Skip to Content

Notice

Notice of Granted Buy America Waivers

Document Details

Information about this document as published in the Federal Register.

Published Document

This document has been published in the Federal Register. Use the PDF linked in the document sidebar for the official electronic format.

Start Preamble

AGENCY:

Federal Transit Administration (FTA), DOT.

ACTION:

Notice of granted Buy America waiver.

SUMMARY:

The following waivers allow New Flyer of America and the North American Bus Industries (NABI) to count a foreign-manufactured articulating joint system used in low and standard floor bus as a domestic component for purposes of calculating the aggregate domestic content of the vehicle and was predicated on the non-availability of the item in the domestic market. The New Flyer waiver was granted on April 24, 2003, and the NABI waiver on May 9, 2003. For reasons discussed in the text of the waivers, both expire on July 1, 2004. This notice shall insure that the public is aware of the waivers. FTA requests that the public notify it of any relevant changes in the domestic articulating joint market.

Start Further Info

FOR FURTHER INFORMATION CONTACT:

Meghan G. Ludtke, FTA Office of Chief Counsel, Room 9316, (202) 366-1936 (telephone) or (202) 366-3809 (fax).

End Further Info End Preamble Start Supplemental Information

SUPPLEMENTARY INFORMATION:

See waivers below.

Start Signature

Issued: June 9, 2003.

Jennifer L. Dorn,

Administrator.

End Signature

April 24, 2003.

Mr. Paul Smith,

Vice President, Sales and Marketing, New Flyer of America, 711 Kerneghan Avenue, Winnipeg, Manitoba, Canada R2C 3T4.

Mr. Smith: This letter responds to your correspondence of March 24, 2003, in which New Flyer of America (New Flyer) requests a non-availability waiver of the Buy America requirements for the procurement of the Hubner Manufacturing Corporation (Hubner) articulated joint system for New Flyer's low floor buses.

The Federal Transit Administration's (FTA) requirements concerning domestic preference for federally funded transit projects are set forth in 49 U.S.C. 5323(j). Section 5323(j)(2)(C) addresses the general requirements for the procurement of rolling stock. This section provides that all rolling stock procured with FTA funds must have a domestic content of at least 60 percent and must undergo final assembly in the U.S. You request a waiver under 49 U.S.C. 5323(j)(2)(B), which states the Buy America requirements shall not apply if the item or items are not produced in the U.S. in sufficient and reasonably available quantities or are not of a satisfactory quality. The implementing regulation provides that non-availability waivers may be granted for a component of rolling stock. 49 CFR 661.7(f).

FTA post a summary of this waiver request on its website and requested comment. We received four comments, one against and three in favor of granting the waiver.[1] The comment against the waiver argues that the Buy America rules for rolling stock already allow a waiver of up to forty percent foreign content, and when a component is unavailable from a domestic source, the vehicle maker should use part of its allotted foreign content. However, as noted above, the regulation currently allows component waivers for rolling stock when the product is not available from a domestic source. FTA received no comments indicating that these articulating joint systems are available from a U.S. source.

Based on a thorough review of the industry, FTA previously granted a two-year non-availability waiver to Newflyer for this articulated joint system on April 24, 2001. You state that the circumstances necessitating the current waiver remain unchanged and in the near term, New Flyer must still use the Hubner joint, which is still not available from a domestic source.

In response to the original waiver, FTA received a comment from a U.S. bellows Start Printed Page 35250manufacturer, A&A Manufacturing, expressing concern that because the articulated joint system is made of separate subcomponents that could be supplied separately by different manufacturers, the waiver effectively prevented A&A from selling its product, the bellows, to New Flyer's response stated that in the low floor bus, the articulated joints are purchased as an entire unit and any changes or integration of a subcomponent, such as new bellows, would require sufficient time to design, integrate and test.

On January 17, 2001, FTA directed Newflyer to work with domestic suppliers for these parts to develop alternative sources. We noted that this good faith effort to qualify new domestic suppliers would be considered should New Flyer request a renewal of the waiver. Newflyer now informs FTA that it plans to install an articulated joint, utilizing A&A's bellows and manufactured by a domestic manufacturer, in August 2003. The requisite testing should be completed by April 2004. FTA has also been advised by Hubner Manufacturing, that it plans to relocate the entire articulation systems manufacturing process from Germany to South Carolina by the end of 2003.

