives OSHA the opportunity to improve hazard communication by adopting it. The GHS has the same general concept of an integrated, comprehensive process of identifying and communicating hazards, but provides more extensive criteria to define the hazards in a consistent manner, as well as standardizes label elements and SDS formats to help to ensure that the information is conveyed consistently.

OSHA has preliminarily concluded that required adoption of GHS is the best approach to modifying the HCS to achieve the goals of global harmonization, ease of use, and improved health and safety. As addressed in Section XV of the preamble, many commenters supported the concept of OSHA moving forward to adopt the GHS. Several objected to adoption, and OSHA has identified and responded to their concerns in Section XV of the preamble as well. In addition, there were several commenters who noted that small chemical manufacturers that are not engaged in international trade of chemicals would have a large burden associated with adopting the GHS, and questionable benefits due to their lack of involvement in international trade. The Small Business Administration (SBA) suggested that OSHA “consider `grandfathering' or exempting small businesses that do not export regulated chemicals.” (Document ID # 0022) Others simply noted that they believed there would be high costs and limited benefits for such employers, or that it would be costly and difficult to adopt (Document ID #s 0015, 0026, 0178, and 0144). There was no discussion in any of these comments about how this might work in the revised standard.

None of these commenters suggested a detailed approach to exactly how such a grandfathering or exemptions might work. OSHA welcomes comments on how such approaches might work.

A somewhat different alternative that might achieve the goals of those employers who anticipate high costs for little benefit to themselves would be for OSHA to consider simply facilitating the voluntary adoption of GHS. With some very minor exceptions that could easily be changed by rule, the existing HCS performance-based approach to MSDS would permit chemical producers and importers to use the proposed GHS SDS format and approach. They could not however, adopt the GHS classifications without a change to the rule allowing the use of GHS classifications where they differed from those in HCS. The use of labels adopting GHS signal words, precautionary statements, formats, and pictograms could be possible under the HCS performance-based approach to labels. However, it should be carefully noted that, although the resulting label might appear GHS compliant, it need not actually be GHS-compliant, and in some case would not be based on the GHS classifications. Further, individual firms could produce labels using GHS formats, etc., with meanings quite different from those in GHS.

The advantages of a system that simply facilitated voluntary adoption of GHS are that (1) those engaged in international trade, whether as exporters or importers, could obtain the full benefits of international harmonization; (2) those producers of chemicals who saw no market advantage to changing systems would not need to incur the costs associated with changing their hazard classification, MSDSs, and labels and (3) it is possible that employee training under a performance-based system for MSDSs and labels would not need to be required or changed.

OSHA sees a number of disadvantages to a rule that simply facilitates the voluntary adoption of GHS. First consider the issues of a common MSDS/SDS format versus MSDS/SDS formats that can vary in any way whatsoever while meeting a standard of what an MSDS must contain. Such an approach would eliminate a proportion of the possible benefits from knowing where to look in an SDS for the information one wants or needs, since many SDSs will still not be standardized.

From OSHA's perspective, a key issue of concern in such an approach is that the classification criteria in the GHS are different from the hazard definitions in the current HCS. In general, as discussed in Section XV of the preamble, they cover the same scope of hazard, so these differences do not result in significant differences in the chemicals covered. But the GHS criteria divide most of the hazard classes into hazard categories that convey the severity of the effect, while few of the hazard definitions in the current HCS take this approach. The standardized label elements are associated with these specific hazard categories, i.e., the harmonized pictograms, signal words, and hazard statements are assigned by hazard category and reflect the degree of hazard it presents to those exposed. Likewise, the precautionary statements assigned are also reflective of the degree of hazard, with responses related to these presumed hazard levels.

Third, consider the possible disadvantages of not having a common, well-understood labeling system with signal words, pictograms, precautionary statements and common formatting. In the absence of such a system it would be extremely difficult to teach persons not literate in English how to understand labels, and even those literate in English may have difficulty with major differences in the symbols and language used for the same substance or hazard.

It should also be noted that allowing the voluntary use of GHS might not be considered GHS-compliant as the phrase is used in GHS publications.

It is difficult to quantify the benefits and costs of the alternative of simply facilitating adoption of GHS. Part of the problem is that it is difficult to forecast the extent to which persons would voluntarily adopt GHS. OSHA therefore considered two scenarios. In the first scenario, there is no extensive adoption of GHS and GHS becomes simply a minor sub-class of the performance-oriented options already available. This scenario has the effect of minimizing the costs associated with the facilitation of voluntary adoption of GHS, but at the expense of minimizing the benefits of this alternative. In the second scenario, GHS would be adopted widely enough to become the norm for hazard communication, but some would continue their existing HCS approaches unchanged. Under this scenario, most firms would insist that their health and safety managers and logistics personnel be thoroughly familiar with GHS, and that employees be trained on GHS. This scenario minimizes the loss in benefits associated with the first scenario, but involves much greater costs than scenario 1 and may involve significantly increased costs over the option of full compliance with GHS. OSHA believes that the actual results will fall between these two scenarios and is seeking comment on the relative likelihood of these or other scenarios.

OSHA suspects that second scenario might be the more likely possibility. For example, the standardized MSDS system adopted by GHS is widely used in the U.S., particularly by large firms and firms with many MSDSs, though many have not adopted this system. Domestic and international producers, and large and small producers are not mutually exclusive—a large business engaged in international trade can not simply implement the GHS regardless of its suppliers. Small businesses sell to large businesses. If small businesses do not adopt the GHS, then the large businesses would have to generate GHS classifications for chemicals they buy from them in order to follow the GHS. It would be difficult for them to do this, particularly for mixtures, since they are not the producer of the chemicals. This concept was addressed in comments regarding the effective dates for the rule, when many suggested it was not appropriate to differentiate dates based on the size of the business. For example, ORC Worldwide, Inc. stated (Document ID # 0123):

OSHA should consider a company's place in the manufacturing supply chain, not size, in determining how the phase-in is implemented. It would be sensible to start with producers of raw materials and basic chemicals. The technical information, classification and categorization they perform will be useful downstream for the intermediate chemical producers and specialty chemical manufacturers. Lastly, the end user will benefit from the influx of information developed by the upstream professionals.

Just as the size of the company may not be an appropriate criterion to determine when that company should be in compliance, it also does not appear to be a useful way to determine whether the GHS provisions should be adopted by them. It is difficult to determine how a voluntary system, or a system based on business size, would be successfully implemented and enforced given the structure of the supply system. Because of these factors, OSHA anticipates that many smaller firms who may think they do not need GHS may be forced through the market to adopt the system to satisfy the needs of customers who do engage in international trade.

Under the first scenario, with no extensive voluntary adoption of GHS, the annualized costs $11 million per year for reclassification of chemicals and the $44 million in annualized costs for one-time retraining of workers would be largely eliminated. OSHA estimates that the $45 million in annualized costs for health and safety managers and logistics personnel to familiarize themselves with the GHS system would still be incurred. This alternative might add a continuing cost not present under either system of the need for new health and safety managers and logistics personnel to be familiar with both systems. Assuming a 5 percent annual turnover among such professional, assuring continuing knowledge of both systems would add costs of $25 million per year. This alternative under Scenario 1 would thus reduce the costs from $97 million per year to between $42 million per year and $77 million per year depending on whether it is assumed that new health and safety managers and logistics personnel would need to be familiar with both systems. In return for this reduction in costs, under Scenario 1, because of the assumption of no significant adoption of GHS, the benefits of $851 million per year are also lost. Furthermore, this analysis ignores non-quantified benefits of full adoption of GHS, such as decreases in training costs associated a full GHS system.

In choosing the voluntary adoption of GHS alternative, OSHA would be ignoring the potentially substantial health and safety benefits arising from the economically feasible (and, for most businesses, the economically desirable) option of full compliance with GHS and instead adopting a system with no such health and safety benefits for the sole reason of possibly saving a small minority of all affected businesses some costs.

Under Scenario 2, with widespread voluntary adoption of GHS, more benefits would be achieved than under Scenario 1, but all the benefits available under the proposed rule would not be achieved, and OSHA believes there would be greater costs than under the option of requiring full compliance with GHS. However, if widespread adoption of GHS is to result in substantially higher benefits than under Scenario 1, then health and safety managers and logistic personnel would have to be fully familiar with both systems, and employees would also need to be trained on GHS as the primary system and not just as one of many performance-oriented options. Thus, Scenario 2 would save some portion of the $11 million in annualized costs per year spent by chemical producers for reclassification and modifying SDSs and labels. However, the full costs of management familiarization and one-time employee training would still need to be incurred. In addition continuing costs would have to be incurred for new health and safety managers and logistic personnel to familiarize themselves with two systems and for new employees to be trained on both systems. Assuming turnover of 5 percent for manager and 20 percent for employees, the associated annual costs would be $150 million per year. Under Scenario 2, the alternative of facilitating voluntary adoption would achieve some portion of the benefits of GHS but with significantly greater costs—an additional $150 million per year for continuing GHS training of new employees and GHS familiarization for new health and safety managers and logistics personnel, offset by a very modest reduction in costs to chemical producers.

In terms of benefits, both OSHA's proposed full GHS compliant approach and that of a dual system would retain possible benefits to chemical producers and to international trade. However, OSHA is concerned that the confusions arising might negate some of the benefits associated with reduced injuries, illnesses and fatalities. While there would still be some situations where use of GHS would prevent injuries, there would also be situations where confusion and misunderstanding would lead to injuries, illnesses, and fatalities that might not otherwise be incurred. For example, employees used to seeing pictograms might easily make the false assumption that chemicals without a pictogram are safe. This has the potential to eliminate a significant portion of the annual health and safety benefits. Other benefits would also need to be reduced, though it is not clear by how much.

In addition to the chosen alternative of full compliance with GHS, OSHA also considered options requiring full compliance with some but not all portions of GHS. One such option would be to adopt the provisions of the GHS that are presumed to provide the greatest benefits at the least cost. For example, OSHA could adopt the standardized label provisions without the associated hazard classification criteria. Employers would be free to continue to use the existing hazard determination scheme, but present the label information in the standardized form anticipated under the GHS. Since the standardized labels appear to be relatively inexpensive to implement, while reviewing classifications is more costly, this has the potential to reduce the overall cost of implementation of the revised rule.

This option—adopting the label provisions but not the classification criteria—presents many of the same concerns. First, the reason the label provisions are relatively cost-efficient to adopt is that the GHS assigns the various required elements by hazard class and category. It is basically a cookbook approach. Once the classification or re-classification has been accomplished, the GHS provides the specific information for the label.

Requiring this standardized approach to labeling without the infrastructure of the criteria would be more burdensome for the chemical manufacturer to accomplish, though OSHA could consider whether it would be appropriate to provide criteria for HCS classification under this alternative that would reduce burden. However, OSHA is also concerned that this alternative would result in labels that may look the same but which actually do not have consistent warnings based on the precise hazardous effect. Without the GHS criteria that breaks hazard classes into multiple categories for most effects, it would be difficult to relate the label elements to the hazard determinations under the current HCS. For example, the current standard treats all carcinogens the same way, rather than differentiating them into several categories. OSHA would either have to provide some type of decision logic to employers in order to have a consistent approach or allow the responsible party to determine the appropriate labeling elements that should be included on the label. The most protective approach would be to treat all carcinogens or other effects as being in the most hazardous category of each class so there will be no choice of label elements that would cause differences among employers. Regardless, chemical producers will have to undergo an assessment of their current determinations and attempt to relate them to the established hazard categories. This will be difficult, particularly for small producers. Alternatively, OSHA could create a regulatory system assigning HCS categories to each GHS label, but this would be totally contrary to the performance-orientation of the current HCS system, as well as having undetermined costs. It is thus unlikely that this would provide significant savings relative to simply reviewing classifications for purposes of putting the chemicals into GHS classes and categories.

However, apart from this burden, the benefits of standardized labeling would be reduced by not having common criteria upon which they are based. Chemical producers following this approach would likely not be able to use their labels in other countries where the GHS has been adopted. Hence, there would be costs of adoption without commensurate benefits in either comprehensibility or facilitation of trade.

Another type of dual approach would have OSHA adopt some, but not all, of the label elements. In particular, the Agency might not adopt the exact language of the precautionary statements since this language has been codified but are not yet considered to be “harmonized” under the GHS—they are provided for guidance and reference, but competent authorities may choose to implement other statements. The exact language for precautionary statements could be adopted later when they are harmonized under the GHS. Alternatively, OSHA could either allow label preparers to use whatever precautionary statements they deem appropriate or develop its own set of statements to require.

The precautionary statements, however, are the part of the GHS label that provides the measures to follow to ameliorate the possible hazardous effects of exposure. Delaying adoption of the precautionary statements would likely reduce the effectiveness of the labels significantly, and reduce the appropriate information on the SDSs as well. Labels that lack a precautionary statement would not be fully harmonized. The second alternative, to simply require precautionary statements, but not to specify what they are, would provide some protection but would not correct the current situation of inconsistent precautions due to the performance-oriented approach that allows the label preparer to determine what they are or if they are included. One communication advantage of providing the information in the same language from label-to-label is that workers and other users can be assured that the same action is required. If you take a simple preventive measure such as “wash your hands,” but convey it in several different ways, the reader of the label could think you mean something different. This is one of the advantages of providing the text for these statements in the revised HCS.

It should be noted that it appears that all of the commenters favoring an alternative of less than full compliance with GHS saw the primary benefits of adopting the GHS would be in facilitating international trade. As has been addressed throughout the PEA, however, OSHA has based the benefits of this action on improved communication to workers and to health and safety managers and logistics personnel resulting in improved safe handling of hazardous chemicals, not on the trade benefits which, while recognized, have not been quantified. Therefore, OSHA believes that any grandfathering or exemption related to this rule would result in some of these parties not obtaining the same level of benefits of increased comprehensibility as workers in other types and sizes of workplaces.

OSHA welcomes comments on these issues, but in the absence of a clear case for one of the alternatives presented, OSHA will continue to consider the alternative proposed, full compliance with GHS by all U.S. firms, the best alternative.

OSHA considered one other set of alternatives to the proposed rule: changing the proposed three-year duration of the phase-in. A shorter phase-in period was criticized by all commenters both because of feasibility issues and for radically increasing compliance costs. OSHA did examine the costs and benefits of a longer phase-in, over a five-year period, and found that the longer phase-in would lower annualized costs from $97 million to $88 million per year, but would also lower the annualize benefits from $851 million per year to $693 million per year, with the ultimate effect of lowering net benefits. Even the lowering of costs may be somewhat illusory because these estimates do not take account of the additional confusion caused by having two different systems in place for an additional two years.

I. Environmental Impacts

The provisions of this proposal have been reviewed in accordance with the requirements of the National Environmental Policy Act (NEPA) of 1969 (42 U.S.C. 4321, et seq.), the Council on Environmental Quality (CEQ) NEPA regulations (40 CFR parts 1500-1508), and the DOL NEPA Procedures (29 CFR part 11). As a result of this review, OSHA has determined that the proposed standards would have no significant adverse effect on air, water, or soil quality, plant or animal life, use of land, or other aspects of the environment. OSHA anticipates that the more complete and easier-to-understand SDSs resulting from this proposal would, in addition to increasing employee health and safety, have positive effects on the environment.

J. Unfunded Mandates Reform Act Analysis

Section 3 of the Occupational Safety and Health Act makes clear that OSHA cannot enforce compliance with its regulations or standards on the U.S. government “or any State or political subdivision of a State.” Under voluntary agreement with OSHA, some States enforce compliance with their State standards on public sector entities, and these agreements specify that these State standards must be equivalent to OSHA standards. Thus, although OSHA may include compliance costs for affected public sector entities in its analysis of the expected impacts associated with a proposal, the proposal would not involve any unfunded mandates being imposed on any State or local government entity.

Based on the analysis presented in this preliminary economic analysis, OSHA concludes that the proposal would impose a Federal mandate on the private sector in excess of $100 million in expenditures in any one year. Accordingly, this preliminary economic analysis of the proposed revisions to the HCS constitutes the written statement containing a qualitative and quantitative assessment of the anticipated costs and benefits of the Federal mandate, as required under Section 202(a) of the Unfunded Mandates Reform Act of 1995 (2 U.S.C. 1532(a)).

K. Sensitivity Analysis

The methodology and calculations underlying the estimation of the compliance costs, benefits, and economic impacts associated with this rulemaking are generally linear and additive in nature. Thus, the sensitivity of the results and conclusions of the analysis will generally be proportional to variations in the relevant input parameters.

For example, if the estimated time that companies need to reclassify chemical hazards and revise SDSs and labels were doubled, the corresponding labor costs (but not software costs) of reclassification and revision of SDSs and labels would double as well.

OSHA evaluated a series of such changes in input parameters to test whether and to what extent the general conclusions of the economic analysis held up. On the whole, OSHA found that the conclusions of the analysis are reasonably robust, as changes in any of the input parameters tend not to produce disproportionately large changes in the results. The results also show significant net benefits for the proposed rule regardless of the individual revisions to costs, benefits, or discount rate. The results of the individual sensitivity tests are summarized in Table VII-8 and are described in more detail below.

In the sensitivity test where OSHA doubled the estimated time that companies need to reclassify chemical hazards and revise SDSs and labels, and estimates of other input parameters remained unchanged, as shown in Table VII-8, the estimated total costs of compliance would increase by $8 million annually, or by about 8 percent, while net benefits would also decline by $8 million, from $754 million to $746 million annually.

BILLING CODE 4510-26-P

BILLING CODE 4510-26-C

In a second sensitivity test, when OSHA increased the estimated total number of affected SDSs addressed by this rulemaking by 50 percent, the corresponding estimated total cost of reclassification and revision of SDSs and labels increased by 50 percent as well. As shown in Table VII-8, if OSHA's estimates of other input parameters remained unchanged, the total estimated costs of compliance would increase by $5.5 million annually, or by about 6 percent, while net benefits would also decline by $5.5 million annually, from $754 million to $748 million annually. [17]

In a third sensitivity test, when OSHA increased by 50 percent the estimated number of employees required to be covered by hazard communication programs and to be trained on GHS, the corresponding estimate of the total costs associated with training employees increased by 50 percent. As shown in Table VII-8, if OSHA's estimates of other input parameters remained unchanged, the total estimated costs of compliance would increase by $22 million annually, or by about 23 percent, while net benefits would also decline by $22 million annually, from $754 million to $732 million annually.

In a fourth sensitivity test, when OSHA doubled the estimated incremental amount of time necessary for training employees on GHS, the corresponding estimate of the total costs associated with training employees also doubled. As shown in Table VII-8, if OSHA's estimates of other input parameters remained unchanged, the total estimated costs of compliance would increase by $44 million annually, or by about 45 percent, while net benefits would also decline by $44 million annually, from $754 million to $710 million annually.

OSHA also performed sensitivity tests on several input parameters used to estimate the benefits of the proposed rule. In one sensitivity test on benefits, OSHA reduced its estimate of health and safety benefits of the proposed rule from 1 percent to 0.5 percent of the benefits estimated for the existing HCS. As shown in Table VII-8, if OSHA's estimates of other input parameters remained unchanged, the total estimated benefits of the proposed rule would decline by $133 million annually, or by about 16 percent, while net benefits would also decline by $133 million annually, from $754 million to $610 million annually.

In a second, parallel sensitivity test on benefits, OSHA increased its estimate of health and safety benefits of the proposed rule from 1 percent to 5 percent of the benefits estimated for the existing HCS. As shown in Table VII-8, if OSHA's estimates of other input parameters remained unchanged, the total estimated benefits of the proposed rule would increase by $1,064 million annually, or by about 125 percent, while net benefits would also increase by $1,064 million annually, from $754 million to $1,818 million annually.

In a third sensitivity test on benefits, OSHA reduced its estimate of savings due to the improved efficiency in creating and revising SDSs under GHS by 50 percent. As shown in Table VII-8, if OSHA's estimates of other input parameters remained unchanged, the total estimated benefits of the proposed rule would decline by $8 million annually, or by about 1 percent, while net benefits would also decrease by $8 million annually, from $754 million to $746 million annually.

In a fourth sensitivity test on benefits, OSHA reduced its estimate of savings due to the improved efficiency of safety and health managers and logistics personnel by 67 percent. As shown in Table VII-8, if OSHA's estimates of other input parameters remained unchanged, the total estimated benefits of the proposed rule would decline by $313 million annually, or by about 37 percent, while net benefits would also decrease by $313 million annually, from $754 million to $441 million annually.

OSHA also examined the effect of a change in the discount rate on the annualized costs and benefits. Changing the discount rate from 7 percent, used in the base case, to 3 percent would have the effect of lowering the costs to $73 million per year and increasing the benefits to $916 million per year. The result, as shown in Table VII-8, would be to increase net benefits by $89 million per year, from $754 million to $843 million per year.

OSHA also considered the sensitivity of its findings that the proposed rule is economically feasible and does not have a significant economic impact on a substantial number of small entities. Since the estimated potential negative impacts of the rulemaking are relatively small, these impacts would remain small even with relatively large changes in the input parameters. For example, even if the total estimated costs of compliance were increased by a factor of five, these costs would still represent less than 0.002 percent of revenues, and no industry or size class would have costs in excess of 5 percent of profits or 1 percent of revenues.

In conclusion, the sensitivity analysis demonstrates that even with relatively large variations in the input parameters, there would not be any disproportionately large changes in the estimates of compliance cost or benefits. Further, even if there were relatively large uncertainties in the estimates of compliance costs and benefits, there would still be a relatively high confidence in OSHA's finding concerning economic feasibility, the certification that the standard will not have significant economic impacts on a substantial number of small firms, and the conclusion that the benefits exceed the costs.

OSHA welcomes input from the public regarding all aspects of this sensitivity analysis, including any data or information regarding the accuracy of the preliminary estimates of compliance costs and benefit and how the estimates of costs, benefits, and economic impacts may be affected by varying assumptions and methodological approaches.

VIII. OMB Review Under the Paperwork Reduction Act of 1995 Back to Top

The proposed modifications to the Hazard Communication Standard would revise existing Hazard Communication collection of information (paperwork) requirements that are currently approved by the Office of Management and Budget (“OMB”) under the Paperwork Reduction Act of 1995 (“PRA-95”), 44 U.S.C. 3501 et seq., and OMB's regulations at 5 CFR part 1320. The Paperwork Reduction Act defines “collection of information” as “the obtaining, causing to be obtained, soliciting, or requiring the disclosure to third parties or the public of facts or opinions by or for an agency regardless of form or format.” (44 U.S.C. 3502(3)(A).) OSHA has submitted the proposed revised Hazard Communication collection of information requirements identified in this NPRM to the OMB for review in accordance with 44 U.S.C. 3507(d).

As part of its continuing effort to reduce paperwork and respondent burden, the Department of Labor conducts a preclearance consultation program to provide the general public and Federal agencies with an opportunity to comment on proposed and continuing collections of information in accordance with the PRA-95 (44 U.S.C. 3506(c)(2)(A)). This program ensures that information is in the desired format, reporting burden (time and costs) is minimal, collections instruments are clearly understood, and OSHA's estimate of burden is accurate. The Department notes that a Federal agency cannot conduct or sponsor a collection of information unless it is approved by OMB under the PRA, and displays a currently valid OMB control number, and the public is not required to respond to a collection of information unless it displays a currently valid OMB control number. Also, notwithstanding any other provisions of law, no person shall be subject to penalty for failing to comply with a collection of information if the collection of information does not display a currently valid OMB control number. OSHA will publish a notice of OMB's action at the final rule stage.

OSHA solicits comments on the modified collection of information requirements and the estimated burden hours associated with these collections, including comments on the following:

○ Whether the proposed collection of information requirements are necessary for the proper performance of the Agency's functions, including whether the information is useful;

○ The accuracy of OSHA's estimate of the burden (time and cost) of the information collection requirements, including the validity of the methodology and assumptions used;

○ The quality, utility, and clarity of the information collected; and

○ Ways to minimize the burden on employers who must comply, for example, by using automated or other technological techniques for collecting and transmitting information.

The title, description of the need for and proposed use of the information, description of the respondents, and frequency of response of the information collections are described below, along with an estimate of the annual reporting burden and cost as required by 5 CFR 1320.5(a)(1)(iv) and 1320.8(d)(2).

Title: Proposed Changes to the Hazard Communications Standard (Globally Harmonized System of Classification and Labeling of Chemicals (GHS)).

Description and Proposed Use of the Collections of Information: The proposed Standard would modify existing information collection requirements that are currently approved under OMB Control Number 1218-0072 (Expiration Date: October 2009). OSHA has submitted the proposed modification of the Hazard Communication Standard to OMB and has requested a new OMB control number addressing the proposed modification. OSHA will maintain OMB approval of the existing collections of information contained in the Hazard Communication Standard, under OMB Control Number 1218-0072.

The proposed revisions to the OSHA Hazard Communication Standard would standardize the hazard communication requirements for products used in U.S. workplaces, and thus provide employees with consistent hazard communication information. Hazard communication is currently addressed by many different international, national, and State authorities. These existing requirements are not always consistent and often contain different definitions of hazards and varying provisions for what information is required on labels and safety data sheets. The proposed revisions would harmonize the U.S. system with international norms and therefore would facilitate international trade. The proposed modifications to the Standard's collection of information requirements include: (1) Revised criteria for classification of chemical hazards; (2) revised labeling provisions that include requirements for use of standardized signal words, pictograms, hazard statements, and precautionary statements; (3) a specified format for safety data sheets; and (4) related revisions to definitions of terms used in the Standard and to requirements for employee training on labels and safety data sheets.

Paragraph (d), “hazard classification,” requires chemical manufacturers and importers to evaluate chemicals produced in their workplaces or imported by them to classify their health and physical hazards in accordance with the Standard. For each chemical, the chemical manufacturer or importer must determine the hazard classes, and the category of each class, that apply to the chemical being classified. Employers are not required to classify chemicals unless they choose not to rely on the classification performed by the chemical manufacturer or importer for the chemical. Chemical manufacturers, importers or employers classifying chemicals must identify and consider the full range of available scientific literature and other evidence concerning the potential hazards. There is no requirement to test the chemical to determine how to classify its hazards. Mandatory Appendix A to § 1910.1200 shall be consulted for classification of health hazards, and Mandatory Appendix B to § 1910.1200 shall be consulted for the classification of physical hazards.

For mixtures, chemical manufacturers, importers, or employers evaluating chemicals must follow the procedures described in Appendixes A and B to § 1910.1200 to classify the hazards of the chemicals, including determinations regarding when mixtures of the classified chemicals are covered by the Standard. A chemical manufacturer or importer of a mixture is responsible for the accuracy of the classification of the mixture even when relying on the classifications for individual ingredients received from the ingredient manufacturers or importers on the safety data sheets.

Paragraph (f) modifies existing label requirements by requiring more specific information. Paragraph (f)(1) requires chemical manufacturers, importers, or distributors to ensure that each shipped container of classified hazardous chemicals leaving the workplace is labeled, tagged, or marked with the following information:

(i) Product identifier;

(ii) Signal word;

(iii) Hazard statement(s);

(iv) Pictogram(s);

(v) Precautionary statement(s);

(vi) Name, address, and telephone number of the chemical manufacturer, importer, or other responsible party; and

(vii) Supplemental information as appropriate.

Information provided under (i) through (v) above must be in accordance with mandatory Appendix C, Allocation of Label Elements, for each hazard class and associated hazard category for the hazardous chemical; prominently displayed; and in English (other languages may also be included if appropriate). In addition, the information in (ii) through (iv) must be located together on the label, tag, or mark.

For containers of hazardous chemicals that do not fall into one of the new hazard classes, (f)(2) requires that the label include the name of the chemical, the name, address, and telephone number of the manufacturer, importer, or other responsible party, and, as supplementary information, a description of the unclassified hazards and appropriate precautionary measures to ensure the safe handling and use of the chemical.

For labels in the workplace, except as provided in paragraphs (f)(8) and (f)(9) of the Standard, employers must ensure that each container of hazardous chemicals in the workplace is labeled, tagged, or marked with either (i) the information specified under (f)(1)(i) through (v) for labels on shipped containers: or, (ii) product identifier and words, pictures, symbols, or combination thereof, which provide at least general information regarding the hazards of the chemicals, and which, in conjunction with the other information immediately available to employees under the hazard communication program, will provide employees with the specific information regarding the physical and health hazards of the hazardous chemical.

OSHA is also proposing to update the language for workplace signs and labels to incorporate the GHS hazard statement and the applicable precautionary statement(s), where required. Most OSHA substance-specific health standards require hazard warning signs, usually for regulated areas, and the language required on the signs varies. With the GHS revision, these standards retain the requirements for specific warning language for specific signs; however, OSHA is proposing to modify the language to be compatible with GHS and consistent throughout the OSHA standards. The GHS classification process for a specific substance as proposed in this revision of the HCS will dictate the hazard warnings and the precautionary statements that will be required on the new GHS-compliant labels. OSHA believes that having signs and labels in the same formats and containing identical warnings for the same health effects will make it far easier for employers and employees to quickly recognize the hazard and the degree of danger of a hazard, thus enhancing communication.

The proposal modifies the requirements for signs and labels found in the Agency's health standards listed below. Since OSHA is providing specific language for signs and for labels on containers of contaminated clothing, waste and debris, the Agency is exempted from taking burden hours and costs for these provisions. (See 5 CFR 1320.2(c)(2) (“Controlling paperwork burden on the public”)). The Agency is taking burden hours and costs for employers to label, tag, or mark each container of hazardous chemicals with either (i) the information specified under (f)(1)(i) through (v) for labels on shipped containers: or, (ii) product identifier and words, pictures, symbols, or combination thereof, which provide at least general information regarding the hazards of the chemicals.

General Industry Back to Top
Asbestos 1910.1001 1218-0133
13 Carcinogens 1910.1003 1218-0085
Vinyl Chloride 1910.1017 1218-0010
Inorganic Arsenic 1910.1018 1218-0104
Lead 1910.1025 1218-0092
Chromium (VI) 1910.1026 1218-0252
Cadmium 1910.1027 1218-0185
Benzene 1910.1028 1218-0129
Coke Oven Emissions 1910.1029 1218-0128
Cotton Dust 1910.1043 1218-0061
1,2-dibromo-3-chloropropane 1910.1044 1218-0101
Acrylonitrile 1910.1045 1218-0126
Ethylene Oxide 1910.1047 1218-0108
Formaldehyde 1910.1048 1218-0145
Methylenedianiline 1910.1050 1218-0184
1,3-Butadiene 1910.1051 1218-0170
Methylene Chloride 1910.1052 1218-0179
Hazard Communication 1910.1200 1218-0072
Construction Industry  
Methylenedianiline 1926.60 1218-0183
Lead 1926.62 1218-0189
Asbestos 1926.1101 1218-0134
Chromium 1926.1126 1218-0252
Cadmiun 1926.1127 1218-0186

Paragraph (g)(2) requires the chemical manufacturer or importer preparing the safety data sheet (SDS) to ensure that it is in English (although the employer may maintain copies in other languages as well), and include the following section numbers and headings, and associated information under each heading, in the order listed (see Appendix D to § 1910.1200—Safety Data Sheets, for the specific content of each section of the safety data sheet).

(i) Section 1, Identification;

(ii) Section 2, Hazard(s) identification;

(iii) Section 3, Composition/information on ingredients;

(iv) Section 4, First-aid measures;

(v) Section 5, Fire-fighting measures;

(vi) Section 6, Accidental release measures;

(vii) Section 7, Handling and storage;

(viii) Section 8, Exposure controls/personal protection;

(ix) Section 9, Physical and chemical properties;

(x) Section 10, Stability and reactivity;

(xi) Section 11, Toxicological information.

Note 1 to paragraph (g)(2):

To be consistent with the GHS, an SDS must also include the following headings in this order:

Section 12, Ecological information;

Section 13, Disposal considerations;

Section 14, Transport information; and

Section 15, Regulatory information.

Note 2 to paragraph (g)(2):

OSHA will not be enforcing information requirements in sections 12 through 15, as these areas are not under its jurisdiction.

(xii) Section 16, Other information, including date of preparation or last revision.

Paragraph (g)(5) requires the chemical manufacturer, importer or employer preparing the safety data sheet to ensure that the information provided accurately reflects the scientific evidence used in making the hazard classification. If the chemical manufacturer, importer or employer preparing the safety data sheet becomes newly aware of any significant information regarding the hazards of a chemical, or ways to protect against the hazards, this new information must be added to the safety data sheet within three months. If the chemical is not currently being produced or imported, the chemical manufacturer or importer must add the information to the safety data sheet before the chemical is introduced into the workplace again.

Paragraph (g)(11) requires that employers ensure the safety data sheets are readily available, upon request, to designated representatives, the Assistant Secretary, and the Director, in accordance with the requirements of 29 CFR 1910.1020(e).

Affected Public: Business or other for-profit.

Number of Respondents: 90,801 firms producing Safety Data Sheets and labels.

Frequency: One time.

Average Time per Response: Time to convert Safety Data Sheets and labels to the new system ranges from 7 hours for establishments having between 1 to 19 employees; to 3 hours for establishments having greater than 500 employees.

Estimated Total Burden Hours: 2,125,414.

Estimated Costs (Operation and Maintenance):$32,055,258.

Submitting comments. Members of the public who wish to comment on the paperwork requirements in this proposal should send their written comments to the Office of Information and Regulatory Affairs, Office of Management and Budget, Room 10235, New Executive Office Building, Washington, DC 20503; Attn: OSHA Desk Officer (RIN 1218-AC20). The Agency encourages commenters also to submit their comments on these paperwork requirements to the rulemaking docket, along with their comments on other parts of the proposed rule. Comments may be submitted by using the Federal eRulemaking portal at http://www.regulations.gov. Comments and submissions are posted without change; therefore OSHA cautions commenters about submitting personal information such as social security numbers and date of birth. Information on using the http://www.regulations.gov Web site to submit comments and access the docket is available at the Web site's “User Tips” link. For instructions on submitting these comments to the rulemaking docket, see the sections of this Federal Register notice titled DATES and ADDRESSES.

Docket and inquiries. To access the docket in order to read or download comments and other materials related to this paperwork determination, including the complete Information Collection Request (ICR) (containing the Supporting Statement (describing the paperwork determinations in detail) and attachments), use the procedures described under the section of this notice titled ADDRESSES. To make inquiries, or to request other information, contact Mr. Todd Owen, Directorate of Standards and Guidance, OSHA, Room N-3609, U.S. Department of Labor, 200 Constitution Avenue, NW., Washington, DC 20210; telephone (202) 693-2222.

IX. Federalism Back to Top

The Agency reviewed the proposed Hazard Communication Standard according to the Executive Order on Federalism (Executive Order 13132, 64 FR 43255, August 10, 1999). This Executive Order requires that Federal agencies, to the extent possible, refrain from limiting State policy options, consult with States before taking actions that restrict their policy options, and take such actions only where there is constitutional and statutory authority to do so and the problem is of national significance. The Executive Order generally allows Federal agencies to preempt State law only where there is clear evidence of Congressional intent to allow it, or where the exercise of State authority would conflict with the exercise of Federal authority under a statute; in such cases, Federal agencies must limit preemption of State law to the extent possible. Section 18 of the Occupational Safety and Health Act (the “Act” or “OSH Act”), 29 U.S.C. 667, expresses Congress' clear intent to preempt State laws with respect to issues for which OSHA has promulgated an occupational safety and health standard under section 6 of the Act. Under section 18 of the Act, a State may avoid preemption only if it submits and obtains OSHA approval of an occupational safety and health plan. See Gade v. National Solid Wastes Management Association, 112 S. Ct. 2374 (1992).

With respect to States that do not have OSHA-approved plans, the Agency concludes that this proposal falls under the preemption provisions of the Act. Additionally, section 18 of the Act prohibits States without approved plans from issuing citations for violations of OSHA standards; the Agency finds that this proposed rulemaking does not expand this limitation. OSHA has authority under Executive Order 13132 to propose a Hazard Communication Standard because the problems addressed by these requirements are national in scope.

Section 18(c)(2) of the Act permits State-plan states to develop their own requirements to deal with any special workplace problems or conditions, provided, inter alia, these requirements are at least as effective as the Federal standards promulgated under section 6 of the Act. Although a State standard becomes effective in accordance with State promulgation provisions, and is enforceable upon promulgation, OSHA must also review and approve the standard to assure that it is “at least as effective” as the Federal standard. OSHA intends to closely scrutinize State hazard communication standards submitted under current or future State plans to assure equal or greater effectiveness, including assurance that any additional requirements do not conflict with, or adversely affect, the effectiveness of the national application of OSHA's standard. OSHA must determine in its review whether any State plan standard provisions that differ from the Federal provisions, when applicable to products distributed or used in interstate commerce, are “required by compelling local conditions and do not unduly burden interstate commerce.” OSH Act section 18(c), 29 U.S.C. 667(c).

X. State Plans Back to Top

The 26 States and territories with their own OSHA-approved occupational safety and health plans must adopt comparable provisions within six months after the Agency publishes a final standard. These States and territories are: Alaska, Arizona, California, Hawaii, Indiana, Iowa, Kentucky, Maryland, Michigan, Minnesota, Nevada, New Mexico, North Carolina, Oregon, Puerto Rico, South Carolina, Tennessee, Utah, Vermont, Virginia, Virgin Islands, Washington, and Wyoming. Connecticut, New Jersey and New York have OSHA approved State Plans that apply to State and local government employees only. Each state-plan State's existing requirements will continue to be in effect until it adopts the required revisions.

XI. Unfunded Mandates Back to Top

Under Section 202 of the Unfunded Mandates Reform Act of 1995, 2 U.S.C. 1532, an agency must prepare a written “qualitative and quantitative assessment” of any regulation creating a mandate that “may result in the expenditure by the State, local, and tribal governments, in the aggregate, or by the private sector, of $100,000,000 or more” in any one year before issuing a notice of proposed rulemaking. OSHA's proposal does not place a mandate on State or local governments, for purposes of the UMRA, because OSHA cannot enforce its regulations or standards on State or local governments. (See 29 U.S.C. 652(5).) Under voluntary agreement with OSHA, some States enforce compliance with their State standards on public sector entities, and these agreements specify that these State standards must be equivalent to OSHA standards. The OSH Act also does not cover tribal governments in the performance of traditional governmental functions, though it does when tribal governments engage in commercial activity. However, the proposal would not require tribal governments to expend, in the aggregate, $100,000,000 or more in any one year for their commercial activities. Thus, although OSHA may include compliance costs for affected governmental entities in its analysis of the expected impacts associated with a proposal, the proposal does not trigger the requirements of UMRA based on its impact on State, local, or tribal governments.

Based on the analysis presented in the Preliminary Economic Analysis (section VII above), OSHA concludes that the proposal would impose a Federal mandate on the private sector in excess of $100 million in expenditures in any one year. The Preliminary Economic Analysis constitutes the written statement containing a qualitative and quantitative assessment of the anticipated costs and benefits required under Section 202(a) of UMRA (2 U.S.C. 1532).

XII. Protecting Children From Environmental Health and Safety Risks Back to Top

Executive Order 13045 requires that Federal agencies submitting covered regulatory actions to OMB's Office of Information and Regulatory Affairs (OIRA) for review pursuant to Executive Order 12866 must provide OIRA with (1) an evaluation of the environmental health or safety effects that the planned regulation may have on children, and (2) an explanation of why the planned regulation is preferable to other potentially effective and reasonably feasible alternatives considered by the agency. Executive Order 13045 defines “covered regulatory actions” as rules that may (1) be economically significant under Executive Order 12866 (i.e., a rulemaking that has an annual effect on the economy of $100 million or more, or would adversely effect in a material way the economy, a sector of the economy, productivity, competition, jobs, the environment, public health or safety, or State, local, or tribal governments or communities), and (2) concern an environmental health risk or safety risk that an agency has reason to believe may disproportionately affect children. In this context, the term “environmental health risks and safety risks” means risks to health or safety that are attributable to products or substances that children are likely to come in contact with or ingest (e.g., through air, food, water, soil, product use). The proposed HCS is economically significant under Executive Order 12866 (see section VII of this preamble). However, after reviewing the proposed HCS, OSHA has preliminarily determined that the standard would not impose environmental health or safety risks to children as set forth in Executive Order 13045.

XIII. Environmental Impacts Back to Top

The Agency reviewed the proposed Hazard Communication Standard according to the National Environmental Policy Act (NEPA) of 1969 (42 U.S.C. 4321 et seq.), the regulations of the Council on Environmental Quality (40 CFR part 1500), and the Department of Labor's NEPA procedures (29 CFR part 11).

As a result of this review, OSHA has made a preliminary determination that the proposed HCS will have no impact on air, water, or soil quality; plant or animal life; or the use of land or aspects of the external environment. Therefore, OSHA concludes that the proposed HCS would have no significant environmental impacts.

XIV. Public Participation Back to Top

OSHA encourages members of the public to participate in this rulemaking by submitting comments on the proposal.

Written Comments. OSHA invites interested persons to submit written data, views, and arguments concerning this proposal. In particular, OSHA encourages interested persons to comment on the issues raised in section II of this preamble. When submitting comments, persons must follow the procedures specified above in the sections titled DATES and ADDRESSES. The comments must clearly identify the provision of the proposal you are addressing, the position taken with respect to each issue, and the basis for that position. Comments, along with supporting data and references, received by the end of the specified comment period will become part of the record, and will be available for public inspection and copying at the OSHA Docket Office as well as online at www.regulations.gov (Docket Number H022K-2006-0062).

Informal Public Hearing. Pursuant to section 6(b)(3) of the Act, members of the public will have an opportunity to provide oral testimony concerning the issues raised in this proposal at informal public hearings. The hearings will be announced in the Federal Register.

XV. Summary and Explanation of the Proposed Standard Back to Top

The advance notice of proposed rulemaking (ANPR) published by OSHA on September 12, 2006 (71 FR 53617) included a series of questions to solicit information on a number of specific topics. The responses from more than 100 commenters have been used by the Agency to help prepare the required analyses for this rulemaking, as well as to make determinations regarding the proposed text. The discussion below on each paragraph of the proposed standard addresses the comments that were related to those subjects, and the discussion on the regulatory impact analysis in Section VII of this preamble refers to responses related to that topic.

In addition to the responses to specific questions in the ANPR, OSHA has also received general comments covering topics such as statements of support for the rulemaking, approaches or principles to follow in the rule, suggestions for outreach and compliance assistance, and other subjects of concern. Before addressing the specific paragraphs of the proposed rule, we would like to discuss these general comments.

Support for the rulemaking. Many of those who responded to the ANPR expressed their support for adoption and implementation of the GHS. The supporters far out numbered those who opposed or questioned adoption (see, e.g., Document ID #s 0003, 0007, 0047, 0050, 0052, 0062, 0106, 0011, 0033, 0038, 0123, 0130, 0151, 0163, and 0171). The reasons presented for this support varied, but included the belief that adoption of the GHS will bring consistency and clarity to hazard communication (e.g., Document ID #s 0046, 0059, 0081, and 0038); will help to ensure that employees have reliable, consistent, comprehensive and comprehensible information (e.g., Document ID #s 0054, 0030, 0037, and 0124); will help to enhance human health and the environment (improved worker safety) (e.g., Document ID #s 0064, 0081, 0032, and 0128); and will reduce burdens associated with preparing multiple classifications and labels for the same product (e.g., Document ID #s 0048, 0080, 0030, and 0123).

Support for implementation of the GHS by OSHA was expressed by both users and producers of chemicals. For example, the Aerospace Industries of America, Inc., representing companies that are generally large users of chemicals, identified many of these benefits in its statement of support (Document ID # 0054):

AIA supports OSHA's current efforts to adopt the GHS and its past participation in the development of the UN's GHS for classification and communication of chemical hazards. We believe that the GHS adoption will help bring consistency and clarity to national and international regulation of hazardous chemicals and will help ensure that employers and employees have reliable, consistent, and comprehensive information on hazardous chemicals in the workplace. With the great diversity in the current systems of hazard communications globally, where MSDSs and chemical labels and classification systems vary in content details and length, type of information, format, and depth of hazard warnings and procedures, there is often inconsistency, redundancy, and incompatibility in labels developed by manufacturers and distributors. This often results in confusion for workers who try to interpret the MSDSs and labels, particularly across differing industry sectors and geographic areas where language, culture, and levels of experience and training may vary. OSHA's proposal to adopt applicable provisions of the GHS into the U.S. workplace is a positive step in working toward developing standardized, uniform, classification, labeling, and related procedures for worker hazard communications systems.

The United Parcel Service, Inc., also a user of chemicals as well as a transporter, supported implementation of the GHS too (Document ID # 0064):

UPS is pleased to support OSHA's adoption of the GHS and applauds the publication of the ANPRM as an important step toward implementation. We believe that the implementation of the GHS has the potential to (1) contribute to the safety of workers through standardized and more easily understood Safety Data Sheets (“SDSs”); (2) streamline domestic hazard classification and labeling across all pertinent U.S. agencies (OSHA, EPA, DOT, CPSC); and (3) facilitate international trade in chemical-based products by harmonizing hazard communication requirements across national borders. UPS also recognizes that the current HAZCOM standard, while not perfect, has helped promote the safety and health of American workers. We believe that OSHA can reap the benefits of the GHS without compromising the substantial benefits of the existing HAZCOM regime.

The American Federation of Labor and Congress of Industrial Organizations (AFL-CIO), representing employees exposed to chemicals in the workplace, also recognized the value of revising the HCS to adopt the GHS provisions (Document ID # 0124):

[T]he GHS offers a standardized and specific approach to the creation of labels and Safety Data Sheets (SDS), with a set format, content and order. Additionally, the GHS has an established set of hazard criteria and employs the use of standardized pictograms. We believe these elements of the GHS, when incorporated into the HCS, will assist greatly in generating labels and SDS's that are vastly more consistent and comprehensible in comparison to the current MSDS's and labels. The improved consistency will also increase the ability to communicate the hazard information to workers. The AFL-CIO fully supports the efforts of OSHA to modify the HCS so that these objectives are realized.

Similarly, DuPont, a major chemical manufacturer, also expressed its support for pursuing harmonization through adoption of the GHS (Document ID # 0038):

DuPont supports OSHA adoption of the GHS and the publication of this ANPRM as a concrete step towards implementation of the GHS in the United States. DuPont urges OSHA to use the information received in response to this ANPRM and move quickly and judiciously to the next step towards a globally harmonized system—publication of a proposed rule. DuPont believes that implementation of the GHS will mean that workers who must handle hazardous chemicals will find hazard information presented in a standardized and more comprehensible manner. DuPont also believes that implementation of the GHS will ultimately reduce the costs to businesses of classifying chemicals as to their hazards and creating warning labels and safety data sheets.

While support for implementation of the GHS was widespread in the comments, these supporters also recognized the challenges associated with implementation. For example, it was noted by a number of commenters that there will be short-term costs associated with implementation, and they urged OSHA to take steps to minimize them by providing a reasonable time period for phase-in, coordinating with other agencies, and providing extensive outreach (see, e.g., Document ID #s 0032, 0111, 0155, 0157, and 0162). As will be addressed in other parts of this preamble, OSHA also recognizes the costs associated with implementation of the changes necessitated by adoption of the GHS, and has taken a number of steps to address them, including those recommended by these and other commenters.

Others were concerned that the GHS is not completely harmonized because it allows countries and agencies within countries, to select from among a collection of building blocks when determining the scope of their requirements (e.g. Document ID # 0076). The GHS was designed in this manner because the existing systems all had scope accommodations for different sectors. For example, the most notable difference among sectors involves transport of dangerous goods and the workplace. In the transport sector, only those hazards which involve the types of exposures expected to be encountered in transport are covered. In the area of health effects, this has been defined as acute health effects, and the transport sector does not include any chronic health hazards in its coverage. Representatives of transport authorities involved in the negotiations indicated that this coverage was considered appropriate, and the building block concept that allowed them to continue to have that scope was necessary to include transport within the GHS. On the other hand, workplace authorities are concerned about chronic health hazards occurring as a result of workplace exposures, and expected the GHS to include those types of effects. Thus the GHS does not specify that all provisions should be applied to all sectors.

However, as will be addressed below in specific paragraphs where this may be a concern, OSHA does not presently preclude employers from including additional information on labels and safety data sheets to address areas that are not covered by OSHA, and would not do so when implementing the proposed revisions. For example, where employers are preparing labels and SDSs for products that will be marketed in both the consumer and the workplace sector, additional information on acute toxicity at lower levels of concern may be included for the consumer sector without violating any current or proposed OSHA requirements. Similarly, information regarding transportation and environmental concerns may be included on SDSs required by OSHA. However, the Agency only enforces the standard with regard to the information required under its own provisions. The same situation would apply in implementation of the proposed revisions.

In addition to those who supported implementation, but raised areas of concern regarding the way in which it is pursued, there were others who did not support implementation (Document ID #s 0004, 0065, 0068, and 0108). These commenters argued that it would be too financially burdensome (Document ID # 0004); delegates power to an international body which can only be accomplished through a treaty, if at all (Document ID # 0065); would change the current hazard communication scheme and thus potentially impair safety (Document ID # 0065); and should not be applied to pesticides because they are already heavily regulated (Document ID # 0108).

With regard to the costs and economic impacts, OSHA has prepared extensive analyses of the costs, benefits, and economic impacts of the rules, which are summarized in Section VII of this preamble. The Agency has preliminarily concluded that the draft proposed standard is an economically significant rule under E.O. 12866 in that the costs exceed $100 million in each of the first three years. However, OSHA will certify that a regulatory flexibility analysis is not necessary under the Regulatory Flexibility Act (RFA), because although the proposed standard will affect a substantial number of small firms, the impacts do not rise to the level of significance that would require a regulatory flexibility analysis under the RFA.

Section VI of the preamble addresses the legal authority of the Agency to pursue this rulemaking. OSHA believes that adoption of the GHS through rulemaking is the appropriate mechanism to achieve this increased protection for exposed employees as well as global harmonization, and that a treaty is not the only means to accomplish this goal. More importantly, however, adoption of the GHS through rulemaking does not delegate “power to an international body” as argued by the National Association of Home Builders (Document ID # 0065). NAHB also argues that the proposal would allow hazard determinations “to be based on something other than fact and scientific evidence.”

This rulemaking process is the legal means to modify the current HCS requirements to make them consistent with GHS. Promulgation of the GHS modifications and implementation of the revised HCS will be by OSHA under the Agency's authority in the OSH Act. No international body will dictate the terms of the adoption. Moreover, there will be no international body with any authority in American workplaces with regard to hazard communication. Furthermore, the hazard determination process under the HCS is currently based on an evaluation of scientific facts and evidence, and would continue to be so under the revised HCS as proposed. The proposed revisions simply provide more extensive guidance on the scientific approach to hazard classification to help ensure a consistent evaluation process by multiple chemical manufacturers. As will be discussed in other parts of this preamble, OSHA believes that adoption of the GHS would lead to increased accuracy and reliability in evaluations of scientific evidence, and thus better information for employers and employees to use to protect them in the workplace.

OSHA believes that arguments presented in this preamble, and the accompanying analyses, indicate that pursuing modifications to the HCS will enhance employee protection, as well as ultimately facilitate compliance for all companies including those in the construction industry that use hazardous chemicals.

Therefore, while OSHA did not include questions regarding the support of stakeholders for adoption of the GHS, it is clear that a majority of those responding to the ANPR support moving forward with the rulemaking. The arguments presented by those few who actively objected to adoption have been addressed in this preamble and the analyses for the rule, and have not been found persuasive. Other issues raised by supporters as concerns or suggestions for addressing concerns, have also been addressed in the proposed rule. While OSHA has addressed many of the identified issues in the proposal, the Agency recognizes that stakeholder input is needed to resolve some of the concerns, and these have been described in Section II.

Other general issues. Commenters also raised a number of other issues related to the rulemaking that were not directed to specific paragraphs of the HCS. Some respondents indicated that OSHA should limit changes to the HCS to those required to align with the GHS, thus keeping the framework of the existing HCS (see, e.g., Document ID #s 0047, 0080, 0104, 0123, 0145, 0163, 0167, and 0170). For example, ORC Worldwide (Document ID # 0123) stated:

* * *[O]SHA can help minimize the cost to businesses by only modifying those sections of the OSHA Hazard Communication Standard (HCS) that must be changed to be consistent with GHS. Therefore, we strongly support OSHA's stated intent to maintain the current scope, application, and interpretations of the HCS, and only modify those sections of the standard necessary for consistency with the GHS. Not only will this help minimize the implementation burden on industry, it should also serve to minimize confusion among employers and employees during the implementation period.

As will be described in greater detail below with regard to specific provisions, OSHA has made every effort to maintain the framework of the current HCS in the proposed revisions. The modifications proposed are believed by OSHA to be those that are required to align the current HCS with the GHS, but do not address provisions of the current standard that are not addressed in the GHS. Thus, for example, the scope and application paragraph remains largely unchanged, as does the paragraph addressing trade secret protection. The primary modifications proposed in these paragraphs are changes in terminology required to ensure consistency.

Many commenters also suggested that OSHA should coordinate implementation of the GHS with other Federal agencies. These included primarily EPA, DOT, and CPSC (see, e.g. Document ID #s 0048, 0050, 0053, 0076, 0104, 0111, 0123, 0134, 0154, 0162, and 0170). Others mentioned the Mine Safety and Health Administration (MSHA) (Document ID #s 0049, 0101, and 0111). For example, the Soap and Detergent Association (Document ID # 0170) stated:

SDA urges OSHA to coordinate implementation of revisions to the HCS related to the GHS with the Environmental Protection Agency (EPA), Department of Transportation (DOT), and the Consumer Product Safety Commission (CPSC), which all have announced their intentions to implement GHS provisions in their regulations. Workplace hazard communication occurs in a stage of the overall life cycle of chemicals and finished products. Coordination and synchronization of implementation timing could greatly improve the efficiency of implementation of the GHS by industry.

OSHA agrees with these commenters that the U.S. government agencies should continue to coordinate their activities with regard to implementation of the GHS. In terms of adopting the GHS provisions, DOT has substantially aligned the criteria for physical hazards in their regulations with those of the GHS under the HM-215I rulemaking (71 FR 78595). EPA and CPSC have not initiated rulemaking on the GHS. Thus at this point, there is little to coordinate in terms of timelines. As rulemaking develops in these Agencies, discussions will continue to take place in the interagency committee on this subject. With regard to MSHA, Department of Labor rulemaking activities are coordinated through Department officials, and MSHA has been apprised of OSHA's activities in order to determine what action may be appropriate for them to pursue in this area.

A number of commenters also argued that OSHA should coordinate implementation with major U.S. trading partners (see, e.g., Document ID #s 0042, 0048, 0101, 0116, 0128, 0141, 0155, and 0170). Similarly, several argued that countries should limit modifications to the GHS that are country-specific, and that the UN process should be used to control such changes (Document ID #s 0042, 0018, 0134, 0154, 0163, 0164, and 0171). For example, the American Petroleum Institute (API) addressed these issues as follows (Document ID # 0171):

API strongly recommends that OSHA ensure that timing and coordination of GHS implementation schedules are in line with those of other countries, allowing sufficient time for companies to organize and accomplish necessary work. In order to achieve international harmonization of hazard communication materials and to avoid undue burden on companies, OSHA must stay engaged with all other actors to encourage even and consistent implementation of GHS by individual countries. Further, API recommends that OSHA work closely with other government agencies and countries to ensure alignment to the UN endorsed version of the GHS. As the implementation of the GHS by countries deviates from the UN version of GHS, the perceived benefits of harmonization substantially decrease.

OSHA agrees with these commenters that coordination among trading partners would enhance harmonization and facilitate implementation. The Agency remains active in the UN process, participating in the Subcommittee of Experts on the GHS, as well as the UNITAR Programme Advisory Group. There is increased emphasis in the Subcommittee on implementation issues as well as coordination. OSHA led a correspondence group that reviewed implementation of the mixture classification provisions, and modifications to address concerns raised were incorporated into Revision 3 of the GHS to help ensure consistency in approach. OSHA will continue to lead a correspondence group on practical classification and hazard communication issues. In addition, the Subcommittee has established a correspondence group to address broader implementation issues, and OSHA is participating in those deliberations as well.

The Agency has also had bilateral discussions in the past with Canada, as well as the European Union (EU), on issues related to implementation. These are two of the key trading partners for the U.S. The EU has recently revised its overall approach to the regulation of chemicals in a new European Community Regulation (EC 1907/2006) referred to as REACH: Registration, Evaluation, Authorization and Restriction of Chemical substances. The new law entered into force on June 1, 2007, and the provisions will be phased in over 11 years. REACH addresses chemical hazards over the life cycle of a chemical, and gives greater responsibility to industry to manage the risks from chemicals and to provide safety information on substances. Manufacturers and importers will be required to gather information on the properties of their chemical substances, which will allow their safe handling, and to register the information in a central database run by the new European Chemicals Agency (ECHA). The Agency will act as the central point in the REACH system: it will manage the databases necessary to operate the system, coordinate the in-depth evaluation of suspicious chemicals, and run a public database in which consumers and professionals can find hazard information.

On September 3, 2008, the EU Parliament completed revisions to its longstanding chemical classification and labeling approach to align with the GHS (referred to now as the European Regulation on the Classification, Labelling, and Packaging of Substances and Mixtures). It applies to substances as of December 1, 2010, and mixtures as of June 1, 2015. The final version was published in the EU Official Journal on December 31, 2008.

In terms of these proposed provisions, OSHA examined the European Commission's regulation to coordinate where possible on approaches to implementation. However, the primary principles followed by OSHA in developing this proposal were to ensure that the modifications maintain or enhance the protections of the current standard, and that the modifications are consistent with the negotiated provisions of the GHS.

One of the issues of concern regarding implementation by some other countries has been deviation from the GHS itself. Because GHS is intended to be globally implemented, efforts by countries to deviate in a collective manner from the GHS, rather than maintaining consistency, defeats the purpose, and consequently, lessens the benefits of the GHS. OSHA will continue to seek opportunities to ensure coordination of implementation and promote harmonization, both internationally and bilaterally.

It should also be noted that the GHS is a living document, and the UN actively reviews it and considers possible changes based on implementation experiences and other information. These changes are made on a two-year cycle, referred to as a biennium. The OSHA proposal is based on Revision 3 of the GHS. Revision 3 was adopted by the UN Subcommittee of Experts on the GHS (UNSCEGHS) in December 2008. A compilation of the approved changes is available on the UN Web site (ST/SG/AC.10/36/Add. 3), and the full text of Revision 3 will be accessible later this year. There are a number of clarifications and small modifications in Revision 3 that address inconsistencies or discrepancies in the previous text of the GHS, and these have been incorporated into this proposal.

It is expected that as the UNSCEGHS fulfills its mandate to ensure that the GHS is up-to-date and relevant, further changes will be adopted on a biennium basis. If the change(s) is substantive and controversial, OSHA will have to engage in notice and comment rulemaking in order to amend the HCS. However, for non-substantive or clarification changes, OSHA has rulemaking options available that can be utilized to implement the changes and can be done more quickly than the full notice and comment rulemaking process.

Two possible means are the Standards' Improvement Process (SIPs) or a Direct Final Rule (DFR). Each of these options also gives the public notice and opportunity to comment, but has the advantage of a faster process. Either method could be used to ensure that the HCS remains current with the GHS.

Outreach/Compliance Assistance. The ANPR included a series of questions to solicit input from the public on what outreach or compliance assistance materials would be appropriate and useful. OSHA received many comments in response to these questions, with a number of creative and interesting suggestions for outreach products. The Agency will use this input to develop an outreach plan and prepare materials for distribution when the rulemaking is completed. In addition, and as suggested by a number of commenters (see, e.g., Document ID #s 0047, 0065, 0081, 0104, 0018, 0025, and 0154), OSHA will continue working with its partners, alliances and other interested parties to examine projects that could be completed by them, or in coordination with them, that could be targeted to specific industries or interest groups.

With regard to the questions on the media through which to distribute materials, all of the methods mentioned in the ANPR received considerable support. In addition, a number of commenters indicated that all types of distribution systems should be used to reach the widest audience, including the Web site, electronic tools, PowerPoint presentations, flash videos, a dedicated web page, mail, train-the-trainer sessions, regional workshops, etc. All of the possible subjects suggested by OSHA (e.g., hazard classification, labels, and safety data sheets) were also endorsed as being of interest.

Many commenters agreed with OSHA that training on understanding pictograms and symbols, as well as hazard statements, signal words, labels, and SDSs, would be useful for both small businesses and employees (see, e.g., Document ID #s 0044, 0061, 0072, 0028, 0034, 0107, 0139, 0163, and 0170). There were also several recommendations that OSHA prepare a poster with the pictograms that can be displayed in workplaces (Document ID #s 0046, 0047, 0064, 0028, 0123, and 0171).

In addition, it was suggested that training on classification procedures, particularly for mixtures, would be useful, as would software that could complete mixture calculations (see, e.g., Document ID #s 0046, 0054, 0032, 0038, 0128, 0140, and 0154). And a number of respondents believe that OSHA should develop a series of training modules on different aspects of the revised HCS (Document ID #s 0047, 0051, 0080, 0025, and 0135), and provide training online (Document ID #s 0059, 0032, 0125, 0129, 0155, and 0157).

Commenters also suggested that OSHA prepare a comprehensive comparison of the current standard to the revised HCS when completed (Document ID #s 0054, 0135, and 0145), as well as a reference table with different requirements around the world (Document ID #s 0047, 0080, 0123, and 0171). It was also noted that materials should be available in multiple languages (Document ID #s 0046 and 0080).

Other ideas presented included electronic seminars (Document ID # 0064); model programs (Document ID #s 0064, 0076, 0080, 0029, and 0124); toolbox talks (Document ID # 0065); Quick Cards (Document ID # 0065); online inventory lists (Document ID #s 0076 and 0178); Q and A document (Document ID #s 0072 and 0160); hotline (Document ID #s 0077, 0104, 0179, 0140, and 0163); GHS resource CD (Document ID #s 0021 and 0155); SDS template (Document ID #s 0144 and 0145); timely compliance directive (Document ID # 0124); and approximate conversion table for classifications (Document ID #s 0145 and 0163).

The proposed standard. The following is a description of the provisions of the proposed standard. Comments received that were related to the proposed provisions are also addressed.

(a) Purpose. The HCS includes a paragraph that states the purpose of the rule. This stated purpose is two-fold. First, the paragraph indicates that the standard addresses assessment of the hazards of workplace chemicals, and the transmittal of that information to employers and employees. It also describes the contents of a comprehensive hazard communication program as being container labeling and other forms of warning, material safety data sheets, and employee training.

The second part of the paragraph addresses the preemption of State or local laws by this Federal standard. It indicates that OSHA is addressing comprehensively the issues described, and thus the standard preempts States, and political subdivisions of States, from addressing these issues except under the authority of a Federally-approved State plan under Section 18 of the OSH Act. While Section 18 applies to every occupational safety and health standard that OSHA promulgates, the HCS raises particular issues because of the nature of the provisions. It requires chemical manufacturers and importers to evaluate the hazards of the chemicals they produce or import, and to prepare labels and material safety data sheets based on those evaluations to transmit hazard information and appropriate precautionary advice to users downstream. This is a unique, but highly appropriate approach for an OSHA standard, as it recognizes that chemical manufacturers and importers are in the best position to assess the hazards of their products and develop appropriate information for labels and SDSs.

There is a national, indeed international, marketplace for industrial chemicals, and thus chemical manufacturers and importers affect commerce within the meaning of the OSH Act and therefore fall under OSHA's jurisdiction. If a State or a political subdivision of a State, were to establish different requirements for labels and safety data sheets, such requirements would have an impact on chemical manufacturers and importers that are not located in that State. This is a burden that the HCS eliminates by establishing national requirements.

The proposed revision to HCS has essentially the same purposes, and OSHA is proposing only minor modifications to this paragraph. Paragraph (a)(1)would change the language regarding the assessment of hazards to indicate that the hazards will be “classified” rather than simply assessed or evaluated. This is consistent with the approach in the GHS. In addition, OSHA is proposing to modify this paragraph to clearly indicate that the standard is intended to be consistent with the GHS, Revision 3. That change is a reflection of the purpose of this rulemaking to harmonize the existing requirements with the provisions of the GHS, which is the international instrument that includes globally harmonized provisions on hazard communication. In addition, in this paragraph and succeeding paragraphs of the revised rule, the term “material safety data sheet” has been modified to “safety data sheet” to reflect the terminology of the GHS.

The only modifications proposed to paragraph (a)(2) also address terminology, using “classifying” instead of “evaluating”, and “safety data sheet” instead of “material safety data sheet”.

There were no specific comments received in response to the ANPR regarding the Purpose paragraph of the HCS. One comment suggested that the standard should be limited to a purpose of international communication so as not to trigger hazard assessments under other OSHA standards that address respiratory protection, personal protective equipment, or process safety management (Document ID # 0049). There were several other comments that indicated that new assessments would have to be done for these standards (Document ID #s 0178, 0111, 0134, and 0164). Arguments were made that this would lead to extensive additional costs for new engineering controls, respirators, or other personal protective equipment.

As discussed above, there is no identified link to these other standards in the stated purpose of the HCS either currently or with the proposed modifications. While the HCS itself requires the provision of information on recommended control measures, including respiratory protection, personal protective equipment, and engineering controls, there is no requirement for employers to implement the recommended controls. All information available to an employer when designing an appropriate protective program must be used, but a recommendation on a safety data sheet by itself would not trigger the need to implement new controls.

Furthermore, these comments seem to imply that there will be major changes in the hazards of chemicals based on implementation of the GHS provisions. Both the HCS and the GHS are based on identifying and communicating the inherent hazards of chemicals. Thus the biggest change for most chemicals under the proposal will be in categorizing the chemical's hazards. Under the current standard, for example, a chemical either is, or is not, a carcinogen. Under the revised HCS, if a chemical is a carcinogen, it would be categorized as a Category 1 or a Category 2 carcinogen. Such a change would not generally result in a need to change engineering controls or respiratory protection.

It is possible that a chemical may be classified under the proposal as having a hazard it did not have before, but OSHA believes that this is not likely to happen frequently given the broad coverage of the current rule. Furthermore, the physical and chemical characteristics of the chemical—which affect the types of protection required—would not be changed as a result of this proposal. OSHA believes that these revisions would result in few, if any, changes in protective measures required under other OSHA standards.

Several commenters noted what they believed to be the continued need to address the preemption of State standards (see, e.g., Document ID #s 0048, 0056, 0080, 0178, 0036, 0123, and 0135). In addition, commenters also noted that the impact of GHS adoption on State and local laws should be considered in the process (for example, California Proposition 65), and that differences between such laws and the revised HCS should be discouraged (Document ID #s 0042, 0072, 0015, and 0038).

It was also indicated that changes in State laws should be coordinated with the Federal changes to facilitate implementation (Document ID # 0146). See Section IX and X of this preamble for a comprehensive discussion regarding Federalism and State plans.

(b) Scope and Application. The HCS is a generic standard that has very broad provisions in terms of chemicals addressed and workplaces covered. It also interfaces with a number of requirements of other Federal agencies that address labeling of chemical hazards. Paragraph (b) thus includes all of the practical modifications the Agency has developed to ensure that employers and employees understand how the standard is to be applied, and to accommodate various circumstances that potentially affect the application of the standard.

The provisions of paragraph (b)(2) in the HCS address the overall scope of the standard as applying to “any chemical which is known to be present in the workplace in such a manner that employees may be exposed under normal conditions of use or in a foreseeable emergency.” This provision addresses many questions that are raised about the application of the standard. There was one comment received regarding this paragraph which indicated that hazard classification and labeling of steel for chronic health effects should not result from welding being considered a normal condition of use (Document ID # 0160). OSHA has made it clear in past interpretations of the rule that where such products are intended to be welded, this information must be provided for hazard communication purposes. That interpretation does not change as a result of the proposed provisions in the revised rule.

In general, OSHA does not expect significant changes in the chemicals covered by the HCS under the proposed revisions as compared to the current standard. The scope of hazards covered by the GHS is very similar to what is covered by the current HCS. Additional chemicals may be considered to be acutely toxic due to the proposed adoption of Category 4 in acute toxicity which would expand the criteria for inclusion from the current definition (see the discussion under “Hazard classification”). However, these chemicals are already covered under the voluntary national industry consensus standard on precautionary labeling of industrial chemicals (ANSI Z129) that many manufacturers follow in their labeling programs, as well as being covered in the requirements that apply to chemicals shipped to the EU. Thus many manufacturers are already classifying and labeling these chemicals as acute toxins. The proposal is also likely to cover fewer mixtures as acute toxins than the current rule given the hazard classification approach in the GHS that uses a calculation based on proportionality to determine whether a mixture is covered, rather than a strict percentage cut-off of 1%. Other definitions of health hazards would maintain the current broad HCS scope.

In addition to the overall scope statement, the HCS provides for limited coverage in workplace situations that have special circumstances, including laboratories and work operations where employees only handle chemicals in closed containers.

OSHA also addresses the interface with other Federal agency requirements by either exempting the products covered from additional OSHA labeling (such as pesticides required to be labeled by the EPA), or completely exempting the product (such as hazardous waste regulated by EPA). These accommodations help to ensure that Federal requirements do not conflict or duplicate each other.

Under the GHS, such provisions are left under the purview of the “competent authority”. In developing the GHS, it was recognized that countries' regulatory authorities would need to have the discretion to address such national circumstances in ways that are suited to the regulatory perspective of the country. Thus authorities such as OSHA are free to make determinations about scope and application issues while still being harmonized with the primary provisions of the GHS.

OSHA has reviewed the current provisions of paragraph (b), and has determined that no significant changes are required to be consistent with the GHS. Several minor changes to revise terminology are proposed (involving the terms “classifying” and “safety data sheets”), but OSHA is not proposing to modify any of the remaining provisions of paragraph (b). The Agency is also deleting Appendix E of the current HCS, which was guidance for application of the standard, and thus is deleting the reference to it in paragraph (b)(1). As is discussed elsewhere in this preamble, new outreach and compliance assistance materials are being prepared to replace this appendix and other existing outreach materials.

Several commenters indicated that OSHA should adopt exemptions included by the European Union in its requirements. Specifically, these exemptions address non-isolated intermediates, chemicals involved in research and development, and waste (Document ID #s 0049, 0134, and 0164). All of these situations are already addressed in paragraph (b), and OSHA does not believe it is necessary to change them.

In terms of non-isolated intermediates, the overall scope provision in paragraph (b)(2) adequately addresses this situation. This was specifically addressed in the preamble to the 1983 final rule (48 FR 53335):

That is, the term “known” means the employer need not analyze intermediate process streams, for example, to determine the presence or quantity of trace contaminants. However, where the employer knows of such contaminants, and they are hazardous, then they fall under the provisions of the standard.

With regard to chemicals involved in research and development, paragraph (b)(3) limits coverage in laboratories, and partially addresses this situation. Where there is no knowledge of the hazards of such chemicals, the HCS does not apply at all since there is no requirement to generate new hazard information. Where information is available, it must be provided to exposed employees, consistent with paragraph (b)(3) when it is in a laboratory situation. Therefore, it appears to OSHA that this situation is also adequately addressed under the current provisions. Hazardous waste as regulated by EPA is already exempted under paragraphs (b)(6)(i) and (ii).

There were commenters who suggested that OSHA maintain current exemptions or limitations in the revised GHS, including the consumer product exemption (Document ID # 0064), guidance on byproducts (Document ID # 0064), the relative roles of manufacturers and employers (Document ID # 0064), and the article exemption (Document ID # 0160). OSHA agrees and all of these accommodations remain the same in the proposed revised rule. As indicated in the ANPR, the Agency does not intend to change those parts of the HCS that are not affected by the GHS.

One commenter indicated that the revised HCS should indicate that it does not apply fully to State prison inmates because the GHS information would give them data that could be used illegally, and perhaps lead to harm (Document ID # 0069). Generally speaking, State prison inmates are not directly subject to Federal requirements under OSHA, although such requirements may be applied to them under State laws or the provisions of another Federal agency. This comment regarding limitations needed for inmates should be addressed in those jurisdictions, but nothing in these revisions would substantially change the application of the HCS to them.

There were also a few comments regarding the scope of the revised rule in terms of provisions of the GHS that affect the environment or transportation (see, e.g., Document ID #s 0072 and 0179). As OSHA indicated in the ANPR, it does not have the authority to require information in these areas since they are not directed to the protection of employees under its jurisdiction. However, OSHA does not prohibit this type of information on labels or safety data sheets, and is aware that it is often included on labels and safety data sheets currently developed to comply with the HCS. OSHA expects that chemical manufacturers will, in fact, continue to voluntarily include such data on their labels and safety data sheets to meet the requests of their domestic and international customers.

(c) Definitions. This paragraph in the HCS includes the terminology used with the corresponding definitions. Comprehension of the appropriate definitions is critical to understanding the provisions of the standard. In some cases, terms are defined somewhat differently than when used in other contexts, so familiarity with the standard's definitions is important.

In the proposed revisions, OSHA has retained as many definitions as possible from the current HCS. Changes are proposed only when there is a new term used that needs to be defined, or there is a different definition in the GHS, and consistency with the international definition is needed for harmonization purposes. As with the preceding paragraphs, minor modifications have been proposed to ensure terminology is appropriate—primarily the use of terms related to classification and safety data sheets.

One important difference between the HCS and GHS in terminology involves the use of the term “chemical.” The HCS has used this term since it was originally promulgated, and defines it to include elements, chemical compounds, and mixtures of elements and/or compounds. It has been a convenient way to describe the coverage of the rule. The GHS, like some other international standards, uses the terms “substance” and “mixture”. OSHA has decided to maintain a definition of “chemical” in the revised standard, which minimizes the number of terminology changes that have to be made to the regulatory text, as well as providing a shorthand way to define the scope to include both individual substances and mixtures of substances. This term is used in the body of the proposed regulatory text, similar to the use of it in the current HCS. However, the proposed modifications also include definitions for “substance” as well as “mixture” to align with the GHS, and both of these terms are used as well. In particular, in the appendixes that are adopting GHS language, the separate terms “substance” and “mixture” are used consistent with the GHS.

“Substance” means chemical elements and their compounds in the natural state or obtained by any production process, including any additive necessary to preserve the stability of the product and any impurities deriving from the process used, but excluding any solvent which may be separated without affecting the stability of the substance or changing its composition.

A “mixture” is defined as a “combination or a solution composed of two or more substances in which they do not react.” This is consistent with the GHS definition—and while slightly different than the definition in the current HCS, means the same thing.

OSHA is also proposing to maintain the term “hazardous chemical” as used in the current standard (a chemical which is a physical or health hazard), except to add the term “classified” to indicate how it is determined that it is a physical or health hazard, and to add the coverage of unclassified hazards as those terms are defined in a new definition explained below. This term will be used throughout the standard to indicate that the classification process is completed, and the chemical manufacturer has determined that the chemical poses a hazard—either by meeting the requirements for a physical or health hazard or by virtue of being considered an unclassified hazard under this section. Most of the substantive requirements of the rule apply to hazardous chemicals.

Another proposed modification to the definitions paragraph is to move the physical hazard definitions to an appendix. In the current HCS, health hazard definitions are addressed specifically in Appendix A to the rule, but the physical hazard definitions were included in paragraph (c). In the proposed revisions, health hazard definitions will continue to be addressed in Appendix A, but a new Appendix B will address physical hazards. Both of these appendixes will be discussed below under the summary and explanation of “Hazard Classification.”

As noted in Section III above, the physical hazard definitions in the GHS are drawn from the United Nations' Recommendations on the Transport of Dangerous Goods. Since DOT has adopted this international approach, the GHS definitions are substantially harmonized with the U.S. requirements for labeling of dangerous goods in transport. All chemicals that are shipped in the U.S. have already been classified according to DOT's physical hazard definitions. This will reduce the burdens associated with classifying physical hazards under the revised HCS. The primary differences involve exceptions that make the definitions more applicable to workplace situations (for example, coverage of flammable liquids that are currently defined as combustible under the HCS). Modifying the HCS to align with the GHS thus serves the purpose of harmonizing many of these definitions domestically, and results in shippers only having to classify their chemicals once for most physical hazards.

OSHA is proposing to add a definition for the term “classification” in order to ensure that the meaning of this term is clear. Consistent with the definition of classification in the GHS, the proposed definition of “classification” is “to identify the relevant data regarding the hazards of a chemical; review those data to ascertain the hazards associated with the chemical, and decide whether the chemical will be classified as hazardous, and the degree of hazard where appropriate, by comparing the data with the criteria for health and physical hazards.” This definition is very similar to the process of hazard determination that is currently in the HCS, with the exception of determining the degree of hazard where appropriate. This reflects the GHS approach of having categories for each class of hazard. Under the current HCS, there are some definitions that have categories in a hazard class (e.g., acute toxicity, flammability), but other definitions are simply one category (e.g., carcinogenicity). The additional breakdown in the GHS of classes into categories that reflect different severities or levels of effect will provide both employers and employees with more precise information to understand the hazards, to consider when evaluating workplace conditions to determine the risks in the workplace, and to respond to exposure incidents.

In addition to the definition of classification, OSHA has proposed a definition for “hazard class” and “hazard category” to further explain the approach of breaking down the hazardous effects into levels of severity. A “hazard class” is defined as “the nature of the physical or health hazards, e.g., flammable solid, carcinogen, acute oral toxicity.” The definition of “hazard category” is “the division of criteria within each hazard class, e.g., oral acute toxicity and flammable liquids include four hazard categories. These categories compare hazard severity within a hazard class and should not be taken as a comparison of hazard categories generally.” These definitions are also taken from the GHS.

OSHA is proposing to modify the term “health hazard” to reflect the specific hazards defined in the GHS. While the overall scope of what is covered is expected to be essentially the same as the current HCS, the hazards may be identified slightly differently. For example, the current HCS covers reproductive toxicity as a target organ effect, and includes all aspects of the effect under that hazard. The GHS has a separate definition for germ cell mutagenicity, which is considered part of reproductive toxicity in the current HCS. The definition of “health hazard” is thus proposed to be “a chemical which is classified as posing one of the following hazardous effects: acute toxicity (any route of exposure); skin corrosion or irritation; serious eye damage or eye irritation; respiratory or skin sensitization; germ cell mutagenicity; carcinogenicity; reproductive toxicity; specific target organ toxicity (single or repeated exposure); or aspiration toxicity. The criteria for determining whether a chemical is classified as a health hazard are detailed in Appendix A, Health Hazard Criteria.”

A revised definition of “physical hazard” is also proposed to reflect the physical hazards covered in the GHS. While these are similar to the coverage of the HCS, they are in some cases described somewhat differently. The definition proposed for “physical hazard” is “a chemical which is classified as posing one of the following hazardous effects: explosive; flammable (gases, aerosols, liquids, or solids); oxidizer (liquid, solid or gas); self-reactive; pyrophoric (liquid or solid); self-heating; organic peroxide; corrosive to metal; gas under pressure; or water-activated flammable gas.” In addition, the definition refers to Appendix B, Physical Hazard Criteria, for details.

The definition of “label” in the GHS is slightly different than what is currently in the HCS, and OSHA is proposing to modify the HCS to be consistent. Thus the proposed definition of “label” is “an appropriate group of written, printed or graphic information elements concerning a hazardous chemical that is affixed to, printed on, or attached to the immediate container of a hazardous chemical, or to the outside packaging.” The GHS label is more specific than what is required in HCS, and includes certain core information that must be presented. Thus a definition for “label elements” is also proposed, and it would mean “the specified pictogram, hazard statement, signal word, and precautionary statement for each hazard class and category.” “Safety data sheet (SDS)” is defined as “written or printed material concerning a hazardous chemical which is prepared in accordance with paragraph (g) of this section.”

Definitions for terms that describe information required to be provided on labels are also proposed to be added to the HCS. These include “hazard statement”, “pictogram,” “precautionary statement,” “product identifier,” and “signal word.” These proposed new definitions will help to clarify the specific requirements for labels under the revised HCS, and are consistent with similar definitions in the GHS.

“Hazard statement” is “a statement assigned to a hazard class and category that describes the nature of the hazards of a chemical, including, where appropriate, the degree of hazard.” This is essentially what is defined as a hazard warning under the current rule. An example of a hazard statement under the GHS is: Causes serious eye damage. These statements have been codified, meaning that numbers have been assigned to them. They are available in all of the official languages of the United Nations, and thus translation will not be a problem when shipping to countries using those languages. Having standardized statements is expected to facilitate translation into other languages as well.

“Pictogram” means a “composition that may include a symbol plus other graphic elements, such as a border, background pattern, or color, that is intended to convey specific information about the hazards of a chemical.” This definition covers both pictograms in the transport sector, and those in other sectors covered by the GHS. The pictograms are required as part of the core information provided on a label to describe the hazards of a chemical. The workplace pictograms will be a black symbol on a white background with a red diamond border frame. Some commenters noted that the frame should be permitted to be black for domestic shipments as allowed under the GHS (see, e.g., Document ID #s 0032 and 0163). However, as described in Section V of this preamble, there are clear benefits associated with the use of the red frame in terms of recognition and comprehensibility. Thus OSHA is proposing to only allow the red frame to be used, whether the shipment is domestic or international.

Under the GHS, a symbol is generally assigned to each hazard class and category. There are nine agreed symbols under the GHS to convey the health, physical and environmental hazards. Eight of these symbols are proposed for adoption in this rulemaking, the exception being the environmental symbol. Six of these symbols have been used for many years in the international transport requirements, so some employees will already be familiar with them.

The “precautionary statement” is “a phrase that describes recommended measures that should be taken to minimize or prevent adverse effects resulting from exposure to a hazardous chemical or improper storage or handling.” The precautionary statements specified in Appendix C will be required on containers under the revised HCS. An example of a precautionary statement is “wear protective gloves.” The precautionary statements in the GHS are assigned to certain hazard classes and categories. Precautionary statements have not previously been required under the HCS, although many chemical manufacturers include them on their labels for safe handling and use. These statements are codified under the GHS, meaning that numbers have been assigned to them. The precautionary statements in the GHS are not harmonized like the hazard statements are, and the regulatory authority is free to use the statements in the GHS annex or to use alternative statements when adopting the current version of the GHS. Using the GHS statements has the advantage of adopting statements that have undergone expert review by the Subcommittee, are assigned to the appropriate hazard class and category, and have been translated into six languages. Work continues on them in the Subcommittee to combine or edit the precautionary statements to reduce repetition and complexity of the label. The precautionary statements may be considered harmonized in the future. Other countries are already using them (e.g., in Europe). Since OSHA did not previously require the use of precautionary statements, and had no such recommended statements to provide, the Agency has decided to use those currently in the GHS as the mandatory requirements. This will make it easier for compliance since chemical manufacturers and importers will not need to develop, maintain, and translate precautionary statements on their own. It will also help employees since they will be seeing the same language on labels regardless of the supplier of the chemical. Such standardization improves comprehension, and thus the effectiveness of the information transmitted under the standard.

Container labels will also be required to include a “product identifier.” The proposed definition for this term is “the name or number used for a hazardous chemical on a label and in the SDS. It provides a unique means by which the user can identify the chemical. The product identifier used shall permit cross references to be made among the required list of hazardous chemicals, the label, and the SDS.” In other words, the product identifier is essentially the same as the “identity” under the current HCS. The GHS allows competent authorities for workplace requirements to choose not to require specific chemical identities of ingredients to be listed on the label, as long as they are on the SDS. This is the approach OSHA currently uses in the HCS, and it has been effective. OSHA will continue to require chemical identities only on SDSs, and has proposed a definition for “product identifier” that is consistent with the current definition for “identity” to maintain this approach.

Another new concept being proposed for HCS labels is inclusion of a “signal word” to bring attention to the hazardous effects, as well as to contribute to the recognition of the severity of the hazard. Signal words have been used for many years in the United States on consumer and pesticide labels. The proposed definition is “a word used to indicate the relative level of severity of hazard and alert the reader to a potential hazard on the label. The signal words used in this section are ‘danger’ and ‘warning.’ ‘Danger’ is used for the more severe hazards, while ‘warning' is used for the less severe.”

OSHA is proposing to add a definition to the HCS for “unclassified” hazards. As has been noted, the current HCS is performance-oriented, and takes a very broad approach to defining hazards covered by the rule. The GHS is similarly broad in approach, but includes very specific definitions of criteria to apply when determining whether a chemical poses a physical or health hazard. This specification approach has significant benefits associated with it, including providing more guidance to help ensure a consistent approach to determining hazards. It also allows more information to be developed that provides an indication of the severity of effect.

In the ANPR, OSHA asked for comment on whether these criteria are sufficient to cover the hazards present in the workplace. While the Agency believes the scope of coverage is similar between the two approaches, OSHA wants to be sure that the new approach is as comprehensive as the existing standard. The primary hazard addressed by respondents to this question was combustible dust. As will be discussed later in this preamble, OSHA has proposed that the United Nations add criteria for combustible dust to the GHS, so this issue should be resolved in the future by having the necessary criteria. Another potential example is simple asphyxiation. The only specific reference to this effect in the GHS is in the part of the SDS that covers hazards that do not result in classification—suffocation is listed as an example. The definition of “unclassified hazard” could be used in this situation as well. Alternatively OSHA is considering proposing a definition and label elements as discussed in the issues section.

It is possible that there are other hazards that may not yet be specifically defined. The addition of the definition for unclassified hazards is intended to address these situations. Where a classifier has identified evidence of a hazard, but the evidence does not meet the currently specified criteria for hazards covered by the rule, the definition for unclassified hazards will capture those hazards to ensure that the modified HCS is appropriately protective, and covers all of the hazards covered by the current rule. During the negotiations for the GHS, U.S. industry representatives often raised the issue of ensuring that they could provide additional hazard information in order to satisfy product liability laws in the U.S. This was the rationale for allowing such information to be included on labels under supplementary information, and on SDSs under Section 2. Addition of the definition of “unclassified hazards”, and specific recognition of the need to provide information when such effects arise, should help U.S. industry address its product liability concerns as well as protect exposed workers.

OSHA would require the chemicals posing unclassified hazards to be treated as hazardous chemicals under the rule. The Agency anticipates that this information would appear in Section 2 of the SDS (Hazard Identification)—the GHS already identifies this as the appropriate place in its guidance on the contents of SDSs (A4.3.2.3, Other hazards which do not result in classification), and it is included in Appendix D of this proposal as unclassified hazard. In terms of labeling, there would be no specified label elements for chemicals that pose unclassified hazards. The label for such hazards must describe the hazardous effects under supplementary information on the label, as well as provide any appropriate precautionary information. OSHA also expects that such hazards would be addressed in worker training programs.

The Agency anticipates that there will be relatively few situations where there will be scientific evidence or data indicating a hazard that is not currently classified, but wants to ensure that this information is captured and conveyed to employers and employees. It appears that it would also be appropriate to establish a feedback mechanism so in the future, classifiers can inform OSHA of these situations where the current criteria are insufficient, and the Agency can then suggest to the United Nations that appropriate criteria be developed and added to the GHS. This is consistent with the overall approach to hazard classification in the GHS that OSHA is proposing to adopt—that specific criteria be provided to help ensure that classification is appropriate, and information transmittal is consistent from company-to-company. Therefore, the use of the definition of unclassified hazard should be a temporary situation for these hazards, ensuring information is provided until such time as the criteria are added to the rule. OSHA is requesting additional input on this approach in the issues section.

OSHA is not proposing to revise the other terms currently defined in the HCS. In addition, the GHS includes a number of definitions that did not appear to be necessary for inclusion in the revised HCS and as a result have not been addressed here.

(d) Hazard classification.

Hazard determination under the current standard. Under the existing HCS, chemical manufacturers and importers are required to evaluate the scientific data available regarding the chemicals they produce or import, and determine whether they are hazardous within the meaning of the standard. This requires a thorough search of the scientific literature on both the health and physical hazards that the chemical may pose. The identified information must be evaluated within the parameters established in the standard to determine whether the chemical is considered to pose a hazard. Paragraph (d), Hazard determination, provides the regulatory approach for evaluation. This is to be implemented using the definitions provided in paragraph (c), as well as in Appendix A, which provides further elaboration on the nature and breadth of health hazards covered. Appendix B provides additional requirements for identifying and evaluating data regarding hazards. Both of these appendixes are mandatory.

In order to ensure the broadest dissemination of information, and to reduce the number of situations where conflicting determinations may be made for the same chemical by different suppliers, the HCS considers one study, conducted according to established scientific principles and producing a statistically significant result consistent with the definitions of hazard in the standard, to be sufficient for a finding of health hazard under the rule. See 29 CFR 1910.1200(d)(2) and Appendix B. This approach was the broadest among those systems that were used as the basis for the development of the GHS.

Most of the definitions under the HCS simply lead to a conclusion that the chemical involved poses that hazard or it does not. For example, a chemical might be found to be a carcinogen under the rule based on one study indicating that it poses a carcinogenic effect. The current standard does not generally address the degree of severity of the hazardous effect in most of the definitions—so a chemical is either a carcinogen, or it is not. However, while a one study determination leads to providing information about that hazardous effect on a safety data sheet, it may not lead to a hazard warning on a label. The HCS requires such warnings to be “appropriate”, and there are situations where the data do not support warning about the hazard on the label because of other negative studies or information. See 29 CFR 1910 (f)(1)(ii). Thus there is consideration of the weight of evidence when deciding what to include on a label. Chemical manufacturers and importers may also review the weight of evidence in preparing SDSs, and are permitted to discuss negative evidence and other constraints when reporting the information. Under the current standard, OSHA expects the hazard evaluation process to go beyond simply identifying one study, and includes a complete evaluation of all of the information available when determining what information to transmit to users of the chemical.

This hazard evaluation process is consistent with product stewardship processes that have evolved in the chemical industry. (See, e.g., the Responsible Care® program implemented by chemical manufacturers.) Under such processes, chemical manufacturers develop and maintain thorough knowledge of their chemicals. This knowledge is critical to the safe handling and use of the chemicals in their own facilities, as well as in their customers' facilities. It is also critical to handling product liability concerns for their materials.

The HCS requires chemical manufacturers to remain vigilant regarding new information about their chemicals, and to add significant new information about hazards or protective measures to their hazard communication documents within three months of learning about them. See 29 CFR 1910.1200(f)(11), (g)(5). This has always been seen by OSHA as a more rigorous, but essential, requirement than some other countries' provisions, which only require these documents to be reviewed every few years. It should be noted that OSHA has not been enforcing the current requirement to change labels within three months of getting new information. This stay on enforcement began some years ago when the standard was first promulgated, and involved concerns about existing stockpiles of chemicals and other related information. OSHA is proposing to reinstate the requirement and lift the stay, making the updating period consistent with that required for safety data sheets, and invites comments on this issue.

At the time the HCS was promulgated, the standard's provisions and approach were quite novel, and there were concerns that chemical manufacturers and importers would need more guidance regarding what chemicals to consider hazardous. Thus OSHA included provisions in the hazard determination paragraph that established certain chemicals as being hazardous. Chemical manufacturers and importers still had to complete a hazard evaluation and determination of what hazards were posed, but for these designated chemicals, there was no decision to be made as to whether they were hazardous or not. These chemicals were considered to be a “floor” of chemicals covered by the rule, and included those for which OSHA has permissible exposure limits in 29 CFR part 1910, as well as those for which the American Conference of Governmental Industrial Hygienists (ACGIH) has recommended Threshold Limit Values (TLVs). In addition, given that carcinogenicity was the most controversial and difficult health effect to address, OSHA indicated that at a minimum, chemicals found to be carcinogenic in the National Toxicology Program's Annual Report on Carcinogens, or in monographs published by the International Agency for Research on Cancer, were to be considered to be carcinogens in addition to those regulated by OSHA as carcinogens.

The existing HCS also includes provisions regarding hazard determinations for mixtures. 29 CFR 1910.1200(d)(5). Where such mixtures have been tested to determine their hazardous effects, the data on the mixture as a whole is used. Where testing has not been done, OSHA promulgated an approach based on the percentage of a hazardous chemical in a mixture to determine if the mixture is hazardous. Therefore, if a mixture contains one percent or more of a chemical determined to present a health hazard, the mixture is assumed to have the same effect. The one exception is carcinogens—a mixture is considered to be carcinogenic if it contains 0.1% or more of a chemical found to be carcinogenic.

In all cases, a mixture will still be considered to be hazardous if there is evidence that it poses a health risk when the hazardous chemical is present in concentrations below the cut-offs. This was included to ensure that chemicals that can have effects at very low concentrations, such as sensitizers, will be adequately addressed.

For physical hazards, the evaluator must determine based on whatever objective evidence is available whether the hazardous effect is still possible in smaller concentrations. This recognizes that for physical effects, such a determination may be made based on factors such as dilution, and there are readily available means to make an appropriate assessment.

The approach in the existing HCS is considered to be a self-classification system. In other words, the chemical manufacturer or importer reviews the available information, and makes the determination as to whether the product presents a potential hazardous effect. This is different than some other systems where the regulatory authority makes the determination, and publishes a list of hazardous chemicals that must be used by the chemical manufacturer or importer.

The hazard determination is to be completed based on available information. The HCS does not require testing of chemicals to produce information where it is not available.

The hazard determination approach in the HCS recognizes that information about chemicals changes, new chemicals are introduced, others cease to be used—in other words, the world of chemicals in the workplace changes constantly, and the standard is designed to ensure that employees receive the most up-to-date information available regarding the chemicals to which they are currently being exposed.

Employers who simply use chemicals, rather than producing or importing them, are permitted to rely on the information received from their suppliers. 29 CFR 1910.1200(d)(1). This downstream flow of information recognizes that the chemical manufacturers and importers have access to information about the chemicals they sell that is not available to those who only use them. It also reduces duplication of effort by focusing the hazard determination process at the source, rather than having everyone who uses a chemical trying to complete such a process.

The HCS requires chemical manufacturers and importers to maintain a copy of the procedures they follow to make hazard determinations. 29 CFR 1910.1200(d)(6). If OSHA finds errors in a label or SDS, the chemical manufacturer or importer that prepared the document will be held responsible—not the employer using the chemical.

The hazard determination procedures in the HCS, including the definitions and Appendixes A and B, have been in place since the standard was promulgated in 1983. Therefore, the intent to design an approach that was dynamic and would remain current through changes in the workplace appears to have been accomplished.

Hazard Classification under the GHS. The challenge in negotiating an international approach was to create a system that did not require frequent changes yet remained current and protective, incorporating the best parts of the approaches in the existing systems. The GHS embodies an approach that is very similar to the existing HCS in scope and concept, but builds in additional details and parameters to help to ensure consistency worldwide. Like the HCS, the GHS approach is based on a downstream flow of information from suppliers to users; self-classification; use of available information with no new testing; and a broad approach to definitions of hazard. The GHS has further refined the approach to include addressing the degree of severity of the hazardous effects by assigning categories of hazard within hazard classes; providing detailed scientific approaches to evaluating the available data to help ensure that multiple evaluators produce similar results when classifying hazards; and allowing a broader use of available data by establishing principles where data can be extrapolated in situations regarding mixtures. OSHA believes that these additional provisions in the GHS enhance employee protection in addition to the benefits of having an internationally harmonized approach when preparing labels and SDSs.

To accommodate these refinements, and improve protection for employees exposed to chemicals in the U.S., OSHA is proposing to modify the HCS as follows. First, paragraph (d) would be re-named “hazard classification” rather than the current “hazard determination.” This is to be consistent with the approach and terminology used in the GHS. Similarly, paragraph (d)(1) would be modified to indicate that chemical manufacturers and importers would be required to:

* * * [c]lassify their health and physical hazards in accordance with this section. For each chemical, the chemical manufacturer or importer shall determine which hazard classes, and the category of each class, that apply to the chemical being classified.

Paragraph (d)(1) would continue to allow employers to rely on information received from suppliers.

Paragraph (d)(2) would be similarly modified to use terminology regarding classification. However, the paragraph also includes modifications to address the evaluation process, and the role of testing. The paragraph specifically states that evaluation of the hazards of chemicals requires the evaluator to “identify and consider the full range of available scientific literature and other evidence concerning the potential hazards.” This is consistent with the current HCS, but re-emphasizes the responsibility to fully characterize the hazard of the chemicals. To clarify that available evidence is to be used, new paragraph (d)(2) specifically states that there is no requirement to test a chemical to classify its hazards under the modified provisions—just as there is no such requirement under the current HCS.

Proposed paragraph (d)(2) also refers to Appendixes A and B for further information on classification as in the current standard. However, the proposed Appendixes have been completely changed from the current text. New Appendix A would include the criteria for classification of health hazards, and new Appendix B would include the criteria for classification of physical hazards. These mandatory appendixes would have to be used for the hazard classification process under the proposed revised standard.

Reference to these appendixes is also included in new paragraph (d)(3), which addresses mixtures. This proposed paragraph re-emphasizes that chemical manufacturers and importers must follow the procedures in Appendixes A and B to classify hazards for mixtures as well as for individual chemicals. In addition, this proposed paragraph indicates that chemical manufacturers or importers would maintain the overall responsibility for the accuracy of their hazard classifications for mixtures even if they rely on ingredient information received from a supplier.

During implementation of the current HCS, OSHA allowed formulators of chemicals to develop an SDS by simply providing the SDSs for all the ingredients rather than compiling a specific SDS for the product. OSHA does not believe that this practice is widely pursued, but it would not be permitted under the proposal. The revisions to the approach to classifying mixtures would not lend itself to such a practice. Hazard classification requires consideration and application of bridging principles based on the constituents, as well as the application of a formula when there are multiple ingredients with acute toxicity. These approaches require the evaluator to determine a classification for the mixture as a whole. In addition, this practice places more of a burden on the user of the product to sort out the relevant information for protection of their employees. The formulator is in a better position to assess the information and provide what is needed to their customers.

Under the current HCS, paragraph (d)(6) requires chemical manufacturers, importers, or employers performing hazard determinations to keep a copy of the procedures they follow in the hazard determination process. This provision has been deleted in the proposed revisions because the hazard classification procedures have been specified, and thus all evaluators are following the same process.

Proposed paragraph (d) is thus much shorter and less detailed than paragraph (d) in the existing standard. This is largely due to the approach in the GHS to include the details regarding classification in hazard-specific discussions that address both the individual chemical and that chemical in mixtures. Given the volume of these criteria, it appeared to OSHA that presenting the relevant information in mandatory appendixes was a more efficient way to describe the criteria than including it all in the primary text of the standard. This is particularly true for those many employers reading the standard who do not have to perform hazard classification—the proposed revisions only apply to chemical manufacturers and importers, unless an employer chooses not to rely on information received from them.

Appendix A, Health Hazards. Proposed Appendix A begins with an introduction that includes material related to principles of classification taken from Chapter 1 of the GHS. These address both weight of the evidence, and the approach to mixtures. The remainder of Appendix A is taken from Chapter 3 of the GHS on Health Hazards. OSHA has included the specific discussions of all of the health hazards covered by the HCS in proposed Appendix A, extracted from Chapter 3 of the GHS. Generally speaking, OSHA has proposed the language from Chapter 3 regarding the criteria for classification to minimize deviations from the GHS approach. However, each of the hazard discussions has been reviewed carefully within the context of the HCS, and there has been some editing by OSHA. This has been primarily to shorten the discussions where possible to delete any portions that do not relate specifically to the method of classification for either individual substances or mixtures. Thus OSHA has removed the decision logics that are in the GHS from the proposed criteria, and is considering including them in a guidance document to be made available at the time a final rule is published. The hazard communication portions of the criteria chapters have also been removed since all of this information is already available in proposed Appendix C and is thus duplicative. In addition, as discussed further below, edits have been made where OSHA has not proposed to adopt all of the categories of a particular hazard class.

The chapters on Skin Corrosion/Irritation and Serious Eye Damage/Irritation have been modified more extensively than the other chapters on health hazards in the GHS. In these chapters, the GHS leads the evaluator to conduct additional testing on the chemical when information is not available. While the GHS does not require such testing, the criteria for these effects imply that it should be conducted to complete an evaluation. The HCS is based solely on available information, and no testing is ever required. Therefore, OSHA has modified these chapters to eliminate any references to additional testing, and limit the evaluation to what is known based on available information. It should be noted that the UNSCEGHS has initiated work to review these chapters to edit them and make them easier to follow. OSHA will be participating in this activity.

Each proposed hazard class discussion includes the criteria for classifying a substance or a mixture. Unlike the HCS, which defines across-the-board percentage cut-offs for all hazard classes, the GHS employs a tiered approach to classification. Like the HCS, classification would be based on test data for a mixture as a whole for most hazard classes where it is available. However, where it is not available, but there are data on ingredients and similar mixtures, the GHS allows extrapolation or bridging of data to classify a mixture. This allows greater use of available data before resorting to a percentage cut-off or similar approach. Where such data are not available, the criteria address how to classify mixtures based on cut-offs specific to that hazard. In the case of acute toxicity, this includes calculations based on the acute toxicity of each ingredient in the mixture.

The tiered scheme is somewhat different for certain hazard classes. As described, usually the evaluation is based first on test data available on the complete mixture, followed by the applicable bridging principles, and lastly, cut-off values/concentration or additivity. The criteria for Germ Cell Mutagenicity, Carcinogenicity, and Reproductive Toxicity take a different approach by considering the cut-off levels as the primary tier and allowing the classification to be modified on a case-by-case basis based on available test data for the mixture as a whole. This is related to the sensitivity of available test methods to detect these types of effects at small concentrations in the mixture as a whole.

This may result in some mixtures that are currently considered to pose a particular hazard not being so classified under the GHS. OSHA believes that the protections of the GHS approach are appropriate, and that these changes will not result in an inappropriate reduction in protection. For example, if there is a mixture that is 1% of an acutely toxic material, regardless of the severity of that effect, and it is diluted with 99% water, the current HCS would require that mixture to be considered acutely toxic. Under the GHS, it is unlikely to be considered as such—based on the dilution effect of the water, the acute toxicity is no longer a concern. Thus the bridging principles under the GHS allow for a more accurate assessment of the potential harm of the mixture, whereas the strict cut-off approach under the current HCS may provide hazard information in cases where the exposure is minimal and the occurrence of an adverse effect is unlikely. In the example described, the presence of the water in the mixture as used by the workers reduces the potential for exposure to the hazardous ingredient to such a small amount that no effect is expected to result. The GHS approach is not as simple to apply as the current HCS, but the resulting approximation of the hazards of the mixture will be more accurate.

There are several hazard classes in the GHS that give competent authorities such as OSHA a choice of concentration limits to apply when classifying a mixture containing ingredients that pose these effects (e.g., reproductive toxicity, sensitization, target organ effects). OSHA is proposing to use the most protective of the available concentration limits for these hazard classes, and require information to be provided on labels and safety data sheets at concentrations above 0.1%. Other countries may choose to only provide the information on SDSs when the concentration is higher. These particular health effects are among the most significant to employees, and OSHA believes the provision of information on labels will help both employers and employees ensure that appropriate protective measures are followed.

In determining which categories to propose to adopt, OSHA employed two primary principles in reviewing them. First, the Agency tried to maintain a scope as consistent as possible with the current scope of the HCS, in particular to maintain the level of protection in keeping with that principle established to guide the harmonization process (see Section III)(an approach specifically supported by Document ID #s 0021, 0163, and 0170). Second, consistent with comments received and discussed previously in this preamble (e.g., Document ID #s 0104, 0128, 0155, and 0171), OSHA reviewed what major trading partners of the U.S. have indicated they are proposing to adopt—in particular, the EU since they have already adopted an approach. Where possible, and appropriate in terms of maintaining protections and an appropriate scope for the workplace, OSHA has sought to be consistent with these other proposed approaches for the workplace.

All of the health hazard classes in the GHS have been proposed to be adopted in the HCS. However, for acute toxicity, OSHA is proposing to adopt Categories 1 through 4, but not 5. (See Appendix A.1 for a detailed explanation of acute toxicity categories and their corresponding cut-offs.) The current coverage of the HCS is greater than Category 3 of the GHS, but does not include all of Category 4. If OSHA were to adopt only 3 categories, it would reduce protections with regard to acute toxicity. Adopting Category 4 expands coverage somewhat. However, chemicals meeting the definition of Category 4 are already covered under the national consensus standard on labeling that many chemical manufacturers already follow (ANSI Z129). In addition, those chemicals are already covered by the EU under their existing classification, packaging, and labeling of dangerous substances (Directive 67/548/EEC) and preparations (Directive 1999/45/EC) directives, and their adopted GHS provisions. These countries comprise the largest trading partner in chemicals for the U.S. Thus, many manufacturers are already classifying their chemicals as acutely toxic to comply with European requirements.

Coverage of Category 5 would not only expand coverage significantly, it would lead to inconsistency with Europe and with the current national consensus standard. OSHA also believes that exposures of this magnitude are not likely to be encountered in the occupational setting, and that such coverage would be excessive.

Since OSHA raised this issue for comment, a number of respondents specifically addressed acute toxicity. The responses varied, although a number supported the approach proposed to cover through Category 4 (Document ID #s 0046, 0047, 0077, 0104, 0021, 0123, 0135, 0145, 0155, 0163, and 0171). For example, Dow (Document ID # 0047) stated:

Dow believes that OSHA should adopt all health hazard criteria and categories, except Acute Toxicity Category 5. While this category may be useful for characterizing consumer products, its use with the substances characterized under the HCS would be confusing and unnecessary. Dow understands that the EU and Australia have both chosen not to include Acute Toxicity Category 5 in their implementation of the GHS and that Canada is currently considering doing the same. Dow believes that the U.S. should be consistent with these other major trading partners by not including this category when it adopts the GHS.

Others suggested that OSHA propose to adopt Categories 1 through 3 (Document ID #s 0054, 0034, 0128, and 0141). Some argued that all categories should be adopted to ensure harmonization (see, e.g., Document ID #s 0050, 0078, 0106, 0018, 0036, and 0116).

As indicated, OSHA believes that coverage of Categories 1 through 4 is appropriately protective for the workplace, and leads to the greatest harmonization with workplace authorities in other countries. With regard to coverage of Category 5, OSHA would not preclude inclusion of information on Category 5 on the label or the SDS when implementing the proposed revisions. Thus chemical manufacturers or importers who wish to have one label that suffices for the workplace and the consumer sector, for example, could do that and still be in compliance with the HCS.

While OSHA has chosen not to adopt Category 5 for the reasons described, and it does not appear in the Table A.1.1, Paragraph A.1.3.6.1(a) requires that the calculation of acute toxicity for mixtures “[i]nclude ingredients with a known acute toxicity, which fall into any of the GHS acute toxicity categories.” The intent of this provision in the GHS was to include data on substances classified as Category 5 in the mixture calculation. The exclusion of Category 5 from the text of the acute toxicity table will likely mean that classifiers could overlook substances falling into this category in the mixtures calculation, resulting in a higher (less protective) classification. This could also mean a lack of harmonization within the U.S. if other Federal agencies adopt Category 5, potentially requiring inclusion of these data in the calculation. The European Union GHS system excluded Category 5 for all sectors, and has explicitly excluded Category 5 data from the mixture calculation. OSHA invites comment on whether Category 5 data should be included in the calculation of the acute toxicity of mixtures, and whether exclusion of these data presents a significant difference in hazard classification.

OSHA is also not proposing to adopt Category 3 for skin corrosion/irritation. This particular category appears to cover much more than the current criteria for this hazardous effect under the HCS. In addition, the irritant effects covered by Category 3 are very minor and transient, and of limited applicability in the workplace setting. The Agency received several comments supporting such an approach (Document ID #s 0077, 0034, 0128, 0145, and 0171). This approach is also consistent with the European Union.

OSHA has also not proposed to adopt Category 2 for aspiration hazards covered by the GHS. This category appears to be more appropriate for the consumer sector than the workplace. OSHA does not specifically address aspiration hazards in the current HCS although the Agency believes the more relevant and serious Category 1 aspiration hazards are captured under the broad scope of the rule. Several commenters suggested that Category 2 not be covered when aligning the HCS with the GHS (Document ID #s 0077, 0034, 0128, 0145, and 0171), and the EU does not include it in their requirements. Others suggested that aspiration should not be covered at all since it is not relevant to the occupational setting (Document ID #s 0102, 0104, and 0163). However, OSHA believes that accidental aspiration is possible in the occupational setting, and thus has proposed to adopt the criteria for Category 1.

Appendix B, Physical Hazards. Appendix B includes the criteria for the physical hazards proposed to be covered by the HCS to be consistent with the GHS. The current HCS covers these hazards, but the definitions, while similar, are not the same as those included in the GHS. The GHS based its physical hazard criteria on those incorporated into the United Nations' Recommendations on the Transport of Dangerous Goods. In the U.S., the Department of Transportation (DOT) has already harmonized its definitions with the UN, and thus, with few exceptions, the GHS. While OSHA's initial physical hazard definitions were consistent with the DOT definitions at the time the HCS was promulgated, DOT's harmonization with the international requirements resulted in the two agencies having different definitions. Thus the U.S. has not been domestically harmonized for some years—adopting the same definitions as DOT has in this rulemaking will thus have the additional benefit of accomplishing substantial domestic harmonization.

As with Appendix A and the health hazard criteria, OSHA has edited Chapter 2 of the GHS to shorten the discussions and focus only on the criteria in the proposed revisions. Decision logics and hazard communication information are not included. OSHA is considering a guidance document with the decision logics to be made available when a final rule is completed, and the hazard communication information is already in proposed Appendix C, so to include it in Appendix A would be duplicative.

As with health hazards, OSHA is trying to maintain the current scope of the HCS for physical hazards in the proposal, as well as being as consistent as possible with trading partners, particularly the European Union. One exception may be flammable gases, where it appears that more flammable gases will be covered by OSHA adopting Category 2 than are currently covered by the HCS. OSHA is proposing to adopt all of the physical hazards in the GHS.

The one deviation from the approach adopted by the European Union is in the proposed adoption of Categories 1 through 4 for flammable liquids. The European system only addresses Categories 1 through 3. Given the current coverage of the HCS, not covering Category 4 would be a reduction of protection that OSHA does not believe is appropriate. Thus we are proposing to include coverage of Category 4 in the HCS.

One edit that should be noted occurs in the criteria for explosives. The GHS criteria currently use the term “article” in a manner that is inconsistent with that term as used in the workplace in the U.S. OSHA has changed the term to “item” in these criteria.

While OSHA believes that harmonizing with DOT provides significant benefits, there are some concerns regarding this approach that have arisen in reviewing the physical hazard criteria. These concerns involve the test methods referred to in the GHS criteria, which are based on issues related to the packaging and volume in transportation. Packaging is obviously a major concern in transport, and is used to address or mitigate the risk of conveying certain types of chemicals. These chemicals may or may not be present in the workplace in the same size or type of packaging and the relevance of these factors in the test methods are questionable in terms of workplace exposures. OSHA invites comment on this issue, both in terms of the appropriateness of the criteria as drawn (including the test methods and references to packaging or volume), and any suggestions that interested parties have to address these issues. The criteria of particular interest involve those for self-reactive chemicals, organic peroxides, self-heating chemicals, and explosives.

OSHA raised as an issue for comment in the ANPR the impact of changing some of the physical hazard criteria in other OSHA standards that rely on HCS definitions (for example, process safety management). Many comments were received on this issue (see, e.g., Document ID #s 0042, 0076, 0077, 0015, 0024, 0108, 0128, 0145, and 0163). While opinions varied, generally the consensus was that OSHA needed to make the standards consistent.

OSHA has reviewed all of its other standards, and the possible impact of aligning the HCS with the GHS on those rules. The Agency is proposing changes to some of these other rules, and discusses elsewhere in this preamble the actions it has determined are appropriate to address this issue.

Combustible dust. In the ANPR, OSHA asked for comments on the scope of health and physical hazards covered by the HCS and the GHS. In response, several commenters addressed the issue of combustible dust. There is no specific definition of combustible dust in the HCS, nor is there one in the GHS. A number of explosions have occurred in workplaces due to an accumulation of combustible dust. The U.S. Chemical Safety and Hazard Investigation Board (CSB) has investigated these explosions, and made recommendations to OSHA regarding a number of actions it should undertake (Document ID # 0110). CSB found that hazard communication regarding such dusts was inadequate, and is recommending the following with regard to this rulemaking:

The CSB therefore recommends that OSHA amend the HCS to explicitly address the fire and explosion hazards of combustible dusts, and those materials that could reasonably be expected to produce combustible dusts, among the substances covered by the standard, and also that the Agency require inclusion of dust fires and explosions among the physical hazards that must be addressed in Material Safety Data Sheets. The CSB also requests that OSHA advocate similar changes to the GHS through appropriate international mechanisms.

The Phylmar Group (Document ID # 0080) noted that combustible dust is not specifically covered under the current HCS, but suggested that it should be a future revision to the GHS rather than an addition to the HCS at this point:

Combustible dusts are not addressed in the current HCS or the GHS. Although we believe that combustible dusts should be addressed in future revisions of the GHS, we do not recommend that OSHA include them in this rulemaking, as it would not achieve the desired goal of global harmonization. We encourage OSHA to work with the UN to ensure that the hazards of combustible dusts are addressed in the future.

The American Petroleum Institute also suggested that OSHA discuss with the UN how to handle the classification of explosive organic dusts (Document ID # 0171). Both Dr. Michele Sullivan and Organization Resources Counselors had similar comments which highlighted the hazards of combustible dusts, but suggested that OSHA explore ways this can be addressed on SDSs or in future GHS revisions rather than suggesting modification of the current HCS (Document ID #s 0145 and 0123).

There are a number of activities ongoing in OSHA regarding combustible dust, including consideration of additional standards or regulations addressing this issue. Final decisions have not been made regarding such rulemaking. As noted by commenters, the HCS does not include an explicit definition of such dust. However, manufacturers and importers are required to perform a hazard evaluation and consider all scientific evidence to determine if their products present a hazard. 29 CFR 1910.1200(d)(1) The hazard determination must anticipate the full range of downstream uses of a product including any by-products that may be generated during normal conditions of use. It has been the longstanding position of the Agency that the hazard determination covers dusts known to be subject to deflagration and subsequent explosion, i.e., combustible dusts. This information must be conveyed on the MSDS.

Likewise, the GHS specifically addresses inclusion of information on the hazards associated with explosive (combustible) dusts in the SDS. This information would appear in Hazard Identification (Section 2) on the SDS as a hazard that does not result in classification under the current provisions of the GHS. This provision in the GHS is consistent with OSHA's current coverage of combustible dusts and is included in the proposed modifications. In addition, as discussed above, OSHA has added a definition for unclassified hazards to the proposed rule to address hazards such as combustible dust that do not have specific criteria for classification in the current provisions. Under this definition, combustible dust would be covered as other hazardous chemicals are, including information on labels, SDSs, and in training.

Additionally, the United States has submitted a working paper to propose that the UN Subcommittee add combustible dusts to their program of work, and has volunteered to lead this work. At such time as specific classification criteria for combustible dusts are added to the GHS, OSHA would also add them to the modified HCS. At this point, there are no agreed U.S. criteria to propose to the UN Subcommittee. OSHA invites comments on this issue, and specifically would like to learn what stakeholders believe would be an appropriate definition for combustible dust to add to the GHS as a physical hazard.

Other comments related to hazard determination/classification. A number of commenters responded to OSHA's specific questions related to hazard determination and classification, but few commented generally on the approach in the GHS and the HCS. The Refractory Ceramic Fibers Coalition provided a general discussion on hazard determination, and reached the same conclusion as OSHA regarding the contrast in the approaches (Document ID # 0030):

The GHS and HCS hazard determination/classification are self-classification processes, but the GHS process is more detailed and allows for closer scrutiny of the strengths and weaknesses of the available data. RCFC supports the GHS approach. While the HCS has a one positive study threshold, the GHS provides for the one positive study issue in the context of analysis of the weight of all of the available evidence. In vitro studies are treated specifically, and there is consideration of whether a substance is not bioavailable or is inextricably bound. Professional/expert judgment is included, human experience is taken into account, and negative findings and data which refute findings are considered.

As described above, the existing HCS includes reference to several lists of chemicals in the hazard determination provisions that the Agency considers a “floor” of chemicals that are to be considered hazardous under all circumstances. The lists were also referred to in the mixture provisions—requiring mixtures to be covered when components could exceed established or recommended exposure limits even when present in concentrations below the mixture cut-offs. Inclusion of the floor and the mixture provisions in the revised rule were raised as an issue for comment in the ANPR, and a number of responses were received. Opinions on these issues varied significantly.

A number of commenters thought the revised rule should take the same approach as the existing rule (see, e.g., Document ID #s 0044, 0057, 0078, 0021, 0029, 0116, and 0149). On the other hand, some respondents did not support the inclusion of any additional lists, and several noted that the GHS does not include such an approach, and thus the revised rule should not either since it is being aligned with the GHS (see, e.g., Document ID #s 0046, 0047, 0049, 0058, 0064, 0036, 0107, 0123, and 0171). Others objected to the process by which TLVs are determined and/or suggested that it is not legal for OSHA to refer to TLVs (Document ID #s 0064, 0083, 0100, 0101, 0111, 0132, and 0141).

As OSHA noted in the ANPR, the more detailed hazard classification provisions in the GHS preclude the need for a floor and for the mixture provisions related to exposure limits. The current HCS does not provide a specific and detailed approach to hazard determination or classification of hazards, and thus there was concern during its promulgation about the relative ability of chemical manufacturers and importers to follow a performance-oriented approach and reach the same conclusions. The floor of chemicals, as well as the mixture provisions, reflected this concern by providing additional guidance regarding the types of chemicals that would be considered hazardous were an appropriate hazard determination conducted. The proposed modifications provide a specific and detailed approach, and thus this additional guidance is no longer necessary or appropriate. OSHA believes that the detailed and specific criteria would provide equal or improved protection for exposed employees since they would improve consistency in evaluations, as well as help to ensure a thorough and comprehensive classification. In addition, as noted by some commenters, the GHS itself does not include such lists, so including them in the revised HCS would be a deviation from the harmonized approach. Such a deviation would detract from the benefits of adopting a harmonized approach.

OSHA has thus decided to delete references to any lists in the hazard classification provisions being proposed. The Agency believes that the proposed revised criteria accomplish a similar purpose in ensuring a consistency in approach to classification by various manufacturers of the same product, and does not think these provisions are needed in the proposed standard for this purpose. Furthermore, the GHS does not include a floor list of this type, and maintaining such provisions in the proposed revisions would be a significant deviation from the harmonized approach.

A few commenters argued that the hazard classification approach in the GHS would result in chemical manufacturers testing or re-testing their products (Document ID #s 0061, 0178, 0022, and 0141). If manufacturers choose to test or re-test their products, it will not be a result of either the provisions of the GHS or those proposed for the revised HCS. The GHS does not require testing, and neither does the HCS. Both are based on available data. This has always been the case for the HCS, and is now explicitly addressed in the revised text to ensure it is understood by all stakeholders.

There were some other comments that noted concerns about the effects of the classification criteria on a specific chemical or product, or which noted the potential for a change in classification or the need for additional guidance or interpretation. Since OSHA had not actually proposed language or coverage for the rule in the ANPR, some of these concerns were based on assumptions about what requirements would be included in a revised HCS and thus should be re-considered in the context of this proposal. As noted in the discussion on outreach and compliance assistance, OSHA is open to suggestions regarding areas where help will be needed, and classification has already been highlighted as an area of concern.

One interesting comment that was submitted by a number of respondents involved development of a classification data base (Document ID #s 0047, 0050, 0053, 0054, 0038, 0155, 0160, and 0165). Opinions as to who would develop and maintain such a data base varied (OSHA, U.S. industry, and an international body were all mentioned). During the development of the GHS, chemical industry representatives did not generally support inclusion of such a list or data base of classified chemicals. It appears that the European Union will be making such a data base available for compliance with its requirements, as have Japan, Taiwan, Korea, and New Zealand. Concerns are now being raised by stakeholders that classifications in these data bases are different for the same chemical.

Development and maintenance of such a data base would be a significant undertaking for any entity, although the appeal of such an approach is obvious. The appearance of differing classifications in national data bases is certainly a concern. One development that impacts this issue is that the International Chemical Safety Cards distributed by the International Program on Chemical Safety are being updated to be consistent with the GHS, and will thus have classifications for over one thousand commodity chemicals. Several hundred have already been completed. NIOSH represents the U.S. in this activity (Document ID # 0082), and the cards are available on their Web site (which is linked on OSHA's Web site). These cards are available in multiple languages, and are internationally developed and peer reviewed. Thus they will provide a data base on an international level for a core group of widely available chemicals when the update is completed.

The issue of a data base is one which needs to be explored more fully, and the logistics and implications studied. It has been raised as an issue for consideration by the UN Subcommittee as well. OSHA invites further comment on how such an approach might be further developed.

(e) Written hazard communication program. The GHS does not include provisions for a written hazard communication program. Thus the provisions of this paragraph are not directly affected by implementation of the GHS. The only changes proposed align terminology, i.e., the proposal uses the term “safety data sheet” rather than “material safety data sheet.”

The written hazard communication program requirements are intended to ensure that the approach to hazard communication in a given workplace is coordinated and comprehensive. The program includes a list of the hazardous chemicals known to be present in the workplace. This list is basically an inventory of the chemicals the employer must have safety data sheets for—and is accessible to employees so they, too, can determine what chemicals should be included under the hazard communication programs in their workplace. The list can be maintained by work area or for the workplace as a whole, and can be kept by the “identity” of the chemicals (which would be the product identifier under the proposed rule). In other words, the inventory can be common names or product names, rather than individual chemical ingredients of each product by specific chemical identity or chemical name.

In addition to the list, the HCS requires the employer's program to set forth how hazard communication will be implemented in the workplace. This includes how the standard's requirements for labels, SDSs, and training will be met; how the hazards of non-routine tasks will be addressed; and how hazard communication will be handled in a multi-employer workplace situation. OSHA has provided guidance over the years on completing a written program, and there are many sample programs in circulation. The program need not be lengthy or complicated, but should have enough detail to provide the reader with a blueprint of the workplace-specific program.

Several comments were received from the Small Business Administration (SBA) and others that suggested there would be significant burdens associated with revising the written program as a result of implementing the GHS (see, e.g., Document ID #s 0022, 0027, 0111, and 0164). Revising the chemical inventory was cited by these commenters as one aspect that was likely to be burdensome. Since the chemical inventory is basically a list of the products an employer has in the workplace that are considered hazardous, the only way this list would change as a result of implementing the GHS would be if something that was not hazardous before is now, or vice versa. OSHA believes that this is not a significant concern for three reasons. First, it would be unusual for a chemical to only have one hazardous effect associated with it so that the overall determination of hazard would be affected by a change in classification in one hazard class. Secondly, because HCS currently covers hazardous chemicals, unless the chemical is new, it is highly probable that it is already covered. Third, as discussed above in relation to the scope paragraph, OSHA does not believe that the scope of hazards covered by the GHS, and thus the proposal, is substantially different than the current HCS.

The most likely differences resulting from re-classification under the revised standard is that a chemical would be placed in a category under a hazard class that does not currently include categories. It may also be possible that a chemical may fall into a different category where there are already defined categories (such as flammability). Neither of these differences would necessitate a change in the inventory.

With regard to other changes in the program, it does not appear likely there would be many, if any at all. Written programs usually describe aspects such as who in the organization is responsible for implementing different parts of the program, or the type of in-plant labeling system used. The revised HCS need not affect these aspects at all. Therefore, OSHA does not believe that extensive revisions would have to be made to written programs, including the inventory, under the proposal.

Suggestions have been made by SBA and others for outreach products related to the written program, particularly for an online inventory tool (Document ID #s 0022 and 0027). Given that the inventory is a simple list, it does not appear that anything other than a word processing program would be required to generate this part of the program so OSHA is not certain what is being suggested by these stakeholders. OSHA does not believe that a tool that lists all hazardous chemicals, and allows employers to check off those they have in their workplace, would be feasible given the extensive number of products currently in use in American workplaces. Therefore, if this is what is being suggested, it is not likely to be provided.

OSHA is thus not proposing any substantive modifications to the written hazard communication program, and does not anticipate any significant new burdens associated with revising the program as a result of other modifications being proposed.

(f) Labels and other forms of warning. The HCS is designed to provide information through three different media: labels or other forms of immediate warning; safety data sheets; and training. Labels are attached to the container of chemicals, and thus provide the information that employees have the most ready access to in the workplace. Given that they are attached to containers, they are by necessity somewhat limited in the amount of information they can present. The labels thus provide a snapshot or brief summary of the more detailed information provided to employees in training programs, or available to them on safety data sheets. They are not intended to be a complete or detailed source of information on the chemical.

In the current HCS, the requirements for labels are performance-oriented. At the time the standard was promulgated, there were many different types of labels in use. A common label format used by industry was that provided by the ANSI Z129, Hazardous Industrial Chemicals—Precautionary Labeling standard. Employers following this format at the time provided a number of different types of information on the chemicals involved. However, there were two areas where employers were inconsistent or did not necessarily provide what was needed when following the national consensus standard. The first was provision of an identity on the label that could lead a chemical user to the specific chemical identities for the hazardous ingredients. It was common practice to provide a trade name for a product, but not the names of ingredients, on either the label or the safety data sheet. The second was provision of specific information on the hazards involved, such as the target organ affected.

The current HCS label provisions focus on this typically missing information. On shipped containers, chemical manufacturers or importers are required to include an identity, and appropriate hazard warnings, as well as their name and address or that of a responsible party. The term “identity” is defined in the HCS definitions paragraph (c) as “any chemical or common name which is indicated on the material safety data sheet (MSDS) for the chemical. The identity used shall permit cross-references to be made among the required list of hazardous chemicals, the label and the MSDS.” The hazard warning is to provide specific information about the health or physical hazards posed by the chemical. The term is defined as “any words, pictures, symbols, or combination thereof appearing on a label or other appropriate form of warning which convey the specific physical and health hazard(s), including target organ effects, of the chemical(s) in the container(s). (See the definitions for `physical hazard' and `health hazard' to determine the hazards which must be covered.)”

Similarly, the requirements for in-plant containers specify an identity and appropriate hazard warning. OSHA has taken a flexible approach to in-plant labeling, allowing a wide variety of systems to be used as long as all of the required information is readily available to employees when they are in their work areas. Thus employers were able to continue using existing systems such as the Hazardous Materials Information System (HMIS) and the National Fire Protection Association (NFPA) labeling systems that use numerical rankings of hazard.

The labeling provisions of the current HCS exemplify the overall performance orientation of the rule. They establish the basic information requirements for chemical manufacturers and importers, but do not specify a format, or any particular label elements to be used. As a result, labels are often quite different when the same chemical is addressed by different suppliers, creating the potential for employee confusion. While many manufacturers follow the ANSI national consensus standard, others do not. Large manufacturers have frequently developed their own libraries or repositories of standard phrases, with decision logics for when to apply them to convey a hazard or a precaution. Therefore, not only does this approach lead to labels that are different, it also results in a large duplication of effort by chemical manufacturers developing their own systems.

This performance-oriented approach also did not lend itself to harmonization. Other countries often use more specific approaches, including assignment of standard phrases to certain hazardous effects, symbols, and other label elements. It was clear that the performance orientation of HCS, with its many acceptable varieties of labels, could not be standardized through agreement on content to achieve harmonization.

Given that a more specified approach would also lead to consistency among manufacturers, as well as helping to ensure the same message is received by all exposed employees, OSHA agreed to negotiate a harmonized approach that was more specific than the current standard. This was also agreed to by stakeholder representatives involved in the negotiations. Thus once a chemical is classified as to its hazard classes and corresponding categories, the GHS specifies exactly what information is to appear on a label for that chemical. As described in Part V of this preamble, OSHA believes that these specific labeling requirements will be more protective of employee health and safety than the current performance-oriented standard.

Paragraph (f) thus has more proposed modifications than most of the other paragraphs of the existing standard. The title of paragraph (f)(1) has been changed to indicate it addresses labels on shipped containers. The required information on these labels includes: product identifier, signal word, hazard statement(s), pictogram(s), precautionary statement(s), and the name, address and telephone number of the chemical manufacturer, importer, or other responsible party.

The proposal thus would require that labels on shipped containers contain much more information than under the current standard. However, much of this additional information has already been included by manufacturers, particularly when following the ANSI standard for precautionary labeling. In addition, the OSHA requirements are intended to be the minimum information to be provided by manufacturers and importers. Under the GHS, as well as the current HCS and the proposal, chemical manufacturers and importers are free to provide additional information regarding the hazardous chemical and precautions for safe handling and use. The GHS and the proposal refer to this as supplemental information. Several commenters requested that this be permitted (Document ID #s 0132 and 0145).

Paragraph (f)(2) addresses labeling for unclassified hazards. As noted previously, the proposal ensures that unclassified hazards (such as combustible dusts and simple asphyxiants) will continue to be covered under the HCS. That means that hazard information will have to appear on the SDS, and in certain cases, the label. As there are, however, no harmonized labeling elements available for unclassified hazards, the agency requires the responsible party to determine what information will be included on the label. This evaluation is to be based on the product's hazards and exposures under normal conditions of use and foreseeable emergencies. Hazard information will be included on the label, as appropriate, under supplemental information, as well as appropriate precautionary measures for the safe handling and use of the chemical.

Paragraph (f)(3) elaborates the label requirements by stating that the required information will be taken from new Appendix C of the standard on Allocation of Label Elements, which incorporates the GHS labeling requirements. This Appendix specifies the signal word, hazard statement, pictogram, and precautionary statements for each hazard class and category. It also includes a few basic rules about preparing labels that address precedence of hazards and other topics. Thus once a hazard classification is completed, the chemical manufacturer or importer can refer to Appendix C to determine what information must be included on the label.

In addition to requiring that the information be taken from Appendix C, new paragraph (f)(4) also notes that the harmonized information must be located together on the label, tag, or mark, prominently displayed, and in English, although other languages may also be included if appropriate.

The rest of paragraph (f) in the current standard remains largely the same in the proposed modified text, although conforming changes to terminology are made throughout the paragraph. The current standard's accommodation for labels associated with solid metal is maintained in the revised text, as is the provision regarding conflicts with requirements of the U.S. Department of Transportation. In fact, since transport rules have been harmonized with the other sectors under the GHS, the possibility of a conflict in information is less likely when the HCS is consistent with the international approach. Two commenters specifically noted that OSHA should avoid conflict with DOT (Document ID #s 0064 and 0066). This is already addressed in the standard (currently paragraph (f)(3) and contained in proposed paragraph (f)(6)). They further noted that the exterior package should be for displaying DOT labels, rather than for OSHA labels. In general, this would be true, although there are some cases where the only container serves as both the shipping container and the workplace container, such as drums. In these situations, there are rules in the GHS regarding which pictograms take precedence and the ways in which to display the information. These rules are in Appendix C of this proposed rule.

Under new paragraph (f)(7), OSHA addresses workplace labeling in the proposed text. As noted previously, the current standard provides employers with flexibility regarding the type of system to be used in their workplaces. Some comments suggested that OSHA maintain this flexibility in the revised standard (see, e.g., Document ID #s 0047, 0145, and 0157). OSHA agrees, and the revised text maintains this flexibility by indicating that the employer can choose to label workplace containers either with the same label that would be on shipped containers for the chemical under the revised rule, or with label alternatives that meet the requirements for the standard. It should be noted that while alternatives are permitted, the information must be consistent with the revised HCS. Hazard classifications must be revised as necessary to conform, and the other information provided must be revised to ensure the appropriate message is conveyed.

OSHA is not proposing to modify the remaining paragraphs on labels in the current HCS, including those that deal with alternatives to affixing labels to stationary containers; labeling of portable containers where the materials are transferred from a labeled container, used within a workshift, and under the control of the employee who performs the transfer; ensuring that all containers in the workplace have a label; a requirement for workplace labels to be in English and prominently displayed, while allowing the information to be in other languages as well; and the requirement for updating label information when there is new and significant information regarding the hazards of a chemical.

Several comments raised an issue regarding potential confusion resulting from the numbering of hazard categories in the GHS (see, e.g., Document ID #s 0046, 0054, 0064, 0035, 0123, and 0146). As described in the GHS text, some of the hazard classes that are divided into categories use numbers to designate those categories. Chemicals posing the most serious hazards are assigned to Category 1, and higher category numbers denote less serious hazards. Labels prepared under the Hazardous Materials Information System (HMIS) and National Fire Protection Association (NFPA) systems, on the other hand, use higher numbers to indicate more severe hazards. It was argued that the different approaches would result in confusion and lead to hazardous conditions in the workplace.

OSHA recognizes that the approach to numbering hazard categories in the GHS differs from that used in the HMIS and NFPA systems. However, the Agency does not believe that this will result in confusion. GHS category numbers determine the label elements that would be required for a chemical, but the category numbers themselves would not appear on labels. Where GHS category numbers would appear on the SDS (Section 2—Hazards identification), they would be accompanied by the label elements for the chemical, which would clearly indicate the degree of hazard. OSHA, therefore, does not anticipate that this information will cause employees to become confused. Moreover, the approach taken in the GHS (i.e., assigning higher category numbers to denote less serious hazards) is consistent with the approach used in the DOT transport regulations for many years.

A few commenters also argued that a small package exemption, or some type of prioritization of information on small packages, should be permitted (Document ID #s 0043, 0046, and 0080). The current HCS does not have such an exemption or limitation, but the Agency has allowed practical accommodations in those situations where an issue has occurred. In Revision 3 of the GHS, some provisions regarding small package labels have been included (1.4.10.5.4.4, Labelling of small packagings). The competent authority is given the discretion to implement changes that allow label preparers to reduce the required information to accommodate a small package size. OSHA is not proposing to adopt such a provision, and intends to continue its current approach regarding small packages. Very small packagings are less frequent in the workplace than in consumer settings, and it is difficult to argue that employees should get less information just because of the size of the package. The practical accommodation approach OSHA has been utilizing addresses those situations where there is a valid issue, and ensures that workers receive all of the required information.

Some comments addressed objections to the specific labeling requirements for certain chemicals. For example, the National Propane Gas Association (Document ID # 0068) objected to labeling propane as being “extremely” flammable, stating that it is usually simply addressed as “flammable” in the U.S. In addition, The Fertilizer Institute (Document ID # 0045) objected to having the skull and crossbones on labels for anhydrous ammonia, stating that use of it in fertilizers is necessary for the food supply. Similarly, an argument is made by the Styrene Information and Research Center (Document ID # 0164) that no GHS Category 2 carcinogens should be labeled because it would result in more chemicals being classified as carcinogens than would be under the International Agency for Research on Cancer (IARC) criteria.

Adoption of the GHS is likely to result in a number of situations where current labeling practices are somewhat changed by the introduction of the concept of severity of hazard, and the use of different label elements to convey information. OSHA does not believe that it would be appropriate to designate substance-specific exemptions from classification for reasons unrelated to communication of hazards. In the case of propane, designating it as “extremely flammable” is actually already done by a number of manufacturers or distributors in the U.S., so it is not necessarily a departure from current practice. In addition, NPGA's argument that many propane distributors are small businesses who don't participate in international trade (Document ID # 0068), is not related to improving and enhancing the communication of hazards to employees in the U.S. Provision of an exemption for those engaged solely in domestic commerce would only increase employee confusion about hazardous chemicals in the workplace. Providing information about the degree of hazard will help to ensure that the material is handled with the proper care needed to prevent hazardous effects from occurring. Similarly, the fact that anhydrous ammonia is used for the food supply ignores the significant hazards this chemical poses to workers who handle it. The skull and crossbones will emphasize the degree of severity of the hazard, as well as communicate the hazard to individuals who do not read or speak English—many of whom work in the agriculture industry.

In addition, the mere fact that incorporation of the GHS criteria might change the number of chemicals classified is not a reason to disregard the carcinogens in Category 2. The IARC criteria were one of the primary sources used for development of the GHS criteria, so it does not appear that there is a significant difference in approach. OSHA has had an enforcement interpretation that would allow manufacturers of certain carcinogens, those in IARC Category IIB, to include information about their carcinogenicity on the safety data sheet but not the label. Such an interpretation would not be consistent with GHS, and is not included in the proposed provisions. Therefore, there may be some chemicals that will now have carcinogen labels in addition to SDS information as a result of implementation of the GHS. This will ensure that employees get consistent information about these chemicals from all suppliers. Furthermore, because the current HCS uses the one study criterion, it appears that more chemicals are currently covered under the HCS than under any other criteria applied.

A few comments were received regarding EPA labels for pesticides, noting that signal words in these labels would change if GHS is adopted (Document ID # 0178), and noting that the requirements for these labels are dictated by the Federal Insecticide, Fungicide, and Rodenticide Act (FIFRA), and also control the SDS content (Document ID # 0108). A commenter also argued that pesticide labels are more useful because they are risk-based rather than hazard-based (Document ID # 0108). OSHA believes these concerns are not related to the proposal. The revised HCS would maintain the exemption for additional labels on containers that are labeled in accordance with EPA requirements. If EPA decides to adopt the GHS, then labels for pesticides would be consistent with OSHA labels on other types of products. With regard to SDSs, these are required by the HCS, not FIFRA, and therefore such SDSs must be consistent with GHS provisions under these proposed changes.

While the GHS specifies the information to be placed on a label, it does not provide a specific format for placement, which is similar to current HCS requirements. It was noted that GHS does not specify a location or size of core information on a shipment (Document ID # 0066). OSHA believes that this is best left in a performance-oriented provision, allowing accommodations to be made as long as the information is located together, and is prominently displayed as required.

Other commenters noted that changing labels will create confusion and additional burden (Document ID #s 0065 and 0146); that there may be two labels and SDSs during the transition period, and that would be confusing (Document ID # 0035); and that the diamond shape of the pictogram was similar to NFPA's diamond, and therefore confusing (Document ID # 0035). It is clear that a change in labels will require a period of transition where there may be some confusion, and there will be two types of labels in the workplace. However, when the GHS is completely implemented, the current widespread confusion resulting from allowing multiple labeling approaches will be eliminated. Comprehensibility and effectiveness of hazard communication is expected to increase as a result. OSHA believes these long-term benefits outweigh the short-term transitional issues. As discussed above, commenters in general recognized the benefits of adoption of the GHS, including enhancement of current protections, and thus supported pursuing this rulemaking. (See, e.g., Document ID#s 0046, 0047, 0054, 0059, 0064, 0081, 0034, 0038, 0158, and 0165).

There were a few commenters who wanted additional elements in the labeling system, such as the water-reactive pictogram so it could be posted on buildings for fire authorities (Document ID # 0029), and a numerical ranking system similar to those currently in use under voluntary systems (Document ID # 0013). In the case of the water-reactive pictogram, there is certainly nothing in the current HCS or in the GHS that precludes its use to mark buildings, but that is a purpose that is outside the scope of the system at this point. In terms of the numerical ranking system, the GHS was developed based on consideration of existing national and regional hazard communication systems, and none of those currently employ a numerical ranking system. Thus, such an approach was not considered in the process.

(g) Safety data sheets. The proposed revisions to this paragraph are confined primarily to paragraph (g)(2), other than conforming terminology regarding classification and SDSs. Paragraph (g)(2) of the current HCS indicates what information must be included on an SDS. It does not specify a format for presentation, or an order of information. Chemical manufacturers and importers have been free to use whatever format they choose, as long as the information is provided.

While this performance orientation was supported by chemical manufacturers when the standard was originally promulgated, this was largely based on those who were already providing SDSs and did not want to change their format. As the scope of the standard was expanded to cover other industries, it became clear that SDS users preferred an order of information or a format. In particular, stakeholders such as emergency responders were concerned that not being able to find information in the same place on every SDS could create an increased risk in situations where the information was needed quickly.

Several years after the HCS was adopted, the chemical manufacturers themselves responded to these concerns by developing a national consensus standard that included a 16-section SDS (ANSI Z400). The titles of each section were established, as was the order of presentation. The standard sought to address concerns raised by also putting information of most use to those exposed in the beginning of the SDS, with the more technical data required by health and safety professionals in later sections. They also responded to comments that indicated the SDS should be essentially “one stop shopping” in terms of information on a chemical, and should include other information such as how it is regulated by other Federal agencies, including transport requirements and environmental information.

In 1990, OSHA published a Request for Information (RFI) that addressed the issues of comprehensibility of labels and SDSs (55 FR 20580). There were nearly 600 comments received, and the majority of respondents sought an order of information or format for SDSs. Since the international harmonization process had begun at that point, OSHA thought it would be useful to wait until a globally harmonized SDS was available before changing the requirements. However, through interpretation, the ANSI format has been acceptable for many years, as long as the SDS includes the required information (see CPL 2-2.38D, the compliance directive for the HCS). As explained in Section V of this preamble, OSHA believes that the implementation of a standardized SDS format will enhance hazard communication and be more protective of employee health than the current performance-oriented standard.

The 16-section format continued to be recognized in different countries and organizations over the years, including an International Labor Organization (ILO) recommendation on chemical safety, the European SDS requirements, and an International Standards Organization standard on SDSs. When the GHS was developed, it was decided that this 16-section format was already a de facto international approach, so it was adapted to be part of the GHS. One small change was made to reverse sections 2 and 3 to put hazard information before the chemical names of ingredients. This change has subsequently been adopted by ANSI and other groups to be consistent.

Since the 16-section SDS was initiated in the U.S. by industry, many companies have been using it. This will reduce the impact of adopting the GHS requirements since the major changeover to that approach has already been made by those companies. Others who continued to use different formats will need to change their SDSs to conform. There is already software available in the 16-section format, and it is expected that more tools will be available as the effective dates for compliance approach.

OSHA is proposing to modify paragraph (g)(2) to establish the section numbers and title headings of the sections of the SDS to be consistent with the GHS. Furthermore, a new Appendix D is being added to the standard to address safety data sheets, and it indicates what information must be included in each section.

As OSHA indicated in the ANPR, there are several sections of the SDS that address information that is outside the Agency's jurisdiction (see the list of sections below). OSHA will not be making these sections mandatory for inclusion, nor will any enforcement activity be directed to these sections. However, inclusion of the sections in an SDS is not precluded, and they have been included in the text of the revised standard so people will be aware that a fully GHS-compliant SDS will have to address those areas in addition to the ones mandated by OSHA.

The revised SDS would require the following sections:

Section 1. Identification

Section 2. Hazard(s) identification.

Section 3. Composition/Information on ingredients.

Section 4. First-aid measures.

Section 5. Fire-fighting measures.

Section 6. Accidental release measures.

Section 7. Handling and storage.

Section 8. Exposure controls/personal protection.

Section 9. Physical and chemical properties.

Section 10. Stability and reactivity.

Section 11. Toxicological information.

Section 16. Other information, including date of preparation of the last revision.

A note in the revised text addresses the other sections that are not mandatory for OSHA:

Section 12. Ecological information.

Section 13. Disposal considerations.

Section 14. Transport information.

Section 15. Regulatory information.

The remainder of the paragraph on SDSs remains the same as the current HCS. The proposal retains the current HCS design, ensuring the downstream flow of information from the chemical manufacturer or importer to the distributor and ultimately the employer. Other provisions regarding completion of all sections of the SDS; provisions for complex mixtures; the requirement for information to be accurate and reflect the scientific evidence; the need to update the SDS when new and significant information is available; maintenance of SDSs so they are accessible to employees; accommodations for situations where employees travel between workplaces during a workshift; and access for OSHA and NIOSH, remain as they are in the current standard.

As was the case with labels, relatively few comments were submitted in response to the ANPR on the specific provisions for SDSs in the GHS. Those provisions are generally consistent with the current HCS, with the exception of the standardized approach described above that OSHA is proposing to include in the revised text.

Comments were received on inclusion of exposure limits on SDSs, and a number of different opinions were expressed, particularly regarding TLVs being required. Many commenters argued that TLVs should be included on the SDSs as currently required under the HCS (see, e.g., Document ID #s 0042, 0179, 0021, 0038, 0124, and 0149). Others suggested they should not be required (see, e.g., Document ID #s 0058, 0064, 0036, 0129, 0151, and 0163). There were also a number of commenters that suggested other types of occupational exposure limits that should be included on SDSs, such as levels from other countries, those recommended by NIOSH, and those recommended by the American Industrial Hygiene Association (see, e.g., 0044, 0077, 0018, 0024, 0109, 0147, and 0171). OSHA has decided to maintain the requirement to include its mandatory permissible exposure limits (PELs) on the SDSs, and to specify, as in the existing HCS, that manufacturers should include “any other exposure limit used or recommended by the chemical manufacturer, importer, or employer preparing the safety data sheet.” This will allow inclusion of any of the different types of occupational exposure limits commenters recommended for inclusion where the SDS preparer deems it appropriate. It also helps to minimize differences between the U.S. and other countries by not providing (except for PELs) a list of U.S.-specific occupational exposure limits that must be included, yet provides protection for employees by allowing inclusion of various recommendations that will help employers design appropriate protective measures.

Several commenters appear to believe that the GHS requires disclosure of all ingredients in a mixture, unlike the current rule that has percentage cut-offs (Document ID #s 0048, 0056, and 0064), and argue that the current rule's approach should be maintained. In fact, the GHS approaches ingredient disclosure in a manner consistent with the current HCS, although the cut-offs may be different for the various health hazards covered. Similarly, it was suggested that there be a de minimis level below which SDSs would not be required (Document ID # 0178). This is already addressed by the cut-offs in the mixture classification provisions for each health hazard class. It was suggested that the GHS approach to ingredient disclosure would lead to more testing of chemicals (Document ID #s 0048 and 0056). This is not true as neither the current HCS nor the GHS require testing of any kind to be performed.

A number of comments suggested specific information to be included on the SDS, such as the Chemical Abstracts Service Registry Number (Document ID # 0044); whether a chemical is an EPA hazardous waste (Document ID # 0059 and 0108); control banding recommendations (Document ID # 0081); lethal dose data (Document ID # 0015); a miscellaneous section (Document ID # 0019); NFPA and HMIS ratings (Document ID # 0019); storage requirements (Document ID # 0019); reference to the DOT Emergency Response Guide (Document ID # 0019); and more spill cleanup and disposal information (Document ID # 0028). Much of this information is already included in the proposed SDS (such as the CAS Registry Number and lethal dose data). The other information noted could certainly be included in the SDS as additional information to that which is required by OSHA. The information referenced by these comments that falls under sections of the SDS that are not workplace-related (e.g., environmental and transport information) cannot be required by OSHA. The Agency would certainly not preclude inclusion of such information by SDS preparers voluntarily, or as a result of requirements at some time in the future by the other Agencies that do have responsibility for those subject areas.

Several commenters noted that SDSs need to be written in plain language (Document ID #s 0044, 0010, and 0035). In general, the Agency agrees that SDSs should be written as plainly as possible while still conveying the required information to the intended audiences. As originally designed by ANSI, the sections in the beginning of the SDS are intended to be written in plain language, with fewer technical terms where possible. This information should be of immediate use in emergency situations for example. But many of the remaining sections of the SDS require technical information, and they are intended to be of use primarily to professionals designing protective measures or providing services such as medical surveillance to exposed employees. These sections need to retain their technical terminology in order to be useful to the professionals for these purposes.

A number of the comments received dealt with the management of SDSs, rather than the specific requirements for preparing them. For example, one commenter said that there would be a large burden associated with sending letters to obtain new SDSs, tracking their receipt, and updating workplace data bases (Document ID # 0178). The proposal would employ the same approach as the current HCS for distribution of SDSs. During the phase-in period for the standard, chemical manufacturers, importers, and distributors will be required to send a new SDS with their next shipment of a chemical to their customers. In other words, employers should automatically receive new SDSs, just as they do now when an SDS is updated. There will still be a burden associated with updating workplace records, but since users are not required to solicit new SDSs, there will not be a burden of sending letters to suppliers and tracking receipt of the responses. Furthermore, the phase-in period should be long enough that there will be turnover of chemical supplies that necessitate a new shipment in most cases.

Several commenters suggested that an online library of SDSs be created by OSHA (Document ID #s 0019, 0028, and 0146). This is an approach that was investigated by OSHA in the past, and at that time, it was determined that it would not be feasible for the Agency to maintain a complete and up-to-date data base of all the SDSs in use in American workplaces. The number of SDSs involved is very large, and there is no way for the Agency to know about each SDS or when each is updated. OSHA believes this approach is still infeasible for the Agency.

There appeared to be some concern about having two SDSs for the same product during the phase-in period, and how an employer would decide which takes precedence (Document ID # 0146). OSHA believes that the most recent version would be the one that takes precedence, and should be maintained in the workplace. It would not be necessary to maintain two versions for purposes of the proposed standard.

There was also a comment regarding SDS management for construction sites, and the use of a FAXback system (Document ID # 0022). This is an issue that has long been addressed by OSHA in its compliance directive (CPL 2-2.38D), as well as in the standard itself (see paragraph (g)(8) of the existing HCS), with provisions for what would be considered effective electronic access to SDSs. The proposed revisions to the rule do not change these requirements.

(h) Employee information and training. The GHS does not include harmonized training requirements, but does recognize the important role that training plays in hazard communication. For example, 1.1.3.1.3 of the GHS states:

In the workplace, it is expected that all of the GHS elements will be adopted, including labels that have the harmonized core information under the GHS, and safety data sheets. It is also anticipated that this will be supplemented by employee training to help ensure effective communication.

OSHA agrees that training is key to ensuring effective hazard communication. Under the current HCS, training is used to explain the label and SDS systems used in a workplace, as well as addressing the hazards of chemicals and protective measures. While the written information provided is clearly important, training is an opportunity to explain the data and helps to ensure that the messages are being received accurately so they can be acted on appropriately. (See Section V of this preamble.)

The training provisions in the HCS do not need to be modified to be consistent with the GHS since it does not include such requirements. However, OSHA is proposing small revisions to track terminology used in other paragraphs, as well as to clarify the requirement to train on the details of the hazard communication program in (h)(3)(iv). While this has always been required in the HCS, OSHA believes that modifying the text slightly will convey the need to address both the labels that will arrive on shipped containers, as well as any workplace-specific system that the employer uses. In addition, the training on SDSs must include the order of information. So the revised text would read:

The details of the hazard communication program developed by the employer, including an explanation of the labels received on shipped containers and the workplace labeling system used by their employer; the safety data sheets, including the order of information and how employees can obtain and use the appropriate hazard information.

In addition, OSHA is proposing that employers train or re-train employees regarding the new labels and safety data sheets within two years after the rule is promulgated. The Agency believes that the training needs to be completed by the time employees begin to see labels and safety data sheets with the new information on them, rather than waiting until after the transition has been completed. Comment is invited on this approach.

Some commenters noted that training would be required to ensure employees understand, in particular, the symbols and pictograms that will be used on labels. Some argued that the burden would be substantial given that all training would have to be revised, and the time and resources required would be significant (see, e.g., Document ID #s 0178 and 0153). However, many agreed that having a standardized approach to labels and SDSs will make training easier in the future than training under the current rule where chemical manufacturers and importers can use whatever formats they choose (see, e.g., Document ID #s 0042, 0072, 0077, and 0030).

Marshfield Clinic (Document ID # 0028) noted that communication of information about chemicals and other hazardous substances:

* * *[I]s one of the more difficult to get across to workers. It is very appreciated that OSHA is revisiting this. Standardization will greatly assist in giving workers a better understanding of the hazards they may encounter when working with chemicals and other hazardous substances.

Similarly, Alcoa (Document ID # 0042) suggested that: “A standardized format will simplify hazard communication training and the use of pictograms will alleviate some of the problems presented by poor language skills.”

There were a few commenters who argued that the standardized approach either would not simplify training, or they did not know if it would (see, e.g., Document ID #s 0065 and 0078). Another noted that the current approach is fine for companies that are domestic only (Document ID # 0026).

There were also many comments related to outreach that suggested compliance assistance in the area of employee training. As OSHA noted in the ANPR, the Agency is considering the development of generic training on symbols to make available to employers (71 FR 53624). OSHA has been working with NIOSH to prepare training on symbols and pictograms in particular (addressed by NIOSH in their comment at Document ID # 0082). However, it is expected that there will be other products related to training as well, both from OSHA and from the private sector.

(i) Trade secrets. The current HCS includes provisions that define what can be considered trade secret information under the rule, as well as delineate the conditions under which this information must be disclosed to ensure the safety and health of exposed employees. These provisions were a significant focus of the original rulemaking on the HCS, and reflect the common law of the United States on this topic. In the years since the rule has been in effect, however, this issue has not been as important. Overall, since these provisions were promulgated, it appears that fewer claims of trade secrecy have been made, and fewer requests for trade secret disclosure have been received, than were anticipated during the rulemaking process.

The negotiations for development of the GHS recognized at the outset that trade secrets—generally referred to internationally as confidential business information—would be an issue of concern. Guiding principles included the following:

In relation to chemical hazard communication, the safety and health of workers, consumers and the public in general, as well as the protection of the environment, should be ensured while protecting confidential business information, as prescribed by the competent authorities.

As the issue was considered further, it was recognized that laws regarding confidential business information were very much country-specific, and had a broader context than rules for classification and labeling. Such laws could not be modified or harmonized through the process of harmonizing classification and labeling. Thus it was determined that the GHS would recognize the importance of the issue, and provide principles for countries to follow when adopting the provisions. These principles are consistent with the approach already incorporated into the HCS.

First, the type of information that can be considered confidential or trade secret is limited to the names of chemicals and their concentrations in mixtures. Under the current HCS, OSHA did not require that concentrations in mixtures be disclosed, and thus limited claims to specific chemical identities. This is the primary difference between the current rule and the proposed revisions to HCS. To be consistent with GHS, OSHA is proposing to add percentage composition information to the SDS. This introduces the possibility that trade secret claims will be made for this type of information, as well as specific chemical identities. Thus the proposal revises the text of the current rule to add consideration of percentage composition everywhere specific chemical identity is addressed in the provisions.

The GHS further suggests that SDSs indicate when information has been withheld as confidential; that the information be disclosed to the competent authority upon request and under condition of confidentiality; that the information must be disclosed in a medical emergency, with mechanisms to protect it while ensuring timely disclosure; that the information be disclosed in non-emergency situations, also under conditions of protecting confidentiality; and that the competent authority have procedures to deal with challenges to this process. All of these principles have already been included in the trade secret provisions of the HCS, and are maintained in the revised rule as previously promulgated. The proposed revisions simply conform terminology, and add text regarding percentage composition being subject to the same provisions as specific chemical identity.

Very few comments on trade secrets or confidential business information were received in response to the ANPR. It was suggested that protection of confidential business information should be an implementation principle for the GHS modifications to HCS (Document ID #s 0072 and 0179), and that the current trade secret position should be retained (Document ID # 0049). There was also a comment that indicated full disclosure of all ingredients should be required on the SDS unless the employer provides a justification to the Agency showing that a particular ingredient is a trade secret, and demonstrating that the economic damage of disclosure exceeds the damage associated with the potential health effects to exposed employees (Document ID # 0044). In addition, the National Paints and Coatings Association (NPCA) argued that the approaches to protection of confidential business information need to be harmonized (Document ID # 0050). As NPCA noted, different approaches may lead to development of different SDSs for various authorities.

As noted above, laws regarding confidential business information are generally not specific to classification and labeling requirements, but rather reflect an overall approach of a country. It was not possible to change such laws through the harmonization of classification and labeling, and thus the limit of the agreement was to establish the principles already described. Those principles are consistent with law in the United States, and do not require any modifications to the current HCS approach to be consistent with the GHS.

As implementation moves forward in different countries and regions, conformance to the GHS principles should lead to increased harmonization of approaches. This is an area that should be monitored to determine if further action can be defined and implemented. OSHA does not believe it would be prudent to implement changes in the approach to trade secret protection and disclosure before that time.

(j) Effective dates. OSHA is proposing to require implementation of the revisions to the HCS in 3 years after the final rule is completed. Training would be required two years after the final rule, and all provisions would be implemented in 3 years. During the transition period, employers would be required to be in compliance with either the existing HCS or the modified GHS, or both. OSHA recognizes that hazard communication programs will go through a period of time where labels and safety data sheets under both standards will be present in the workplace. This will be considered acceptable, and employers are not required to maintain two sets of labels or safety data sheets for compliance purposes. However, given the longstanding requirements for a hazard communication program, there must be no time during the transition period when hazard communication is not in effect in the workplace, and information is not available under either the existing requirements or the new final standard for exposed employees.

Many comments were received on the issue of phasing in the requirements of the GHS, as well as on current practices and time frames required for various activities. There was a wide variety of opinions, as well as a number of factors that commenters suggested should be considered in establishing effective dates.

OSHA specifically requested input on the possibility of phasing in requirements based on the size of the business. While a few commenters supported this approach (see, e.g., Document ID #s 0022, 0144, 0146, and 0151), many more indicated that this would not be appropriate (see, e.g., Document ID #s 0042, 0018, 0033, 0107, 0116, 0123, 0147, 0154, and 0171). One reason given was that the supply chain may involve large businesses purchasing from small businesses, and thus they would need information from them in order to comply themselves (Document ID #s 0080 and 0123).

There were also those who thought the phasing should be coordinated with other trading partners, particularly the European Union (Document ID #s 0072, 0080, 0081, 0179, 0024, 0163, and 0171). The European phasing is taking place over a long period of time because of the REACH requirements for chemicals that are going into effect. The long time periods being considered do not necessarily reflect a determination that the amount of time is needed just for compliance with GHS. Another suggestion that had support was to phase in substances first, and then cover mixtures, or to have a 3-step phase-in that includes intermediates before mixtures (see, e.g., Document ID #s 0104, 0021, 0024, 0034, 0036, 0122, 0141, and 0154).

A number of other phasing approaches were also mentioned, including selecting the 200 most produced chemicals by weight and then sort them by hazard (Document ID # 0139); examining the data available on the chemicals in determining which to do first (Document ID #s 0081 and 0036); basing it on the time to use up stockpiles (Document ID # 0022); and “sufficient” time to work through the supply chain (Document ID #s 0068 and 0122).

There were also suggestions for a specific number of years, or a range of years. Some of these suggested less than 3 years (see, e.g., Document ID #s 0064, 0019, and 0028). A number suggested 3 to 5 years, or in some cases, 6 years (see, e.g., Document ID #s 0042, 0046, 0104, 0015, 0032, 0038, 0111, 0125, and 0163). And there were some commenters who suggested anywhere from 7 to 13 years for full compliance (see, e.g., Document ID #s 0050, 0077, 0078, 0018, 0116, 0129, 0141, and 0164).

OSHA decided on the 3-year proposal based on a consideration of the widely diverse viewpoints expressed, as well as information provided by commenters about stockpiles and other issues. It is clear that activities have already begun by a number of vendors of software programs for hazard classification and labeling to convert to the GHS and make programs available for companies to use to comply with requirements around the world as countries adopt the GHS. This work is already underway, and by the time this rulemaking is finalized, it is expected that much of it will be completed. And there were commenters that indicated that work is already being done in their companies to comply, particularly those that are multinational. (See Section VII for an analysis of activities already underway.)

While the Agency wants to provide sufficient time for compliance, there is also a concern about the effect on employees of dealing with multiple systems during a transition period. While some time period when the currently required labels and the new GHS labels will co-exist is inevitable, the longer this period continues, the less effective the communication to employees will be. It is therefore important to minimize the effects of the transition on the effectiveness of hazard communication by ensuring that is completed in a timely fashion, while allowing adequate time for an orderly changeover.

Requiring the phasing in of substances first, and then mixtures, clearly has some persuasive logic as an approach. However, the supply chain is not always orderly and logical. It cannot be assumed, for example, that no mixtures can be completed until all substances are done. Mixtures that are comprised of substances that are widely available, and their hazards are well known, do not need an extensive time period to complete. Some mixtures are comprised of other mixtures rather than substances, and producers of such mixtures will need information on the component mixtures before they can comply. Waiting till the end of an extensive time period to complete their work may not allow them to meet the compliance dates. These types of issues are generally addressed by the market, and the needs of a manufacturer's customers, and cannot be individually addressed in a phasing-in period. Further comment on this issue would be helpful to determine whether the final rule should include such phasing by type of product.

Other Standards Affected by the GHS Modification to the HCS

OSHA has reviewed all its standards and is proposing to modify standards in General Industry (29 CFR part 1910), Construction (29 CFR part 1926), and Shipyards, Marine Terminals and Longshoring (29 CFR parts 1915, 1917 and 1918) that contain hazard classification and communication provisions in order that they will be internally consistent and aligned with the GHS modifications to the HCS. There is strong support in the record for including these OSHA standards in this rulemaking.

The issue of how to deal with OSHA's existing standards was raised in the ANPR. (71 FR 53617; Sept. 12, 2006). OSHA specifically requested input on how GHS provisions addressing classification of physical hazards such as flammable liquids would impact other OSHA standards. OSHA also asked whether physical hazard definitions in other standards should be changed at the same time as HCS (71 FR at 53623, 53626).

In response to the ANPR, the majority of commenters who addressed the impact of the GHS on other OSHA standards recommended the Agency review all its standards and update them for consistency with GHS (Document ID #s 0046, 0050, 0054, 0072, 0077, 0179, 0031, 0038, 0107, 0116, 0145, 0147, 0154, 0155, 0163, 0165, and 0171). Abbott Laboratories addressed the issue in terms of substance specific standards:

OSHA should conduct a complete review of substance specific standards and determine how they need to be changed in order to be consistent with GHS. These changes should be made concurrent with the implementation of GHS. (Document ID # 0046)

Other commenters agreed, urging OSHA to complete these revisions in one rulemaking. (Document ID #s 0079, 0123, 0137, 0154, and 0157). For example, the National Paint Coatings Association, whose members produce up to 70,000 formulated products, urged OSHA to update the standards impacted by the GHS modification to the HCS to “minimize discrepancies and inconsistency”. (Document ID # 0050). Similar views were expressed by the Marshfield Clinic, the Hazard Communication Group and BASF (Document ID #s 0028, 0154, 0119, 0145, and 0155). NIOSH supported OSHA's plan to “adopt the specific labeling requirement and the safety data sheet (SDS) order of information” in the GHS, which, if substance specific standards were not included, would lead to internal inconsistencies (Document ID # 0081). The American Chemical Society noted that it would be best if OHSA identifies and updates all affected OSHA standards at once, otherwise industry may not realize all potential benefits (Document ID # 0165). The Association of Occupational Health Professionals in Healthcare (AOHP) stated:

The standardization needs to be applied from the beginning until the end of the production, through distribution and use by the end user. We would recommend that any other OSHA standards that would be affected by the adoption of the HCS be changed to coincide with the implementation of the HCS” (Document ID # 0051)

Of the commenters who specifically addressed adopting GHS provisions on physical hazards, many urged the Agency to conform the OSHA standards to the GHS in order to minimize discrepancies and ensure consistency (Document ID #s 0050, 0072, 0104, 0105, 0018, 0012, 0144, 0139 and 0140). One commenter, 3M, noted that adoption of the GHS physical hazard criteria (without changing OSHA standards) would “create unacceptable inconsistencies between OSHA standards” (Document ID # 0128).

However, several of the commenters pointed out some of the difficulties with adoption of the GHS physical hazards criteria (Document ID #s 0077, 0031, 0034, 0038, 0145, and 0166). MRS Associates stated that “flammability is the key physical hazard that needs to have consistent definition and criteria because it affects other standards” (Document ID # 0145). Other commenters agreed with MRS associates (Document ID #s 0072, 0105, 0179, 0145, and 0163). Manufacturer 3M posited that “consistent classification between HCS and storage and handling requirements is the most critical potential problem” (Document ID # 0128). However, some commenters recommended OSHA limit changes in order to facilitate GHS implementation. (Document ID #s 0047, 0064, 0077, 0104, and 0115). Dow Chemical wrote:

Dow believes that OSHA should implement only those changes needed to facilitate GHS implementation. While this may necessitate some duplicative information on SDSs (for example, listing both GHS and NFPA flammability classifications), this would cause less disruption and confusion than trying to make changes i[n] associated standards that might then be in conflict with other current standards outside OSHA's control (for example, State and local building and fire codes) (Document ID # 0047).

OSHA's proposal reflects the advantages of harmonizing, but takes into account the places where harmonization might be too difficult at this time because it would substantially change the scope of coverage of a current standard or make OSHA's standards incompatible with other widely accepted standards.

OSHA reviewed all its standards and has proposed changes to ensure that they are internally harmonized to facilitate safety and health for the employer and employee. To that end, OSHA is proposing to apply the GHS elements it is adopting in the modified HCS to its other standards. Provisions in OSHA standards, such as the substance-specific standards that set forth hazard and precautionary statements will be changed to be consistent with GHS terminology. Also, OSHA is proposing to modify provisions of the standards that reference the HCS definitions to maintain coverage or consistency with the modified HCS, and to change provisions in standards that affect the information requirements of the safety data sheet (SDS). OSHA will also maintain the current HCS definitions in the several standards that reference the HCS for which the adoption of GHS definitions could potentially impact the scope of those standards.

Some standards are not being included in this rulemaking. As explained in more detail below, OSHA is not proposing at this time to change certain standards that reference consensus standards such as National Fire Protection Association (NFPA) standards. In addition, OSHA is not proposing any changes in 29 CFR 1910.109 Explosives and Blasting Agents and 29 CFR 1926.914 definitions for Blasting in Excavation Work Under Compressed Air.

Substance Specific Health Standards

OSHA proposes to update substance-specific health standards in General Industry, Construction, and Maritime, whether they specifically reference HCS or contain their own hazard communication requirements. OSHA is proposing to modify these standards in the following areas:

  • Revise the provisions covering workplace signs to require warning statements that are consistent with the GHS modifications to HCS;
  • Revise all standards to reference the modified HCS for labels, safety data sheets, and training, and identify the hazards that need to be addressed;
  • Maintain the requirement to avoid creating dust currently in some substance-specific health standards, but for which GHS modifications contain no equivalent statements at this time;
  • Maintain or specify language for contaminated clothing and debris;
  • Update most definitions in § 1910.1450, Occupational Exposure to Hazardous Chemicals in Laboratories, to maintain compatibility with the modified HCS; and
  • Change the name Material Safety Data Sheets to Safety Data Sheets and require information on them to be compliant with GHS in content, format and order.

OSHA is proposing to update the language for workplace signs and labels to incorporate the GHS hazard statement and the applicable precautionary statement(s), where required. Most OSHA substance-specific health standards require hazard warning signs, usually for regulated areas, and the language required on the signs varies greatly (e.g., Asbestos, 4-Nitrobiphenyl, 13 Carcinogens, Vinyl Chloride, Inorganic Arsenic, Cadmium, Benzene, Coke Oven Emissions, Cotton Dust, DBCP, Acrylonitrile, Formaldehyde, Methylenedianiline, 1,3-Butadiene, Methylene Chloride, and Lead). With the GHS revision, these standards retain the requirements for specific warning language for specific signs; however, OSHA is proposing to modify the language to be compatible with GHS and consistent throughout the OSHA standards.

OSHA believes that having signs and labels in the same formats and containing identical warnings for the same health effects will make it far easier for employers and employees to quickly recognize the hazard and the degree of danger of a hazard, thus enhancing communication. For example, many of the substance-specific health standards were regulated as carcinogens; however, the hazard statements required on signs and labels range from “Cancer Hazard” in Inorganic Arsenic (29 CFR 1910.1018) to “Cancer—Suspect agent” in Vinyl Chloride (29 CFR 1910.1017) to “May Cause Cancer” in Methylenediamiline (MDA) (29 CFR 1910.1050). The GHS revision to HCS will standardize the warning language to “May Cause Cancer” for each standard regulated as a carcinogen. NAHB addressed this issue, positing that the different signal words (“Danger” versus “Warning”) and different hazard statements (“May cause cancer” versus “Suspected of causing cancer”) may create confusion (Document ID # 0065). OSHA believes that the signal words and hazard statements in its substance-specific standards would be more consistent if they are changed to reflect the GHS modification to HCS.

Currently, OSHA standards appear to suggest gradations of cancer hazards with “cancer hazard” seeming to signal the greatest hazard. However, there is no gradation of hazard. The standards were promulgated at different times and reflect the language used at the time and not relative degrees of hazard. With GHS harmonization, the potential misperception of degree of carcinogenic hazard is alleviated and the process is simplified with one statement warning that the chemical is carcinogenic. “May Cause Cancer” means “carcinogen,” is equivalent to any of the warnings for the current standards, and communicates the serious adverse health effects caused by carcinogens. Nevertheless, NAHB's concerns with potential confusion over hazard statements and signal words are well taken. This highlights the need for training. OSHA believes that after hazard communication training “May Cause Cancer” and other GHS compliant warnings will be quickly recognized and easily understood, leading to more effective avoidance of the various hazards to which workers are exposed. See Table XV-1 for a comparison of the language on current signs to signs modified to be consistent with the modified HCS.

BILLING CODE 4510-26-P

BILLING CODE 4510-26-C

OSHA's proposal would result in all the substance-specific health standards making reference to the HCS and would remove the specific language that must be included on a label for raw materials, mixtures, and products. Currently, OSHA substance-specific standards are inconsistent in that some have their own hazard communication requirements while others reference the HCS and still others are silent, but still are covered by HCS. The new paragraph that will reference the modified HCS in each substance specific standard states:

( ) Hazard communication. The employer shall include (insert name of chemical) in the workplace hazard communication program established to comply with the Hazard Communication Standard (HCS) (29 CFR 1910.1200). The employer shall ensure that each employee has access to labels on containers of (insert name of chemical) and safety data sheets, and is trained in accordance with the provisions of HCS and paragraph () of this section. The employer shall provide information on at least the following hazards: (insert hazards)

Requiring standards to reference HCS will ensure consistency with the GHS revisions and consistency among the standards, and consistency when the specific chemical is part of a mixture. Removal of the current specific warning language is essential for adoption of the GHS language. To leave these provisions in the standards would result in the untenable situation of two potentially conflicting requirements, only one of which (the reference to HCS) would be in accord with the GHS modifications. Moreover, the hazard statements specified for the chemical in the standard may no longer be correct when the chemical is part of the mixture. As for the standards that now simply reference HCS, labeling will no longer be performance-oriented where producers and employers could choose any language and format that conveyed the necessary information. The GHS revision to HCS requires specific GHS elements, including pictograms, hazard and precautionary statements and signal words on labels.

OSHA recognizes that employers have relied upon the warning language for labels in the substance-specific standards and that the absence of language where it had been in the standard could cause some initial confusion as to what, if anything, is required. Therefore, OSHA is proposing to provide guidance on the potential health outcomes that must be reviewed when classifying a substance. The Agency is not attempting to formally classify each substance; rather, OSHA is proposing to provide a list of health effects that will assist the classifier in determining what must be considered for inclusion on the new labels. The GHS classification process for a specific substance as proposed in this revision of the HCS will dictate the hazard warnings and the precautionary statements that will be required on the new GHS-compliant labels. In determining which hazards to include in the substance specific standards, the Agency's primary sources on health effects were its own information gained in rulemaking and subsequent experience, the NIOSH Pocket Guide to Chemical Hazards (2005), and the International Chemical Safety Cards (ICSC), which are an undertaking of the International Programme on Chemical Safety (a joint activity of three cooperating International Organizations: namely the United Nations Environment Programme (UNEP), the International Labor Office (ILO) and the World Health Organization (WHO)), and which are peer reviewed by a group of internationally recognized experts. As a secondary source, OSHA also considered the European Union's (EU) “Proposal for a Regulation of the European Parliament and of the Council on classification, labelling and packaging of substances and mixtures, and amending Directive 67/548/EEC and Regulation (EC) No 1907/2006”. From these sources, OSHA developed hazard endpoints that were to be included in the substance-specific health standards based on two criteria: (1) the health hazard was the basis for the original rulemaking; or (2) the health hazard was asserted by OSHA, NIOSH or ICSC, and confirmed by a second source. For example, acrylonitrile (AN) 1910.1045 was regulated based on its carcinogenicity. Skin sensitization was acknowledged by OSHA, ICSC, and EU; skin irritation by OSHA, NIOSH, and EU; respiratory tract irritation by ICSC and EU; eye irritation by OSHA, NIOSH, and ICSC; liver effects and central nervous system effects by ICSC and NIOSH; acute toxicity by OSHA, ICSC, and EU; and flammability by ICSC, NIOSH and EU. Because all these effects met the criteria for inclusion, skin irritation, respiratory irritation, eye irritation, liver effects, central nervous system effects, acute toxicity, and flammability were added as potential hazards to AN. See Table XV-2 for the proposed list of health effects for each substance-specific health standard.

OSHA is proposing to maintain specific language for labels in its substance-specific health standards for containers of contaminated clothing or waste and debris even though these labels may not be consistent with the GHS. This is to ensure that protection gained from communicating these hazards to the downstream recipients of the materials is not lessened. Substances found on contaminated clothing and waste and debris often occur in unknown and frequently small quantities. In order to ensure and maintain protection for employees in the receiving workplaces, labeling of these hazards is essential.

BILLING CODE 4510-26-P

BILLING CODE 4510-26-C

In addition, OSHA has determined that the hazard and precautionary statements that address creating dust in the substance-specific health standards must be maintained even though there is no GHS equivalent. At this time, a work group formed under the UN Subcommittee of Experts for the GHS is working to finalize issues related to hazard and precautionary statements. As indicated in Section II of this preamble , this work is likely to be accomplished prior to the promulgation of the Hazard Communication final standard (See UN/SCEGHS/15/INF.26). If the UN subcommittee adopts a precautionary statement for creating dust, the paragraphs in the substance-specific standards can be removed and protection will be attained by the GHS modifications to HCS. However, if this does not occur, OSHA intends to continue to require them in the standards.

OSHA's Cadmium Standard provides an example of this issue. In paragraphs 1910.1027(m)(3)(i) and (ii), containers must be labeled in accordance with HCS and the label must include the phrase “Avoid Creating Dust.” In this case, there is no equivalent statement in GHS. Therefore, OSHA would continue to require this statement on labels. That said, OSHA believes inclusion in GHS would be the best way to require this information and if the UN subcommittee has completed its work in time, the statements could be removed from the standards, and the GHS modification to HCS would be relied upon to require the warning.

OSHA is proposing to modify most definitions in § 1910.1450, Occupational Exposure to Hazardous Chemicals in Laboratories (the laboratory standard), in order to maintain compatibility with HCS. This is consistent with the goal of this rulemaking and the original intent of the laboratory standard. OSHA explained in the preamble to the laboratory standard the importance of having the HCS and the laboratory standard both use the same definitions for hazardous chemicals.

The term “hazardous chemical” used in this final rule relies on the definition of “health hazard” found in the OSHA Hazard Communication Standard. As discussed in the scope and application section above, commenters urged OSHA to maintain consistency in terms between the Hazard Communication Standard and this final standard since laboratories are subject to both regulations. (55 FR 3315 Jan. 31, 1990)

There is one exception in the laboratory standard and that is the definition of “select carcinogens.” (§ 1910.1450(b)). In this rulemaking, OSHA is proposing to maintain the current definition of “select carcinogens” in the laboratory standard since the original purpose of the standard was to deviate from the HCS definition and narrow the scope of the standard. As noted in the preamble, the scope was set for “select carcinogens” based on the small, often minute, quantities of substances handled. OSHA stated its reasons for this deviation in the preamble to the final rule and those reasons remain persuasive

This final rule, however, modifies the carcinogen definition and the obligatory action so that special provisions must be explicitly considered by the employer, but need only be implemented when the employer deems them appropriate on the basis of the specific conditions existing in his/her laboratory. Moreover, the term, “carcinogen” has been replaced by “select carcinogen” which covers a narrower range of substances * * * (55 FR 3315 Jan. 31, 1990)

OSHA is also proposing to change the name of the “material safety data sheets” for the substance specific standards to “safety data sheets.” As discussed above, this change is being proposed to reflect the GHS terminology.

Safety Standards

OSHA is proposing to modify safety standards that either directly reference the HCS or provide information pertinent to the Safety Data Sheets (SDSs), in particular regarding the storage and handling of chemicals. As noted above, some commenters supported standardizing physical hazard criteria across all applicable OSHA standards (Document ID #s 0104, 0105, 0034, 0155, 0170, and 0171). However, some other commenters, and even some who supported applying physical hazard criteria across all standards, raised concerns about storage and handling requirements; degree of impact; potential effects on the scope of the Process Safety Management (PSM) Standard; and potential conflicts with widely accepted consensus standards (Document ID #s 0104, 0038, 0077, and 0163). OSHA is addressing all of these concerns in this proposal. OSHA's proposed integration of the physical hazards criteria would:

  • Incorporate the current HCS definitions of flammable liquid and gas into PSM and health hazard into Hazardous Waste Operations and Emergency Response (HAZWOPER);
  • Change paragraphs on flammable and combustible liquids to conform in categories, terminology, flashpoints (FP) and boiling points (BP) to the GHS modifications to HCS;
  • Update the acceptable methods for determining flashpoints;
  • Modify the welding standard § 1910.252 requirements on labeling welding consumables to be consistent with GHS modifications to HCS; and
  • Incorporate the modified-HCS definition of flammable aerosols into the Flammable and Combustible Liquids Standard § 1910.106 [35] ; but
  • Leave unchanged electrical standards in Subpart S for general industry and Subpart K for construction, and explosive standards § 1910.109 for general industry and § 1926.914 for construction.

OSHA agrees with the commenters who urged the Agency to ensure consistency in its standards while maintaining their scope (Document ID #s 0049, 0050, 0077, 0105, 0123, 0145, 0163, and 0170). Two standards, PSM and HAZWOPER, rely on definitions from the HCS to define their scope. If OSHA did not modify these standards during this rulemaking, there would be unintended coverage changes. For example, PSM covers processes that involve “flammable liquids” as currently defined by reference to the HCS which are limited to liquids with a flashpoint below 100 °F. However, the proposal incorporates the GHS definitions for physical hazards and defines flammable liquids as liquids with a flashpoint below 199.4 °F, potentially increasing the coverage of PSM by adding flammable liquids with flashpoints between 100 °F and 199.4 °F to the chemicals PSM already covers. Therefore, OSHA is proposing to change the PSM standard to define “flammable liquid” by the specific flashpoint set forth in the current HCS, rather than referencing HCS's definition of flammable liquid. Similarly for “flammable gas,” OSHA is proposing to change the definition to only include Category 1 flammable gas to maintain coverage of PSM. Therefore, OSHA would delete the reference to HCS for flammable liquid and insert the current definition in paragraph 1910.119(a)(1)(ii). The current PSM standard states:

(ii) A process which involves a flammable liquid or gas (as defined in 1910.1200(c) of this part) on site in one location, in a quantity of 10,000 pounds (4535.9 kg) * * *

The new proposed paragraph would state:

(ii) A process which involves a Category 1 flammable gas (as defined in 1910.1200 (c)) or flammable liquid with a flashpoint below 100 °F (37.8 °C) on site in one location, in a quantity of 10,000 pounds (4535.9 kg) * * *

Likewise, OSHA is proposing to update the definition of health hazard in HAZWOPER 1910.120 so the terminology is aligned with the GHS health hazards in Appendix A. The new definition would read:

Health hazard means a chemical or a pathogen where acute or chronic health effects may occur in exposed employees. It also includes stress due to temperature extremes. The term “health hazard” includes chemicals which are classified in accordance with the Hazard Communication standard, 29 CFR 1910.1200 as posing one of the following hazardous effects: Acute toxicity (any route of exposure); skin corrosion or irritation; serious eye damage or eye irritation; respiratory or skin sensitization; germ cell mutagenicity; carcinogenicity; reproductive toxicity; target organ specific systemic toxicity (single or repeated dose); or aspiration toxicity. The criteria for determining whether a chemical is classified as a health hazard can be found in Appendix A to 29 CFR 1910.1200.

OSHA was concerned that some of the terminology in HAZWOPER, such as neurotoxin and nephrotoxin (see definitions in “health hazard”) which are partly defined by reference to the HCS would no longer be consistent with the modified HCS. OSHA has not dropped these health hazards, but instead, consistent with the GHS modifications to HCS, such terms are recatagorized under specific target organ toxicity, thus maintaining the same requirements for hazard communication. If OSHA did not update the definition in HAZWOPER then employers would not have the proper guidance on how to classify a health hazard consistent with the GHS.

Flammable and Combustible Liquids

OSHA is proposing to align the definitions of flammable and combustible liquids to conform to the GHS modifications to HCS in categories, terminology, flashpoints, and boiling points, in the general industry, construction, and maritime standards. (See Table XV-3 for comparison of the current HCS definitions and the GHS flammable liquid definitions.) OSHA believes that most of the changes in the definitions are not significant. OSHA is proposing to make nominal changes to the flashpoint values for flammable and combustible liquids from 22.8 ° C to 23 °C and 93.3 °C to 93 °C to be consistent with the GHS modifications to HCS. OSHA believes these changes represent simple rounding to the closest significant value and that they will have no effect on the scope of its standards or safety, but will enable users to work in whole numbers, which OSHA believes will benefit affected employers and employees.

However, other changes are potentially significant. The boiling points used to define the threshold for the current Flammable Class IA will shift from the cut-point of 37.8 °C to a cut-point of 35 °C for Category 1 in the modified HCS. Flammable Class IA is currently defined as any liquid with a FP of greater than () 22.8 °C and a BP of less than () 37.8 °C; the new definition will adopt a BP of less than or equal to (≤) 35 ° C. Likewise, the BP will shift for the current definition of Flammable Class IB from equal to or greater than (≥) 37.8 °C to () 35 °C for Category 2. These changes are necessary to make OSHA standards internally consistent and consistent with the GHS modifications to HCS. However, OSHA is concerned that changing the boiling point cut-off for the highly flammable liquids currently classified as Flammable IA could, under the GHS modifications to HCS, lead to a subset of these chemicals being classified as GHS Category 2 Flammable Liquids. Since some of the storage and handling requirements are based on the hazard category, a facility could increase the size of its storage tanks for the liquids with boiling points between 37.8 °C and 35 °C. It is possible that increasing the size for these chemicals could decrease the safety of their storage. OSHA has reviewed the properties related to the flammability of approximately 900 chemical substances (754 liquids) listed in the CRC Handbook of Chemistry and Physics [ 85th edition]. Approximately 1 percent of this list of flammable liquids would result in a reclassification from the current Flammable and Combustible Liquids Standard Class IA to GHS Category 2. While this is a small percentage of the total flammable liquids, it represents approximately 15 percent of the current Flammable and Combustible Liquids Standard Class IA liquids on this list. This is an instance where the benefits of harmonization could be in conflict with the measure of safety currently provided.

How the storage and handling of chemicals would be affected by the changes in classification of chemicals generated significant comments to the ANPR. Some commenters urged the Agency to change criteria in the standards, but acknowledged that the storage and handling requirements for flammable liquids would present the most critical potential problems (Document ID #s 0072, 0102, 0179, 0034, 0145, and 0163). Other commenters were concerned that changing the definitions, including flammability criteria, would require facilities to modify their storage facilities to maintain compliance with § 1910.106, with some worried that storage receptacles would have to be smaller, leading to less storage and greater costs. For example, BASF wrote:

The flammable and combustible liquid standard, 29 CFR 1910.106, includes definitions within the standard. Changing these to be consistent with the GHS definitions could require storage facilities to be modified or the amount of storage inventory limited, all of which impacts the cost of implementation. (Document ID # 0119)

OSHA disagrees with this statement. Because the GHS change from OSHA's flammable and combustible classes to GHS Categories involves a lowering of the boiling point cut-offs by 2.8 °C, all current handling and storage would be permitted. In addition, storage and handling of chemicals whose boiling points fall between 37.8 °C and 35 °C would be allowed to be stored according to the lesser flammability Category 2. Category 2 chemicals could be stored in larger containers but, as noted above, it is possible that safety could be compromised. OSHA is proposing the GHS changes to the safety standards because it believes safety will be enhanced by the standardization of the GHS modifications. However, OSHA is seeking comment on the resulting handling and storage of chemicals after the standards have incorporated GHS definitions, and the Agency has included this topic in Section II (Issues) of this preamble.

OSHA is also proposing to adopt the terminology in the GHS modifications to HCS so that all liquids covered by § 1910.106 will be redefined as flammable liquids in Categories 1-4, as appropriate, and the term “Combustible Liquids” in §§ 1910.106, 1910.107, 1910.123, 1910.125, 1926.152, and 1926.155 will be deleted. Instead of using the term Combustible Class IIIB, flammable liquids with a flashpoint of ≥ 93 °C will be called “Flammable Liquids with a Flashpoint of 93 °C.” The GHS does not classify flammable liquids with flashpoints 93 °C and, in fact, does not use the term combustible liquid for classification. However, other OSHA standards, such as § 1910.107, Spray Finishing Using Flammable and Combustible Materials, relying on the current § 1910.106 definitions of flammable and combustible liquids, which cover liquids with a flashpoint over 93 °C as “combustible liquids.” OSHA believes it needs to maintain this non-GHS category in order to preserve the coverage of combustibles in standards such as Spray Finishing. However, these chemicals will be known by the new term “Flammable Liquids with a Flashpoint of Greater Than 93°C,” which means that protection provided by the current standards remains in force.

Updating the Method To Determine Flashpoint

Currently, OSHA references only ASTM D-56-70 or ASTM D-93-71 for testing methods to determine flashpoints for liquids and these are the only methods allowed. However, these methods, which were developed in 1970 and 1971, have been updated and are incompatible with GHS. To remedy this situation, OSHA is proposing to reference the methods set forth in the GHS that can be used to determine flashpoints. These methods include updated ASTM methods, ISO methods, as well as British, French, and German national standards for the testing. A complete list of methods is in the Globally Harmonized System of Classification and Labelling of Chemicals (GHS) (second revision, 2007). OSHA is seeking comment on this approach, and the Agency has included this topic in Section II (Issues) of this preamble.

Welding, Cutting and Brazing

OSHA is proposing to modify the labeling requirements for welding consumables in the Welding, Cutting and Brazing Standard, paragraphs 1910.252(c)(iv)(A), (B), and (C). These paragraphs contain the labeling requirements for filler metals, fusible granular materials and fluxes. The standard sets forth the responsibility for labeling in paragraph 1910.252(c)(iv):

The suppliers of welding materials shall determine the hazard, if any associated with the use of their materials in welding, cutting, etc.

Similar to the substance-specific health standards, OSHA is proposing to require these labels to be consistent with the GHS modifications to HCS.

Flammable Aerosols

OSHA is proposing to harmonize its existing standards with the GHS modifications to HCS on flammable aerosols. Currently OSHA references CPSC regulations for its definition of flammable aerosol. The current HCS definition is:

“Aerosol, flammable” means an aerosol that, when tested by the method described in 16 CFR 1500.45, yields a flame projection exceeding 18 inches at full valve opening, or a flashback (a flame extending back to the valve) at any degree of valve opening.

OSHA defines and regulates flammable aerosols in its Flammable and Combustible Liquids standard at 29 CFR 1910.106. The definitions there are:

Aerosol shall mean a material which is dispensed from its container as a mist, spray, or foam by a propellant under pressure. § 1910.106(a)(1).

Flammable aerosol shall mean an aerosol which is required to be labeled “Flammable” under the Federal Hazardous Substances Labeling Act (15 U.S.C. 1261). For the purposes of paragraph (d) of this section, such aerosols are considered Class IA liquids. § 1910.106(a)(13).

Appendix B.3 of GHS modifications to HCS begins its definition with what an aerosol is:

* * * any non-refillable receptacle containing a gas compressed, liquefied or dissolved under pressure, and fitted with a release device allowing the contents to be ejected as particles in suspension in a gas, or as a foam, paste, powder, liquid or gas. (Appendix B)

Aerosols are then further classified into one of two categories if it contains a flammable liquid, gas or solid (Appendix B.3.2.1).

OSHA's decision to change the definition of aerosols to be consistent with the GHS is based not only upon harmonizing its own standards with those followed by other countries who have or are considering adopting GHS, but also with making OSHA standards internally consistent. OSHA believes that the classification resulting from the various methods are similar enough that all aerosols currently regulated by OSHA would continue to be so and that few, if any, new aerosols would be subject to OSHA regulation. Thus, OSHA is proposing to remove the current definitions from its Flammable and Combustible Liquids standards and insert its GHS consistent definitions along with references to Appendix B.3 of the HCS. While the Agency believes the effect of these changes will be minimal, it nevertheless seeks comment on this change which will primarily affect the Flammable and Combustible Liquids standards.

Standards Not Included in This Rulemaking

At this time, OSHA is not proposing to change standards that incorporate by reference other consensus standards, such as NFPA codes, or are based on consensus standards when those consensus standards are used for internal design criteria only and do not reference HCS for applicable scope or incorporation into the SDS. These standards would include subpart S—Electrical in part 1910 (General industry) and Subpart K—Electrical in part 1926 (Construction). Many commenters were particularly concerned that a change in OSHA's definitions would create an incompatibility with local building codes (Document ID #s 0047, 0075, 0076, 0104, 0113, 0145 and 0163). In many cases, this would require extensive rewiring to meet the subpart S requirements on hazardous locations and would lead to conflicts with local electrical codes.

In addition OSHA is not proposing to update standards that pertain to explosives at this time. A separate rulemaking to revise the Explosive and Blasting Agents standard § 1910.109 is currently in progress.

XVI. References Back to Top

Abt Associates, Inc., 1999. Consumer labeling initiative: Phase II report. U.S. Environmental Protection Agency.

