Federal Aviation Administration (FAA), Department of Transportation (DOT).
Final rule.
We are adopting a new airworthiness directive (AD) for the products listed above. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
A case of loose bond (ungluing) of one mounting wooden block of the control stick base cover, found during the cover reinstallation, was reported to the Type Certificate Holder (TCH) and led to the issuance of the “recommended” Service Bulletin (SB) No. 031004 in February 2004. Since that date, other similar occurrences have been reported. This SB in its revision 1, has therefore been reclassified “mandatory” by the TCH.
We are issuing this AD to require actions to correct the unsafe condition on these products.
This AD becomes effective April 30, 2008.
On April 30, 2008, the Director of the Federal Register approved the incorporation by reference of certain publications listed in this AD.
You may examine the AD docket on the Internet at
Sarjapur Nagarajan, Aerospace Engineer, FAA, Small Airplane Directorate, 901 Locust, Room 301, Kansas City, Missouri 64106; telephone: (816) 329–4145; fax: (816) 329–4090.
We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR part 39 to include an AD that would apply to the specified products. That NPRM was published in the
A case of loose bond (ungluing) of one mounting wooden block of the control stick base cover, found during the cover reinstallation, was reported to the Type Certificate Holder (TCH) and led to the issuance of the “recommended” Service Bulletin (SB) No.031004 in February 2004. Since that date, other similar occurrences have been reported. This SB in its revision 1, has therefore been reclassified “mandatory” by the TCH.
This Airworthiness Directive (AD) mandates inspection of the mounting blocks of the control stick base cover for loose bonds and repair, as necessary.
These actions are intended to address the identified unsafe condition so as to prevent separation of the mounting blocks from the wing spar which could result in restricted movement of the ailerons and elevators with possible partial or complete loss of controls.
The MCAI requires an inspection of the four mounting wooden blocks of the control stick base cover. You are to take corrective action by repairing any loose blocks where inspection indicates necessary.
We gave the public the opportunity to participate in developing this AD. We received no comments on the NPRM or on the determination of the cost to the public.
We reviewed the available data and determined that air safety and the public interest require adopting the AD as proposed.
We have reviewed the MCAI and related service information and, in general, agree with their substance. But we might have found it necessary to use different words from those in the MCAI to ensure the AD is clear for U.S. operators and is enforceable. In making these changes, we do not intend to differ substantively from the information provided in the MCAI and related service information.
We might also have required different actions in this AD from those in the MCAI in order to follow FAA policies. Any such differences are highlighted in a NOTE within the AD.
We estimate that this AD will affect 52 products of U.S. registry. We also estimate that it will take about .5 work-hour per product to comply with basic requirements of this AD. The average labor rate is $80 per work-hour. Required parts will cost about $135 per product.
Based on these figures, we estimate the cost of this AD to the U.S. operators to be $9,100 or $175 per product.
Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. “Subtitle VII: Aviation Programs,” describes in more detail the scope of the Agency's authority.
We are issuing this rulemaking under the authority described in “Subtitle VII, Part A, Subpart III, Section 44701: General requirements.” Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.
We determined that this AD will not have federalism implications under Executive Order 13132. This AD will not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government.
For the reasons discussed above, I certify this AD:
(1) Is not a “significant regulatory action” under Executive Order 12866;
(2) Is not a “significant rule” under DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and
(3) Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.
We prepared a regulatory evaluation of the estimated costs to comply with this AD and placed it in the AD Docket.
You may examine the AD docket on the Internet at
Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety.
49 U.S.C. 106(g), 40113, 44701.
(a) This airworthiness directive (AD) becomes effective April 30, 2008.
(b) None.
(c) This AD applies to the following CAP 10 B airplanes that are certificated in any category:
(i) serial numbers 300 through 310; and
(ii) serial numbers 1 through 40 that have been retrofitted with carbon/wood wing reference 5702–0104048* (*with or without a variable letter or number at the reference end).
(d) Air Transport Association of America (ATA) Code 57: Wings.
(e) The mandatory continuing airworthiness information (MCAI) states:
A case of loose bond (ungluing) of one mounting wooden block of the control stick base cover, found during the cover reinstallation, was reported to the Type Certificate Holder (TCH) and led to the issuance of the “recommended” Service Bulletin (SB) No. 031004 in February 2004. Since that date, other similar occurrences have been reported. This SB in its revision 1, has therefore been reclassified “mandatory” by the TCH.
This Airworthiness Directive (AD) mandates inspection of the mounting blocks of the control stick base cover for loose bonds and repair, as necessary.
These actions are intended to address the identified unsafe condition so as to prevent separation of the mounting blocks from the wing spar which could result in restricted movement of the ailerons and elevators with possible partial or complete loss of controls.
The MCAI requires an inspection of the four mounting wooden blocks of the control stick base cover. You are to take corrective action by repairing any loose blocks where inspection indicates necessary.
(f) Unless already done, do the following actions within the next 6 months after April 30, 2008 (the effective date of this AD), following APEX Aircraft Service Bulletin No. 031004 R1, Revision 1, dated November 12, 2007:
(1) Inspect the four mounting wooden blocks of the control stick base cover for loose bonding (gluing); and
(2) If any wooden block is found to be loose, take corrective action.
This AD differs from the MCAI and/or service information as follows: No differences.
(g) The following provisions also apply to this AD:
(1)
(2)
(3)
(h) Refer to MCAI European Aviation Safety Agency AD No.: 2007–0296, dated December 7, 2007; and APEX Aircraft Service Bulletin (SB) No. 031004 R1, Revision 1, dated November 12, 2007, for related information.
(i) You must use APEX Aircraft Service Bulletin (SB) No. 031004 R1, Revision 1, dated November 12, 2007, to do the actions required by this AD, unless the AD specifies otherwise.
(1) The Director of the Federal Register approved the incorporation by reference of this service information under 5 U.S.C. 552(a) and 1 CFR part 51.
(2) For service information identified in this AD, contact Apex Aircraft, Bureau de Navigabilité, 1, route de Troyes, 21121 DAROIS—France; telephone: +33 380 35 65 10; fax +33 380 35 65 15; e-mail:
(3) You may review copies at the FAA, Central Region, Office of the Regional Counsel, 901 Locust, Room 506, Kansas City, Missouri 64106; or at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202–741–6030, or go to: