Skip to Content

Proposed Rule

Airworthiness Directives; Airbus Model A310 Airplanes

Document Details

Information about this document as published in the Federal Register.

Published Document

This document has been published in the Federal Register. Use the PDF linked in the document sidebar for the official electronic format.

Start Preamble

AGENCY:

Federal Aviation Administration (FAA), Department of Transportation (DOT).

ACTION:

Notice of proposed rulemaking (NPRM).

SUMMARY:

The FAA proposes to adopt a new airworthiness directive (AD) for all Airbus Model A310 airplanes. This proposed AD would require doing repetitive inspections for any missing, damaged, or incorrectly installed wiper rings in the splined couplings of the flap transmissions shafts; inspections for any missing, damaged, or incorrectly installed rubber gaiters and straps on the sliding bearing/plunging joints of the flap transmission; and corrective action if necessary. This proposed AD Start Printed Page 58321results from reviews in which the manufacturer determined that the splined couplings and sliding bearings of the flap transmission system could be affected by corrosion and wear. We are proposing this AD to detect and correct damaged, missing, or incorrectly installed components of the flap transmission system, which could result in reduced functional integrity of the flap transmission system and consequent reduced control of the airplane.

DATES:

We must receive comments on this proposed AD by November 2, 2006.

ADDRESSES:

Use one of the following addresses to submit comments on this proposed AD.

  • DOT Docket Web site: Go to http://dms.dot.gov and follow the instructions for sending your comments electronically.
  • Government-wide rulemaking Web site: Go to http://www.regulations.gov and follow the instructions for sending your comments electronically.
  • Mail: Docket Management Facility, U.S. Department of Transportation, 400 Seventh Street, SW., Nassif Building, room PL-401, Washington, DC 20590.
  • Fax: (202) 493-2251.
  • Hand Delivery: Room PL-401 on the plaza level of the Nassif Building, 400 Seventh Street, SW., Washington, DC, between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays.

Contact Airbus, 1 Rond Point Maurice Bellonte, 31707 Blagnac Cedex, France, for service information identified in this proposed AD.

Start Further Info

FOR FURTHER INFORMATION CONTACT:

Tom Stafford, Aerospace Engineer, International Branch, ANM-116, FAA, Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, Washington 98057-3356; telephone (425) 227-1622; fax (425) 227-1149.

End Further Info End Preamble Start Supplemental Information

SUPPLEMENTARY INFORMATION:

Comments Invited

We invite you to submit any relevant written data, views, or arguments regarding this proposed AD. Send your comments to an address listed in the ADDRESSES section. Include the docket number “FAA-2006-25966; Directorate Identifier 2006-NM-149-AD” at the beginning of your comments. We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of the proposed AD. We will consider all comments received by the closing date and may amend the proposed AD in light of those comments.

We will post all comments we receive, without change, to http://dms.dot.gov, including any personal information you provide. We will also post a report summarizing each substantive verbal contact with FAA personnel concerning this proposed AD. Using the search function of that Web site, anyone can find and read the comments in any of our dockets, including the name of the individual who sent the comment (or signed the comment on behalf of an association, business, labor union, etc.). You may review the DOT's complete Privacy Act Statement in the Federal Register published on April 11, 2000 (65 FR 19477-78), or you may visit http://dms.dot.gov.

Examining the Docket

You may examine the AD docket on the Internet at http://dms.dot.gov, or in person at the Docket Management Facility office between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The Docket Management Facility office (telephone (800) 647-5227) is located on the plaza level of the Nassif Building at the DOT street address stated in the ADDRESSES section. Comments will be available in the AD docket shortly after the Docket Management System receives them.

Discussion

The European Aviation Safety Agency (EASA), which is the airworthiness authority for the European Union, notified us that an unsafe condition may exist on all Airbus Model A310 airplanes. The EASA advises that the manufacturer conducted high-time equipment reviews as part of the Model A310 aircraft design service goal extension work. The manufacturer determined that the splined couplings and sliding bearings of the flap transmission system could be affected by corrosion and wear. In addition, the manufacturer determined that the protective components of the flap transmission system could be defective. The protective components include the wiper rings and rubber gaiters. This condition, if not corrected, could result in reduced functional integrity of the flap transmission system and consequent reduced control of the airplane.

Relevant Service Information

Airbus has issued Service Bulletin A310-27-2099, dated February 17, 2006. The service bulletin describes procedures for doing an inspection for any missing, damaged, or incorrectly installed wiper rings in the splined couplings of the flap transmission shafts; an inspection for any missing, damaged, or incorrectly installed rubber gaiters and straps on the sliding bearing/plunging joints of the flap transmission; and corrective action if necessary. The corrective action is replacing any damaged, missing, or incorrectly installed wiper rings, rubber gaiters, or straps with serviceable components. Accomplishing the actions specified in the service information is intended to adequately address the unsafe condition. The EASA mandated the service information and issued airworthiness directive 2006-0111, dated May 12, 2006, to ensure the continued airworthiness of these airplanes in the European Union.

FAA's Determination and Requirements of the Proposed AD

These airplane models are manufactured in France and are type certificated for operation in the United States under the provisions of section 21.29 of the Federal Aviation Regulations (14 CFR 21.29) and the applicable bilateral airworthiness agreement. As described in FAA Order 8100.14A, “Interim Procedures for Working with the European Community on Airworthiness Certification and Continued Airworthiness,” dated August 12, 2005, the EASA has kept the FAA informed of the situation described above. We have examined the EASA's findings, evaluated all pertinent information, and determined that we need to issue an AD for products of this type design that are certificated for operation in the United States.

Therefore, we are proposing this AD, which would require accomplishing the actions specified in the service information described previously.

Clarification of Type of Inspection

The service bulletin specifies to “visually inspect” the flap transmission shafts. We have determined that the procedures in the service bulletin should be described as a “general visual inspection.” Note 1 has been included in this proposed AD to define this type of inspection.

Costs of Compliance

The following table provides the estimated costs for U.S. operators to comply with this proposed AD. Start Printed Page 58322

Estimated Costs

ActionWork hoursAverage labor rate per hourCost per airplaneNumber of U.S.- registered airplanesFleet cost
Inspection, per inspection cycle3$80$2403$15,120, per inspection cycle.

Authority for This Rulemaking

Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, Section 106, describes the authority of the FAA Administrator. Subtitle VII, Aviation Programs, describes in more detail the scope of the Agency's authority.

We are issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section 44701, “General requirements.” Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.

Regulatory Findings

We have determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government.

For the reasons discussed above, I certify that the proposed regulation:

1. Is not a “significant regulatory action” under Executive Order 12866;

2. Is not a “significant rule” under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and

3. Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.

We prepared a regulatory evaluation of the estimated costs to comply with this proposed AD and placed it in the AD docket. See the ADDRESSES section for a location to examine the regulatory evaluation.

Start List of Subjects

List of Subjects in 14 CFR Part 39

End List of Subjects

The Proposed Amendment

Accordingly, under the authority delegated to me by the Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

Start Part

PART 39—AIRWORTHINESS DIRECTIVES

1. The authority citation for part 39 continues to read as follows:

Start Authority

Authority: 49 U.S.C. 106(g), 40113, 44701.

End Authority
[Amended]

2. The Federal Aviation Administration (FAA) amends § 39.13 by adding the following new airworthiness directive (AD):

Airbus: Docket No. FAA-2006-25966; Directorate Identifier 2006-NM-149-AD.

Comments Due Date

(a) The FAA must receive comments on this AD action by November 2, 2006.

Affected ADs

(b) None.

Applicability

(c) This AD applies to all Airbus Model A310 airplanes, certificated in any category.

Unsafe Condition

(d) This AD results from reviews in which the manufacturer determined that the splined couplings and sliding bearings of the flap transmission system could be affected by corrosion and wear. We are issuing this AD to detect and correct damaged, missing, or incorrectly installed components of the flap transmission system, which could result in reduced functional integrity of the flap transmission system and consequent reduced control of the airplane.

Compliance

(e) You are responsible for having the actions required by this AD performed within the compliance times specified, unless the actions have already been done.

Initial and Repetitive Inspections

(f) Within 2,500 flight cycles after the effective date of this AD: Do a general visual inspection for any missing, damaged, or incorrectly installed wiper rings in the splined couplings of the flap transmission shafts; and a general visual inspection for any missing, damaged, or incorrectly installed rubber gaiters and straps on the sliding bearing/plunging joints of the flap transmission; in accordance with the Accomplishment Instructions of Airbus Service Bulletin A310-27-2099, dated February 17, 2006. Repeat the inspections thereafter at intervals not to exceed 2,500 flight cycles.

Note 1:

For the purposes of this AD, a general visual inspection is: “A visual examination of an interior or exterior area, installation, or assembly to detect obvious damage, failure, or irregularity. This level of inspection is made from within touching distance unless otherwise specified. A mirror may be necessary to ensure visual access to all surfaces in the inspection area. This level of inspection is made under normally available lighting conditions such as daylight, hangar lighting, flashlight, or droplight and may require removal or opening of access panels or doors. Stands, ladders, or platforms may be required to gain proximity to the area being checked.”

Corrective Actions

(g) If any damaged, missing or incorrectly installed wiper rings, rubber gaiters, or straps are found during any inspection required by paragraph (f) of this AD: Within 400 flight cycles after accomplishing the inspection, replace the applicable component with a serviceable component in accordance with the Accomplishment Instructions of Airbus Service Bulletin A310-27-2099, dated February 17, 2006.

Alternative Methods of Compliance (AMOCs)

(h)(1) The Manager, International Branch, ANM-116, Transport Airplane Directorate, FAA, has the authority to approve AMOCs for this AD, if requested in accordance with the procedures found in 14 CFR 39.19.

(2) Before using any AMOC approved in accordance with § 39.19 on any airplane to which the AMOC applies, notify the appropriate principal inspector in the FAA Flight Standards Certificate Holding District Office.

Related Information

(i) The European Aviation Safety Agency's airworthiness directive 2006-0111, dated May 12, 2006, also addresses the subject of this AD.

Start Signature

Issued in Renton, Washington, on September 22, 2006.

Ali Bahrami,

Manager, Transport Airplane Directorate, Aircraft Certification Service.

End Signature End Part End Supplemental Information

[FR Doc. E6-16204 Filed 10-2-06; 8:45 am]

BILLING CODE 4910-13-P