Skip to Content

Rule

Airworthiness Directives; Bombardier Model DHC-8-102, -103, -106, -201, -202, -301, -311, and -315 Airplanes

Document Details

Information about this document as published in the Federal Register.

Published Document

This document has been published in the Federal Register. Use the PDF linked in the document sidebar for the official electronic format.

Start Preamble Start Printed Page 62559

AGENCY:

Federal Aviation Administration (FAA), Department of Transportation (DOT).

ACTION:

Final rule.

SUMMARY:

We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:

It has been discovered in several cases that clamp bolts of the elevator spring tab mechanism were not installed in the correct orientation. Bolts have been found installed with bolt heads on the lower position and in two cases, some bolts, nuts and washers [hardware] were found to be loose or missing. Detachment of an elevator spring tab mechanism clamp bolt could lead to jamming of the elevator control system and reduced controllability of the aircraft.

We are issuing this AD to require actions to correct the unsafe condition on these products.

DATES:

This AD becomes effective December 11, 2007.

The Director of the Federal Register approved the incorporation by reference of a certain publication listed in this AD as of December 11, 2007.

ADDRESSES:

You may examine the AD docket on the Internet at http://www.regulations.gov or in person at the U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue, SE., Washington, DC.

Start Further Info

FOR FURTHER INFORMATION CONTACT:

Dan Parrillo, Aerospace Engineer, Systems and Flight Test Branch, ANE-172, FAA, New York Aircraft Certification Office, 1600 Stewart Avenue, Suite 410, Westbury, New York 11590; telephone (516) 228-7305; fax (516) 794-5531.

End Further Info End Preamble Start Supplemental Information

SUPPLEMENTARY INFORMATION:

Discussion

We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR part 39 to include an AD that would apply to the specified products. That NPRM was published in the Federal Register on August 31, 2007 (72 FR 50288). That NPRM proposed to correct an unsafe condition for the specified products. The MCAI states:

It has been discovered in several cases that clamp bolts of the elevator spring tab mechanism were not installed in the correct orientation. Bolts have been found installed with bolt heads on the lower position and in two cases, some bolts, nuts and washers [hardware] were found to be loose or missing. Detachment of an elevator spring tab mechanism clamp bolt could lead to jamming of the elevator control system and reduced controllability of the aircraft.

The corrective action is a one-time inspection of the left- and right-hand elevator spring tab mechanism hardware for correct installation, and prior to further flight, installing new hardware for any hardware that is incorrectly installed. You may obtain further information by examining the MCAI in the AD docket.

Comments

We gave the public the opportunity to participate in developing this AD. We received no comments on the NPRM or on the determination of the cost to the public.

Conclusion

We reviewed the available data and determined that air safety and the public interest require adopting the AD as proposed.

Differences Between This AD and the MCAI or Service Information

We have reviewed the MCAI and related service information and, in general, agree with their substance. But we might have found it necessary to use different words from those in the MCAI to ensure the AD is clear for U.S. operators and is enforceable. In making these changes, we do not intend to differ substantively from the information provided in the MCAI and related service information.

We might also have required different actions in this AD from those in the MCAI in order to follow our FAA policies. Any such differences are highlighted in a Note within the AD.

Costs of Compliance

We estimate that this AD will affect about 150 products of U.S. registry. We also estimate that it will take about 3 work-hours per product to comply with the basic requirements of this AD. The average labor rate is $80 per work-hour. Required parts will cost about $0 per product. Where the service information lists required parts costs that are covered under warranty, we have assumed that there will be no charge for these parts. As we do not control warranty coverage for affected parties, some parties may incur costs higher than estimated here. Based on these figures, we estimate the cost of this AD to the U.S. operators to be $36,000, or $240 per product.

Authority for This Rulemaking

Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. “Subtitle VII: Aviation Programs,” describes in more detail the scope of the Agency's authority.

We are issuing this rulemaking under the authority described in “Subtitle VII, Part A, Subpart III, Section 44701: General requirements.” Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.

Regulatory Findings

We determined that this AD will not have federalism implications under Start Printed Page 62560Executive Order 13132. This AD will not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government.

For the reasons discussed above, I certify this AD:

1. Is not a “significant regulatory action” under Executive Order 12866;

2. Is not a “significant rule” under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and

3. Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.

We prepared a regulatory evaluation of the estimated costs to comply with this AD and placed it in the AD docket.

Examining the AD Docket

You may examine the AD docket on the Internet at http://www.regulations.gov; or in person at the Docket Operations office between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains the NPRM, the regulatory evaluation, any comments received, and other information. The street address for the Docket Operations office (telephone (800) 647-5527) is in the ADDRESSES section. Comments will be available in the AD docket shortly after receipt.

