This PDF is the current document as it appeared on Public Inspection on 06/20/2017 at 08:45 am.
Occupational Safety and Health Administration (OSHA), Labor.
In this notice, OSHA announces its final decision to expand the scope of recognition for SGS North America, Inc., as a Nationally Recognized Testing Laboratory (NRTL).
The expansion of the scope of recognition becomes effective on June 21, 2017.Start Further Info
FOR FURTHER INFORMATION CONTACT:
Information regarding this notice is available from the following sources:
Press inquiries: Contact Mr. Frank Meilinger, Director, OSHA Office of Communications, U.S. Department of Labor, 200 Constitution Avenue NW., Room N-3647, Washington, DC 20210; telephone: (202) 693-1999; email: email@example.com.
General and technical information: Contact Mr. Kevin Robinson, Director, Office of Technical Programs and Coordination Activities, Directorate of Technical Support and Emergency Management, Occupational Safety and Health Administration, U.S. Department of Labor, 200 Constitution Avenue NW., Room N-3655, Washington, DC 20210; telephone: (202) 693-2110; email: firstname.lastname@example.org. OSHA's Web page includes information about the NRTL Program (see http://www.osha.gov/dts/otpca/nrtl/index.html).End Further Info End Preamble Start Supplemental Information
I. Notice of Final Decision
OSHA hereby gives notice of the expansion of the scope of recognition of SGS North America, Inc. (SGS), as an NRTL. SGS's expansion covers the addition of two test standards to its scope of recognition.
OSHA recognition of an NRTL signifies that the organization meets the requirements specified by 29 CFR 1910.7. Recognition is an acknowledgment that the organization can perform independent safety testing and certification of the specific products covered within its scope of recognition and is not a delegation or grant of government authority. As a result of recognition, employers may use products properly approved by the NRTL to meet OSHA standards that require testing and certification of the products.
The Agency processes applications by an NRTL for initial recognition, or for expansion or renewal of this recognition, following requirements in Appendix A to 29 CFR 1910.7. This appendix requires that the Agency publish two notices in the Federal Register in processing an application. In the first notice, OSHA announces the application and provides its preliminary finding and, in the second notice, the Agency provides its final decision on the application. These notices set forth the NRTL's scope of recognition or modifications of that scope. OSHA maintains an informational Web page for each NRTL that details its scope of recognition. These pages are available from the Agency's Web site at http://www.osha.gov/dts/otpca/nrtl/index.html.
SGS submitted an application, dated May 28, 2014, (OSHA-2006-0040-0034) to expand its recognition to include two additional test standards. OSHA staff detailed analysis of the application packet and reviewed other pertinent information. OSHA did not perform any on-site reviews in relation to this application.
OSHA published the preliminary notice announcing SGS's expansion application in the Federal Register on March 15, 2017 (82 FR 13867). The Agency requested comments by March 30, 2017, but it received no comments in response to this notice. OSHA now is proceeding with this final notice to grant expansion of SGS's scope of recognition.
To obtain or review copies of all public documents pertaining to the SGS's application, go to www.regulations.gov or contact the Docket Office, Occupational Safety and Health Administration, U.S. Department of Labor, 200 Constitution Avenue NW., Room N-2625, Washington, DC 20210. Docket No. OSHA-2006-0040 contains all materials in the record concerning SGS's recognition.
II. Final Decision and Order
OSHA staff examined SGS's expansion application, its capability to meet the requirements of the test standards, and other pertinent information. Based on its review of this evidence, OSHA finds that SGS meets the requirements of 29 CFR 1910.7 for expansion of its recognition, subject to the limitation and conditions listed below. OSHA, therefore, is proceeding with this final notice to grant SGS's scope of recognition. OSHA limits the expansion of SGS's recognition to testing and certification of products for demonstration of conformance to the test standards listed in Table 1 below.
|Test standard||Test standard title|
|UL 201||Garage Equipment.|
|UL 844||Electric Lighting Fixtures for Use in Hazardous Locations.|
OSHA's recognition of any NRTL for a particular test standard is limited to equipment or materials for which OSHA standards require third-party testing and certification before using them in the workplace. Consequently, if a test standard also covers any products for which OSHA does not require such testing and certification, an NRTL's scope of recognition does not include these products.
The American National Standards Institute (ANSI) may approve the test standards listed above as American National Standards. However, for convenience, we may use the designation of the standards-developing organization for the standard as opposed to the ANSI designation. Under the NRTL Program's policy (see OSHA Instruction CPL 1-0.3, Appendix C, paragraph XIV), any NRTL recognized for a particular test standard may use either the proprietary version of the test standard or the ANSI version of that standard. Contact ANSI to determine whether a test standard is currently ANSI-approved.
In addition to those conditions already required by 29 CFR 1910.7, SGS must abide by the following conditions of the recognition:
1. SGS must inform OSHA as soon as possible, in writing, of any change of ownership, facilities, or key personnel, and of any major change in its Start Printed Page 28359operations as an NRTL, and provide details of the change(s);
2. SGS must meet all the terms of its recognition and comply with all OSHA policies pertaining to this recognition; and
3. SGS must continue to meet the requirements for recognition, including all previously published conditions on SGS's scope of recognition, in all areas for which it has recognition.
Pursuant to the authority in 29 CFR 1910.7, OSHA hereby expands the scope of recognition of SGS, subject to the limitation and conditions specified above.
III. Authority and Signature
Dorothy Dougherty, Deputy Assistant Secretary of Labor for Occupational Safety and Health, 200 Constitution Avenue NW., Washington, DC 20210, authorized the preparation of this notice. Accordingly, the Agency is issuing this notice pursuant to 29 U.S.C. 657(g)(2), Secretary of Labor's Order No. 1-2012 (77 FR 3912, Jan. 25, 2012), and 29 CFR 1910.7.Start Signature
Signed at Washington, DC, on June 15, 2017.
Deputy Assistant Secretary of Labor for Occupational Safety and Health.
[FR Doc. 2017-12912 Filed 6-20-17; 8:45 am]
BILLING CODE 4510-26-P