Federal Aviation Administration (FAA), Department of Transportation (DOT).
Notice of proposed rulemaking (NPRM).
We propose to adopt a new airworthiness directive (AD) for certain Cirrus Design Corporation (CDC) Models SR20 and SR22 airplanes. This proposed AD would require you to replace the cabin door rod ends at the upper and lower hinges of the cabin door with newly designed rod ends. This proposed AD results from two known occurrences of in-flight cabin door separation (one total separation and one retained by the door strut). The rod ends, a component of the door hinges, may fail and result in a door separation from the airplane while in flight. We are proposing this AD to prevent in-flight failure of the cabin door, which could result in door separation from the airplane.
We must receive comments on this proposed AD by August 13, 2007.
Use one of the following addresses to comment on this proposed AD:
• DOT Docket Web site: Go to
• Mail: U.S. Department of Transportation, Docket Operations, M–30, West Building Ground Floor, Room W12–140, 1200 New Jersey Avenue, SE., Washington, DC 20590.
• Fax: (202) 493–2251.
• Hand Delivery: U.S. Department of Transportation, Docket Operations, M–30, West Building Ground Floor, Room W12–140, 1200 New Jersey Avenue, SE., Washington, DC 20590, between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays.
• Federal eRulemaking Portal: Go to
For service information identified in this proposed AD, contact Cirrus Design Corporation, 4515 Taylor Circle, Duluth, Minnesota 55811; telephone: (218) 727–2737; Internet address:
Wess Rouse, Aerospace Engineer, 2300 East Devon Avenue, Room 107, Des Plaines, Illinois 60018; telephone: (847) 294–8113; fax: (847) 297–7834.
We invite you to send any written relevant data, views, or arguments regarding this proposed AD. Send your comments to an address listed under the
We will post all comments we receive, without change, to
We received notification by CDC of a door that separated from a CDC SR22 airplane while in-flight. During descent for landing, the door separated from the airplane and struck the tail of the airplane. There have been many occurrences of broken or bent lower door hinges on CDC Models SR20 and SR22 airplanes, most discovered before flight.
This condition, if not corrected, could result in door separation from the airplane.
We have reviewed Cirrus Design Corporation Service Bulletin SB 2X–52–07, dated May 3, 2007.
The service information describes procedures for the installation of newly designed rod ends for the cabin door.
We are proposing this AD because we evaluated all information and determined the unsafe condition described previously is likely to exist or develop on other products of the same type design. This proposed AD would require you to replace the cabin door rod ends at the upper and lower hinges of the cabin door with newly designed rod ends.
We estimate that this proposed AD would affect 1,562 airplanes in the U.S. registry.
We estimate the following costs to do the proposed replacement of the cabin door rod ends:
CDC will provide warranty credit as stated in Cirrus Design Corporation Service Bulletin SB 2X–52–07, dated May 3, 2007.
Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. Subtitle VII, Aviation Programs, describes in more detail the scope of the Agency's authority.
We are issuing this rulemaking under the authority described in subtitle VII, part A, subpart III, section 44701, “General requirements.” Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.
We have determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government.
For the reasons discussed above, I certify that the proposed regulation:
1. Is not a “significant regulatory action” under Executive Order 12866;
2. Is not a “significant rule” under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and
3. Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.
We prepared a regulatory evaluation of the estimated costs to comply with this proposed AD and placed it in the AD docket.
You may examine the AD docket that contains the proposed AD, the regulatory evaluation, any comments received, and other information on the Internet at
Air transportation, Aircraft, Aviation safety, Safety.
Accordingly, under the authority delegated to me by the Administrator, the FAA proposes to amend 14 CFR part 39 as follows:
1. The authority citation for part 39 continues to read as follows:
49 U.S.C. 106(g), 40113, 44701.
2. The FAA amends § 39.13 by adding the following new AD:
(a) We must receive comments on this airworthiness directive (AD) action by August 13, 2007.
(b) None.
(c) This AD applies to the following airplane models and serial numbers that are certificated in any category:
(d) This AD results from two known occurrences of in-flight cabin door separation (one total separation and one retained by the door strut). We are proposing this AD to prevent in-flight failure of the cabin door, which could result in door separation from the airplane.
(e) To address this problem, you must do the following, unless already done:
(f) The Manager, Chicago Aircraft Certification Office, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. Send information to ATTN: Wess Rouse, Aerospace Engineer, FAA, 2300 East Devon Avenue, Room 107, Des Plaines, Illinois 60018; telephone: (847) 294–8113; fax: (847) 297–7834. Before using any approved AMOC on any airplane to which the AMOC applies, notify your appropriate principal inspector (PI) in the FAA Flight Standards District Office (FSDO), or lacking a PI, your local FSDO.
(g) To get copies of the service information referenced in this AD, contact Cirrus Design Corporation, 4515 Taylor Circle, Duluth, Minnesota 55811; telephone: (218) 727–2737; Internet address: