This site displays a prototype of a “Web 2.0” version of the daily
Federal Register. It is not an official legal edition of the Federal
Register, and does not replace the official print version or the official
electronic version on GPO’s govinfo.gov.
The documents posted on this site are XML renditions of published Federal
Register documents. Each document posted on the site includes a link to the
corresponding official PDF file on govinfo.gov. This prototype edition of the
daily Federal Register on FederalRegister.gov will remain an unofficial
informational resource until the Administrative Committee of the Federal
Register (ACFR) issues a regulation granting it official legal status.
For complete information about, and access to, our official publications
and services, go to
About the Federal Register
on NARA's archives.gov.
The OFR/GPO partnership is committed to presenting accurate and reliable
regulatory information on FederalRegister.gov with the objective of
establishing the XML-based Federal Register as an ACFR-sanctioned
publication in the future. While every effort has been made to ensure that
the material on FederalRegister.gov is accurately displayed, consistent with
the official SGML-based PDF version on govinfo.gov, those relying on it for
legal research should verify their results against an official edition of
the Federal Register. Until the ACFR grants it official status, the XML
rendition of the daily Federal Register on FederalRegister.gov does not
provide legal notice to the public or judicial notice to the courts.
Rule
Enter a search term or FR citation e.g.
88 FR 38230 FR 78782024-13208USDA09/05/24RULE0503-AA39SORN
Choosing an item from
full text search results
will bring you to those results. Pressing enter in the search box
will also bring you to search results.
Choosing an item from
suggestions
will bring you directly to the content.
This AD is effective April 16, 2026. Emergency AD 2026-05-51, issued on March 6, 2026, which contained the requirements of this amendment, was effective with actual notice.
Table of Contents
Enhanced Content - Table of Contents
This table of contents is a navigational tool, processed from the
headings within the legal text of Federal Register documents.
This repetition of headings to form internal navigation links
has no substantive legal effect.
Comments are no longer being accepted.
See DATES for details.
1 comment has
been received at Regulations.gov.
Agencies review all submissions and may choose to redact, or withhold,
certain submissions (or portions thereof). Submitted comments may not be
available to be read until the agency has approved them.
Docket Title
Document ID
Comments
MCAI-2026-00217-R; Bell Helicopters Model 505 Helicopters; Levelling and Weighing – Aft Moveable Ballast Box Assembly Door Hinge Failure
FederalRegister.gov retrieves relevant information about this document
from Regulations.gov to provide users with additional context. This
information is not part of the official Federal Register document.
MCAI-2026-00217-R; Bell Helicopters Model 505 Helicopters; Levelling and Weighing – Aft Moveable Ballast Box Assembly Door Hinge Failure
Document page views are updated periodically throughout the day and are
cumulative counts for this document. Counts are subject to sampling,
reprocessing and revision (up or down) throughout the day.
Page views
376
as of
11/06/2026 at 8:15 pm EST
Other Formats
Enhanced Content - Other Formats
This document is also available in the following formats:
This PDF is FR Doc. 2026-06369 as it appeared on Public Inspection on
03/31/2026 at 8:45 am.
It was viewed
28
times while on Public Inspection.
If you are using public inspection listings for legal research, you
should verify the contents of the documents against a final, official
edition of the Federal Register. Only official editions of the
Federal Register provide legal notice of publication to the public and judicial notice
to the courts under 44 U.S.C. 1503 & 1507.
Learn more here.
Published Document: 2026-06369 (91 FR 16160)
This document has been published in the Federal Register. Use the PDF linked in the document sidebar for the official electronic format.
AGENCY:
Federal Aviation Administration (FAA), DOT.
ACTION:
Final rule; request for comments.
SUMMARY:
The FAA is adopting a new airworthiness directive (AD) for certain Bell Textron Canada Limited (Bell) Model 505 helicopters. The FAA previously sent this AD as an emergency AD to all known U.S. owners and operators of these helicopters. This AD was prompted by a failure of the hinge assembly on the aft movable ballast box assembly, which could allow the ballast weights to escape the ballast box and strike the tail rotor assembly. This AD requires revising the Limitations section of the existing rotorcraft flight manual (RFM) for the helicopter to prohibit the use of ballast weights within the aft movable ballast box assembly. The FAA is issuing this AD to address the unsafe condition on these products.
DATES:
This AD is effective April 16, 2026. Emergency AD 2026-05-51, issued on March 6, 2026, which contained the requirements of this amendment, was effective with actual notice.
The FAA must receive comments on this AD by May 18, 2026.
ADDRESSES:
You may send comments, using the procedures found in 14 CFR 11.43 and 11.45, by any of the following methods:
Federal eRulemaking Portal:
Go to
regulations.gov.
Follow the instructions for submitting comments.
Fax:
(202) 493-2251.
Mail:
U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE, Washington, DC 20590.
Hand Delivery:
Deliver to Mail address above between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays.
AD Docket:
You may examine the AD docket at regulations.gov under Docket No. FAA-2026-3472; or in person at Docket Operations between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this final rule, the mandatory continuing airworthiness information (MCAI), any comments received, and other information. The street address for Docket Operations is listed above.
FOR FURTHER INFORMATION CONTACT:
Kurt Landendorf, Aviation Safety Engineer, FAA, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; phone: (817) 222-5254; email:
kurt.d.ladendorf@faa.gov.
SUPPLEMENTARY INFORMATION:
Comments Invited
The FAA invites you to send any written data, views, or arguments about this final rule. Send your comments to an address listed under
ADDRESSES
. Include “Docket No. FAA-2026-3472; Project Identifier MCAI-2026-00217-R” at the beginning of your comments. The most helpful comments reference a specific portion of the final rule, explain the reason for any recommended change, and include supporting data. The FAA will consider all comments received by the closing date and may amend this final rule because of those comments.
Except for Confidential Business Information (CBI) as described in the following paragraph, and other information as described in 14 CFR 11.35, the FAA will post all comments received, without change, to
regulations.gov, including any personal information you provide. The agency will also post a report summarizing each substantive verbal contact received about this final rule.
Confidential Business Information
CBI is commercial or financial information that is both customarily and actually treated as private by its owner. Under the Freedom of Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public disclosure. If your comments responsive to this AD contain commercial or financial information that is customarily treated as private, that you actually treat as private, and that is relevant or responsive to this AD, it is important that you clearly designate the submitted comments as CBI. Please mark each page of your submission containing CBI as “PROPIN.” The FAA will treat such marked submissions as confidential under the FOIA, and they
( printed page 16161)
will not be placed in the public docket of this AD. Submissions containing CBI should be sent to Kurt Landendorf, Aviation Safety Engineer, FAA, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590. Any commentary that the FAA receives that is not specifically designated as CBI will be placed in the public docket for this rulemaking.
Background
The FAA issued Emergency AD 2026-05-51, dated March 6, 2026 (also referred to as the emergency AD), to address an unsafe condition on Bell Model 505 helicopters, serial numbers 65011 and subsequent with ballast box assembly part number (P/N) SLS-706-201-207 or P/N SLS-706-201-207FM installed. The FAA sent the emergency AD to all known U.S. owners and operators of these helicopters. The emergency AD requires revising the Limitations section of the existing RFM for the helicopter to prohibit the use of ballast weights within the aft movable ballast box assembly P/N SLS-706-201-207 or P/N SLS-706-201-207FM.
The emergency AD was prompted by Transport Canada Emergency AD CF-2026-12, dated March 3, 2026 (Transport Canada Emergency AD CF-2026-12) (also referred to as the MCAI), issued by Transport Canada, which is the aviation authority for Canada. The MCAI states that Bell has discovered possible plastic deformation and improper pin engagement in the knuckles of the door hinge on the aft movable ballast box assembly. Bell stated there was a failure of the current hinge assembly P/N SLS-706-201-169, which was found during a post flight inspection. Ballast weights escaping the ballast box have a high potential of striking the tail rotor assembly.
The FAA is issuing this AD to prevent damage to and/or departure of tail rotor blades, loss of tail rotor thrust, and severe vibrations. Any of these conditions, if not addressed, will lead to loss of control of the helicopter.
You may examine the MCAI in the AD docket at
regulations.gov
under Docket No. FAA-2026-3472.
FAA's Determination
These products have been approved by the civil aviation authority of another country and are approved for operation in the United States. Pursuant to the FAA's bilateral agreement with this State of Design Authority, that authority has notified the FAA of the unsafe condition described in the MCAI described above. The FAA is issuing this AD after determining that the unsafe condition described previously is likely to exist or develop on other products of the same type design.
AD Requirements
This AD requires revising the Limitations section of the existing RFM for the helicopter to prohibit the use of the ballast weights within the aft movable ballast box assembly P/N SLS-706-201-207 or SLS-706-201-207FM.
The owner/operator (pilot) holding at least a private pilot certificate may revise the existing RFM for the helicopter and must enter compliance into the helicopter maintenance records in accordance with 14 CFR 43.9(a) and 91.417(a)(2)(v). The pilot may perform this action because it only involves revising the RFM, which could be performed equally well by a pilot or a mechanic. This is an exception to the FAA's standard maintenance regulations.
Justification for Immediate Adoption and Determination of the Effective Date
Section 553(b) of the Administrative Procedure Act (APA) (5 U.S.C. 551et seq.) authorizes agencies to dispense with notice and comment procedures for rules when the agency, for “good cause,” finds that those procedures are “impracticable, unnecessary, or contrary to the public interest.” Under this section, an agency, upon finding good cause, may issue a final rule without providing notice and seeking comment prior to issuance. Further, section 553(d) of the APA authorizes agencies to make rules effective in less than thirty days, upon a finding of good cause.
An unsafe condition exists that required the immediate adoption of Emergency AD 2026-05-51 issued on March 6, 2026, to all known U.S. owners and operators of these helicopters. The FAA found that the risk to the flying public justified waiving notice and comment prior to adoption of this rule because ballast weights escaping the ballast box have a high potential of striking the tail rotor assembly, which could result in damage to and/or departure of tail rotor blades, loss of tail rotor thrust, and severe vibrations; these conditions will result in loss of control of the helicopter. In addition, this AD requires revising the existing RFM for the helicopter before further flight. This compliance time is shorter than the time necessary for the public to comment and for the publication of the final rule. These conditions still exist, therefore, notice and opportunity for prior public comment are impracticable and contrary to the public interest pursuant to 5 U.S.C. 553(b).
In addition, the FAA finds that good cause exists pursuant to 5 U.S.C. 553(d) for making this amendment effective in less than 30 days, for the same reasons the FAA found good cause to forgo notice and comment.
Regulatory Flexibility Act
The requirements of the Regulatory Flexibility Act (RFA) do not apply when an agency finds good cause pursuant to 5 U.S.C. 553 to adopt a rule without prior notice and comment. Because the FAA has determined that it has good cause to adopt this rule without prior notice and comment, RFA analysis is not required.
Interim Action
The FAA considers that this AD is an interim action. If final action is later identified, the FAA might consider additional rulemaking.
Costs of Compliance
The FAA estimates that this AD affects 174 helicopters of U.S. registry. The FAA estimates the following costs to comply with this AD:
Estimated Costs
Action
Labor cost
Parts cost
Cost per
product
Cost on U.S. operators
Revise the RFM
1 work-hour × $85 per hour = $85
$0
$85
$14,790
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. Subtitle VII: Aviation Programs describes in more detail the scope of the Agency's authority.
The FAA is issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section
( printed page 16162)
44701: General requirements. Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.
Regulatory Findings
This AD will not have federalism implications under Executive Order 13132. This AD will not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government.
For the reasons discussed above, I certify that this AD:
The FAA issued emergency Airworthiness Directive (AD) 2026-05-51 on March 6, 2026 (also referred to as the emergency AD), directly to affected owners and operators. As a result of such actual notice, the emergency AD was effective for those owners and operators on the date it was received. This AD contains the same requirements as the emergency AD and, for those who did not receive actual notice, is effective on April 16, 2026.
(b) Affected ADs
None.
(c) Applicability
This AD applies to Bell Textron Canada Limited Model 505 helicopters, certificated in any category, serial numbers 65011 and subsequent, with ballast box assembly part number (P/N) SLS-706-201-207 or P/N SLS-706-201-207FM installed.
(d) Subject
Joint Aircraft System Component (JASC) Code 2500, Equipment/furnishings.
(e) Unsafe Condition
This AD was prompted by a failure of the hinge assembly on the aft movable ballast box assembly, which could allow the ballast weights to escape the ballast box and strike the tail rotor assembly. The FAA is issuing this AD to prevent damage to and/or departure of tail rotor blades, loss of tail rotor thrust, and severe vibrations. The unsafe condition, if not addressed, could result in loss of control of the helicopter.
(f) Compliance
Comply with this AD within the compliance times specified, unless already done.
(g) Requirements
Before further flight, revise the Limitations section of the existing rotorcraft flight manual (RFM) for the helicopter by inserting the following text: “the use of the ballast weights within the aft movable ballast box assembly P/N SLS-706-201-207 or SLS-706-201-207FM, is prohibited.”
(1) Inserting a copy of this AD into the Limitations section of the RFM satisfies the requirements of paragraph (g) of this AD.
(2) For this AD, the owner/operator (pilot) holding at least a private pilot certificate may revise the existing RFM for the helicopter and must enter compliance into the helicopter maintenance records in accordance with 14 CFR 43.9(a) and 91.417(a)(2)(v). The record must be maintained as required by 14 CFR 91.417, 121.380, or 135.439.
(h) Special Flight Permits
Special flight permits, as described in 14 CFR 21.197 and 21.199, are not allowed.
(i) Alternative Methods of Compliance (AMOCs)
(1) The Manager, International Validation Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the manager of the International Validation Branch, send it to the attention of the person identified in paragraph (j) of this AD and email to:
AMOC@faa.gov.
(2) Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/certificate holding district office.
(j) Additional Information
For more information about this AD, contact Kurt Landendorf, Aviation Safety Engineer, FAA, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; phone: (817) 222-5254; email:
kurt.d.ladendorf@faa.gov.
1 comment has been received at Regulations.gov.
Agencies review all submissions and may choose to redact, or withhold, certain submissions (or portions thereof). Submitted comments may not be available to be read until the agency has approved them.