Occupational Safety and Health Administration (OSHA), Labor.
Request for public comment.
OSHA solicits comments concerning its proposal to extend OMB approval of the information collection requirements contained in the Standard on Mechanical Power Presses (29 CFR 1910.217(e)(1)(i) and (e)(1)(ii)). The purpose of these requirements is to reduce employees' risk of death or serious injury by ensuring that employers maintain the mechanical power presses used by the employees in safe operating condition.
Comments must be submitted (postmarked, sent, or received) by June 5, 2007.
Electronically: You may submit comments and attachments electronically at http://www.regulations.gov, which is the Federal eRulemaking Portal. Follow the instructions online for submitting comments.
Facsimile: If your comments, including attachments, are not longer than 10 pages, you may fax them to the OSHA Docket Office at (202) 693-1648.
Mail, hand delivery, express mail, messenger, or courier service: When using this method, you must submit three copies of your comments and attachments to the OSHA Docket Office, OSHA Docket No. OSHA-2007-0036, U.S. Department of Labor, Occupational Safety and Health Administration, Room N-2625, 200 Constitution Avenue, NW., Washington, DC 20210. Deliveries (hand, express mail, messenger, and courier service) are accepted during the Department of Labor's and Docket Office's normal business hours, 8:15 a.m. to 4:45 p.m., e.t.
Instructions: All submissions must include the Agency name and OSHA docket number for the ICR (OSHA-2007-0036). All comments, including any personal information you provide, are placed in the public docket without change, and may be made available online at http://www.regulations.gov. For further information on submitting comments see the “Public Participation” heading in the section of this notice titled SUPPLEMENTARY INFORMATION.
Docket: To read or download comments or other material in the docket, go to http://www.regulations.gov or the OSHA Docket Office at the address above. All documents in the docket (including this Federal Register notice) are listed in the http://www.regulations.gov index; however, some information (e.g., copyrighted material) is not publicly available to read or download through the Web site. All submissions, including copyrighted material, are available for inspection and copying at the OSHA Docket Office. You may also contact Theda Kenney at the address below to obtain a copy of the ICR.Start Further Info
FOR FURTHER INFORMATION CONTACT:
Theda Kenney or Todd Owen, Directorate of Standards and Guidance, OSHA, U.S. Department of Labor, Room N-3609, 200 Constitution Avenue, NW., Washington, DC 20210; telephone (202) 693-2222.End Further Info End Preamble Start Supplemental Information
The Department of Labor, as part of its continuing effort to reduce paperwork and respondent (i.e., employer) burden, conducts a preclearance consultation program to provide the public with an opportunity to comment on proposed and continuing information collection requirements in accordance with the Paperwork Reduction Act of 1995 (44 U.S.C. 3506(c)(2)(A)). This program ensures that information is in the desired format, reporting burden (time and costs) is minimal, collection instruments are clearly understood, and OSHA's estimate of the information collection burden is accurate. The Occupational Safety and Health Act of 1970 (the OSH Act) (29 U.S.C. 651 et seq.) authorizes information collection by employers as necessary or appropriate for enforcement of the Act or for developing information regarding the causes and prevention of occupational injuries, illnesses, and accidents (29 U.S.C. 657). The OSH Act also requires that OSHA obtain such information with minimum burden upon employers, especially those operating small businesses, and to reduce to the maximum extent feasible unnecessary duplication of efforts in obtaining information (29 U.S.C. 657).
The Standard specifies several paperwork requirements. The following sections describe who uses the information collected under each requirement, as well as how they use it.
Paragraph (e)(1)(i) of § 1910.217 requires employers to establish and follow a program of periodic and regular inspections of power presses to ensure that all their parts, auxiliary equipment, and safeguards are in safe operating condition and adjustment. Employers must maintain a certification record of inspections that includes the date of inspection, the signature of the person who performed the inspection, and the serial number, or other identifier, of the power press that was inspected.
Paragraph (e)(1)(ii) of § 1910.217 requires employers to inspect and test each press no less than weekly to determine the condition of the clutch/brake mechanism, antirepeat feature, and single-stroke mechanism. Employers must perform and complete necessary maintenance or repair or both before the press is operated. In addition, employers must maintain a record of inspections, tests, and maintenance work. The record must include the date of the inspection, test, or maintenance; the signature of the person who performed the inspection, test, or maintenance; and the serial number, or other identifier, of the press that was inspected, tested, or maintained.
The certification records required in 29 CFR 1910.217(e)(1)(i) and (e)(1)(ii) are necessary to ensure compliance with the requirement to inspect mechanical power presses. The inspection of mechanical power presses is critical to ensuring that employers maintain the presses in safe operating condition for employees. These records also provide the most efficient means for the compliance officers to determine that an employer is complying with the Standard.
II. Special Issues for Comment
OSHA has a particular interest in comments on the following issues:
- Whether the proposed information collection requirements are necessary for the proper performance of the Agency's functions, including whether the information is useful;
- The accuracy of OSHA's estimate of the burden (time and costs) of the information collection requirements, including the validity of the methodology and assumptions used;
- The quality, utility, and clarity of the information collected; and
- Ways to minimize the burden on employers who must comply; for example, by using automated or other technological information collection and transmission techniques. Start Printed Page 17195
III. Proposed Actions
OSHA is requesting that OMB extend its approval of the information collection requirements contained in the Standard on Mechanical Power Presses (29 CFR 1910.217(e)(1)(i) and (e)(1)(ii)). The Agency is requesting to retain its existing burden hour estimate associated with this Standard at 1,373,054. The Agency will summarize the comments submitted in response to this notice, and will include this summary in the request to OMB.
Type of Review: Extension of a currently approved collection.
Title: Standard on Mechanical Power Presses (29 CFR 1910.217(e)(1)(i) and (e)(1)(ii)).
OMB Number: 1218-0229.
Affected Public: Business or other for-profit.
Number of Respondents: 295,000.
Frequency: Monthly, weekly.
Average Time per Response: Varies from 2 minutes (.03 hour) to disclose certification records to 20 minutes (.33 hour) to inspect the parts, auxiliary equipment, and safeguards of each mechanical power press.
Total Annual Burden Hours: 1,373,054.
Estimated Cost (Operation and Maintenance): $0.
IV. Public Participation—Submission of Comments on this Notice and Internet Access to Comments and Submissions
You may submit comments in response to this document as follows: (1) Electronically at http://www.regulations.gov, which is the Federal eRulemaking Portal; (2) by facsimile (FAX); or (3) by hard copy. All comments, attachments, and other material must identify the Agency name and the OSHA docket number for the ICR (OSHA Docket No. OSHA-2007-0036). You may supplement electronic submissions by uploading document files electronically. If you wish to mail additional materials in reference to an electronic or facsimile submission, you must submit them to the OSHA Docket Office (see the section of this notice titled ADDRESSES). The additional materials must clearly identify your electronic comments by your name, date, and the docket number so the Agency can attach them to your comments.
Because of security procedures, the use of regular mail may cause a significant delay in the receipt of comments. For information about security procedures concerning the delivery of materials by hand, express delivery, messenger, or courier service, please contact the OSHA Docket Office at (202) 693-2350 (TTY (877) 889-5627).
Comments and submissions are posted without change at http://www.regulations.gov. Therefore, OSHA cautions commenters about submitting personal information such as social security numbers and date of birth. Although all submissions are listed in the http://www.regulations.gov index, some information (e.g., copyrighted material) is not publicly available to read or download through this website. All submissions, including copyrighted material, are available for inspection and copying at the OSHA Docket Office. Information on using the http://www.regulations.gov Web site to submit comments and access the docket is available at the Web site's “User Tips” link. Contact the OSHA Docket Office for information about materials not available through the Web site, and for assistance in using the Internet to locate docket submissions.
Electronic copies of this Federal Register document are available at http://www.regulations.gov. This document as well as news releases and other relevant information also are available at OSHA's Web page at http://www.osha.gov.
V. Authority and Signature
Edwin G. Foulke, Jr., Assistant Secretary of Labor for Occupational Safety and Health, directed the preparation of this notice. The authority for this notice is the Paperwork Reduction Act of 1995 (44 U.S.C. 3506 et seq.) and Secretary of Labor's Order No. 5-2002 (67 FR 65008).Start Signature
Signed at Washington, DC, on April 3, 2007.
Edwin G. Foulke, Jr.,
Assistant Secretary of Labor.
[FR Doc. E7-6434 Filed 4-5-07; 8:45 am]
BILLING CODE 4510-26-P