Skip to Content

Proposed Rule

Airworthiness Directives; Bombardier, Inc. Model CL-600-2B19 (Regional Jet Series 100 & 440) Airplanes

Document Details

Information about this document as published in the Federal Register.

Published Document

This document has been published in the Federal Register. Use the PDF linked in the document sidebar for the official electronic format.

Start Preamble

AGENCY:

Federal Aviation Administration (FAA), DOT.

ACTION:

Notice of proposed rulemaking (NPRM).

SUMMARY:

We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as: There have been several Stick Pusher Capstan Shaft failures causing severe degradation of the stick pusher function. This directive is issued to revise the first flight of the day check of the stall protection system to detect degradation of the stick pusher function. It also introduces a new repetitive maintenance task to limit exposure to dormant failure of the stick pusher capstan shaft. Dormant loss or severe degradation of the stick pusher function could result in reduced controllability of the airplane. The proposed AD would require actions that are intended to address the unsafe condition described in the MCAI.

DATES:

We must receive comments on this proposed AD by July 19, 2010.

ADDRESSES:

You may send comments by any of the following methods:

  • Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.
  • Fax: (202) 493-2251.
  • Mail: U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room Start Printed Page 31325W12-140, 1200 New Jersey Avenue, SE., Washington, DC 20590.
  • Hand Delivery: U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-40, 1200 New Jersey Avenue SE., Washington, DC, between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays.

For service information identified in this proposed AD, contact Bombardier, Inc., 400 Côte-Vertu Road West, Dorval, Québec H4S 1Y9, Canada; telephone 514-855-5000; fax 514-855-7401; e-mail thd.crj@aero.bombardier.com; Internet http://www.bombardier.com. You may review copies of the referenced service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, Washington. For information on the availability of this material at the FAA, call 425-227-1221 or 425-227-1152.

Examining the AD Docket

You may examine the AD docket on the Internet at http://www.regulations.gov;​ or in person at the Docket Operations office between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this proposed AD, the regulatory evaluation, any comments received, and other information. The street address for the Docket Operations office (telephone (800) 647-5527) is in the ADDRESSES section. Comments will be available in the AD docket shortly after receipt.

Start Further Info

FOR FURTHER INFORMATION CONTACT:

Bruce Valentine, Avionics and Flight Test Branch, ANE-172, FAA, New York Aircraft Certification Office (ACO), 1600 Stewart Avenue, Suite 410, Westbury, New York 11590; telephone (516) 228-7328; fax (516) 794-5531.

End Further Info End Preamble Start Supplemental Information

SUPPLEMENTARY INFORMATION:

Comments Invited

We invite you to send any written relevant data, views, or arguments about this proposed AD. Send your comments to an address listed under the ADDRESSES section. Include “Docket No. FAA-2010-0482; Directorate Identifier 2009-NM-225-AD” at the beginning of your comments. We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of this proposed AD. We will consider all comments received by the closing date and may amend this proposed AD based on those comments.

We have lengthened the 30-day comment period for proposed ADs that address MCAI originated by aviation authorities of other countries to provide adequate time for interested parties to submit comments. The comment period for these proposed ADs is now typically 45 days, which is consistent with the comment period for domestic transport ADs.

We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We will also post a report summarizing each substantive verbal contact we receive about this proposed AD.

Discussion

Transport Canada Civil Aviation, which is the aviation authority for Canada, has issued Canadian Airworthiness Directive CF-2009-36, dated September 2, 2009 (referred to after this as “the MCAI”), to correct an unsafe condition for the specified products. The MCAI states:

There have been several Stick Pusher Capstan Shaft failures causing severe degradation of the stick pusher function. This directive is issued to revise the first flight of the day check of the stall protection system to detect degradation of the stick pusher function. It also introduces a new repetitive maintenance task to limit exposure to dormant failure of the stick pusher capstan shaft.

Dormant loss or severe degradation of the stick pusher function could result in reduced controllability of the airplane. You may obtain further information by examining the MCAI in the AD docket.

Relevant Service Information

Bombardier has issued Temporary Revision (TR) 2A-43, dated May 7, 2008, to Appendix A—Certification Maintenance Requirements of Part 2 of the Bombardier CL-600-2B19 Maintenance Requirements Manual; and Canadair Regional Jet TR RJ/178-1, dated March 8, 2010, to Canadair Regional Jet Airplane Flight Manual CSP A-012. The actions described in this service information are intended to correct the unsafe condition identified in the MCAI.

