This site displays a prototype of a “Web 2.0” version of the daily Federal Register. It is not an official legal edition of the Federal Register, and does not replace the official print version or the official electronic version on GPO’s govinfo.gov.
The documents posted on this site are XML renditions of published Federal Register documents. Each document posted on the site includes a link to the corresponding official PDF file on govinfo.gov. This prototype edition of the daily Federal Register on FederalRegister.gov will remain an unofficial informational resource until the Administrative Committee of the Federal Register (ACFR) issues a regulation granting it official legal status. For complete information about, and access to, our official publications and services, go to About the Federal Register on NARA's archives.gov.
The OFR/GPO partnership is committed to presenting accurate and reliable regulatory information on FederalRegister.gov with the objective of establishing the XML-based Federal Register as an ACFR-sanctioned publication in the future. While every effort has been made to ensure that the material on FederalRegister.gov is accurately displayed, consistent with the official SGML-based PDF version on govinfo.gov, those relying on it for legal research should verify their results against an official edition of the Federal Register. Until the ACFR grants it official status, the XML rendition of the daily Federal Register on FederalRegister.gov does not provide legal notice to the public or judicial notice to the courts.
Federal Aviation Administration (FAA), Department of Transportation (DOT).
Final rule; request for comments.
We are adopting a new airworthiness directive (AD) for the products listed above that would revise an existing AD. This AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:Start Printed Page 52878
Subsequent to accidents involving Fuel Tank System explosions in flight * * * and on ground, * * * Special Federal Aviation Regulation 88 (SFAR88) * * * required a safety review of the aircraft Fuel Tank System * * *.
Fuel Airworthiness Limitations are items arising from a systems safety analysis that have been shown to have failure mode(s) associated with an `unsafe condition' * * *. These are identified in Failure Conditions for which an unacceptable probability of ignition risk could exist if specific tasks and/or practices are not performed in accordance with the manufacturers' requirements.
This AD requires actions that are intended to address the unsafe condition described in the MCAI.
This AD becomes effective October 30, 2009.
On December 11, 2007 (72 FR 62564, November 6, 2007), the Director of the Federal Register approved the incorporation by reference of certain publications listed in the AD.
We must receive comments on this AD by November 30, 2009.
You may send comments by any of the following methods:
Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
- Fax: (202) 493-2251.
- Mail: U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue, SE., Washington, DC 20590.
- Hand Delivery: U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-40, 1200 New Jersey Avenue, SE., Washington, DC, between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays.
For service information identified in this AD, contact Saab Aircraft AB, SAAB Aerosystems, SE 581 88, Linköping, Sweden; telephone +46 13 18 5591; fax +46 13 18 4874; e-mail email@example.com; Internet http://www.saabgroup.com.
Examining the AD Docket
You may examine the AD docket on the Internet at http://www.regulations.gov; or in person at the Docket Operations office between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this AD, the regulatory evaluation, any comments received, and other information. The street address for the Docket Operations office (telephone (800) 647-5527) is in the ADDRESSES section. Comments will be available in the AD docket shortly after receipt.Start Further Info
FOR FURTHER INFORMATION CONTACT:
Shahram Daneshmandi, Aerospace Engineer, International Branch, ANM-116, Transport Airplane Directorate, FAA, 1601 Lind Avenue, SW., Renton, Washington 98057-3356; telephone (425) 227-1112; fax (425) 227-1149.End Further Info End Preamble Start Supplemental Information
On October 27, 2007, we issued AD 2007-23-05, Amendment 39-15251 (72 FR 62564, November 6, 2007). That AD applied to all Saab Model SAAB 2000 airplanes. That AD required revising the Airworthiness Limitations Section (ALS) of the Instructions for Continued Airworthiness.
Critical design configuration control limitations (CDCCLs) are limitation requirements to preserve a critical ignition source prevention feature of the fuel tank system design that is necessary to prevent the occurrence of an unsafe condition. The purpose of a CDCCL is to provide instruction to retain the critical ignition source prevention feature during configuration change that may be caused by alterations, repairs, or maintenance actions. A CDCCL is not a periodic inspection.
Since we issued that AD, we have determined that it is necessary to clarify the AD's intended effect on spare and on-airplane fuel tank system components, regarding the use of maintenance manuals and instructions for continued airworthiness.
Section 91.403(c) of the Federal Aviation Regulations (14 CFR 91.403(c)) specifies the following:
No person may operate an aircraft for which a manufacturer's maintenance manual or instructions for continued airworthiness has been issued that contains an airworthiness limitation section unless the mandatory * * * procedures * * * have been complied with.
Some operators have questioned whether existing components affected by the new CDCCLs must be reworked. We did not intend for the AD to retroactively require rework of components that had been maintained using acceptable methods before the effective date of the AD. Owners and operators of the affected airplanes therefore are not required to rework affected components identified as airworthy or installed on the affected airplanes before the required revisions of the ALS. But once the CDCCLs are incorporated into the ALS, future maintenance actions on components must be done in accordance with those CDCCLs.