Adams, A., S. Bochner, and L. Bilik, 1998. The effectiveness of warning signs in hazardous work places: Cognitive and social determinants. Applied Ergonomics 29(4): 247-254.

Akerboom, S. and M. Trommelen, 1998. Environmental labeling on household chemicals: Comprehensibility and impact on warning information. International Journal of Cognitive Ergonomics 2(1-2): 107-122.

[ANSI] American National Standards Institute, 2002a. American National Standard Criteria for Safety Symbols. ANSI Z535.3-2002.

[ANSI] American National Standards Institute, 2002b. American National Standard for Environmental and Facility Safety Signs. ANSI Z535.2-2002.

[ANSI] American National Standards Institute, 2002c. American National Standard for Product Safety Signs and Labels. ANSI Z535.4-2002.

[ANSI] American National Standard Institute, 2004. American National Standard for Hazardous Industrial Chemicals—Material Safety Data Sheets—Preparation. ANSI Z400.1-2004.

[ANSI] American National Standard Institute, 2006. American National Standard for Hazardous Industrial Chemicals—Precautionary Labeling. ANSI Z129.1-2006.

Banda, S.F. and K. Sichilongo, 2006. Analysis of the level of comprehension of chemical hazard labels: A case for Zambia. Science of the Total Environment 363(1-3): 22-27.

Beach, J., 2002. The problem with material safety data sheets. Occupational Medicine (London) 52(2): 67-68.

[BLS] U.S. Bureau of Labor Statistics. 2008. Nonfatal occupational illnesses by major industry sector and category of illness, private industry, 2007. Available at: http://www.bls.gov/iif/oshwc/osh/os/ostb1911.pdf

[BLS] U.S. Bureau of Labor Statistics. 2009. Number of nonfatal occupational injuries and illnesses involving days away from work by industry and selected sources of injury or illness, 2007. Available at: http://www.bls.gov/iif/oshwc/osh/case/ostb1945.pdf

Bowles, C.T., A.D. Fisk, and W.A. Rogers, 2002. Inference and the use of similes and metaphors in warnings. Proceedings of the Human Factors and Ergonomics Society 46th Annual Meeting: 1703-1707.

Braun, C.C., L. Sansing, and N.C. Silver, 1994. The interaction of signal word and color on warning labels: Differences in perceived hazard. Proceedings of the Human Factors and Ergonomics Society 38th Annual Meeting: 831-835.

Braun, C.C., S.A. Glusker, R.S. Holt, and N.C. Silver, 1995. Adding consequence information to product instructions: Changes in hazard perceptions. Proceedings of the Human Factors and Ergonomics Society 39th Annual Meeting: 346-350.

Conklin, J., 2003. An international assessment of the comprehensibility of material safety data sheets (MSDSs). DPH dissertation, University of Texas Health Science Center at Houston, School of Public Health.

Dowse, R. and M. Ehlers, 2005. Medicine labels incorporating pictograms: Do they influence understanding and adherence? Patient Education and Counseling 58(1): 63-70.

Drake, K.L., V.C. Conzola, and M.S. Wogalter, 1998. Discrimination among sign and label warning signal words. Human Factors and Ergonomics in Manufacturing 8(4): 289-301.

Dunlap, G.L., R.E. Granda, and M.S. Kustas, 1986. Observer perceptions of implied hazard: safety signal word and color words. IBM Technical Report (T 00.3428). As reported in Sattler, B., B. Lippy, and T.G. Jordan, 1997. Hazard communication: A review of the science underpinning the art of communication for health and safety.

[ERG] Eastern Research Group, 2007. Hazard communication: An updated review of the science of health and safety communication. Report submitted to OSHA Directorate of Standards and Guidance.

Evans, A.W., R.M. Hoeft, F.G. Jentsch, and C.A. Bowers, 2002. Is a picture worth a thousand words? Investigating structural knowledge with textual and pictorial stimuli. Proceedings of the Human Factors and Ergonomics Society 46th Annual Meeting: 240-244.

Frantz, J.P., J.M. Miller, and M.R. Lehto, 1994. Must the context be considered when applying generic safety symbols: A case study in flammable contact adhesives. As reported in Sattler, B., B. Lippy, and T.G. Jordan, 1997. Hazard communication: A review of the science underpinning the art of communication for health and safety.

Frazier, L.M., B.W. Beasley, G.K. Sharma, and A.A. Mohyuddin, 2001. Health information in material safety data sheets for a chemical which causes asthma. Journal of General Internal Medicine 16(2): 89-93.

Freeman, K.S., 2001. Health and safety information for specialized vocational audiences. Proceedings/STC, Society for Technical Communication Annual Conference, 2001: 537-542.

Ganier, F., 2001. Processing text and pictures in procedural instructions. Information Design Journal 10: 146-153. Cited in: Warning symbols by M.S. Wogalter, N.C. Silver, S.D. Leonard, and H. Zaikina, 2006b. In M.S. Wogalter (ed.), Handbook of Warnings (159-176). Mahwah, NJ: Lawrence Erlbaum Associates, Inc., 2006.

[GAO] U.S. General Accounting Office. 1991. OSHA action needed to improve compliance with hazard communication standard. GAO/HRD-92-8. Available at http://www.gao.gov/.

[GAO] U.S. General Accounting Office. 1992. Employers' experience in complying with the hazard communication standard. GAO/HRD-92-63BR. Available at http://www.gao.gov/.

Griffith, L.J. and S.D. Leonard, 1997. Association of colors with warning signal words. International Journal of Industrial Ergonomics 20(4): 317-325.

Hanson, J., 2004. Statement before the U.S. Senate Subcommittee on Employment, Safety, and Training during its hearing on “Hazard Communication in the 21st Century Workforce.” 25 March 2004.

Hellier, E., D. Wright, and J. Edworthy, 2000a. Investigating the perceived hazard of warning signal words. Risk, Decision and Policy 5: 39-48.

Hellier, E., D.B. Wright, J. Edworthy, and S. Newstead, 2000b. On the stability of the arousal strength of warning signal words. Applied Cognitive Psychology 14(6): 577-592.

Hemenway, D., 1975. Industrywide Voluntary Product Standards. Cambridge, MA: Ballinger Publishing Company.

Herbert R. and P.J. Landrigan. 2000. Work-related death: a continuing epidemic. Am J Public Health 90(4): 541-5.

Houts, P.S., J.T. Witmer, H.E. Egeth, M.J. Loscalzo, and J.R. Zabora, 2001. Using pictographs to enhance recall of spoken medical instructions II. Patient Education and Counseling 43(3): 231-242.

[ISO] International Organization for Standardization, 2007. Graphical Symbols—Test Methods—Part 1: Methods for Testing Comprehensibility. ISO 9186-1.

Jaynes, L.S., and D.B. Boles, 1990. The effect of symbols on warning compliance. Proceedings of the Human Factors Society 34th Annual Meeting (2): 984-987.

Kalsher, M.J., M.S. Wogalter, and B.M. Racicot, 1996. Pharmaceutical container labels and warnings: Preference and perceived readability of alternative designs and pictorials. International Journal of Industrial Ergonomics 18: 83-90.

Kalsher, M.J. and K.J. Williams, 2006. Behavioral compliance: Theory, methodology, and results. In M.S. Wogalter (ed.), Handbook of Warnings (313-332). Mahwah, NJ: Lawrence Erlbaum Associates, Inc.

Karstadt, M. 1988. Final Report. Report prepared for OSHA under contract 816605. Docket H022D, Ex. 4-203.

Kearney/Centaur. 1991a. The accuracy of material safety data sheets. Report prepared for OSHA under contract J-9-F-8-0019. The results of this study were later published as: Kolp, P.W., P.L. Williams, and R.C. Burtan. 1995. Assessment of the accuracy of material safety data sheets. Am Ind Hyg Assoc J 56:178-183.

Kearney/Centaur. 1991b. The comprehensibility of material safety data sheets. Report prepared for OSHA under contract J-9-F-8-0019. The results of this study were later published as: Kolp, P., B. Sattler, M. Blayney, and T. Sherwood. 1993. Comprehensibility of material safety data sheets. Am J Ind Med 23: 135-141.

Landrigan P.J. and S. Markowitz. 1989. Current magnitude of occupational disease in the United States. Estimates from New York State. Ann N Y Acad Sci 572:27-45; discussion 55-60.

Laughery, K.R., S.L. Young, K.P. Vaubel, and J.W. Brelsford, 1993. The noticeability of warnings on alcoholic beverage containers. Journal of Public Policy Marketing 12(1): 38.

Lehto, M.R., 1998. The influence of chemical warning label content and format on information retrieval speed and accuracy. Journal of Safety Research 29(1): 43-56.

Leigh J.P., S.B. Markowitz, M. Fahs, C. Shin, P.J. Landrigan. Occupational injury and illness in the United States. Estimates of costs, morbidity, and mortality. 1997. Arch Intern Med 157(14):1557-68.

Lesch, M.F., 2002. Signs of age in today's workforce. Occupational Health Safety 71(12): 45.

Lesch, M.F., 2003. Comprehension and memory for warning symbols: Age-related differences and impact of training. Journal of Safety Research 34(5): 495-505.

Lexington Group. 1999. Summary report on the evaluation of the accuracy of first aid information on material safety data sheets. Report prepared under contract to OSHA Directorate of Technical Support.

London, L., 2003. FRIDGE/UNITAR study into the implications of implementing the Globally Harmonised System of Classification and Labelling of Chemicals and development of an implementation strategy for South Africa. National Economic Development Labour Council (NEDLAC), Johannesburg, South Africa. Parts 2 and 3. Available online at http://www.nedlac.org.za/. Last accessed 4 June 2007.

Meingast, M., 2001. Increasing attention and retention of warnings: Effects of container hazardousness, warning quality, and severity of injury. Proceedings of the Human Factors and Ergonomics Society 45th Annual Meeting: 1482-1486.

NACOSH Haz Com Workgroup. 1996. National Advisory Committee on Occupational Safety and Health, Report to OSHA on Hazard Communication. Available at: http://www.osha.gov/SLTC/hazardcommunications/wgfinal.html

Niemeier, R. 1997. NIOSH, Education and Information Division. Personal Communication with Bruce Lippy. (May 20, 1995). As reported in Sattler, B., B. Lippy, and T.G. Jordan, 1997. Hazard communication: A review of the science underpinning the art of communication for health and safety.

[OSHA] U.S. Occupational Safety and Health Administration, 2004. Hazard Communication in the 21st Century Workplace. March 2004. Available online at http://www.osha.gov/dsg/hazcom/finalmsdsreport.html. Last accessed 6 July 2007.

Parsons, S.O., J.L. Seminara, and M.S. Wogalter, 1999. Summary of warnings research. Ergonomics in Design 7(1): 21-31.

Paul M, and S. Kurtz. 1994. Analysis of reproductive health hazard information on material safety data sheets for lead and the ethylene glycol ethers. Am J Ind Med. 25(3):403-15.

Phillips, C.C., 1997. The efficacy of material safety data sheets and worker acceptability. Ph.D. dissertation, University of Tennessee at Knoxville. May 1997. Cited in: Hazard communication: A review of the science underpinning the art of communication for health and safety by B. Sattler, B. Lippy, and T.G. Jordan, 1997. Available online at http://www.osha.gov/SLTC/hazardcommunications/hc2inf2.html. Last accessed 6 June 2007.

Phillips, C.C., B.C. Wallace, C.B. Hamilton, R.T. Pursley, G.C. Petty, and C.K. Bayne, 1999. The efficacy of material safety data sheets and worker acceptability. Journal of Safety Research 30(2): 113-122.

[PIA] Printing Industries of America, Inc. 1990. Comments of the Printing Industries of America on the OSHA Hazard Communication Standard. Docket H-022G Ex. 2-313.

Policy, Planning, and Evaluation, Inc. (PPE), December 31, 2008. Final Report: Data and Analysis in Support of an Economic Analysis of Proposed Changes to the OSHA Hazard Communication Standard. Prepared under Contract to Office of Regulatory Analysis, OSHA.

Rogers, W.A., N. Lamson, and G.K. Rousseau, 2000. Warning research: an integrative perspective. Human Factors 42: 102-139.

Sansgiry, S.S., P.S. Cady, and B.A. Adamcik, 1997. Consumer comprehension of information on over-the-counter medication labels: effects of picture superiority and individual differences based on age. Journal of Pharmaceutical Marketing Management 11(3): 63-76.

Sattler, B., B. Lippy, and T.G. Jordan, 1997. Hazard communication: A review of the science underpinning the art of communication for health and safety. Available online at http://www.osha.gov/SLTC/hazardcommunications/hc2inf2.html. Last accessed 6 June 2007.

Silver, N.C., and Wogalter, M.S., 1993. Broadening the range of signal words. Human factors perspectives on warnings. California: The Human Factors and Ergonomics Society: 186-190.

Smith-Jackson, T. and M.S. Wogalter, 1998. Determining the preferred order of material safety data sheets (MSDS): A user-centered approach. Proceedings of the Human Factors and Ergonomics Society 42nd Annual Meeting: 1073-1077.

Smith-Jackson, T.L. and M.S. Wogalter, 2000. Users' hazard perceptions of warning components: An examination of colors and symbols. Proceedings of the XIVth Triennial Congress of the International Ergonomics Association and 44th Annual Meeting of the Human Factors and Ergonomics Association, Ergonomics for the New Millennium: 55-58.

Sojourner, R.J. and M.S. Wogalter, 1997. The influence of pictorials on evaluations of prescription medication instructions. Drug Information Journal 31: 963-972.

Sojourner, R.J. and M.S. Wogalter, 1998. The influence of pictorials on the comprehension and recall of pharmaceutical safety and warning information. International Journal of Cognitive Ergonomics 2(1-2): 93-106.

[SOT] Society of Toxicology, 2007. A new language for toxicologists: Globally Harmonized System of Classification and Labelling of Chemicals (GHS). Comments prepared on behalf of the Society of Toxicology by members of the Occupational and Public Health Specialty Section.

Swindell, J., 1999. Measuring visual search reaction time and accuracy for a product label warning as a function of icon, color, column and vertical placement. M.S. dissertation, North Carolina State University.

United Nations, 2002. Safety Data Sheet for Chemical Products—Part 1: Content and Order of Sections. Draft Standard: ISO/WD 11014-1. Sub-committee of experts on the GHS of classification and labeling of chemicals. UN/GHS-SC/4/INF.14. Available online at http://www.unece.org/trans/doc/2002/ac10c4/UN-SCEGHS-04-inf14e.doc. Last accessed 6 June 2007.

United Nations, 2007. Globally Harmonized System of Classification and Labeling of Chemicals (GHS). Available online at http://www.unece.org/trans/danger/publi/ghs/ghs_rev02/02files_e.html. Last accessed 22 September 2008.

University of California Centers for Occupational and Environmental Health (COEH), 2008. Green Chemistry: Cornerstone to a Sustainable California. http://www.coeh.ucla.edu/greenchemistry.pdf.

U.S. Chemical Safety and Hazard Investigation Board, February 2005. Investigation Report: Combustion Dust Fire and Explosions. Report No. 2003-09-I-KY.

Wogalter, M.S., Jarrad, S.W., and Simpson, S.N., 1992. Effects of warning signal words on consumer-product hazard perceptions. Proceedings of the Human Factors Society, 36th annual Meeting: 935-939.

Wogalter, M.S., M.J. Kalsher, and B. Racicot, 1993. Behavioral compliance with warnings: Effects of voice, context, and location. Safety Science 16(5-6): 637-654.

Wogalter, M.S., P.B. Begley, L.F. Scancorelli, and J.W. Brelsford, 1997a. Effectiveness of elevator service signs: Measurement of perceived understandability, willingness to comply and behaviour. Applied Ergonomics 28(3): 181-187.

Wogalter, M.S., L.J. Frederick, A.B. Magurno, and O.L. Herrera, 1997b. Connoted hazard of Spanish and English warning signal words, colors, and symbols by native Spanish language users. Proceedings of the 13th Triennial Congress of the International Ergonomics Association 3: 353-355. Cited in: Users' hazard perceptions of warning components: An examination of colors and symbols by T.L. Smith-Jackson and M.S.

Wogalter, 2000. Proceedings of the XIVth Triennial Congress of the International Ergonomics Association and 44th Annual Meeting of the Human Factors and Ergonomics Association, Ergonomics for the New Millennium: 55-58.

Wogalter, M.S., R.J. Sojourner, and J.W. Brelsford, 1997c. Comprehension and retention of safety pictorials. Ergonomics 40(5): 531-542.

Wogalter, M.S., M.J. Kalsher, L.J. Frederick, A.B. Magurno, and B.M. Brewster, 1998. Hazard level perceptions of warning components and configurations. International Journal of Cognitive Ergonomics 2(1-2): 123-143.

Wogalter, M.S., N.C. Silver, S.D. Leonard, and H. Zaikina, 2006. Warning symbols. In M.S. Wogalter (ed.), Handbook of Warnings (159-176). Mahwah, NJ: Lawrence Erlbaum Associates, Inc.

Young, S.L., 1998. Connotation of hazard for signal words and their associated panels. Applied Ergonomics 29(2): 101-110.

XVII. Authority and Signature Back to Top

This document was prepared under the direction of Jordan Barab, Acting Assistant Secretary of Labor for Occupational Safety and Health, U.S. Department of Labor, 200 Constitution Avenue, NW., Washington, DC 20210. It is issued under the authority of sections 4, 6, and 8 of the Occupational Safety and Health Act of 1970 (29 U.S.C. 653, 655, 657); 5 U.S.C. 553; Section 304, Clean Air Act Amendments of 1990 (101, reprinted at 29 U.S.C.A. 655 Note); Section 41, Longshore and Harbor Workers' Compensation Act (33 U.S.C. 941); Section 107, Contract Work Hours and Safety Standards Act (40 U.S.C. 3704); Section 1031, Housing and Community Development Act of 1992 (42 U.S.C. 4853); Section 126, Superfund Amendments and Reauthorization Act of 1986, as amended (reprinted at 29 U.S.C.A. 655 Note); Secretary of Labor's Order No. 5-2007 (72 FR 31160); and 29 CFR part 1911.

Signed at Washington, DC, this 10th day of September 2009.

Jordan Barab,

Acting Assistant Secretary of Labor.

XVIII. Proposed Amendments Back to Top

List of Subjects Back to Top

begin regulatory text

PART 1910—OCCUPATIONAL SAFETY AND HEALTH STANDARDS [AMENDED] Back to Top

Subpart A—[Amended] Back to Top

1. The authority citation for subpart A of part 1910 is revised to read as follows:

Authority:

Sections 4, 6, and 8 of the Occupational Safety and Health Act of 1970 (29 U.S.C. 653, 655, 657); Secretary of Labor's Order No. 12-71 (36 FR 8754), 8-76 (41 FR 25059), 9-83 (48 FR 35736), 1-90 (55 FR 9033), 6-96 (62 FR 111), 3-2000 (65 FR 50017), 5-2002 (67 FR 65008), or 5-2007 (72 FR 31159), as applicable.

Section 1910.6 also issued under 5 U.S.C. 553. Sections 1910.6, 1910.7, and 1910.8 also issued under 29 CFR Part 1911. Section 1910.7(f) also issued under 31 U.S.C. 9701, 29 U.S.C. 9a, 5 U.S.C. 553; Pub. L. 106-113 (113 Stat. 1501A-222); and OMB Circular A-25 (dated July 8, 1993) (58 FR 38142, July 15, 1993).

2. Amend § 1910.6 by adding new paragraphs (h)(22) through (h)(28), (q)(36), (x), and (y) to read as follows:

§ 1910.6 Incorporation by reference.

* * * * *

(h) * * *

(22) ASTM D 56-93, Standard Test Method for Flash Point by Tag Closed Cup Tester, IBR approved for Appendix B to § 1910.1200, (see B.6).

(23) ASTM D 3278-96, Standard Test Method for Flash Point of Liquids by Small Scale Closed-Cup Apparatus, IBR approved for Appendix B to § 1910.1200.

(24) ASTM D 3828-93 Standard Test Method for Flash Point by Small Scale Closed Cup Tester, IBR approved for Appendix B to § 1910.1200,.

(25) ASTM D 93-96, Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester, IBR approved for Appendix B to § 1910.1200.

(26) ASTM D 240-2007 Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter, IBR approved for Appendix B to § 1910.1200.

(27) ASTM D 86-07a Standard Test Method for Distillation of Petroleum Products at Atmospheric Pressure, IBR approved for Appendix B to § 1910.1200.

(28) ASTM D 1078-05 Standard Test Method for Distillation Range of Volatile Organic Liquids, IBR approved for Appendix B to § 1910.1200.

* * * * *

(q) * * *

(36) NFPA 30B-2006 Code for the Manufacture and Storage of Aerosol Products, IBR approved for Appendix B to § 1910.1200.

* * * * *

(x) The following material is available for purchase from the International Standards Organization (ISO) through ANSI, 25 West 43rd Street, Fourth Floor New York, NY 10036-7417.

(1) ISO 10156-1996; “Gases and Gas Mixtures—Determination of Fire Potential and Oxidizing Ability for the Selection of Cylinder Valve Outlets,” IBR approved for Appendix B to § 1910.1200.

(2) EN/ISO 13943-2000, 86.1 to 86.3—Fire Safety—Vocabulary, IBR approved for Appendix B to § 1910.1200

(3) ISO 10156-2-2005 “Gas cylinders—Gases and Gas Mixtures—Part 2: Determination of Oxidizing Ability of Toxic and Corrosive Gases and Gas Mixtures,” IBR approved for Appendix B to § 1910.1200.

* * * * *

(y) The following document is available for purchase from United Nations Publications, 2 United Nations Plaza, Room DC2-853, New York, NY 10017, USA.

(1) The UN Recommendations on the Transport of Dangerous Goods, Manual of Tests and Criteria, Fourth Edition, 2003, IBR approved for Appendix B to § 1910.1200.

(2) [Reserved]

(z) The following is available from Verein Deutscher Ingeniere (VDI)(Association of German Engineers). The guidelines can be ordered at: Beuth Verlag GmbH, 10772 Berlin.

(1) The Grewer Oven test (VDI guideline 2263, part 1, 1990, Test methods for the Determination of the Safety Characteristics of Dusts) with an onset temperature 80 °K (176 °F) above the reference temperature for a volume of 1 l, IBR approved for Appendix B to § 1910.1200, (see B.11).

(2) [Reserved]

(aa) The following journal article can be obtained on-line though Wiley InterScience, at Journal Customer Services, John Wiley Sons, Inc., 350 Main Street, Malden, MA 02148.

(1) The Bulk Powder Screening Test (Gibson, N. Harper, D. J. Rogers, R. Evaluation of the fire and explosion risks in drying powders, Plant Operations Progress, 4 (3), 181-189, 1985) (Copyright 1992 American Institute of Chemical Engineers) with an onset temperature 60°K (140°F) above the reference temperature for a volume of 1 l, IBR approved for Appendix B to § 1910.1200, (see B.11).

(2) [Reserved]

Subpart H—[Amended] Back to Top

3. The authority citation for subpart H is revised to read as follows:

Authority:

Sections 4, 6, and 8 of the Occupational Safety and Health Act of 1970 (29 U.S.C. 653, 655, 657); Secretary of Labor's Order No. 12-71 (36 FR 8754), 8-76 (41 FR 25059), 9-83 (48 FR 35736), 1-90 (55 FR 9033), 6-96 (62 FR 111), 3-2000 (65 FR 50017), or 5-2007 (72 FR 31159), as applicable; and 29 CFR part 1911.

Sections 1910.103, 1910.106 through 1910.111, and 1910.119, 1910.120, and 1910.122 through 1910.126 also issued under 29 CFR part 1911.

Section 1910.119 also issued under Section 304, Clean Air Act Amendments of 1990 (101), reprinted at 29 U.S.C. 655 NOTE. Section 1910.120 also issued under Section 126, Superfund Amendments and Reauthorization Act of 1986 as amended (29 U.S.C. 655 Note), and 5 U.S.C. 553.

4. Amend § 1910.106 as follows:

A. Revise the section heading;

B. Revise paragraphs (a)(13); (a)(14)(i) through (a)(14)(iii) and (a)(19);

C. Remove the last sentence of paragraph (a)(17);

D. Remove and reserve paragraph (a)(18);

E. Remove the words “or combustible” wherever it appears.

F. Remove the words “and combustible” in paragraphs (d)(5)(vi) introductory text, (e)(2) introductory text, (j)(1) and (j)(3);

G. Revise paragraphs (b)(2)(iv)(f) and (g), (b)(2)(vi)(b), (b)(2)(viii)(e), (b)(3)(i), (b)(3)(iv)(a), (b)(3)(iv)(c), (b)(3)(v)(d), (b)(4)(iv)(e), (d)(1)(ii)(b), (d)(2)(iii) and (d)(2)(iii)(a)(2), (d)(3)(i), (d)(4)(iii), (d)(4)(iv), (d)(7)(i)(b), (e)(2), (e)(2)(ii)(b)(1), (e)(2)(ii)(b)(2), (e)(2)(ii)(b)(3), (e)(2)(iv)(a), (e)(2)(iv)(c), (e)(3)(v)(a), (e)(3)(v)(b), (e)(4)(i), (e)(6)(ii), (e)(7)(i)(c), (f)(1)(i), (f)(1)(ii), (f)(2)(ii), (f)(2)(iii)(a), (f)(2)(iii)(b), (f)(2)(iii)(c), (f)(3)(i), (f)(3)(ii), (f)(3)(iv)(a)(1), (f)(3)(iv)(a)(2), (f)(3)(iv)(d)(2), (f)(3)(v), (f)(3)(vi), (f)(4)(viii)(e), (f)(5)(i), (f)(6), (f)(8), (g)(1)(i)(c), (g)(1)(i)(e), (g)(1)(i)(f), (g)(1)(iii)(a), (g)(1)(iii)(b), (g)(1)(iii)(c), (g)(1)(v), (g)(3)(iv)(a), (g)(3)(iv)(b)(1), (g)(3)(iv)(b)(2), (g)(3)(iv)(c), (g)(3)(v)(a), (g)(3)(vi)(a), (g)(4)(iii)(d), (g)(5)(i), (g)(6)(iv), (g)(7), (h)(3)(i)(a), (h)(3)(iii)(b), (h)(3)(iv), (h)(5), (h)(7)(i)(b), (h)(7)(iii)(c), (j), and Tables H-12, H-14 through H-17, and H-19;

The revisions read as follows:

§ 1910.106 Flammable liquids.

* * * * *

(a) * * *

(13) Flammable aerosol shall mean a flammable aerosol as defined by Appendix B to § 1910.1200—Physical Hazard Criteria. For the purposes of paragraph (d) of this section, such aerosols are considered Category 1 flammable liquids.

(14) * * *

(i) For a liquid which has a viscosity of less than 45 SUS at 100 ºF (37.8 °C), does not contain suspended solids, and does not have a tendency to form a surface film while under test, the procedure specified in the Standard Method of Test for Flashpoint by Tag Closed Tester (ASTM D-56-70), which is incorporated by reference as specified in Sec. 1910.6, shall be used or an equivalent test method as defined in Appendix B to § 1910.1200—Physical Hazard Criteria.

(ii) For a liquid which has a viscosity of 45 SUS or more at 100 °F (37.8 °C), or contains suspended solids, or has a tendency to form a surface film while under test, the Standard Method of Test for Flashpoint by Pensky-Martens Closed Tester (ASTM D-93-71) shall be used or an equivalent method as defined by Appendix B to § 1910.1200—Physical Hazard Criteria, except that the methods specified in Note 1 to section 1.1 of ASTM D-93-71 may be used for the respective materials specified in the NOTE: The preceding ASTM standards are incorporated by reference as specified in § 1910.6.

(iii) For a liquid that is a mixture of compounds that have different volatilities and flashpoints, its flashpoint shall be determined by using the procedure specified in paragraph (a)(14)(i) or (ii) of this section on the liquid in the form it is shipped.

* * * * *

(18) [Reserved]

(19) Flammable liquid means any liquid having a flashpoint at or below 199.4 °F (93 °C). Flammable liquids are divided into four categories as follows:

(i) Category 1 shall include liquids having flashpoints below 73.4 °F (23 °C) and having a boiling point at or below 95 °F (35 °C).

(ii) Category 2 shall include liquids having flashpoints below 73.4 °F (23 °C) and having a boiling point above 95 °F (35 °C).

(iii) Category 3 shall include liquids having flashpoints at or above 73.4 °F (23 °C) and at or below 140 °F (60 °C). When a Category 3 liquid with a flashpoint at or above 100 °F (37.8 °C) is heated for use to within 30 °F (16.7 °C) of its flashpoint, it shall be handled in accordance with the requirements for a Category 3 liquid with a flashpoint below 100 °F (37.8 °C).

(iv) Category 4 shall include liquids having flashpoints above 140 °F (60 °C) and at or below 199.4 °F (93 °C). When a Category 4 flammable liquid is heated for use to within 30 °F (16.7 °C) of its flashpoint, it shall be handled in accordance with the requirements for a Category 3 liquid with a flashpoint at or above 100 °F (37.8 °C).

(v) When liquid with a flashpoint greater than 199.4 °F (93 °C) is heated for use to within 30 °F (16.7 °C) of its flashpoint, it shall be handled in accordance with the requirements for a Category 4 flammable liquid.

* * * * *

(b) * * *

(2) * * *

(iv) * * *

(f) Tanks and pressure vessels storing Category 1 flammable liquids shall be equipped with venting devices which shall be normally closed except when venting to pressure or vacuum conditions. Tanks and pressure vessels storing Category 2 flammable liquids and Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C) shall be equipped with venting devices which shall be normally closed except when venting under pressure or vacuum conditions, or with approved flame arresters.

Exemption: Tanks of 3,000 bbls. capacity or less containing crude petroleum in crude-producing areas; and, outside aboveground atmospheric tanks under 1,000 gallons capacity containing other than Category 1 flammable liquids may have open vents. (See paragraph (vi) (b) of this section.)

(g) Flame arresters or venting devices required in paragraph (f) of this section may be omitted for Category 2 flammable liquids and Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C) where conditions are such that their use may, in case of obstruction, result in tank damage.

* * * * *

(vi) * * *

(b) Where vent pipe outlets for tanks storing Category 1 or 2 flammable liquids, or Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C), are adjacent to buildings or public ways, they shall be located so that the vapors are released at a safe point outside of buildings and not less than 12 feet above the adjacent ground level. In order to aid their dispersion, vapors shall be discharged upward or horizontally away from closely adjacent walls. Vent outlets shall be located so that flammable vapors will not be trapped by eaves or other obstructions and shall be at least five feet from building openings.

* * * * *

(viii) * * *

(e) For Category 2 flammable liquids and Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C), other than crude oils, gasolines, and asphalts, the fill pipe shall be so designed and installed as to minimize the possibility of generating static electricity. A fill pipe entering the top of a tank shall terminate within 6 inches of the bottom of the tank and shall be installed to avoid excessive vibration.

* * * * *

(3) * * *

(i) Location. Excavation for underground storage tanks shall be made with due care to avoid undermining of foundations of existing structures. Underground tanks or tanks under buildings shall be so located with respect to existing building foundations and supports that the loads carried by the latter cannot be transmitted to the tank. The distance from any part of a tank storing Category 1 or 2 flammable liquids, or Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C), to the nearest wall of any basement or pit shall be not less than 1 foot, and to any property line that may be built upon, not less than 3 feet. The distance from any part of a tank storing Category 3 flammable liquids with a flashpoint at or above 100 °F (37.8 °C) or Category 4 flammable liquids to the nearest wall of any basement, pit or property line shall be not less than 1 foot.

* * * * *

(iv) * * *

(a) Location and arrangement of vents for Category 1 or 2 flammable liquids, or Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C). Vent pipes from tanks storing Category 1 or 2 flammable liquids, or Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C), shall be so located that the discharge point is outside of buildings, higher than the fill pipe opening, and not less than 12 feet above the adjacent ground level. Vent pipes shall discharge only upward in order to disperse vapors. Vent pipes 2 inches or less in nominal inside diameter shall not be obstructed by devices that will cause excessive back pressure. Vent pipe outlets shall be so located that flammable vapors will not enter building openings, or be trapped under eaves or other obstructions. If the vent pipe is less than 10 feet in length, or greater than 2 inches in nominal inside diameter, the outlet shall be provided with a vacuum and pressure relief device or there shall be an approved flame arrester located in the vent line at the outlet or within the approved distance from the outlet.

* * * * *

(c) Location and arrangement of vents for Category 3 flammable liquids with a flashpoint at or above 100 °F (37.8 °C) or Category 4 flammable liquids. Vent pipes from tanks storing Category 3 flammable liquids with a flashpoint at or above 100 °F (37.8 °C) or Category 4 flammable liquids shall terminate outside of the building and higher than the fill pipe opening. Vent outlets shall be above normal snow level. They may be fitted with return bends, coarse screens or other devices to minimize ingress of foreign material.

* * * * *

(v) * * *

(d) For Category 2 flammable liquids and Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C), other than crude oils, gasolines, and asphalts, the fill pipe shall be so designed and installed as to minimize the possibility of generating static electricity by terminating within 6 inches of the bottom of the tank.

* * * * *

(4) * * *

(iv) * * *

(e) For Category 2 flammable liquids and Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C), other than crude oils, gasoline, and asphalts, the fill pipe shall be so designed and installed as to minimize the possibility of generating static electricity by terminating within 6 inches of the bottom of the tank.

* * * * *

(d) * * *

(1) * * *

(ii) * * *

(b) Category 1, 2, or 3 flammable liquids in the fuel tanks of a motor vehicle, aircraft, boat, or portable or stationary engine;

* * * * *

(2) * * *

(iii) Size. Flammable liquid containers shall be in accordance with Table H-12, except that glass or plastic containers of no more than 1-gallon capacity may be used for a Category 1 or 2 flammable liquid if:

(a) * * *

(2) The user's process either would require more than 1 pint of a Category 1 flammable liquid or more than 1 quart of a Category 2 flammable liquid of a single assay lot to be used at one time, or would require the maintenance of an analytical standard liquid of a quality which is not met by the specified standards of liquids available, and the quantity of the analytical standard liquid required to be used in any one control process exceeds one-sixteenth the capacity of the container allowed under Table H-12 for the category of liquid; or

* * * * *

(3) * * *

(i) Maximum capacity. Not more than 60 gallons of Category 1, 2, or 3 flammable liquids, nor more than 120 gallons of Category 4 flammable liquids may be stored in a storage cabinet.

* * * * *

(4) * * *

(iii) Wiring. Electrical wiring and equipment located in inside storage rooms used for Category 1 or 2 flammable liquids, or Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C), shall be approved under subpart S of this part for Class I, Division 2 Hazardous Locations; for Category 3 flammable liquids with a flashpoint at or above 100 °F (37.8 °C) and Category 4 flammable liquids, shall be approved for general use.

(iv) Ventilation. Every inside storage room shall be provided with either a gravity or a mechanical exhaust ventilation system. Such system shall be designed to provide for a complete change of air within the room at least six times per hour. If a mechanical exhaust system is used, it shall be controlled by a switch located outside of the door. The ventilating equipment and any lighting fixtures shall be operated by the same switch. A pilot light shall be installed adjacent to the switch if Category 1 or 2 flammable liquids, or Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C), are dispensed within the room. Where gravity ventilation is provided, the fresh air intake, as well as the exhaust outlet from the room, shall be on the exterior of the building in which the room is located.

* * * * *

(7) * * *

(i) * * *

(b) At least one portable fire extinguisher having a rating of not less than 12-B units must be located not less than 10 feet, nor more than 25 feet, from any Category 1, 2, or 3 flammable liquid storage area located outside of a storage room but inside a building.

* * * * *

(e) * * *

(2) * * *

(ii) * * *

(b) * * *

(1) 25 gallons of Category 1 flammable liquids in containers

(2) 120 gallons of Category 2, 3, or 4 flammable liquids in containers

(3) 660 gallons of Category 2, 3, or 4 flammable liquids in a single portable tank.

* * * * *

(iv) * * *

(a) Category 1 or 2 flammable liquids, or Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C), shall be kept in covered containers when not actually in use.

* * * * *

(c) Category 1 or 2 flammable liquids, or Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C), may be used only where there are no open flames or other sources of ignition within the possible path of vapor travel.

* * * * *

(3) * * *

(v) * * *

(a) Areas as defined in paragraph (e)(3)(i) of this section using Category 1 or 2 flammable liquids, or Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C), shall be ventilated at a rate of not less than 1 cubic foot per minute per square foot of solid floor area. This shall be accomplished by natural or mechanical ventilation with discharge or exhaust to a safe location outside of the building. Provision shall be made for introduction of makeup air in such a manner as not to short circuit the ventilation. Ventilation shall be arranged to include all floor areas or pits where flammable vapors may collect.

(b) Equipment used in a building and the ventilation of the building shall be designed so as to limit flammable vapor-air mixtures under normal operating conditions to the interior of equipment, and to not more than 5 feet from equipment which exposes Category 1 or 2 flammable liquids, or Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C), to the air. Examples of such equipment are dispensing stations, open centrifuges, plate and frame filters, open vacuum filters, and surfaces of open equipment.

* * * * *

(4) * * *

(i) Tank vehicle and tank car loading or unloading facilities shall be separated from aboveground tanks, warehouses, other plant buildings or nearest line of adjoining property which may be built upon by a distance of 25 feet for Category 1 or 2 flammable liquids, or Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C), and 15 feet for Category 3 flammable liquids with a flashpoint at or above 100 °F (37.8 °C) and Category 4 flammable liquids measured from the nearest position of any fill stem. Buildings for pumps or shelters for personnel may be a part of the facility. Operations of the facility shall comply with the appropriate portions of paragraph (f)(3) of this section.

* * * * *

(6) * * *

(ii) Grounding. Category 1 or 2 flammable liquids, or Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C), shall not be dispensed into containers unless the nozzle and container are electrically interconnected. Where the metallic floorplate on which the container stands while filling is electrically connected to the fill stem or where the fill stem is bonded to the container during filling operations by means of a bond wire, the provisions of this section shall be deemed to have been complied with.