Start List of Subjects

List of Subjects in 14 CFR Part 39

End List of Subjects

Adoption of the Amendment

Start Amendment Part

Accordingly, under the authority delegated to me by the Administrator, the FAA amends

End Amendment Part Start Part

PART 39—AIRWORTHINESS DIRECTIVES

End Part Start Amendment Part

1. The authority citation for part 39 continues to read as follows:

End Amendment Part Start Authority

Authority: 49 U.S.C. 106(g), 40113, 44701.

End Authority
[Amended]
Start Amendment Part

2. The FAA amends § 39.13 by adding the following new AD:

End Amendment Part

2007-23-04 Bombardier, Inc. (Formerly de Havilland, Inc.): Amendment 39-15250. Docket No. FAA-2007-29066; Directorate Identifier 2007-NM-147-AD.

Effective Date

(a) This airworthiness directive (AD) becomes effective December 11, 2007.

Affected ADs

(b) None.

Applicability

(c) This AD applies to Bombardier Model DHC-8-102, -103, -106, -201, -202, -301, -311, and -315 airplanes; certificated in any category; serial numbers 003 through 611 inclusive.

Subject

(d) Air Transport Association (ATA) of America Code 27: Flight controls.

Reason

(e) The mandatory continuing airworthiness information (MCAI) states:

It has been discovered in several cases that clamp bolts of the elevator spring tab mechanism were not installed in the correct orientation. Bolts have been found installed with bolt heads on the lower position and in two cases, some bolts, nuts and washers [hardware] were found to be loose or missing. Detachment of an elevator spring tab mechanism clamp bolt could lead to jamming of the elevator control system and reduced controllability of the aircraft.

The corrective action is a one-time inspection of the left- and right-hand elevator spring tab mechanism hardware for correct installation, and prior to further flight, installing new hardware for any hardware that is incorrectly installed.

Actions and Compliance

(f) Unless already done, do the following actions.

(1) Within 12 months after the effective date of this AD: Carry out a one-time inspection of the left- and right-hand elevator spring tab mechanism hardware for correct installation according to the Accomplishment Instructions of Bombardier Service Bulletin 8-27-106, dated February 7, 2006.

(2) If any hardware is found incorrectly installed during the inspection required by paragraph (f)(1) of this AD, prior to further flight, install new hardware according to the Accomplishment Instructions of Bombardier Service Bulletin 8-27-106, dated February 7, 2006.

FAA AD Differences

Note:

This AD differs from the MCAI and/or service information as follows: No differences.

Other FAA AD Provisions

(g) The following provisions also apply to this AD:

(1) Alternative Methods of Compliance (AMOCs): The Manager, New York Aircraft Certification Office, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. Send information to ATTN: Dan Parrillo, Aerospace Engineer, Systems and Flight Test Branch, ANE-172, FAA, New York Aircraft Certification Office, 1600 Stewart Avenue, Suite 410, Westbury, New York 11590; telephone (516) 228-7305; fax (516) 794-5531. Before using any approved AMOC on any airplane to which the AMOC applies, notify your appropriate principal inspector (PI) in the FAA Flight Standards District Office (FSDO), or lacking a PI, your local FSDO.

(2) Airworthy Product: For any requirement in this AD to obtain corrective actions from a manufacturer or other source, use these actions if they are FAA-approved. Corrective actions are considered FAA-approved if they are approved by the State of Design Authority (or their delegated agent). You are required to assure the product is airworthy before it is returned to service.

(3) Reporting Requirements: For any reporting requirement in this AD, under the provisions of the Paperwork Reduction Act, the Office of Management and Budget (OMB) has approved the information collection requirements and has assigned OMB Control Number 2120-0056.

Related Information

(h) Refer to MCAI Canadian Airworthiness Directive CF-2007-08, dated June 4, 2007, and Bombardier Service Bulletin 8-27-106, dated February 7, 2006, for related information.

Material Incorporated by Reference

(i) You must use Bombardier Service Bulletin 8-27-106, dated February 7, 2006, to do the actions required by this AD, unless the AD specifies otherwise.

(1) The Director of the Federal Register approved the incorporation by reference of this service information under 5 U.S.C. 552(a) and 1 CFR part 51.

(2) For service information identified in this AD, contact Bombardier, Inc., Bombardier Regional Aircraft Division, 123 Garratt Boulevard, Downsview, Ontario M3K 1Y5, Canada.

(3) You may review copies at the FAA, Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, Washington; or at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call (202) 741-6030, or go to: http://www.archives.gov/​federal-register/​cfr/​ibr-locations.html.

Start Signature

Issued in Renton, Washington, on October 27, 2007.

Stephen P. Boyd,

Assistant Manager, Transport Airplane Directorate, Aircraft Certification Service.

End Signature End Supplemental Information

[FR Doc. E7-21672 Filed 11-5-07; 8:45 am]

BILLING CODE 4910-13-P