Federal Aviation Administration (FAA), Department of Transportation (DOT).
Notice of proposed rulemaking (NPRM).
We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD results from mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as:
We must receive comments on this proposed AD by March 16, 2009.
You may send comments by any of the following methods:
•
•
•
•
You may examine the AD docket on the Internet at
Doug Rudolph, Aerospace Engineer, FAA, Small Airplane Directorate, 901 Locust, Room 301, Kansas City, Missouri 64016; telephone: (816) 329–4059; fax: (816) 329–4090.
We invite you to send any written relevant data, views, or arguments about this proposed AD. Send your comments to an address listed under the
We will post all comments we receive, without change, to
The European Aviation Safety Agency (EASA), which is the Technical Agent for the Member States of the European Community, has issued AD No. 2009–0007, dated January 13, 2009, (referred to after this as “the MCAI”), to correct an unsafe condition for the specified products. The MCAI states:
This Airworthiness Directive (AD) is prompted by some occurrences where the Deice Pressure Regulator has vented too much hot air into the forward compartment damaging the oxygen cylinder ON/OFF cable, the Ram-Air Scoop cable and the Environmental Control System (ECS) firewall shut-off valve cable.
Pilatus Aircraft Ltd. has issued Pilatus PC12 Service Bulletin No. 30–011, dated July 9, 2008. The actions described in this service information are intended to correct the unsafe condition identified in the MCAI.
This product has been approved by the aviation authority of another country, and is approved for operation in the United States. Pursuant to our bilateral agreement with this State of Design Authority, they have notified us of the unsafe condition described in the MCAI and service information referenced above. We are proposing this AD because we evaluated all information and determined the unsafe condition exists and is likely to exist or develop on other products of the same type design.
We have reviewed the MCAI and related service information and, in general, agree with their substance. But we might have found it necessary to use different words from those in the MCAI to ensure the AD is clear for U.S. operators and is enforceable. In making these changes, we do not intend to differ substantively from the information provided in the MCAI and related service information.
We might also have proposed different actions in this AD from those in the MCAI in order to follow FAA policies. Any such differences are highlighted in a NOTE within the proposed AD.
We estimate that this proposed AD will affect 131 products of U.S. registry. We also estimate that it would take about 2 work-hours per product to comply with the basic requirements of this proposed AD. The average labor rate is $80 per work-hour. Required parts would cost about $1,000 per product. Where the service information lists required parts costs that are covered under warranty, we have assumed that there will be no charge for these costs. As we do not control warranty coverage for affected parties, some parties may incur costs higher than estimated here.
Based on these figures, we estimate the cost of the proposed AD on U.S. operators to be $20,960, or $160 per product.
Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. “Subtitle VII: Aviation Programs,” describes in more detail the scope of the Agency's authority.
We are issuing this rulemaking under the authority described in “Subtitle VII, Part A, Subpart III, Section 44701: General requirements.” Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.
We determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government.
For the reasons discussed above, I certify this proposed regulation:
1. Is not a “significant regulatory action” under Executive Order 12866;
2. Is not a “significant rule” under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and
3. Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.
We prepared a regulatory evaluation of the estimated costs to comply with this proposed AD and placed it in the AD docket.
Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety.
Accordingly, under the authority delegated to me by the Administrator, the FAA proposes to amend 14 CFR part 39 as follows:
1. The authority citation for part 39 continues to read as follows:
49 U.S.C. 106(g), 40113, 44701.
2. The FAA amends § 39.13 by adding the following new AD:
(a) We must receive comments by March 16, 2009.
(b) None.
(c) This AD applies to Models PC–12 and PC–12/45 airplanes, manufacturer's serial numbers (MSN) 101 through MSN 320, certificated in any category.
(d) Air Transport Association of America (ATA) Code 30: Ice and Rain Protection.
(e) The mandatory continuing airworthiness information (MCAI) states:
(f) Unless already done, within the next 3 months after the effective date of this AD, install an overboard vent for the airfoil deice system pressure regulator (Modification Kit Number 500.50.12.332) following the Accomplishment Instructions in Pilatus Aircraft Ltd. PC12 Service Bulletin No. 30–011, dated July 9, 2008.
This AD differs from the MCAI and/or service information as follows: No differences.
(g) The following provisions also apply to this AD:
(1) Alternative Methods of Compliance (AMOCs): The Manager, Standards Office, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. Send information to ATTN: Doug Rudolph, Aerospace Engineer, FAA, Small Airplane Directorate, 901 Locust, Room 301, Kansas City, Missouri 64016; telephone: (816) 329–4059; fax: (816) 329–4090. Before using any approved AMOC on any airplane to which the AMOC applies, notify your appropriate principal inspector (PI) in the FAA Flight Standards District Office (FSDO), or lacking a PI, your local FSDO.
(2) Airworthy Product: For any requirement in this AD to obtain corrective actions from a manufacturer or other source, use these actions if they are FAA-approved. Corrective actions are considered FAA-approved if they are approved by the State of Design Authority (or their delegated agent). You are required to assure the product is airworthy before it is returned to service.
(3) Reporting Requirements: For any reporting requirement in this AD, under the provisions of the Paperwork Reduction Act (44 U.S.C. 3501 et seq.), the Office of Management and Budget (OMB) has approved the information collection requirements and has assigned OMB Control Number 2120–0056.
(h) Refer to MCAI European Aviation Safety Agency (EASA) AD No. 2009–0007, dated January 13, 2009; and Pilatus Aircraft Ltd. PC12 Service Bulletin No. 30–011, dated July 9, 2008, for related information.