This product has been approved by the aviation authority of another country, and is approved for operation in the United States.
Differences Between the AD and the MCAI or Service Information
We have reviewed the MCAI and related service information and, in general, agree with their substance. But we might have found it necessary to use different words from those in the MCAI to ensure the AD is clear for U.S. operators and is enforceable. In making these changes, we do not intend to differ substantively from the information provided in the MCAI and related service information.
We might also have required different actions in this AD from those in the MCAI in order to follow FAA policies. Any such differences are highlighted in a note within the AD.
FAA's Justification and Determination of the Effective Date
This revision merely clarifies the intended effect on spare and on-airplane fuel tank system components, and makes no substantive change to the AD's requirements. For this reason, it is found that notice and opportunity for prior public comment for this action are unnecessary, and good cause exists for making this amendment effective in less than 30 days.
This AD is a final rule that involves requirements affecting flight safety, and we did not precede it by notice and opportunity for public comment. We invite you to send any written relevant data, views, or arguments about this AD. Send your comments to an address listed under the ADDRESSES section. Include “Docket No. FAA-2009-0909; Directorate Identifier 2009-NM-172-AD” at the beginning of your comments. We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of this AD. We will consider all comments received by the closing date and may amend this AD because of those comments.
We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We will also post a report summarizing each substantive verbal contact we receive about this AD.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. “Subtitle VII: Aviation Programs,” describes in more Start Printed Page 52879detail the scope of the Agency's authority.
We are issuing this rulemaking under the authority described in “Subtitle VII, Part A, Subpart III, Section 44701: General requirements.” Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.
We determined that this AD will not have federalism implications under Executive Order 13132. This AD will not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government.
For the reasons discussed above, I certify this AD:
1. Is not a “significant regulatory action” under Executive Order 12866;
2. Is not a “significant rule” under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and
3. Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.
We prepared a regulatory evaluation of the estimated costs to comply with this AD and placed it in the AD docket.Start List of Subjects
List of Subjects in 14 CFR Part 39End List of Subjects
Adoption of the AmendmentStart Amendment Part
Accordingly, under the authority delegated to me by the Administrator, the FAA amendsEnd Amendment Part Start Part
PART 39—AIRWORTHINESS DIRECTIVESEnd Part Start Amendment Part
1. The authority citation for part 39 continues to read as follows:End Amendment Part
2. The FAA amends § 39.13 by removing amendment 39-15251 (End Amendment Part
2007-23-05 R1 Saab AB, Saab Aerosystems: Amendment 39-16045. Docket No. FAA-2009-0909; Directorate Identifier 2009-NM-172-AD.
(a) This airworthiness directive (AD) becomes effective October 30, 2009.
(b) This AD revises AD 2007-23-05.
(c) This AD applies to all Saab AB, Saab Aerosystems Model SAAB 2000 airplanes, certificated in any category, all serial numbers.
This AD requires revisions to certain operator maintenance documents to include new inspections. Compliance with these inspections is required by 14 CFR 91.403(c). For airplanes that have been previously modified, altered, or repaired in the areas addressed by these inspections, the operator may not be able to accomplish the inspections described in the revisions. In this situation, to comply with 14 CFR 91.403(c), the operator must request approval for an alternative method of compliance according to paragraph (g) of this AD. The request should include a description of changes to the required inspections that will ensure the continued operational safety of the airplane.
(d) Air Transport Association (ATA) of America Code 28: Fuel.
(e) The mandatory continuing airworthiness information (MCAI) states:
Subsequent to accidents involving Fuel Tank System explosions in flight * * * and on ground, the FAA published Special Federal Aviation Regulation 88 (SFAR 88) in June 2001. SFAR 88 required a safety review of the aircraft Fuel Tank System to determine that the design meets the requirements of FAR (Federal Aviation Regulation) § 25.901 and § 25.981(a) and (b).
A similar regulation has been recommended by the JAA (Joint Aviation Authorities) to the European National Aviation Authorities in JAA letter 04/00/02/07/03-L024 of 3 February 2003. The review was requested to be mandated by NAA's (National Aviation Authorities) using JAR (Joint Aviation Regulation) § 25.901(c), § 25.1309.
In August 2005 EASA (European Aviation Safety Agency) published a policy statement on the process for developing instructions for maintenance and inspection of Fuel Tank System ignition source prevention (EASA D 2005/CPRO, www.easa.eu.int/home/cert_policy_statements_en.html) that also included the EASA expectations with regard to compliance times of the corrective actions on the unsafe and the not unsafe part of the harmonised design review results. On a global scale the TC (type certificate) holders committed themselves to the EASA published compliance dates (see EASA policy statement). The EASA policy statement has been revised in March 2006: the date of 31-12-2005 for the unsafe related actions has now been set at 01-07-2006.
Fuel Airworthiness Limitations are items arising from a systems safety analysis that have been shown to have failure mode(s) associated with an `unsafe condition' as defined in FAA's memo 2003-112-15 `SFAR 88—Mandatory Action Decision Criteria'. These are identified in Failure Conditions for which an unacceptable probability of ignition risk could exist if specific tasks and/or practices are not performed in accordance with the manufacturers' requirements.
