Skip to Content

Proposed Rule

Airworthiness Directives; Pacific Aerospace Limited Model 750XL Airplanes

Document Details

Information about this document as published in the Federal Register.

Published Document

This document has been published in the Federal Register. Use the PDF linked in the document sidebar for the official electronic format.

Start Preamble

AGENCY:

Federal Aviation Administration (FAA), Department of Transportation (DOT).

ACTION:

Notice of proposed rulemaking (NPRM).

SUMMARY:

We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as 1/8-inch rivets installed in place of the correct 5/32-inch rivets that secure the horizontal tail surface load transfer angles to the rearmost fuselage frame at Station 384.62 (Corrected from 369.62 per notification from the Civil Aviation Authority of New Zealand). The proposed AD would require actions that are intended to address the unsafe condition described in the MCAI.

DATES:

We must receive comments on this proposed AD by March 6, 2008.

ADDRESSES:

You may send comments by any of the following methods:

  • Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
  • Fax: (202) 493-2251.
  • Mail: U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue, SE., Washington, DC 20590.
  • Hand Delivery: U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue, SE., Washington, DC 20590, between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays.

Examining the AD Docket

You may examine the AD docket on the Internet at http://www.regulations.gov; or in person at the Docket Management Facility between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this proposed AD, the regulatory evaluation, any comments Start Printed Page 6637received, and other information. The street address for the Docket Office (telephone (800) 647-5527) is in the ADDRESSES section. Comments will be available in the AD docket shortly after receipt.

Start Further Info

FOR FURTHER INFORMATION CONTACT:

Karl Schletzbaum, Aerospace Engineer, FAA, Small Airplane Directorate, 901 Locust, Room 301, Kansas City, Missouri 64106; telephone: (816) 329-4146; fax: (816) 329-4090.

End Further Info End Preamble Start Supplemental Information

SUPPLEMENTARY INFORMATION:

Comments Invited

We invite you to send any written relevant data, views, or arguments about this proposed AD. Send your comments to an address listed under the ADDRESSES section. Include “Docket No. FAA-2008-0136; Directorate Identifier 2007-CE-104-AD” at the beginning of your comments. We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of this proposed AD. We will consider all comments received by the closing date and may amend this proposed AD because of those comments.

We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We will also post a report summarizing each substantive verbal contact we receive about this proposed AD.

Discussion

The Civil Aviation Authority (CAA), which is the airworthiness authority for New Zealand, has issued AD DCA/750XL/4, effective date: September 30, 2004 (referred to after this as “the MCAI”), to correct an unsafe condition for the specified products. The MCAI describes the unsafe condition as 1/8-inch rivets installed in place of the correct 5/32-inch rivets that secure the horizontal tail surface load transfer angles to the rearmost fuselage frame at Station 384.62 (Corrected from 369.62 per notification from the Civil Aviation Authority of New Zealand). The MCAI requires you to inspect for the correct size rivets and if the wrong size rivets are installed, replace the rivets with the correct size rivets.

You may obtain further information by examining the MCAI in the AD docket.

Relevant Service Information

Pacific Aerospace Corporation Limited has issued Mandatory Service Bulletin No. PACSB/XL/010, dated: July 23, 2004. The actions described in this service information are intended to correct the unsafe condition identified in the MCAI.

FAA's Determination and Requirements of the Proposed AD

This product has been approved by the aviation authority of another country, and is approved for operation in the United States. Pursuant to our bilateral agreement with this State of Design Authority, they have notified us of the unsafe condition described in the MCAI and service information referenced above. We are proposing this AD because we evaluated all information and determined the unsafe condition exists and is likely to exist or develop on other products of the same type design.

Differences Between This Proposed AD and the MCAI or Service Information

We have reviewed the MCAI and related service information and, in general, agree with their substance. But we might have found it necessary to use different words from those in the MCAI to ensure the AD is clear for U.S. operators and is enforceable. In making these changes, we do not intend to differ substantively from the information provided in the MCAI and related service information.

Costs of Compliance

Based on the service information, we estimate that this proposed AD would affect about 7 products of U.S. registry. We also estimate that it would take about .5 work-hour per product to comply with the basic requirements of this proposed AD. The average labor rate is $80 per work-hour.

Based on these figures, we estimate the cost of the proposed AD on U.S. operators to be $280, or $40 per product.

In addition, we estimate that any necessary follow-on actions would take about 2 work-hours and require parts costing $10, for a cost of $170 per product. We have no way of determining the number of products that may need these actions.

Authority for This Rulemaking

Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. “Subtitle VII: Aviation Programs,” describes in more detail the scope of the Agency's authority.

We are issuing this rulemaking under the authority described in “Subtitle VII, Part A, Subpart III, Section 44701: General requirements.” Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.

Regulatory Findings

We determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government.

For the reasons discussed above, I certify this proposed regulation:

1. Is not a “significant regulatory action” under Executive Order 12866;

2. Is not a “significant rule” under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and

3. Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.

We prepared a regulatory evaluation of the estimated costs to comply with this proposed AD and placed it in the AD docket.

Start List of Subjects

List of Subjects in 14 CFR Part 39

End List of Subjects

The Proposed Amendment

Accordingly, under the authority delegated to me by the Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

Start Part

PART 39—AIRWORTHINESS DIRECTIVES

1. The authority citation for part 39 continues to read as follows:

Start Authority

Authority: 49 U.S.C. 106(g), 40113, 44701.

End Authority
[Amended]

2. The FAA amends § 39.13 by adding the following new AD:

Pacific Aerospace Limited: Docket No. FAA-2008-0136; Directorate Identifier 2007-CE-104-AD.

Comments Due Date

(a) We must receive comments by March 6, 2008.

Affected ADs

(b) None. Start Printed Page 6638

Applicability

(c) This AD applies to 750XL airplanes, serial numbers 101 through 108, certificated in any category.

Subject

(d) Air Transport Association of America (ATA) Code 51: Structures.

Reason

(e) The MCAI describes the unsafe condition as 1/8-inch rivets installed in place of the correct 5/32-inch rivets that secure the horizontal tail surface load transfer angles to the rearmost fuselage frame at Station 384.62 (Corrected from 369.62 per notification from the Civil Aviation Authority of New Zealand). The MCAI requires you to inspect for the correct size rivets and if the wrong size rivets are installed, replace the rivets with the correct size rivets.

Actions and Compliance

(f) Unless already done, do the following actions:

(1) Within 100 hours time-in-service (TIS) after the effective date of this AD, inspect to ensure that 1/8-inch rivets are not installed in place of the correct 5/32-inch rivets that secure the horizontal tail surface load transfer angles to the rearmost fuselage frame at Station 384.62 following Pacific Aerospace Corporation Limited Mandatory Service Bulletin No. PACSB/XL/010, dated: July 23, 2004.

(2) Before further flight, if you find undersized rivets are installed as a result of the inspection required by paragraph (f)(1) of this AD, replace the undersized rivets with the correct 5/32-inch rivets following Pacific Aerospace Corporation Limited Service Mandatory Bulletin No. PACSB/XL/010, dated: July 23, 2004.

FAA AD Differences

Note:

This AD differs from the MCAI and/or service information as follows: An official of The New Zealand Civil Aviation Authority confirms that the MCAI should reference Station 384.62.

Other FAA AD Provisions

(g) The following provisions also apply to this AD:

(1) Alternative Methods of Compliance (AMOCs): The Manager, Standards Office, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. Send information to ATTN: Karl Schletzbaum, Aerospace Engineer, FAA, Small Airplane Directorate, 901 Locust, Room 301, Kansas City, Missouri 64106; telephone: (816) 329-4146; fax: (816) 329-4090. Before using any approved AMOC on any airplane to which the AMOC applies, notify your appropriate principal inspector (PI) in the FAA Flight Standards District Office (FSDO), or lacking a PI, your local FSDO.

(2) Airworthy Product: For any requirement in this AD to obtain corrective actions from a manufacturer or other source, use these actions if they are FAA-approved. Corrective actions are considered FAA-approved if they are approved by the State of Design Authority (or their delegated agent). You are required to assure the product is airworthy before it is returned to service.

(3) Reporting Requirements: For any reporting requirement in this AD, under the provisions of the Paperwork Reduction Act (44 U.S.C. 3501 et. seq.), the Office of Management and Budget (OMB) has approved the information collection requirements and has assigned OMB Control Number 2120-0056.

Related Information

(h) Refer to MCAI Civil Aviation Authority of New Zealand AD DCA/750XL/4, effective date: September 30, 2004; and Pacific Aerospace Corporation Limited Mandatory Service Bulletin No. PACSB/XL/010, dated: July 23, 2004, for related information.

Start Signature

Issued in Kansas City, Missouri, on January 29, 2008.

John Colomy,

Acting Manager, Small Airplane Directorate, Aircraft Certification Service.

End Signature End Part End Supplemental Information

[FR Doc. E8-2046 Filed 2-4-08; 8:45 am]

BILLING CODE 4910-13-P