Based on the information you have provided, I have determined that the grounds for a non-availability waiver still exist. Therefore, pursuant to the provisions of 49 U.S.C. 5323(j)(2)(B), a waiver is granted for the procurement of Hubner's articulated joint system for New Flyer low floor buses until June 30, 2004, as requested. The waiver will allow time for Hubner's relocation to the U.S. and completion of necessary testing for the alternate U.S. joint system. In order to insure that the public is aware of this waiver, particularly potential manufacturers, this waiver will be published in the Federal Register.

If you have any questions, please contact Meghan G. Ludtke at (202) 366-1935.

  Very truly yours,

Gregory B. McBride,

Deputy Chief Counsel.

May 9, 2003.

Mr. Bill Coryell,

Vice President, Marketing and Sales, North American Bus Industries, Inc., 20350 Ventura Blvd., Suite 205, Woodland Hills, California 91364.

Dear Mr. Coryell: This letter responds to your correspondence of April 22, 2003, in which North American Bus Industries, Inc. (NABI) requests a non-availability waiver of the Buy America requirements for the procurement of the Hubner Manufacturing Corporation (Hubner) articulated joint system for use in NABI's low floor and standard floor articulated buses. The system is comprised of a mechanical articulating joint incorporating an electronically controlled, hydraulic damping subsystem.

The Federal Transit Administration's (FTA) requirements concerning domestic preference for federally funded transit projects are set forth in 49 U.S.C. 5323(j). Section 5323(j)(2)(C) addresses the general requirements for the procurement of rolling stock. This section provides that all rolling stock procured with FTA funds must have a domestic content of at least 60 percent and must undergo final assembly in the U.S. You request a waiver under 49 U.S.C. 5323(j)(2)(B), which states the Buy America requirements shall not apply if the item or items are not produced in the U.S. in sufficient and reasonably available quantities or are not of a satisfactory quality. The implementing regulation provides that non-availability waivers may be granted for a component of rolling stock. 49 CFR 661.7(f).

FTA posted a request for comments and received one comment against the waiver. Gillig Corporation argues that the Buy America rules for rolling stock already allow a waiver of up to forty percent foreign content, and when a component is unavailable from a domestic source, the vehicle maker should use part of its allotted foreign content. However, as noted above, the regulation currently allows component waivers for rolling stock when the product is not available from a domestic source. FTA received no comments indicating that these articulating joint systems are available from a U.S. source. We received two comments in favor of the waiver, one from Hubner, the subject joint manufacturer, and the other from CAPtech, Inc., which argues that allowing foreign manufacturers into the market place will result in better U.S. products.

FTA issued a similar waiver to New Flyer of America on April 24, 2001, which was valid until April 24, 2003. Based in part on the waiver issued to New Flyer in 2001, NABI requested a similar waiver on August 9, 2002. In grating NABI's waiver, we wrote “we will grant this waiver to NABI for all solicitations responded to until April 24, 2003, which is when New Flyer's waiver expires. We will then evaluate the situation with respect to all vehicle and articulating joint manufacturers.” New Flyer and NABI have both requested a renewal of this waiver and on April 24, 2003, FTA issued another waiver to New Flyer.

You state that the circumstances necessitating the current waiver remain unchanged and in the near term, NABI must still use the Hubner joint, which is still not available from a domestic source. FTA has been advised by Hubner Manufacturing that it plans to relocate the entire articulation systems manufacturing process from Germany to South Carolina by the end of 2003. Based on a review of the industry and the information provided by New Flyer, NABI, and Hubner, I have determined that the grounds for a non-availability waiver still exist. Therefore, pursuant to the provisions of 49 U.S.C. 5323(j)(2)(B), and consistent with the waiver issued to New Flyer on April 24, 2003, a waiver is granted for the procurement of Hubner's articulated joint system for NABI's low floor and standard buses until June 30, 2004. This waiver will allow time for Hubner's relocation to the U.S. In order to insure that the public is aware of this waiver, particularly potential manufacturers, this waiver will be published in the Federal Register.

If you have any questions, please contact Meghan G. Ludtke at (202) 366-1936.

  Very Truly yours,

Gregory B. McBride,

Deputy Chief Counsel.

End Supplemental Information

Footnotes

1.  The comment against the waiver was from Gillig Corporation. The comments in favor of the waiver were from CAPtech, Inc., North American Bus Industries, and Hubner Manufacturing.

Back to Citation

[FR Doc. 03-14888 Filed 6-11-03; 8:45 am]

BILLING CODE 4910-57-M