This EASA Airworthiness Directive mandates the Fuel System Airworthiness Limitations (comprising maintenance/inspection tasks and Critical Design Configuration Control Limitations (CDCCL)) for the type of aircraft, that resulted from the design reviews and the JAA recommendation and EASA policy statement mentioned above.
The corrective action is revising the Airworthiness Limitations Section (ALS) of the Instructions for Continued Airworthiness to incorporate new limitations for fuel tank systems.
Restatement of AD 2007-23-05, With No Changes
Actions and Compliance
(f) Unless already done, do the following actions.
(1) Within 3 months after December 11, 2007 (the effective date of AD 2007-23-05), revise the ALS of the Instructions for Continued Airworthiness to incorporate the maintenance and inspection instructions in Part 1 of Saab Fuel Airworthiness Limitations 2000 LKS 009032, dated February 14, 2006. For all tasks identified in Part 1 of Saab Fuel Airworthiness Limitations 2000 LKS 009032, dated February 14, 2006, the initial compliance times start from December 11, 2007, and the repetitive inspections must be accomplished thereafter at the interval specified in Part 1 of Saab Fuel Airworthiness Limitations 2000 LKS 009032, dated February 14, 2006.
(2) Within 12 months after December 11, 2007, revise the ALS of the Instructions for Continued Airworthiness to incorporate the CDCCLs as defined in Part 2 of Saab Fuel Airworthiness Limitations 2000 LKS 009032, dated February 14, 2006.
(3) Except as provided by paragraph (g) of this AD: After accomplishing the actions specified in paragraphs (f)(1) and (f)(2) of this AD, no alternative inspection, inspection intervals, or CDCCLs may be used.
(4) Where Saab Fuel Airworthiness Limitations 2000 LKS 009032, dated February 14, 2006, allows for exceptional short-term extensions, an exception is acceptable to the FAA if it is approved by the appropriate principal inspector in the FAA Flight Standards Certificate Holding District Office.
Explanation of CDCCL Requirements
Notwithstanding any other maintenance or operational requirements, components that have been identified as airworthy or installed on the affected airplanes before the revision of the airworthiness limitations section (ALS), as required by paragraph (f) of this AD, do not need to be reworked in accordance with the Start Printed Page 52880CDCCLs. However, once the airworthiness limitations section has been revised, future maintenance actions on these components must be done in accordance with the CDCCLs.
FAA AD Differences
This AD differs from the MCAI and/or service information as follows: No differences.
Other FAA AD Provisions
(g) The following provisions also apply to this AD:
(1) Alternative Methods of Compliance (AMOCs): The Manager, International Branch, ANM-116, Transport Airplane Directorate, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. Send information to ATTN: Shahram Daneshmandi, Aerospace Engineer, International Branch, ANM-116, Transport Airplane Directorate, FAA, 1601 Lind Avenue, SW., Renton, Washington 98057-3356; telephone (425) 227-1112; fax (425) 227-1149. Before using any approved AMOC on any airplane to which the AMOC applies, notify your principal maintenance inspector (PMI) or principal avionics inspector (PAI), as appropriate, or lacking a principal inspector, your local Flight Standards District Office. The AMOC approval letter must specifically reference this AD.
(2) Airworthy Product: For any requirement in this AD to obtain corrective actions from a manufacturer or other source, use these actions if they are FAA-approved. Corrective actions are considered FAA-approved if they are approved by the State of Design Authority (or their delegated agent). You are required to assure the product is airworthy before it is returned to service.
(3) Reporting Requirements: For any reporting requirement in this AD, under the provisions of the Paperwork Reduction Act, the Office of Management and Budget (OMB) has approved the information collection requirements and has assigned OMB Control Number 2120-0056.
(h) Refer to MCAI European Aviation Safety Agency Airworthiness Directive 2006-0199, dated July 11, 2006; and Saab Fuel Airworthiness Limitations 2000 LKS 009032, dated February 14, 2006; for related information.
Material Incorporated by Reference
(i) You must use Saab Fuel Airworthiness Limitations 2000 LKS 009032, dated February 14, 2006, to do the actions required by this AD, unless the AD specifies otherwise.
(1) The Director of the Federal Register previously approved the incorporation by reference of this service information on December 11, 2007 (72 FR 62564, November 6, 2007).
(2) For service information identified in this AD, contact Saab Aircraft AB, SAAB Aerosystems, SE 581 88, Linköping, Sweden; telephone +46 13 18 5591; fax +46 13 18 4874; e-mail firstname.lastname@example.org; Internet http://www.saabgroup.com.
(3) You may review copies of the service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, Washington. For information on the availability of this material at the FAA, call 425-227-1221 or 425-227-1152.
(4) You may also review copies of the service information that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html.Start Signature
Issued in Renton, Washington, on September 18, 2009.
Manager, Transport Airplane Directorate, Aircraft Certification Service.
[FR Doc. E9-24542 Filed 10-14-09; 8:45 am]
BILLING CODE 4910-13-P