Federal Aviation Administration (FAA), DOT.
Notice of proposed special conditions.
This action proposes special conditions for the Boeing Model 747–8/–8F airplane. This airplane will have novel or unusual design features associated with a four-post main landing gear system. The applicable airworthiness regulations do not contain adequate or appropriate safety standards for this design feature. These proposed special conditions contain the additional safety standards that the Administrator considers necessary to establish a level of safety equivalent to that established by the existing airworthiness standards.
Comments must be received on or before June 11, 2009.
Comments on this proposal may be mailed in duplicate to: Federal Aviation Administration, Transport Airplane Directorate, Attention: Rules Docket (ANM–113), Docket No. NM403, 1601 Lind Avenue, SW., Renton, Washington 98057–3356; or delivered in duplicate to the Transport Airplane Directorate at the above address. All comments must be marked Docket No. NM403. Comments may be inspected in the Rules Docket weekdays, except Federal holidays, between 7:30 a.m. and 4 p.m.
Mark Freisthler, FAA, Airframe & Cabin Safety Branch, ANM–115, Transport Airplane Directorate, Aircraft Certification Service, 1601 Lind Avenue, SW., Renton, Washington 98057–3356; telephone (425) 227–1119; facsimile (425) 227–1149.
The FAA invites interested persons to participate in this rulemaking by submitting written comments, data, or views. The most helpful comments reference a specific portion of the special conditions, explain the reason for any recommended change, and include supporting data. We ask that you send us two copies of written comments.
We will file in the docket all comments we receive as well as a report summarizing each substantive public contact with FAA personnel concerning these proposed special conditions. The docket is available for public inspection before and after the comment closing date. If you wish to review the docket in person, go to the address in the
We will consider all comments we receive on or before the closing date for comments. We will consider comments filed late if it is possible to do so without incurring expense or delay. We may change the proposed special conditions based on comments we receive.
If you want the FAA to acknowledge receipt of your comments on this proposal, include with your comments a pre-addressed, stamped postcard on which the docket number appears. We will stamp the date on the postcard and mail it back to you.
On November 4, 2005, The Boeing Company, PO Box 3707, Seattle, WA 98124, applied for an amendment to Type Certificate Number A20WE to include the new Model 747–8 passenger airplane and the new Model 747–8F freighter airplane. The Model 747–8 and the Model 747–8F are derivatives of the 747–400 and the 747–400F, respectively. Both the Model 747–8 and the Model 747–8F are four-engine jet transport airplanes that will have a maximum takeoff weight of 970,000 pounds and new General Electric GEnx–2B67 engines. The Model 747–8 will have two flight crew and the capacity to carry 660 passengers. The Model 747–8F will have two flight crew and a zero passenger capacity, although Boeing has submitted a petition for exemption to allow the carriage of supernumeraries.
Under the provisions of 14 CFR 21.101, Boeing must show that the Model 747–8 and 747–8F (hereafter referred as 747–8/–8F) meet the applicable provisions of part 25, as amended by Amendments 25–1 through 25–117, except for earlier amendments as agreed upon by the FAA. These regulations will be incorporated into Type Certificate No. A20WE after type certification approval of the 747–8/–8F.
In addition, the certification basis includes other regulations, special conditions and exemptions that are not relevant to these proposed special conditions. Type Certificate No. A20WE will be updated to include a complete description of the certification basis for these model airplanes.
If the Administrator finds that the applicable airworthiness regulations (
In addition to the applicable airworthiness regulations and special conditions, the 747–8/–8F must comply with the fuel vent and exhaust emission requirements of 14 CFR part 34 and the noise certification requirements of 14 CFR part 36.
Special conditions, as defined in § 11.19, are issued under § 11.38, and become part of the type certification basis under § 21.101.
Special conditions are initially applicable to the model for which they are issued. Should the type certificate for that model be amended later to include any other model that incorporates the same or similar novel or unusual design feature, or should any other model already included on the same type certificate be modified to incorporate the same or similar novel or unusual design feature, the special conditions would also apply to the other model under § 21.101.
The Boeing Model 747–8/–8F airplane will incorporate the following novel or unusual design features: a four-post main landing gear system with two wing
The Boeing Model 747–8/–8F airplane will retain the landing gear arrangement which is unique to the 747 family of airplanes. The conventional arrangement for the main landing gear of transport category airplanes is two-underwing posts. The 747 was the first to introduce a four-post main landing gear arrangement, two underwing posts supplemented by two body posts. This arrangement was adopted to accommodate the then unprecedented increased weight and size of the Model 747 airplane.
Existing regulations are written to address the conventional landing gear configuration commonly found on transport category airplanes. This being the case, they are not appropriate to address the unique features of the Boeing 747 design. The increased number of posts alters the load distribution between the gear units during landing and ground handling conditions addressed by the regulations. This arrangement also loads the airframe differently than conventional landing gear designs. The FAA determined that, while the general conditions addressed by §§ 25.473 and 25.479 through 25.485 were still applicable, specific details contained in these regulations may not be directly relatable to the four-post arrangement.
In 1968 the FAA issued Special Condition A–4 to address the ground load requirements for the main landing gear system for Boeing Model 747–100 series airplanes. That special condition provided clarification on the applicability of §§ 25.473 and 25.479 through 25.485 to the Model 747 airplane. In 1971 Special Condition A–4 was amended to address Boeing Model 747 airplanes with the landing gear load evener system deleted or made inoperable.
The FAA has determined that Special Condition A–4 is applicable to the 747–8/8F series airplanes, provided that all the applicable part 25 regulations cited in Special Condition A–4 (recorded as an enclosure to FAA Letter WE–120/8110 (CT3488WE–D) to the Boeing Company, dated May 12, 1971) are upgraded to the latest amendment level (
As discussed above, these proposed special conditions are applicable to Boeing Model 747–8/–8F airplanes. Should Boeing apply at a later date for a change to the type certificate to include another model incorporating the same novel or unusual design features, these proposed special conditions would apply to that model as well under the provisions of § 21.101.
This action affects only certain novel or unusual design features of the Boeing Model 747–8/–8F airplanes. It is not a rule of general applicability.
Aircraft, Aviation safety, Reporting and recordkeeping requirements.
The authority citation for these Special Conditions is as follows:
49 U.S.C. 106(g), 40113, 44701, 44702, 44704.
Accordingly, the Federal Aviation Administration (FAA) proposes the following special conditions as part of the type certification basis for the Boeing Model 747–8/–8F airplanes.
The requirements of §§ 25.471, 25.473, and 25.479 through 25.485 apply as follows:
1.
2.
3.
4.
5.
6.
This condition need not be coupled with either a 6 fps landing at maximum take off weight or a 12 fps reserve energy drop test.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19. Substantiation of the design criteria must include a dynamic taxi and landing analysis.