FAA's Determination and Requirements of This Proposed AD

This product has been approved by the aviation authority of another country, and is approved for operation in the United States. Pursuant to our bilateral agreement with the State of Design Authority, we have been notified of the unsafe condition described in the MCAI and service information referenced above. We are proposing this AD because we evaluated all pertinent information and determined an unsafe condition exists and is likely to exist or develop on other products of the same type design.

Differences Between This AD and the MCAI or Service Information

We have reviewed the MCAI and related service information and, in general, agree with their substance. But we might have found it necessary to use different words from those in the MCAI to ensure the AD is clear for U.S. operators and is enforceable. In making these changes, we do not intend to differ substantively from the information provided in the MCAI and related service information.

We might also have proposed different actions in this AD from those in the MCAI in order to follow FAA policies. Any such differences are highlighted in a Note within the proposed AD.

Costs of Compliance

Based on the service information, we estimate that this proposed AD would affect about 601 products of U.S. registry. We also estimate that it would take about 1 work-hour per product to comply with the basic requirements of this proposed AD. The average labor rate is $85 per work-hour. Based on these figures, we estimate the cost of the proposed AD on U.S. operators to be $51,085, or $85 per product.

Authority for This Rulemaking

Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. “Subtitle VII: Aviation Programs,” describes in more detail the scope of the Agency's authority.

We are issuing this rulemaking under the authority described in “Subtitle VII, Part A, Subpart III, Section 44701: General requirements.” Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.

Regulatory Findings

We determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government.Start Printed Page 31326

For the reasons discussed above, I certify this proposed regulation:

1. Is not a “significant regulatory action” under Executive Order 12866;

2. Is not a “significant rule” under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and

3. Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.

We prepared a regulatory evaluation of the estimated costs to comply with this proposed AD and placed it in the AD docket.

Start List of Subjects

List of Subjects in 14 CFR Part 39

End List of Subjects

The Proposed Amendment

Accordingly, under the authority delegated to me by the Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

Start Part

PART 39—AIRWORTHINESS DIRECTIVES

1. The authority citation for part 39 continues to read as follows:

Start Authority

Authority: 49 U.S.C. 106(g), 40113, 44701.

End Authority
[Amended]

2. The FAA amends § 39.13 by adding the following new AD:

Bombardier, Inc.: Docket No. FAA-2010-0482; Directorate Identifier 2009-NM-225-AD.

Comments Due Date

(a) We must receive comments by July 19, 2010.

Affected ADs

(b) None.

Applicability

(c) This AD applies to Bombardier, Inc. Model CL-600-2B19 (Regional Jet Series 100 & 440) airplanes, certificated in any category, serial numbers 7003 through 7990 inclusive, and 8000 and subsequent.

Note 1:

This AD requires revisions to certain operator maintenance documents to include new inspections. Compliance with these inspections is required by 14 CFR 91.403(c). For airplanes that have been previously modified, altered, or repaired in the areas addressed by these inspections, the operator may not be able to accomplish the inspections described in the revisions. In this situation, to comply with 14 CFR 91.403(c), the operator must request approval for an alternative method of compliance according to paragraph (h)(1) of this AD. The request should include a description of changes to the required inspections that will ensure the continued operational safety of the airplane.

Subject

(d) Air Transport Association (ATA) of America Code 27: Flight controls.

Reason

(e) The mandatory continuing airworthiness information (MCAI) states:

There have been several Stick Pusher Capstan Shaft failures causing severe degradation of the stick pusher function. This directive is issued to revise the first flight of the day check of the stall protection system to detect degradation of the stick pusher function. It also introduces a new repetitive maintenance task to limit exposure to dormant failure of the stick pusher capstan shaft.

Dormant loss or severe degradation of the stick pusher function could result in reduced controllability of the airplane.

Compliance

(f) You are responsible for having the actions required by this AD performed within the compliance times specified, unless the actions have already been done.

Actions

(g) Do the following actions.

(1) Within 30 days after the effective date of this AD, revise the Limitations section of Canadair Regional Jet Airplane Flight Manual (AFM) CSP A-012 to include the information in Canadair Regional Jet Temporary Revision (TR) RJ/178-1, dated March 8, 2010; as specified in the TR. The Canadair Regional Jet TR RJ/178-1, dated March 8, 2010, introduces procedures for performing a stall protection system test. Operate the airplane according to the limitations and procedures in the Canadair Regional Jet TR RJ/178-1, dated March 8, 2010.

Note 2:

This may be done by inserting a copy of Canadair Regional Jet TR RJ/178-1, dated March 8, 2010, into the Canadair Regional Jet AFM CSP A-012. When this Canadair Regional Jet TR has been included in general revisions of the Canadair Regional Jet AFM, the general revisions may be inserted in the AFM, provided the relevant information in the general revision is identical to that in the Canadair Regional Jet TR.

(2) Within 30 days after the effective date of this AD, revise Appendix A—Certification Maintenance Requirements of Part 2 of the Bombardier CL-600-2B19 Maintenance Requirements Manual (MRM) by incorporating the information in Bombardier TR 2A-43, dated May 7, 2008; as specified in the TR. The initial compliance time for the new MRM task identified in the TR is at the later of the times specified in paragraphs (g)(2)(i) and (g)(2)(ii) of this AD. Thereafter, except as provided by paragraph (h)(1) of this AD, no alternative task intervals may be used. The TR to the MRM introduces procedures for a function check of the stick pusher capstan.

(i) Prior to the accumulation of 5,000 total flight hours.

(ii) Within 500 flight hours after the effective date of this AD.

Note 3:

The actions required by paragraph (g)(2) of this AD may be done by inserting a copy of Bombardier TR 2A-43, dated May 7, 2008, to Appendix A—Certification Maintenance Requirements of Part 2 of the Bombardier CL-600-2B19 MRM. When this Bombardier TR has been included in general revisions of the Bombardier MRM, the Bombardier TR may be removed from the MRM, provided the relevant information in the general revision is identical to that in Bombardier TR 2A-43, dated May 7, 2008.

FAA AD Differences

Note 4:

This AD differs from the MCAI and/or service information as follows: No differences.

Other FAA AD Provisions

(h) The following provisions also apply to this AD:

(1) Alternative Methods of Compliance (AMOCs): The Manager, New York Aircraft Certification Office, ANE-170, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. Send information to Attn: Program Manager, Continuing Operational Safety, FAA, New York ACO, 1600 Stewart Avenue, Suite 410, Westbury, New York, 11590; telephone 516-228-7300; fax 516-794-5531. Before using any approved AMOC on any airplane to which the AMOC applies, notify your principal maintenance inspector (PMI) or principal avionics inspector (PAI), as appropriate, or lacking a principal inspector, your local Flight Standards District Office. The AMOC approval letter must specifically reference this AD.

(2) Airworthy Product: For any requirement in this AD to obtain corrective actions from a manufacturer or other source, use these actions if they are FAA-approved. Corrective actions are considered FAA-approved if they are approved by the State of Design Authority (or their delegated agent). You are required to assure the product is airworthy before it is returned to service.

(3) Reporting Requirements: For any reporting requirement in this AD, under the provisions of the Paperwork Reduction Act (44 U.S.C. 3501 et seq.), the Office of Management and Budget (OMB) has approved the information collection requirements and has assigned OMB Control Number 2120-0056.

(4) Special Flight Permits: We are not allowing special flight permits, as described in Section 21.197 and Section 21.199 of the Federal Aviation Regulations (14 CFR 21.197 and 21.199).

Related Information

(i) Refer to MCAI Canadian Airworthiness Directive CF-2009-36, dated September 2, 2009; and Bombardier TR 2A-43, dated May 7, 2008, to Appendix A—Certification Maintenance Requirements of Part 2 of the Bombardier CL-600-2B19 Maintenance Requirements Manual, dated May 7, 2008; and Canadair Regional Jet TR RJ/178-1, dated March 8, 2010, to Canadair Regional Jet Airplane Flight Manual CSP A-012; for related information.

Start Signature
Start Printed Page 31327

Issued in Renton, Washington, on May 25, 2010.

Ali Bahrami,

Manager, Transport Airplane Directorate, Aircraft Certification Service.

End Signature End Part End Supplemental Information

[FR Doc. 2010-13305 Filed 6-2-10; 8:45 am]

BILLING CODE 4910-13-P