(7) * * *

(i) * * *

(c) Locations where flammable vapor-air mixtures may exist under abnormal conditions and for a distance beyond Division 1 locations shall be classified Division 2 according to the requirements of subpart S of this part. These locations include an area within 20 feet horizontally, 3 feet vertically beyond a Division 1 area, and up to 3 feet above floor or grade level within 25 feet, if indoors, or 10 feet if outdoors, from any pump, bleeder, withdrawal fitting, meter, or similar device handling Category 1 or 2 flammable liquids, or Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C). Pits provided with adequate mechanical ventilation within a Division 1 or 2 area shall be classified Division 2. If Category 3 flammable liquids with a flashpoint at or above 100 °F (37.8 °C) or Category 4 flammable liquids only are handled, then ordinary electrical equipment is satisfactory though care shall be used in locating electrical apparatus to prevent hot metal from falling into open equipment.

* * * * *

(f) * * *

(1) * * *

(i) Category 1 or 2 flammable liquids, or Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C). Category 1 or 2 flammable liquids, or Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C), shall be stored in closed containers, or in storage tanks above ground outside of buildings, or underground in accordance with paragraph (b) of this section.

(ii) Category 3 flammable liquids with a flashpoint at or above 100 °F (37.8 °C) and Category 4 flammable liquids. Category 3 flammable liquids with a flashpoint at or above 100 °F (37.8 °C) and Category 4 flammable liquids shall be stored in containers, or in tanks within buildings or above ground outside of buildings, or underground in accordance with paragraph (b) of this section.

* * * * *

(2) * * *

(ii) Heating. Rooms in which Category 1 or 2 flammable liquids, or Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C), are stored or handled shall be heated only by means not constituting a source of ignition, such as steam or hot water. Rooms containing heating appliances involving sources of ignition shall be located and arranged to prevent entry of flammable vapors.

(iii) * * *

(a) Ventilation shall be provided for all rooms, buildings, or enclosures in which Category 1 or 2 flammable liquids, or Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C), are pumped or dispensed. Design of ventilation systems shall take into account the relatively high specific gravity of the vapors. Ventilation may be provided by adequate openings in outside walls at floor level unobstructed except by louvers or coarse screens. Where natural ventilation is inadequate, mechanical ventilation shall be provided.

(b) Category 1 or 2 flammable liquids, or Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C), shall not be stored or handled within a building having a basement or pit into which flammable vapors may travel, unless such area is provided with ventilation designed to prevent the accumulation of flammable vapors therein.

(c) Containers of Category 1 or 2 flammable liquids, or Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C), shall not be drawn from or filled within buildings unless provision is made to prevent the accumulation of flammable vapors in hazardous concentrations. Where mechanical ventilation is required, it shall be kept in operation while flammable liquids with a flashpoint below 100 °F (37.8 °C) are being handled.

(3) * * *

(i) Separation. Tank vehicle and tank car loading or unloading facilities shall be separated from aboveground tanks, warehouses, other plant buildings or nearest line of adjoining property that may be built upon by a distance of 25 feet for Category 1 or 2 flammable liquids, or Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C), and 15 feet for Category 3 flammable liquids with a flashpoint at or above 100 °F (37.8 °C) and Category 4 flammable liquids measured from the nearest position of any fill spout. Buildings for pumps or shelters for personnel may be a part of the facility.

(ii) Category restriction. Equipment such as piping, pumps, and meters used for the transfer of Category 1 or 2 flammable liquids, or Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C), between storage tanks and the fill stem of the loading rack shall not be used for the transfer of Category 3 flammable liquids with a flashpoint at or above 100 °F (37.8 °C) or Category 4 flammable liquids.

* * * * *

(iv) * * *

(a) * * *

(1) Where Category 1 or 2 flammable liquids, or Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C), are loaded, or

(2) Where Category 3 flammable liquids with a flashpoint at or above 100 °F (37.8 °C) or Category 4 flammable liquids are loaded into vehicles which may contain vapors from previous cargoes of Category 1 or 2 flammable liquids, or Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C).

* * * * *

(d) * * *

(2) Where no Category 1 or 2 flammable liquids, or Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C), are handled at the loading facility and the tank vehicles loaded are used exclusively for Category 3 flammable liquids with a flashpoint at or above 100 °F (37.8 °C) and Category 4 flammable liquids; and

* * * * *

(v) Stray currents. Tank car loading facilities where Category 1 or 2 flammable liquids, or Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C) are loaded through open domes shall be protected against stray currents by bonding the pipe to at least one rail and to the rack structure if of metal. Multiple lines entering the rack area shall be electrically bonded together. In addition, in areas where excessive stray currents are known to exist, all pipe entering the rack area shall be provided with insulating sections to electrically isolate the rack piping from the pipelines. No bonding between the tank car and the rack or piping is required during either loading or unloading of Category 3 flammable liquids with a flashpoint at or above 100 °F (37.8 °C) or Category 4 flammable liquids.

(vi) Container filling facilities. Category 1 or 2 flammable liquids, or Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C), shall not be dispensed into containers unless the nozzle and container are electrically interconnected. Where the metallic floorplate on which the container stands while filling is electrically connected to the fill stem or where the fill stem is bonded to the container during filling operations by means of a bond wire, the provisions of this section shall be deemed to have been complied with.

(4) * * *

(viii) * * *

(e) In addition to the requirements of paragraph (f)(4)(viii)(d) of this section, each line conveying Category 1 or 2 flammable liquids, or Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C), leading to a wharf shall be provided with a readily accessible block valve located on shore near the approach to the wharf and outside of any diked area. Where more than one line is involved, the valves shall be grouped in one location.

* * * * *

(5) * * *

(i) Application. This paragraph (f)(5)(i) shall apply to areas where Category 1 or 2 flammable liquids, or Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C), are stored or handled. For areas where Category 3 flammable liquids with a flashpoint at or above 100 °F (37.8 °C) or Category 4 flammable liquids only are stored or handled, the electrical equipment may be installed in accordance with the provisions of Subpart S of this part, for ordinary locations.

* * * * *

(6) Sources of ignition. Category 1 or 2 flammable liquids, or Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C), shall not be handled, drawn, or dispensed where flammable vapors may reach a source of ignition. Smoking shall be prohibited except in designated localities. “No Smoking” signs shall be conspicuously posted where hazard from flammable liquid vapors is normally present.

* * * * *

(8) Fire control. Suitable fire-control devices, such as small hose or portable fire extinguishers, shall be available to locations where fires are likely to occur. Additional fire-control equipment may be required where a tank of more than 50,000 gallons individual capacity contains Category 1 or 2 flammable liquids, or Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C), and where an unusual exposure hazard exists from surrounding property. Such additional fire-control equipment shall be sufficient to extinguish a fire in the largest tank. The design and amount of such equipment shall be in accordance with approved engineering standards.

* * * * *

(g) * * *

(1) * * *

(i) * * *

(c) Apparatus dispensing Category 1 or 2 flammable liquids, or Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C), into the fuel tanks of motor vehicles of the public shall not be located at a bulk plant unless separated by a fence or similar barrier from the area in which bulk operations are conducted.

* * * * *

(e) The provisions of paragraph (g)(1)(i)(a) of this section shall not prohibit the dispensing of flammable liquids with a flashpoint below 100 °F (37.8 °C) in the open from a tank vehicle to a motor vehicle. Such dispensing shall be permitted provided:

* * * * *

(f) Category 1 or 2 flammable liquids, or Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C), shall not be stored or handled within a building having a basement or pit into which flammable vapors may travel, unless such area is provided with ventilation designed to prevent the accumulation of flammable vapors therein.

* * * * *

(iii) * * *

(a) Except where stored in tanks as provided in paragraph (g)(1)(ii) of this section, no Category 1 or 2 flammable liquids, or Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C), shall be stored within any service station building except in closed containers of aggregate capacity not exceeding 60 gallons. One container not exceeding 60 gallons capacity equipped with an approved pump is permitted.

(b) Category 1 or 2 flammable liquids, or Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C), may be transferred from one container to another in lubrication or service rooms of a service station building provided the electrical installation complies with Table H-19 and provided that any heating equipment complies with paragraph (g)(6) of this section.

(c) Category 3 flammable liquids with a flashpoint at or above 100 °F (37.8 °C) and Category 4 flammable liquids may be stored and dispensed inside service station buildings from tanks of not more than 120 gallons capacity each.

* * * * *

(v) Dispensing into portable containers. No delivery of any Category 1 or 2 flammable liquids, or Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C), shall be made into portable containers unless the container is constructed of metal, has a tight closure with screwed or spring cover, and is fitted with a spout or so designed so the contents can be poured without spilling.

* * * * *

(3) * * *

(iv) * * *

(a) Category 1 or 2 flammable liquids, or Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C), shall be transferred from tanks by means of fixed pumps so designed and equipped as to allow control of the flow and to prevent leakage or accidental discharge.

(b)(1) Only listed devices may be used for dispensing Category 1 or 2 flammable liquids, or Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C). No such device may be used if it shows evidence of having been dismantled.

(2) Every dispensing device for Category 1 or 2 flammable liquids, or Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C), installed after December 31, 1978, shall contain evidence of listing so placed that any attempt to dismantle the device will result in damage to such evidence, visible without disassembly or dismounting of the nozzle.

(c) Category 1 or 2 flammable liquids, or Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C), shall not be dispensed by pressure from drums, barrels, and similar containers. Approved pumps taking suction through the top of the container or approved self-closing faucets shall be used.

* * * * *

(v) * * *

(a) This paragraph (g)(3)(v) shall apply to systems for dispensing Category 1 or 2 flammable liquids, or Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C), where such liquids are transferred from storage to individual or multiple dispensing units by pumps located elsewhere than at the dispensing units.

* * * * *

(vi) * * *

(a) A listed manual or automatic-closing type hose nozzle valve shall be provided on dispensers used for the dispensing of Category 1 or 2 flammable liquids, or Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C).

* * * * *

(4) * * *

(iii) * * *

(a) * * *

* * * * *

(d) Piping handling Category 1 or 2 flammable liquids, or Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C), shall be grounded to control stray currents.

(5) * * *

(i) Application. This paragraph (g)(5) shall apply to areas where Category 1 or 2 flammable liquids, or Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C), are stored or handled. For areas where Category 3 flammable liquids with a flashpoint at or above 100 °F (37.8 °C) or Category 4 flammable liquids are stored or handled the electrical equipment may be installed in accordance with the provisions of subpart S of this part, for ordinary locations.

* * * * *

(6) * * *

(iv) Work areas. Heating equipment using gas or oil fuel may be installed in the lubrication, sales, or service room where there is no dispensing or transferring of Cagetory 1 or 2 flammable liquids or Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C), provided the bottom of the combustion chamber is at least 18 inches above the floor and the heating equipment is protected from physical damage by vehicles. Heating equipment using gas or oil fuel listed for use in garages may be installed in the lubrication or service room where Category 1 or 2 flammable liquids, or Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C), are dispensed provided the equipment is installed at least 8 feet above the floor.

* * * * *

(7) Drainage and waste disposal. Provision shall be made in the area where Category 1 or 2 flammable liquids, or Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C), are dispensed to prevent spilled liquids from flowing into the interior of service station buildings. Such provision may be by grading driveways, raising door sills, or other equally effective means. Crankcase drainings and flammable liquids shall not be dumped into sewers but shall be stored in tanks or drums outside of any building until removed from the premises.

* * * * *

(h) * * *

(3) * * *

(i) * * *

(a) Processing buildings shall be of fire-resistance or noncombustible construction, except heavy timber construction with load-bearing walls may be permitted for plants utilizing only stable Category 3 flammable liquids with a flashpoint at or above 100 °F (37.8 °C) or Category 4 flammable liquids. Except as provided in paragraph (h)(2)(ii) of this section or in the case of explosion resistant walls used in conjunction with explosion relieving facilities, see paragraph (h)(3)(iv) of this section, load-bearing walls are prohibited. Buildings shall be without basements or covered pits.

* * * * *

(iii) * * *

(b) Equipment used in a building and the ventilation of the building shall be designed so as to limit flammable vapor-air mixtures under normal operating conditions to the interior of equipment, and to not more than 5 feet from equipment which exposes Category 1 or 2 flammable liquids, or Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C), to the air. Examples of such equipment are dispensing stations, open centrifuges, plate and frame filters, open vacuum filters, and surfaces of open equipment.

(iv) Explosion relief. Areas where Category 1 or unstable liquids are processed shall have explosion venting through one or more of the following methods:

* * * * *

(5) Tank vehicle and tank car loading and unloading. Tank vehicle and tank car loading or unloading facilities shall be separated from aboveground tanks, warehouses, other plant buildings, or nearest line of adjoining property which may be built upon by a distance of 25 feet for Category 1 or 2 flammable liquids, or Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C), and 15 feet for Category 3 flammable liquids with a flashpoint at or above 100 °F (37.8 °C) and Category 4 flammable liquids measured from the nearest position of any fill stem. Buildings for pumps or shelters for personnel may be a part of the facility. Operations of the facility shall comply with the appropriate portions of paragraph (f)(3) of this section.

* * * * *

(7) * * *

(i) * * *

(b) Category 1 or 2 flammable liquids, or Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C), shall not be dispensed into containers unless the nozzle and container are electrically interconnected. Where the metallic floorplate on which the container stands while filling is electrically connected to the fill stem or where the fill stem is bonded to the container during filling operations by means of a bond wire, the provisions of this section shall be deemed to have been complied with.

* * * * *

(iii) * * *

(c) Locations where flammable vapor-air mixtures may exist under abnormal conditions and for a distance beyond Division 1 locations shall be classified Division 2 according to the requirements of subpart S of this part. These locations include an area within 20 feet horizontally, 3 feet vertically beyond a Division 1 area, and up to 3 feet above floor or grade level within 25 feet, if indoors, or 10 feet if outdoors, from any pump, bleeder, withdrawal fitting, meter, or similar device handling Category 1 or 2 flammable liquids, or Category 3 flammable liquids with a flashpoint below 100 °F (37.8 °C). Pits provided with adequate mechanical ventilation within a Division 1 or 2 area shall be classified Division 2. If Category 3 flammable liquids with a flashpoint at or above 100 °F (37.8 °C) or Category 4 flammable liquids only are handled, then ordinary electrical equipment is satisfactory though care shall be used in locating electrical apparatus to prevent hot metal from falling into open equipment.

* * * * *

(j) Scope. This section applies to the handling, storage, and use of flammable liquids with a flashpoint below 199.4 °F (93 °C) unless otherwise noted. This section does not apply to:

* * * * *

Table H-12—Maximum Allowable Size of Containers and Portable Tanks for Flammable Liquids Back to Top
Container type Category 1 Category 2 Category 3 Category 4
Note: Container exemptions: [a] Medicines, beverages, foodstuffs, cosmetics, and other common consumer items, when packaged according to commonly accepted practices, shall be exempt from the requirements of 1910.106(d)(2)(i) and (ii).
Glass or approved plastic 1 pt 1 qt 1 gal 1 gal.
Metal (other than DOT drums) 1 gal 5 gal 5 gal 5 gal.
Safety cans 2 gal 5 gal 5 gal 5 gal.
Metal drums (DOT specifications) 60 gal 60 gal 60 gal 60 gal.
Approved portable tanks 660 gal 660 gal 660 gal 660 gal.

BILLING CODE 4510-26-P

BILLING CODE 4510-26-C

* * * * *

5. Amend § 1910.107 as follows:

A. Amend paragraphs (c)(9)(i), (e)(1), (e)(2), (e)(3), (e)(6)(iv), (e)(8), and (e)(9) by removing the terms “flammable or combustible liquids” and replacing them with the phrase “flammable liquids or liquids with a flashpoint greater than 199.4 °F (93 °C)” and;

B. Revise paragraphs (e) introductory text and (e)(4) to read as follows:

§ 1910.107 Spray finishing using flammable and combustible materials.

* * * * *

(e) Flammable liquids and liquids with a flashpoint greater than 199.4 °F (93 °C)

* * * * *

(4) Transferring liquids. Except as provided in paragraph (e)(5) of this section the withdrawal of flammable liquids and liquids with a flashpoint greater than 199.4 °F (93 °C) from containers having a capacity of greater than 60 gallons shall be by approved pumps. The withdrawal of flammable liquids or liquids with a flashpoint greater than 199.4 °F (93 °C) from containers and the filling of containers, including portable mixing tanks, shall be done only in a suitable mixing room or in a spraying area when the ventilating system is in operation. Adequate precautions shall be taken to protect against liquid spillage and sources of ignition.

* * * * *

6. Amend § 1910.119 to revise paragraphs (a)(1)(ii) introductory text, (a)(1)(ii)(B) and the definition of “Trade secret” in paragraph (b) to read as follows:

§ 1910.119 Process safety management of highly hazardous chemicals.

* * * * *

(a) * * *

(1) * * *

(ii) A process which involves a Category 1 flammable gas (as defined in 1910.1200 (c)) or a flammable liquid with a flashpoint below 100 °F (37.8 °C) on site in one location, in a quantity of 10,000 pounds (4535.9 kg) or more except for:

* * * * *

(B) Flammable liquids with a flashpoint below 100 °F (37.8 °C) stored in atmospheric tanks or transferred which are kept below their normal boiling point without benefit of chilling or refrigeration.

* * * * *

(b) Definitions.* * *

Trade secret means any confidential formula, pattern, process, device, information or compilation of information that is used in an employer's business, and that gives the employer an opportunity to obtain an advantage over competitors who do not know or use it. See Appendix E to § 1910.1200—Definition of a Trade Secret (which sets out the criteria to be used in evaluating trade secrets).

* * * * *

7. In § 1910.120, revise the definition of the term Health hazard in paragraph (a)(3) to read as follows:

§ 1910.120 Hazardous waste operations and emergency response.

(a) * * *

(3) * * *

Health hazard means a chemical or a pathogen where acute or chronic health effects may occur in exposed employees. It also includes stress due to temperature extremes. The term “health hazard” includes chemicals which are classified in accordance with the Hazard Communication Standard, 29 CFR 1910.1200 as posing one of the following effects: acute toxicity (any route of exposure); skin corrosion or irritation; serious eye damage or eye irritation; respiratory or skin sensitization; germ cell mutagenicity; carcinogenicity; reproductive toxicity; target organ specific systemic toxicity (single or repeated dose); or aspiration toxicity. See Appendix A to § 1910.1200—Health Hazard Criteria (Mandatory) (for the criteria for determining whether a chemical is classified as a health hazard).

* * * * *

8. Amend paragraph (d) of § 1910.123, by removing the term “Combustible liquid” and revising the definitions of the terms “Flammable liquid” and “Flashpoint” to read as follows:

§ 1910.123 Dipping and coating operations: Coverage and definitions.

* * * * *

(d) * * *

Flammable liquid means a liquid having a flashpoint below 199.4 °F. (93 °C.).

Flashpoint means the minimum temperature at which a liquid gives off a vapor in sufficient concentration to ignite if tested in accordance with the test methods in Appendix B to § 1910.1200—Physical Hazard Criteria.

* * * * *

9. In § 1910.124, revise paragraph (c)(2) introductory text to read as follows:

§ 1910.124 General requirements for dipping and coating operations.

* * * * *

(c) * * *

(2) You must ensure that any exhaust air re-circulated from a dipping or coating operation using flammable liquids or liquids with a flashpoint greater than 199.4 °F (93 °C) is:

* * * * *

10. Amend § 1910.125 introductory text (including the table) to read as follows:

§ 1910.125 Additional requirements for dipping and coating operations that use flammable or combustible liquids.

If you use flammable liquids, you must comply with the requirements of this section as well as the requirements of §§ 1910.123, 1910.124, and 1910.126, as applicable.

You must comply with this section if: And:
The flashpoint of the liquid is 199.4 °F (93 °C) or above The liquid is heated as part of the operation; or a heated object is placed in the liquid.

* * * * *

Subpart Q—[Amended] Back to Top

11. Continue the authority citation for subpart Q to read as follows:

Authority:

Sections 4, 6, and 8 of the Occupational Safety and Health Act of 1970 (29 U.S.C. 653, 655, and 657); Secretary of Labor's Orders Nos. 12-71 (36 FR 8754), 8-76 (41 FR 25059), 9-83 (48 FR 35736), 1-90 (55 FR 9033), 6-96 (62 FR 111), 3-2000 (65 FR 50017), 5-2002 (67 FR 65008), or 5-2007 (72 FR 31159), as applicable; and 29 CFR part 1911.

12. Amend § 1910.252 as follows;

A. Revise paragraph (c)(1)(iv);

B. Add new paragraph (c)(1)(v).

§ 1910.252 General requirements.

* * * * *

(c) * * *

(1) * * *

(iv) Hazard communication. The employer shall include the potentially hazardous materials employed in fluxes, coatings, coverings, and filler metals, all of which are potentially used in welding and cutting, or are released to the atmosphere during welding and cutting, in the program established to comply with the Hazard Communication Standard (HCS) (29 CFR 1910.1200). The employer shall ensure that each employee has access to labels on containers of such materials and safety data sheets, and is trained in accordance with the provisions of 29 CFR 1910.1200. Potentially hazardous materials shall include but not be limited to the materials itemized in paragraphs (c)(5) through (c)(12) of this section.

(v) Additional considerations for hazard communication in welding, cutting, and brazing.

(A) The suppliers shall determine the hazard as required by § 1910.1200, if any, associated with the use of their materials in welding, cutting, and brazing.

(B) All filler metals and fusible granular materials shall carry the following notice, as a minimum, on tags, boxes, or other containers:

Do not use in areas without adequate ventilation

See ANSI Z49.1-1967 Safety in Welding, Cutting, and Allied Processes published by the American Welding Society.

(C) Where brazing (welding) filler metals contain cadmium in significant amounts, the labels shall indicate the hazards associated with cadmium including cancer, lung and kidney effects, and acute toxicity effects.

(D) Where brazing and gas welding fluxes containing fluorine compounds, the labels shall indicate the hazards associated with fluorine compounds including eye and respiratory tract effects.

* * * * *

Subpart Z—[Amended] Back to Top

13. Revise the authority citation for subpart Z to read as follows:

Authority:

Secs. 4, 6, 8, of the Occupational Safety and Health Act of 1970 (29 U.S.C. 653, 655, 657); Secretary of Labor's Order No. 12-71 (36 FR 8754), 8-76 (41 FR 25059), 9-83 (48 FR 35736), 1-90 (55 FR 9033), 6-96 (62 FR 111), 3-2000 (65 FR 50017), 5-2002 (67 FR 65008), or 5-2007 (72 FR 31159), as applicable; and 29 CFR part 1911.

All of subpart Z issued under section 6(b) of the Occupational Safety and Health Act of 1970, except those substances that have exposure limits listed in Tables Z-1, Z-2, and Z-3 of 29 CFR 1910.1000. The latter were issued under section 6(a) (29 U.S.C. 655(a)).

Section 1910.1000, Tables Z-1, Z-2 and Z-3 also issued under 5 U.S.C. 553, Section 1910.1000 Tables Z-1, Z-2, and Z-3 but not under 29 CFR part 1911 except for the arsenic (organic compounds), benzene, cotton dust, and chromium (VI) listings.

Section 1910.1001 also issued under section 107 of the Contract Work Hours and Safety Standards Act (40 U.S.C. 3704) and 5 U.S.C. 553.

Section 1910.1002 also issued under 5 U.S.C. 553, but not under 29 U.S.C. 655 or 29 CFR part 1911.

Sections 1910.1018, 1910.1029, and 1910.1200 also issued under 29 U.S.C. 653.

Section 1910.1030 also issued under Pub. L. 106-430, 114 Stat. 1901.

14. Amend § 1910.1001 as follows:

A. Remove paragraph (j)(5);

B. Redesignate paragraphs (j)(1) through (j)(4) as paragraphs (j)(2) through (j)(5);

C. Revise paragraphs (h)(2)(iv), (h)(3)(vi), the newly redesignated paragraphs (j)(4), (j)(5), and the introductory text of (j)(6).

D. Add new paragraph (j)(1);

The revisions, with new designations, read as follows:

§ 1910.1001 Asbestos.

* * * * *

(h) * * *

(2) * * *

(iv) The employer shall ensure that containers of contaminated protective devices or work clothing, which are to be taken out of change rooms or the workplace for cleaning, maintenance or disposal, bear labels in accordance with paragraph (j) of this section.

(3) * * *

(vi) The employer shall ensure that contaminated clothing is transported in sealed impermeable bags, or other closed, impermeable containers, and labeled in accordance with paragraph (j) of this section.

* * * * *

(j) * * *

(1) Hazard Communication—General. The employer shall include asbestos in the program established to comply with the Hazard Communication Standard (HCS) (29 CFR 1910.1200). The employer shall ensure that each employee has access to labels on containers of asbestos and to safety data sheets, and is trained in accordance with the provisions of HCS and paragraph (j)(7) of this section. The employer shall ensure that at least the following hazards are addressed: Cancer and lung effects.

* * * * *

(4) Warning signs.

(i) Posting. Warning signs shall be provided and displayed at each regulated area. In addition, warning signs shall be posted at all approaches to regulated areas so that an employee may read the signs and take necessary protective steps before entering the area.

(ii) Sign specifications.

(A) The warning signs required by paragraph (j)(4)(i) of this section shall bear the following legend:

DANGER

ASBESTOS

MAY CAUSE CANCER

CAUSES DAMAGE TO LUNGS

AUTHORIZED PERSONNEL ONLY

(B) In addition, where the use of respirators and protective clothing is required in the regulated area under this section, the warning signs shall include the following:

WEAR RESPIRATORY PROTECTION AND PROTECTIVE CLOTHING IN THIS AREA

(iii) The employer shall ensure that employees working in and contiguous to regulated areas comprehend the warning signs required to be posted by paragraph (j)(4)(i) of this section. Means to ensure employee comprehension may include the use of foreign languages, pictographs and graphics.

(iv) At the entrance to mechanical rooms/areas in which employees reasonably can be expected to enter and which contain ACM and/or PACM, the building owner shall post signs which identify the material which is present, its location, and appropriate work practices which, if followed, will ensure that ACM and/or PACM will not be disturbed. The employer shall ensure, to the extent feasible, that employees who come in contact with these signs can comprehend them. Means to ensure employee comprehension may include the use of foreign languages, pictographs, graphics, and awareness training.

(5) Warning labels.

(i) Labeling. Labels shall be affixed to all raw materials, mixtures, scrap, waste, debris, and other products containing asbestos fibers, or to their containers. When a building owner or employer identifies previously installed ACM and/or PACM, labels or signs shall be affixed or posted so that employees will be notified of what materials contain ACM and/or PACM. The employer shall attach such labels in areas where they will clearly be noticed by employees who are likely to be exposed, such as at the entrance to mechanical room/areas. Signs required by paragraph (j) of this section may be posted in lieu of labels so long as they contain information required for labeling.

(ii) Label specifications. In addition to the requirements of paragraph (j)(1), the employer shall ensure that labels of bags or containers of protective clothing and equipment, scrap, waste, and debris containing asbestos fibers include the following information:

DANGER

CONTAINS ASBESTOS FIBERS

MAY CAUSE CANCER

CAUSES DAMAGE TO LUNGS

DO NOT BREATHE DUST

(6) The provisions for labels and for safety data sheets required by paragraph (j) of this section do not apply where:

* * * * *

15. Amend § 1910.1003 as follows:

A. Amend the last sentence in paragraph (c)(4)(v) to remove the words “paragraphs (e)(2), (3), and (4)” and add the words “paragraph (e)” in their place;

B. Revise the heading of paragraph (e);

C. Revise paragraphs (e)(1) and (e)(2)

D. Remove paragraph (e)(3);

E. Redesignate paragraphs (e)(4) and (e)(5) as (e)(3) and (e)(4).

The revisions read as follows:

§ 1910.1003 13 Carcinogens (4-nitrobiphenyl, etc.).

* * * * *

(e) Communication of hazards. (1) Hazard communication. The employer shall include the carcinogens listed below in the program established to comply with the Hazard Communication Standard (HCS) (29 CFR 1910.1200). The employer shall ensure that each employee has access to labels on containers of the carcinogens listed below and to safety data sheets, and is trained in accordance with the provisions of HCS and paragraph (e)(3) of this section. The employer shall ensure that at least the hazards listed for the following chemicals are addressed:

4-Nitrobiphenyl: Cancer;

alpha-Naphthylamine: Cancer: skin irritation, and acute toxicity effects;

Methyl chloromethyl ether: Cancer; skin, eye and respiratory effects; acute toxicity effects; and flammability;

3,3'-Dichlorobenzidine (and its salts): Cancer and skin sensitization;

Bis-Chloromethyl ether: Cancer; skin, eye, and respiratory tract effects; acute toxicity effects; and flammability;

Beta-Naphthylamine: Cancer and acute toxicity effects;

Benzidine: Cancer and acute toxicity effects;

4-Aminodiphenyl: Cancer

Ethyleneimine: Cancer; mutagenicity; skin and eye effects; liver effects; kidney effects; acute toxicity effects; and flammability;

Beta-Propiolactone: Cancer; skin irritation; eye effects; and acute toxicity effects;

2-Acetylaminofluorene: Cancer;

4-Dimethylaminoazo-benzene: Cancer; skin effects; and respiratory tract irritation;

N-Nitrosodimethylamine: Cancer; liver effects; and acute toxicity effects;

(2) Signs. (i) The employer shall post entrances to regulated areas with signs bearing the legend:

DANGER

(CHEMICAL IDENTIFICATION)

MAY CAUSE CANCER

AUTHORIZED PERSONNEL ONLY

(ii) The employer shall post signs at entrances to regulated areas containing operations covered in paragraph (c)(5) of this section. The signs shall bear the legend:

DANGER

(CHEMICAL IDENTIFICATION)

MAY CAUSE CANCER

WEAR AIR SUPPLIED HOODS, IMPERVIOUS SUITS, AND PROTECTIVE EQUIPMENT IN THIS AREA

AUTHORIZED PERSONNEL ONLY

(iii) Appropriate signs and instructions shall be posted at the entrance to, and exit from, regulated areas, informing employees of the procedures that must be followed in entering and leaving a regulated area.

* * * * *

16. Amend § 1910.1017 by revising paragraph (l) to read as follows:

§ 1910.1017 Vinyl chloride.

* * * * *

(l) Communication of hazards. (1) Hazard communication. The employer shall include vinyl chloride in the program established to comply with the Hazard Communication Standard (HCS) (29 CFR 1910.1200). The employer shall ensure that each employee has access to labels on containers of vinyl chloride and to safety data sheets, and is trained in accordance with the provisions of HCS and paragraph (j) of this section. The employer shall ensure that at least the following hazards are addressed: Cancer; central nervous system effects; liver effects; blood effects; and flammability.

(2) Signs. (i) The employer shall post entrances to regulated areas with legible signs bearing the legend:

DANGER

VINYL CHLORIDE

MAY CAUSE CANCER

AUTHORIZED PERSONNEL ONLY

(ii) The employer shall post signs at areas containing hazardous operations or where emergencies currently exist. The signs shall be legible and bear the legend:

DANGER

VINYL CHLORIDE

MAY CAUSE CANCER

WEAR RESPIRATORY PROTECTION AND PROTECTIVE CLOTHING IN THIS AREA

AUTHORIZED PERSONNEL ONLY

(3) Labels. (i) In addition to the other requirements in this paragraph (l), the employer shall ensure that labels for containers of polyvinyl chloride resin waste from reactors or other waste contaminated with vinyl chloride are legible and include the following information:

CONTAMINATED WITH VINYL CHLORIDE

MAY CAUSE CANCER

(4) No statement shall appear on or near any required sign, label, or instruction which contradicts or detracts from the effect of any required warning, information, or instruction.

* * * * *

17. Amend § 1910.1018 by revising paragraphs (j)(2)(vii) and (p) as follows:

§ 1910.1018 Inorganic arsenic.

* * * * *

(j) * * *

(2) * * *

(vii) In addition to the communication requirements in paragraph (p) of this section, the employer shall ensure that the containers of contaminated protective clothing and equipment in the workplace or which are to be removed from the workplace are labeled and that the labels include the following information: DANGER: CONTAMINATED WITH INORGANIC ARSENIC. MAY CAUSE CANCER. DO NOT EAT, DRINK, OR SMOKE. DO NOT REMOVE DUST BY BLOWING OR SHAKING.

* * * * *

(p) Communication of hazards. (1) Hazard communication. (i) The employer shall include inorganic arsenic in the program established to comply with the Hazard Communication Standard (HCS) (29 CFR 1910.1200). The employer shall ensure that each employee has access to labels on containers of inorganic arsenic and to safety data sheets, and is trained in accordance with the provisions of HCS and paragraph (o) of this section. The employer shall ensure that at least the following hazards are addressed: Cancer; liver effects; skin effects; respiratory irritation; nervous system effects; and acute toxicity effects.

(ii) The employer shall ensure that no statement appears on or near any sign or label required by this paragraph which contradicts or detracts from the meaning of the required sign or label.

(2) Signs. (i) The employer shall post signs demarcating regulated areas bearing the legend:

DANGER

INORGANIC ARSENIC

MAY CAUSE CANCER

DO NOT EAT, DRINK OR SMOKE

WEAR RESPIRATORY PROTECTION IN THIS AREA

AUTHORIZED PERSONNEL ONLY

(ii) The employer shall ensure that signs required by this paragraph are illuminated and cleaned as necessary so that the legend is readily visible.

* * * * *

18. Amend § 1910.1025 to revise paragraph (g)(2)(vii) and paragraph (m) to read as follows:

§ 1910.1025 Lead.

* * * * *

(g) * * *

(2) * * *

(vii) The employer shall ensure that labels of bags or containers of contaminated protective clothing and equipment include the following information: DANGER: COTHING AND EQUIPMENT CONTAMINATED WITH LEAD. MAY DAMAGE FERTILITY OR THE UNBORN CHILD. CAUSES DAMAGE TO THE CENTRAL NERVOUS SYSTEM. DO NOT EAT, DRINK OR SMOKE WHEN HANDLING. DO NOT REMOVE DUST BY BLOWING OR SHAKING

* * * * *

(m) Communication of hazards. (1) Hazard communication. The employer shall include lead in the program established to comply with the Hazard Communication Standard (HCS) (29 CFR 1910.1200). The employer shall ensure that each employee has access to labels on containers of lead and to safety data sheets, and is trained in accordance with the provisions of HCS and paragraph (l) of this section. The employer shall ensure that at least the following hazards are addressed: Reproductive/developmental toxicity; central nervous system effects; kidney effects; blood effects; and acute toxicity effects.

(2) Signs. (i) The employer shall post the following warning signs in each work area where the PEL is exceeded:

DANGER

LEAD

MAY DAMAGE FERTILITY OR THE UNBORN CHILD

CAUSES DAMAGE TO THE CENTRAL NERVOUS SYSTEM

DO NOT EAT, DRINK OR SMOKE IN THIS AREA

(ii) The employer shall ensure that no statement appears on or near any sign required by this paragraph which contradicts or detracts from the meaning of the required sign.

(iii) The employer shall ensure that signs required by this paragraph are illuminated and cleaned as necessary so that the legend is readily visible.

* * * * *

19. Amend § 1910.1026 to revise paragraphs (h)(2)(iv), (j)(3)(ii) and (l)(1) to read as follows:

§ 1910.1026 Chromium (VI).

* * * * *

(h) * * *

(2) * * *

(iv) The employer shall ensure that bags or containers of contaminated protective clothing or equipment that are removed from change rooms for laundering, cleaning, maintenance, or disposal are labeled in accordance with the requirements of the Hazard Communication standard, 29 CFR 1910.1200.

* * * * *

(j) * * *

(3) * * *

(ii) The employer shall ensure that bags or containers of waste, scrap, debris, and any other materials contaminated with chromium (VI) that are consigned for disposal are labeled in accordance with the Hazard Communication Standard, 29 CFR 1910.1200.

* * * * *

(l) * * *

(1) Hazard communication. The employer shall include chromium (VI) in the program established to comply with the Hazard Communication Standard (HCS) (29 CFR 1910.1200). The employer shall ensure that each employee has access to labels on containers of chromium (VI) and to safety data sheets, and is trained in accordance with the provisions of HCS and paragraph (l)(2) of this section. The employer shall ensure that at least the following hazards are addressed: Cancer, eye irritation, and skin sensitization.

* * * * *

20. Amend § 1910.1027 to revise paragraphs (i)(2)(iv), (k)(7), (m)(1), (m)(2)(ii), (m)(3)(i), and (m)(3)(ii) to read as follows:

§ 1910.1027 Cadmium.

* * * * *

(i) * * *

(2) * * *

(iv) The employer shall ensure that bags or containers of contaminated protective clothing and equipment that are to be taken out of the change rooms or the workplace for laundering, cleaning, maintenance or disposal are labeled in accordance with paragraph (m) of this section. As a minimum, the employer shall ensure that labels on containers of contaminated protective clothing and equipment include the following information:

DANGER

CONTAINS CADMIUM

MAY CAUSE CANCER

CAUSES DAMAGE TO LUNGS AND KIDNEYS

AVOID CREATING DUST

* * * * *

(k) * * *

(7) Waste, scrap, debris, bags, containers, personal protective equipment, and clothing contaminated with cadmium and consigned for disposal shall be collected and disposed of in sealed impermeable bags or other closed, impermeable containers. These bags and containers shall be labeled in accordance with paragraph (m) of this section.

* * * * *

(m) * * *

(1) Hazard communication. The employer shall include cadmium in the program established to comply with the Hazard Communication Standard (HCS) (29 CFR 1910.1200). The employer shall ensure that each employee has access to labels on containers of cadmium and to safety data sheets, and is trained in accordance with the provisions of HCS and paragraph (m)(4) of this section. The employer shall ensure that at least the following hazards are addressed: Cancer; lung effects; kidney effects; and acute toxicity effects.

(2) * * *

(ii) Warning signs required by paragraph (m)(2)(i) of this section shall bear the following legend:

DANGER

CADMIUM

MAY CAUSE CANCER

CAUSES DAMAGE TO LUNGS AND KIDNEYS

WEAR RESPIRATORY PROTECTION IN THIS AREA

AUTHORIZED PERSONNEL ONLY

(3) * * *

(i) Shipping and storage containers containing cadmium or cadmium compounds shall bear appropriate warning labels, as specified in paragraph (m)(1) of this section.

(ii) The warning labels for waste, scrap, or debris shall include at least the following information:

DANGER

CONTAINS CADMIUM

MAY CAUSE CANCER

* * * * *

21. Amend § 1910.1028 to revise the heading of paragraph (j) and the regulatory text of paragraphs (j)(1) and (j)(2) to read as follows:

§ 1910.1028 Benzene.

* * * * *

(j) Communication of hazards. (1) Hazard communication. The employer shall include benzene in the program established to comply with the Hazard Communication Standard (HCS) (29 CFR 1910.1200). The employer shall ensure that each employee has access to labels on containers of benzene and to safety data sheets, and is trained in accordance with the provisions of HCS and (j)(3) of this section. The employer shall ensure that at least the following hazards are addressed: Cancer; central nervous system effects; blood effects; aspiration; skin, eye, and respiratory tract irritation; and flammability.

Note to paragraph (j)(1) of this section: There is no requirement to label pipes.

(2) Signs. The employer shall post signs at entrances to regulated areas. The signs shall bear the following legend:

DANGER

BENZENE

MAY CAUSE CANCER

HIGHLY FLAMMABLE LIQUID AND VAPOR

DO NOT SMOKE

WEAR RESPIRATORY PROTECTION IN THIS AREA

AUTHORIZED PERSONNEL ONLY

* * * * *

22. Amend § 1910.1029 to revise paragraph (l) to read as follows:

§ 1910.1029 Coke oven emissions.

* * * * *

(l) Communication of hazards. (1) Hazard communication. The employer shall include coke oven emissions in the program established to comply with the Hazard Communication Standard (HCS) (29 CFR 1910.1200). The employer shall ensure that each employee has access to labels on containers of chemicals and substances associated with coke oven processes and to safety data sheets, and is trained in accordance with the provisions of HCS and paragraph (k) of this section. The employer shall ensure that at least the following hazard is addressed: Cancer.

(2) Signs.

(i) The employer shall post signs in the regulated area bearing the legend:

DANGER

COKE OVEN EMISSIONS

MAY CAUSE CANCER

DO NOT EAT, DRINK OR SMOKE

WEAR RESPIRATORY PROTECTION IN THIS AREA

AUTHORIZED PERSONNEL ONLY

(ii) In addition, the employer shall post signs in the areas where the permissible exposure limit is exceeded bearing the legend:

WEAR RESPIRATORY PROTECTION IN THIS AREA

(iii) The employer shall ensure that no statement appears on or near any sign required by this paragraph which contradicts or detracts from the effects of the required sign.

(iv) The employer shall ensure that signs required by this paragraph are illuminated and cleaned as necessary so that the legend is readily visible.

(3) Labels. In addition to the requirements in (l)(1) of this paragraph, the employer shall ensure that labels of containers of contaminated protective clothing and equipment include the following information:

CONTAMINATED WITH COKE EMISSIONS

MAY CAUSE CANCER

DO NOT EAT, DRINK, OR SMOKE

DO NOT REMOVE DUST BY BLOWING OR SHAKING

* * * * *

23. Amend § 1910.1043 to revise paragraph (j) as follows:

§ 1910.1043 Cotton dust.

* * * * *

(j) Signs. The employer shall post the following warning sign in each work area where the permissible exposure limit for cotton dust is exceeded:

DANGER

COTTON DUST

CAUSES DAMAGE TO LUNGS

(BYSSINOSIS)

WEAR RESPIRATORY PROTECTION IN THIS AREA

* * * * *

24. Amend § 1910.1044 to revise paragraphs (j)(2)(v), (k)(1)(iii)(b), and (o) to read as follows:

§ 1910.1044 1,2-dibromo-3-chloropropane.

* * * * *

(j) * * *

(2) * * *

(v) Containers of DBCP contaminated protective devices or work clothing which are to be taken out of change rooms or the workplace for cleaning, maintenance or disposal, shall bear labels in accordance with paragraph (o) of this section. As a minimum, the employer shall ensure that labels for containers of contaminated protective devices or work clothing include the following information: CONTAMINATED WITH 1,2-Dibromo-3-chloropropane (DBCP), MAY CAUSE CANCER.

* * * * *

(k) * * *

(1) * * *

(iii) * * *

(b) Portable vacuum units used to collect DBCP may not be used for other cleaning purposes and shall be labeled as prescribed by paragraph (o) of this section.

* * * * *

(o) Communication of hazards. (1) General. (i) Hazard communication. The employer shall include DBCP in the program established to comply with the Hazard Communication Standard (HCS) (29 CFR 1910.1200). The employer shall ensure that each employee has access to labels on containers of DBCP and to safety data sheets, and is trained in accordance with the provisions of HCS and paragraph (n) of this section. The employer shall ensure that at least the following hazards are addressed: Cancer; reproductive effects; liver effects; kidney effects; central nervous system effects; skin, eye and respiratory tract irritation; and acute toxicity effects.

(ii) The employer shall ensure that no statement appears on or near any sign or label required by this paragraph which contradicts or detracts from the meaning of the required sign or label.

(2) Signs.

The employer shall post signs to clearly indicate all regulated areas. These signs shall bear the legend:

DANGER

1,2-Dibromo-3-chloropropane

MAY CAUSE CANCER

WEAR RESPIRATORY PROTECTION IN THIS AREA

AUTHORIZED PERSONNEL ONLY

(3) The employer shall ensure that the precautionary labels required by this paragraph are readily visible and legible.

* * * * *

25. Amend § 1910.1045 to revise paragraphs (p)(1)(i), (p)(2)(i), and (p)(3) to read as follows:

§ 1910.1045 Acrylonitrile.

* * * * *

(p) Communication of hazards. (1) General. (i) Hazard communication. The employer shall include AN in the program established to comply with the Hazard Communication Standard (HCS) (29 CFR 1910.1200). The employer shall ensure that each employee has access to labels on containers of AN and to safety data sheets, and is trained in accordance with the provisions of HCS and paragraph (o) of this section. The employer shall ensure that at least the following hazards are addressed: Cancer; central nervous system effects; liver effects, skin sensitization, skin, respiratory, and eye irritation; acute toxicity effects; and flammability.

* * * * *

(2) Signs. (i) The employer shall post signs to clearly indicate all workplaces where AN concentrations exceed the permissible exposure limits. The signs shall bear the following legend:

DANGER

ACRYLONITRILE (AN)

MAY CAUSE CANCER

RESPIRATORY PROTECTION MAY BE REQURED IN THIS AREA

AUTHORIZED PERSONNEL ONLY

* * * * *

(3) Labels. The employer shall ensure that precautionary labels are affixed to all containers of liquid AN and AN-based materials not exempted under paragraph (a)(2) of this section. The employer shall ensure that the labels remain affixed when the materials are sold, distributed, or otherwise leave the employer's workplace.

* * * * *

26. Amend § 1910.1047 to revise the heading of paragraph (j) and paragraphs (j)(1) and (j)(2) to read as follows:

§ 1910.1047 Ethylene oxide.

* * * * *

(j) Communication of hazards. (1) Hazard communication. The employer shall include EtO in the program established to comply with the Hazard Communication Standard (HCS) (29 CFR 1910.1200). The employer shall ensure that each employee has access to labels on containers of EtO and to safety data sheets, and is trained in accordance with the provisions of HCS and paragraph (j)(3) of this section. The employer shall ensure that at least the following hazards are addressed: Cancer; reproductive effects; mutagenicity; central nervous system; skin sensitization; skin, eye and respiratory tract irritation; acute toxicity effects; and flammability.

(2) Signs and labels.

(i) Signs. The employer shall post and maintain legible signs demarcating regulated areas and entrances or access ways to regulated areas that bear the following legend:

DANGER

ETHYLENE OXIDE

MAY CAUSE CANCER

MAY DAMAGE FERTILITY OR THE UNBORN CHILD

RESPIRATORY PROTECTION AND PROTECTIVE CLOTHING MAY BE REQUIRED IN THIS AREA

AUTHORIZED PERSONNEL ONLY

(ii) Labels. The employer shall ensure that labels are affixed to all containers of EtO whose contents are capable of causing employee exposure at or above the action level or whose contents may reasonably be foreseen to cause employee exposure above the excursion limit, and that the labels remain affixed when the containers of EtO leave the workplace. For the purposes of this paragraph, reaction vessels, storage tanks, and pipes or piping systems are not considered to be containers.

Note to paragraph (j)(2):

The labeling requirements under this section do not apply where EtO is used as a pesticide, as such term is defined in the Federal Insecticide, Fungicide, and Rodenticide Act (7 U.S.C. 136 et seq.), when it is labeled pursuant to that Act and regulations issued under that Act by the Environmental Protection Agency.

* * * * *

27. Amend § 1910.1048 to revise paragraphs (e)(1); (h)(2)(ii); (j)(4) and (m) to read as follows:

§ 1910.1048 Formaldehyde.

* * * * *

(e) * * *

(1) The employer shall establish regulated areas where the concentration of airborne formaldehyde exceeds either the TWA or the STEL and post all entrances and access ways with signs bearing the following legend:

DANGER

FORMALDEHYDE

MAY CAUSE CANCER

CAUSES SKIN, EYE, AND RESPIRATORY IRRITATION

AUTHORIZED PERSONNEL ONLY

* * * * *

(h) * * *

(2) * * *

(ii) When formaldehyde-contaminated clothing and equipment is ventilated, the employer shall establish storage areas so that employee exposure is minimized.

(A) Signs. Storage areas for contaminated clothing and equipment shall have signs bearing the following legend:

DANGER

FORMALDEHYDE-CONTAMINATED [CLOTHING] EQUIPMENT

MAY CAUSE CANCER

CAUSES SKIN, EYE AND RESPIRATORY IRRITATION

DO NOT BREATHE VAPOR

DO NOT GET ON SKIN

(B) Labels. The employer shall ensure containers for contaminated clothing and equipment and storage areas are labeled in accordance with the Hazard Communication standard, 29 CFR 1910.1200, and shall, as a minimum, include the following:

DANGER

FORMALDEHYDE-CONTAMINATED [CLOTHING] EQUIPMENT

MAY CAUSE CANCER

CAUSES SKIN, EYE, AND RESPIRATORY IRRITATION

DO NOT BREATHE VAPOR

DO NOT GET ON SKIN

* * * * *

(j) * * *

(4) Formaldehyde-contaminated waste and debris resulting from leaks or spills shall be placed for disposal in sealed containers bearing a label warning of formaldehyde's presence and of the hazards associated with formaldehyde. The employer shall ensure that the labels are in accordance with paragraph (m) of this section.

* * * * *

(m) Communication of hazards. (1) Hazard communication. The employer shall include formaldehyde in the program established to comply with the Hazard Communication Standard (HCS) (29 CFR 1910.1200). The employer shall ensure that each employee has access to labels on containers of formaldehyde and to safety data sheets, and is trained in accordance with the provisions of HCS and paragraph (n) of this section. The employer shall ensure that at least the following hazards are addressed: Cancer; skin and respiratory sensitization; eye, skin and respiratory tract irritation; acute toxicity effects; and flammability.

(i) The employer must include chemicals and substances associated with formaldehyde gas, all mixtures or solutions composed of greater than 0.1 percent formaldehyde, and materials capable of releasing formaldehyde into the air at concentrations reaching or exceeding 0.1 ppm, in the hazard communication program.

(ii) In making the determinations of anticipated levels of formaldehyde release, the employer may rely on objective data indicating the extent of potential formaldehyde release under reasonably foreseeable conditions of use.

(2) In addition to the requirements in paragraphs (m)(1) introductory text and (m)(1)(i) of this section, for materials listed in paragraph (m)(1)(i) of this section capable of releasing formaldehyde at levels above 0.5 ppm, labels shall appropriately address all hazards as defined in paragraph (d) of § 1910.1200 and Appendices A and B to § 1910.1200, including cancer and respiratory sensitization, and shall contain the hazard statement “may cause cancer.”

* * * * *

28. Amend § 1910.1050 as follows:

A. Revise paragraph (i)(2)(v) and the heading of paragraph (k);

B. Revise paragraphs (k)(1) and (k)(2);

C. Redesignate paragraphs (k)(3) and (k)(4) as (k)(4) and (k)(5);

D. Add a new paragraph (k)(3).

The revisions and additions read as follows:

§ 1910.1050 Methylenedianiline.

* * * * *

(i) * * *

(2) * * *

(v) Containers of MDA-contaminated protective work clothing or equipment, which are to be taken out of change rooms or the workplace for cleaning, maintenance, or disposal, shall bear labels warning of the hazards of MDA. The employer shall ensure that labels are consistent with requirements in paragraph (k) of this section and that labels include at least the following information:

DANGER

CONTAINS METHYLENEDIANILINE (MDA)

MAY CAUSE CANCER

CAUSES DAMAGE TO THE LIVER

* * * * *

(k) Communication of hazards.

(1) Hazard communication. The employer shall include MDA in the program established to comply with the Hazard Communication Standard (HCS) (29 CFR 1910.1200). The employer shall ensure that each employee has access to labels on containers of MDA and to safety data sheets, and is trained in accordance with the provisions of HCS and paragraph (k)(4) of this section. The employer shall ensure that at least the following hazards are addressed: Cancer; liver effects; and skin sensitization.

(2) Signs. The employer shall post and maintain legible signs demarcating regulated areas and entrances or access ways to regulated areas that bear the following legend:

DANGER

MDA

MAY CAUSE CANCER

CAUSES DAMAGE TO THE LIVER

RESPIRATORY PROTECTION AND PROTECTIVE CLOTHING MAY BE REQUIRED IN THIS AREA

AUTHORIZED PERSONNEL ONLY

(3) Safety data sheets (SDS). In meeting the obligation to provide safety data sheets, employers shall make appropriate use of the information found in Appendices A and B to § 1910.1050 .

* * * * *

29. Amend § 1910.1051 to revise paragraph (l)(1) as follows:

§ 1910.1051 1,3-Butadiene.

* * * * *

(l) * * *

(1) Hazard communication. The employer shall include BD in the program established to comply with the Hazard Communication Standard (HCS) (29 CFR 1910.1200). The employer shall ensure that each employee has access to labels on containers of BD and to safety data sheets, and is trained in accordance with the provisions of HCS and paragraph (l)(2) of this section. The employer shall ensure that at least the following hazards are addressed: Cancer; eye and respiratory tract irritation; center nervous system effects; and flammability.

* * * * *

30. Amend § 1910.1052 to revise paragraph (k) as follows:

§ 1910.1052 Methylene chloride.

* * * * *

(k) Hazard communication. The employer shall include MC in the workplace hazard communication program established to comply with the Hazard Communication Standard (HCS) (29 CFR 1910.1200). The employer shall ensure that each employee has access to labels on containers of MC and to safety data sheets, and is trained in accordance with the provisions of HCS and paragraph (l) of this section. The employer shall provide information on at least the following hazards: Cancer, cardiac effects (including elevation of carboxyhemoglobin), central nervous system effects, liver effects, and skin and eye irritation.

* * * * *

31. Amend § 1910.1200 as follows:

A. Remove the word “material” before the word “safety” in the phrase “material safety data sheet” wherever it appears in paragraphs (b)(3)(ii) and (iv), (b)(4)(ii) five times, (e)(1) introductory text, (e)(1)(i), (e)(2)(i), (g)(heading), (g)(1) two times, (g)(4), (6)(i) two times, (g)(6)(ii) through (iv), (g)(7)(i) two times, (g)(7)(ii), (g)(7)(iii) two times, (g)(7)(iv) two times, (g)(7)(v) two times, (g)(7)(vi) and (vii), (g)(8) two times, (g)(9), (g)(10), (h)(l), (h)(2)(iii),and (i)(1)(ii);

B. Remove the following definitions in paragraph (c) Combustible liquid, Compressed gas, Explosive, Flammable, Flashpoint, Hazard warning, Identity, Material Data Safety Sheet (MSDS), Organic peroxide, Oxidizer, Pyrophoric, Unstable (reactive), and Water reactive;

C. Revise the following definitions in paragraph (c) Chemical, Chemical name, Health hazard, Label, Mixture, Physical hazard, and Trade secret;

D. Revise the definition of the term “Hazardous chemical” and relocate it in alphabetical order in paragraph (c).

E. Add the following definitions in alphabetical order in paragraph (c) in alphabetical order Classification, Hazard category, Hazard class, Hazard statement, Label element, Pictogram, Precautionary statement, Product identifier, Safety Data Sheet (SDS), Signal word, Substance and Unclassified Hazard;

F. Revise paragraphs (a)(1), (a)(2), (b)(1), (d) (heading), (d)(1) through (d)(3), (f), (g)(2), (g)(3), (g)(5), (g)(11), (h)(3)(iv), (i)(1), (i)(1)(iii) and (iv), (i)(2), (i)(3), (i)(3)(iii), (i)(7), (i)(7)(iii), (i)(7)(v), (i)(9)(i), (i)(10)(i), (i)(10)(ii), (i)(11), and (i)(13), and (j);

G. Remove Appendices A, B, and E to § 1910.1200; redesignate Appendix D to § 1910.1200 as Appendix E to § 1910.1200 and add new Appendices A, B, C, D and F to § 1910.1200.

The revisions and additions read as follows:

§ 1910.1200 Hazard communication.

(a) Purpose.

(1) The purpose of this section is to ensure that the hazards of all chemicals produced or imported are classified, and that information concerning the classified hazards is transmitted to employers and employees. The requirements of this section are intended to be consistent with the provisions of the United Nations Globally Harmonized System of Classification and Labeling of Chemicals (GHS), Revision 3. The transmittal of information is to be accomplished by means of comprehensive hazard communication programs, which are to include container labeling and other forms of warning, safety data sheets and employee training.

* * * * *

(2) This occupational safety and health standard is intended to address comprehensively the issue of classifying the potential hazards of chemicals, and communicating information concerning hazards and appropriate protective measures to employees, and to preempt any legal requirements of a state, or political subdivision of a state, pertaining to this subject. Classifying the potential hazards of chemicals and communicating information concerning hazards and appropriate protective measures to employees, may include, for example, but is not limited to, provisions for: developing and maintaining a written hazard communication program for the workplace, including lists of hazardous chemicals present; labeling of containers of chemicals in the workplace, as well as of containers of chemicals being shipped to other workplaces; preparation and distribution of safety data sheets to employees and downstream employers; and development and implementation of employee training programs regarding hazards of chemicals and protective measures. Under section 18 of the Act, no state or political subdivision of a state may adopt or enforce, through any court or agency, any requirement relating to the issue addressed by this Federal standard, except pursuant to a Federally-approved state plan.

(b) * * *

(1) This section requires chemical manufacturers or importers to classify the hazards of chemicals which they produce or import, and all employers to provide information to their employees about the hazardous chemicals to which they are exposed, by means of a hazard communication program, labels and other forms of warning, safety data sheets, and information and training. In addition, this section requires distributors to transmit the required information to employers. (Employers who do not produce or import chemicals need only focus on those parts of this rule that deal with establishing a workplace program and communicating information to their workers.)

* * * * *

(c) * * *

Chemical means any substance, or mixture of substances.

* * * * *

Chemical name means the scientific designation of a chemical in accordance with the nomenclature system developed by the International Union of Pure and Applied Chemistry (IUPAC) or the Chemical Abstracts Service (CAS) rules of nomenclature, or a name that will clearly identify the chemical for the purpose of conducting a hazard classification.

Classification means to identify the relevant data regarding the hazards of a chemical; review those data to ascertain the hazards associated with the chemical; and decide whether the chemical will be classified as hazardous, and the degree of hazard where appropriate, by comparing the data with the criteria for health and physical hazards.

Hazard category means the division of criteria within each hazard class, e.g., oral acute toxicity and flammable liquids include 4 hazard categories. These categories compare hazard severity within a hazard class and should not be taken as a comparison of hazard categories more generally.

Hazard class means the nature of the physical or health hazards, e.g., flammable solid, carcinogen, oral acute toxicity.

Hazard statement means a statement assigned to a hazard class and category that describes the nature of the hazard(s) of a chemical, including, where appropriate, the degree of hazard.

Hazardous chemical means any chemical which is classified as a physical hazard or a health hazard, or an unclassified hazard as defined in this section.

* * * * *

Health hazard means a chemical that is classified as posing one of the following hazardous effects: acute toxicity (any route of exposure); skin corrosion or irritation; serious eye damage or eye irritation; respiratory or skin sensitization; germ cell mutagenicity; carcinogenicity; reproductive toxicity; specific target organ toxicity (single or repeated exposure); or aspiration hazard. The criteria for determining whether a chemical is classified as a health hazard are detailed in Appendix A to § 1910.1200—Health Hazard Criteria.

* * * * *

Label means an appropriate group of written, printed or graphic information elements concerning a hazardous chemical, that is affixed to, printed on, or attached to the immediate container of a hazardous chemical, or to the outside packaging.

Label elements means the specified pictogram, hazard statement, signal word and precautionary statement for each hazard class and category.

Mixture means a combination or a solution composed of two or more substances in which they do not react.

Physical hazard means a chemical that is classified as posing one of the following hazardous effects: explosive; flammable (gases, aerosols, liquids, or solids); oxidizer (liquid, solid or gas); self-reactive; pyrophoric (liquid or solid); self-heating; organic peroxide; corrosive to metal; gas under pressure; or in contact with water emits flammable gas. See Appendix B to § 1910.1200—Physical Hazard Criteria.

Pictogram means a composition that may include a symbol plus other graphic elements, such as a border, background pattern, or color, that is intended to convey specific information about the hazards of a chemical. Eight pictograms are designated under this standard for application to a hazard category.

Precautionary statement means a phrase that describes recommended measures that should be taken to minimize or prevent adverse effects resulting from exposure to a hazardous chemical, or improper storage or handling.

* * * * *

Product identifier means the name or number used for a hazardous chemical on a label or in the SDS. It provides a unique means by which the user can identify the chemical. The product identifier used shall permit cross-references to be made among the required list of hazardous chemicals, the label and the SDS.

* * * * *

Safety data sheet (SDS) means written or printed material concerning a hazardous chemical that is prepared in accordance with paragraph (g) of this section.

Signal word means a word used to indicate the relative level of severity of hazard and alert the reader to a potential hazard on the label. The signal words used in this section are “danger” and “warning.” “Danger” is used for the more severe hazards, while “warning” is used for the less severe.

* * * * *

Substance means chemical elements and their compounds in the natural state or obtained by any production process, including any additive necessary to preserve the stability of the product and any impurities deriving from the process used, but excluding any solvent which may be separated without affecting the stability of the substance or changing its composition.

Trade secret means any confidential formula, pattern, process, device, information or compilation of information that is used in an employer's business, and that gives the employer an opportunity to obtain an advantage over competitors who do not know or use it. Appendix E to § 1910.1200—Definition of Trade Secret, sets out the criteria to be used in evaluating trade secrets.

Unclassified hazard means a chemical for which there is scientific evidence identified during the classification process that it may pose an adverse physical or health effect when present in a workplace under normal conditions of use or in a foreseeable emergency, but the evidence does not currently meet the specified criteria for physical or health hazard classification in this section. This does not include adverse physical and health effects for which there is a hazard class addressed in this section.

* * * * *

(d) Hazard classification.

(1) Chemical manufacturers and importers shall evaluate chemicals produced in their workplaces or imported by them to classify their health and physical hazards in accordance with this section. For each chemical, the chemical manufacturer or importer shall determine the hazard classes, and the category of each class that apply to the chemical being classified. Employers are not required to classify chemicals unless they choose not to rely on the classification performed by the chemical manufacturer or importer for the chemical to satisfy this requirement.

(2) Chemical manufacturers, importers or employers classifying chemicals shall identify and consider the full range of available scientific literature and other evidence concerning the potential hazards. There is no requirement to test the chemical to determine how to classify its hazards. Appendix A to § 1910.1200 shall be consulted for classification of health hazards, and Appendix B to § 1910.1200 shall be consulted for the classification of physical hazards.

(3) Mixtures.

(i) Chemical manufacturers, importers, or employers evaluating chemicals shall follow the procedures described in Appendixes A and B to § 1910.1200 to classify the hazards of the chemicals, including determinations regarding when mixtures of the classified chemicals are covered by this section.

(ii) A chemical manufacturer or importer of a mixture shall be responsible for the accuracy of the classification of the mixture even when relying on the classifications for individual ingredients received from the ingredient manufacturers or importers on the safety data sheets.

* * * * *

(f) Labels and other forms of warning.

(1) Labels on shipped containers. The chemical manufacturer, importer, or distributor shall ensure that each container of classified hazardous chemicals leaving the workplace is labeled, tagged or marked with the following information:

(i) Product identifier;

(ii) Signal word;

(iii) Hazard statement(s);

(iv) Pictogram(s);

(v) Precautionary statement(s); and,

(vi) Name, address, and telephone number of the chemical manufacturer, importer, or other responsible party.

(2) For unclassified hazards, the label shall include the name of the chemical, the name, address, and telephone number of the manufacturer, importer, or other responsible party, and, provide as supplementary information, a description of the unclassified hazards and appropriate precautionary measures to ensure the safe handling and use of the chemical.

(3) The chemical manufacturer, importer, or distributor shall ensure that the information provided under (f)(1)(i) through (v) is in accordance with Appendix C, Allocation of Label Elements, for each hazard class and associated hazard category for the hazardous chemical, prominently displayed, and in English (other languages may also be included if appropriate).

(4) The chemical manufacturer, importer, or distributor shall ensure that the information provided under (f)(1)(ii) through (iv) is located together on the label, tag, or mark.

(5)(i) For solid metal (such as a steel beam or a metal casting), solid wood, or plastic items that are not exempted as articles due to their downstream use, or shipments of whole grain, the required label may be transmitted to the customer at the time of the initial shipment, and need not be included with subsequent shipments to the same employer unless the information on the label changes;

(ii) The label may be transmitted with the initial shipment itself, or with the safety data sheet that is to be provided prior to or at the time of the first shipment; and,

(iii) This exception to requiring labels on every container of hazardous chemicals is only for the solid material itself, and does not apply to hazardous chemicals used in conjunction with, or known to be present with, the material and to which employees handling the items in transit may be exposed (for example, cutting fluids or pesticides in grains).

(6) Chemical manufacturers, importers, or distributors shall ensure that each container of hazardous chemicals leaving the workplace is labeled, tagged, or marked in accordance with this section in a manner which does not conflict with the requirements of the Hazardous Materials Transportation Act (49 U.S.C. 1801 et seq.) and regulations issued under that Act by the Department of Transportation.

(7) Workplace labeling. Except as provided in paragraphs (f)(8) and (f)(9) of this section, the employer shall ensure that each container of hazardous chemicals in the workplace is labeled, tagged or marked with either:

(i) The information specified under (f)(1)(i) through (v) for labels on shipped containers; or,

(ii) Product identifier and words, pictures, symbols, or combination thereof, which provide at least general information regarding the hazards of the chemicals, and which, in conjunction with the other information immediately available to employees under the hazard communication program, will provide employees with the specific information regarding the physical and health hazards of the hazardous chemical.

(8) The employer may use signs, placards, process sheets, batch tickets, operating procedures, or other such written materials in lieu of affixing labels to individual stationary process containers, as long as the alternative method identifies the containers to which it is applicable and conveys the information required by paragraph (f)(7) of this section to be on a label. The employer shall ensure the written materials are readily accessible to the employees in their work area throughout each work shift.

(9) The employer is not required to label portable containers into which hazardous chemicals are transferred from labeled containers, and which are intended only for the immediate use of the employee who performs the transfer. For purposes of this section, drugs which are dispensed by a pharmacy to a health care provider for direct administration to a patient are exempted from labeling.

(10) The employer shall not remove or deface existing labels on incoming containers of hazardous chemicals, unless the container is immediately marked with the required information.

(11) The employer shall ensure that workplace labels or other forms of warning are legible, in English, and prominently displayed on the container, or readily available in the work area throughout each work shift. Employers having employees who speak other languages may add the information in their language to the material presented, as long as the information is presented in English as well.

(12) Chemical manufacturers, importers, distributors, or employers who become newly aware of any significant information regarding the hazards of a chemical shall revise the labels for the chemical within three months of becoming aware of the new information, and shall ensure that labels on containers of hazardous chemicals shipped after that time contain the new information. If the chemical is not currently produced or imported, the chemical manufacturer, importer, distributor, or employer shall add the information to the label before the chemical is shipped or introduced into the workplace again.

* * * * *

(g) * * *

(2) The chemical manufacturer or importer preparing the safety data sheet shall ensure that it is in English (although the employer may maintain copies in other languages as well), and includes the following section numbers and headings, and associated information under each heading, in the order listed (See Appendix D to § 1910.1200—Safety Data Sheets, for the specific content of each section of the safety data sheet.)

(i) Section 1, Identification;

(ii) Section 2, Hazard(s) identification;

(iii) Section 3, Composition/information on ingredients;

(iv) Section 4, First-aid measures;

(v) Section 5, Fire-fighting measures;

(vi) Section 6, Accidental release measures;

(vii) Section 7, Handling and storage;

(viii) Section 8, Exposure controls/personal protection;

(ix) Section 9, Physical and chemical properties;

(x) Section 10, Stability and reactivity;

(xi) Section 11, Toxicological information.

Note 1 to paragraph (g)(2):

To be consistent with the GHS, an SDS must also include the following headings in this order:

Section 12, Ecological information;

Section 13, Disposal considerations;

Section 14, Transport information; and

Section 15, Regulatory information.

Note 2 to paragraph (g)(2):

OSHA will not be enforcing information requirements in sections 12 through 15, as these areas are not under its jurisdiction.

(xii) Section 16, Other information, including date of preparation or last revision.

(g)(3) If no relevant information is found for any sub-heading within a section on the safety data sheet, the chemical manufacturer, importer or employer preparing the safety data sheet shall mark it to indicate that no applicable information was found.

* * * * *

(5) The chemical manufacturer, importer or employer preparing the safety data sheet shall ensure that the information provided accurately reflects the scientific evidence used in making the hazard classification. If the chemical manufacturer, importer or employer preparing the safety data sheet becomes newly aware of any significant information regarding the hazards of a chemical, or ways to protect against the hazards, this new information shall be added to the safety data sheet within three months. If the chemical is not currently being produced or imported the chemical manufacturer or importer shall add the information to the safety data sheet before the chemical is introduced into the workplace again.

* * * * *

(11) Safety data sheets shall also be made readily available, upon request, to designated representatives, the Assistant Secretary, and the Director, in accordance with the requirements of 29 CFR 1910.1020(e).

(h) * * *

(3) * * *

(iv) The details of the hazard communication program developed by the employer, including an explanation of the labels received on shipped containers and the workplace labeling system used by the employer; the safety data sheet, including the order of information and how employees can obtain and use the appropriate hazard information.

(i) * * *

(1) The chemical manufacturer, importer, or employer may withhold the specific chemical identity, including the chemical name, other specific identification of a hazardous chemical, or the exact percentage of the substance in a mixture, from the safety data sheet, provided that:

* * * * *

(iii) The safety data sheet indicates that the specific chemical identity and/or percentage of composition is being withheld as a trade secret; and,

(iv) The specific chemical identity and percentage is made available to health professionals, employees, and designated representatives in accordance with the applicable provisions of this paragraph.

(2) Where a treating physician or nurse determines that a medical emergency exists and the specific chemical identity and/or specific percentage of composition of a hazardous chemical is necessary for emergency or first-aid treatment, the chemical manufacturer, importer, or employer shall immediately disclose the specific chemical identity or percentage composition of a trade secret chemical to that treating physician or nurse, regardless of the existence of a written statement of need or a confidentiality agreement. The chemical manufacturer, importer, or employer may require a written statement of need and confidentiality agreement, in accordance with the provisions of paragraphs (i)(3) and (4) of this section, as soon as circumstances permit.

(3) In non-emergency situations, a chemical manufacturer, importer, or employer shall, upon request, disclose a specific chemical identity or percentage composition, otherwise permitted to be withheld under paragraph (i)(1) of this section, to a health professional (i.e. physician, industrial hygienist, toxicologist, epidemiologist, or occupational health nurse) providing medical or other occupational health services to exposed employee(s), and to employees or designated representatives, if:

* * * * *

(iii) The request explains in detail why the disclosure of the specific chemical identity or percentage composition is essential and that, in lieu thereof, the disclosure of the following information to the health professional, employee, or designated representative, would not satisfy the purposes described in paragraph (i)(3)(ii) of this section:

* * * * *

(7) If the chemical manufacturer, importer, or employer denies a written request for disclosure of a specific chemical identity or percentage composition, the denial must:

* * * * *

(iii) Include evidence to support the claim that the specific chemical identity or percent of composition is a trade secret;

* * * * *

(v) Explain in detail how alternative information may satisfy the specific medical or occupational health need without revealing the trade secret.

* * * * *

(9) * * *

(i) The chemical manufacturer, importer, or employer has supported the claim that the specific chemical identity or percentage composition is a trade secret;

* * * * *

(10) * * *

(i) If OSHA determines that the specific chemical identity or percentage composition requested under paragraph (i)(3) of this section is not a “bona fide” trade secret, or that it is a trade secret, but the requesting health professional, employee, or designated representative has a legitimate medical or occupational health need for the information, has executed a written confidentiality agreement, and has shown adequate means to protect the confidentiality of the information, the chemical manufacturer, importer, or employer will be subject to citation by OSHA.

(ii) If a chemical manufacturer, importer, or employer demonstrates to OSHA that the execution of a confidentiality agreement would not provide sufficient protection against the potential harm from the unauthorized disclosure of a trade secret, the Assistant Secretary may issue such orders or impose such additional limitations or conditions upon the disclosure of the requested chemical information as may be appropriate to assure that the occupational health services are provided without an undue risk of harm to the chemical manufacturer, importer, or employer.

* * * * *

(11) If a citation for a failure to release trade secret information is contested by the chemical manufacturer, importer, or employer, the matter will be adjudicated before the Occupational Safety and Health Review Commission in accordance with the Act's enforcement scheme and the applicable Commission rules of procedure. In accordance with the Commission rules, when a chemical manufacturer, importer, or employer continues to withhold the information during the contest, the Administrative Law Judge may review the citation and supporting documentation “in camera” or issue appropriate orders to protect the confidentiality of such matters.

* * * * *

(13) Nothing in this paragraph (i) shall be construed as requiring the disclosure under any circumstances of process information which is a trade secret.

(j) Effective dates. (1) Employers shall train employees regarding the new labels and safety data sheets by [date 2 years after the publication of the final rule].

(2) Chemical manufacturers, importers, distributors, and employers shall be in compliance with all modified provisions of this section no later than [date 3 years after the publication of the final rule].

(3) Chemical manufacturers, importers, distributors, and employers may comply with either 29 CFR 1910.1200 revised as of October 1, 2009, or the modified version of this standard, or both during the 3-year transition period.

Appendix A to § 1910.1200—Health Hazard Criteria (Mandatory) Back to Top

A.0GENERAL CLASSIFICATION CONSIDERATIONS Back to Top

A.0.1Classification Back to Top

A.0.1.1The term “hazard classification” is used to indicate that only the intrinsic hazardous properties of chemicals are considered. Hazard classification incorporates three steps:

(a) identification of relevant data regarding the hazards of a chemical;

(b) subsequent review of those data to ascertain the hazards associated with the chemical;

(c) determination of whether the chemical will be classified as hazardous and the degree of hazard.

A.0.1.2For many hazard classes, the criteria are semi-quantitative or qualitative and expert judgment is required to interpret the data for classification purposes.

A.0.2Available Data, Test Methods and Test Data Quality Back to Top

A.0.2.1There is no requirement for testing chemicals.

A.0.2.2The criteria for determining health hazards are test method neutral, i.e., they do not specify particular test methods, as long as the methods are scientifically validated procedures.

A.0.2.3The term “scientifically validated” refers to the process by which the reliability and the relevance of a procedure are established for a particular purpose.

A.0.2.4Existing test data are acceptable for classifying chemicals, although expert judgment also may be needed for classification purposes.

A.0.2.5The effect of a chemical on biological systems is influenced by the physico-chemical properties of the substance and/or ingredients of the mixture and the way in which ingredient substances are biologically available. A chemical need not be classified when it can be shown by conclusive experimental data from scientifically validated test methods that the chemical is not biologically available.

A.0.2.6For classification purposes, epidemiological data and experience on the effects of chemicals on humans (e.g., occupational data, data from accident databases) shall be taken into account in the evaluation of human health hazards of a chemical.

A.0.3Classification Based on Weight of Evidence Back to Top

A.0.3.1For some hazard classes, classification results directly when the data satisfy the criteria. For others, classification of a chemical shall be determined on the basis of the total weight of evidence using expert judgment. This means that all available information bearing on the classification of hazard shall be considered together, including the results of valid in vitro tests, relevant animal data, and human experience such as epidemiological and clinical studies and well-documented case reports and observations.

A.0.3.2The quality and consistency of the data shall be considered. Information on chemicals related to the material being classified shall be considered as appropriate, as well as site of action and mechanism or mode of action study results. Both positive and negative results shall be assembled together in a single weight of evidence determination.

A.0.3.3Positive effects which are consistent with the criteria for classification, whether seen in humans or animals, shall normally justify classification. Where evidence is available from both humans and animals and there is a conflict between the findings, the quality and reliability of the evidence from both sources shall be evaluated in order to resolve the question of classification. Reliable, good quality human data shall generally have precedence over other data. However, even well-designed and conducted epidemiological studies may lack a sufficient number of subjects to detect relatively rare but still significant effects, or to assess potentially confounding factors. Therefore, positive results from well-conducted animal studies are not necessarily negated by the lack of positive human experience but require an assessment of the robustness, quality and statistical power of both the human and animal data.

A.0.3.4Route of exposure, mechanistic information, and metabolism studies are pertinent to determining the relevance of an effect in humans. When such information raises doubt about relevance in humans, a lower classification may be warranted. When there is scientific evidence demonstrating that the mechanism or mode of action is not relevant to humans, the chemical should not be classified.