Federal Aviation Administration (FAA), Department of Transportation (DOT).
Final rule; request for comments.
We are adopting a new airworthiness directive (AD) for certain Airbus Model A330–201, –202, –203, –223, –243, –301, –302, –303, –321, –322, –323, –341, –342, and –343 airplanes; and Model A340–200 and –300 series airplanes. This AD requires repetitive inspections of the main fitting and sliding tube of the nose landing gear (NLG) for defects, damage, and cracks, and corrective actions if necessary. This AD was prompted by reports of a cracked main fitting and sliding tube during overhaul of NLGs. We are issuing this AD to detect and correct cracks, defects, or damage of the main fitting and sliding tube of the NLG, which could result in failure of the main fitting or sliding tube, and consequent NLG collapse.
This AD becomes effective April 30, 2012.
The Director of the Federal Register approved the incorporation by reference of certain publications listed in the AD as of April 30, 2012.
We must receive comments on this AD by May 29, 2012.
You may send comments by any of the following methods:
•
•
•
•
You may examine the AD docket on the Internet at
Vladimir Ulyanov, Aerospace Engineer, International Branch, ANM–116, Transport Airplane Directorate, FAA, 1601 Lind Avenue SW., Renton, Washington 98057–3356; telephone (425) 227–1138; fax (425) 227–1149.
The European Aviation Safety Agency (EASA), which is the Technical Agent for the Member States of the European Community, has issued EASA Airworthiness Directive 2010–0034, dated March 5, 2010, corrected March 8, 2010 (referred to after this as “the MCAI”), to correct an unsafe condition for the specified products. The MCAI states:
During the overhaul of two different Nose Landing Gears (NLG), cracks were found on the main fitting of one and the sliding tube of the other. Investigations concluded that the cracks initiated as a result of residual stress in the parts following damage due to impact during towing incidents.
A subsequent review of the reported incidents has led to conclude that an inspection of the main fitting and sliding tube is required on those NLG that have sustained impacts as result of towing incidents.
The failure of the main fitting or sliding tube could lead to NLG collapse.
To prevent the above unsafe condition, this [EASA] AD requires a one-time [detailed] inspection followed by repetitive inspections of the main fitting and sliding tube of the NLG serial numbers listed in the Applicability section of this [EASA] AD:
This [EASA] AD also requires the accomplishment of the associated corrective actions, as necessary.
Airbus has issued Mandatory Service Bulletin A330–32–3233, dated October 22, 2009 (for Model A330 airplanes); and Mandatory Service Bulletin A340–32–4275, dated October 22, 2009 (for Model A340 airplanes). The actions described in this service information are intended to correct the unsafe condition identified in the MCAI.
This product has been approved by the aviation authority of another country, and is approved for operation in the United States. Pursuant to our bilateral agreement with the State of Design Authority, we have been notified of the unsafe condition described in the MCAI and service information referenced above. We are issuing this AD because we evaluated all pertinent information and determined the unsafe condition exists and is likely to exist or develop on other products of the same type design.
There are no products of this type currently registered in the United States. However, this rule is necessary to ensure that the described unsafe condition is addressed if any of these products are placed on the U.S. Register in the future.
Since there are currently no domestic operators of this product, notice and opportunity for public comment before issuing this AD are unnecessary.
This AD is a final rule that involves requirements affecting flight safety, and we did not precede it by notice and opportunity for public comment. We invite you to send any written relevant data, views, or arguments about this AD. Send your comments to an address listed under the
We will post all comments we receive, without change, to
Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. “Subtitle VII: Aviation Programs,” describes in more detail the scope of the Agency's authority.
We are issuing this rulemaking under the authority described in “Subtitle VII, Part A, Subpart III, Section 44701: General requirements.” Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.
We determined that this AD will not have federalism implications under Executive Order 13132. This AD will not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government.
1. Is not a “significant regulatory action” under Executive Order 12866;
2. Is not a “significant rule” under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979);
3. Will not affect intrastate aviation in Alaska; and
4. Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.
We prepared a regulatory evaluation of the estimated costs to comply with this AD and placed it in the AD docket.
Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety.
Accordingly, under the authority delegated to me by the Administrator, the FAA amends 14 CFR part 39 as follows:
49 U.S.C. 106(g), 40113, 44701.
This airworthiness directive (AD) becomes effective April 30, 2012.
None.
This AD applies to the airplanes identified in paragraphs (c)(1) and (c)(2) of this AD, certificated in any category, all serial numbers, if fitted with the nose landing gear (NLG) identified in table 1 of this AD.
(1) Airbus Model A330–201, –202, –203, –223, –243, –301, –302, –303, –321, –322, –323, –341, –342, and –343 airplanes.
(2) Airbus Model A340–211, –212, –213, –311, –312, and –313 airplanes.
Air Transport Association (ATA) of America Code 32: Landing Gear.
This AD was prompted by reports of a cracked main fitting and sliding tube during overhaul of NLGs. We are issuing this AD to detect and correct cracks, defects, or damage of the main fitting and sliding tube of the NLG, which could result in failure of the main fitting or sliding tube, and consequent NLG collapse.
You are responsible for having the actions required by this AD performed within the compliance times specified, unless the actions have already been done.
Within 900 flight hours after the effective date of this AD: Do a detailed inspection of the NLG main fitting and sliding tube for any cracks, defects, and damage of the paint or surface protection, including paint removal and cracking of the surface treatment. Before further flight after doing the detailed inspection of the NLG, remove the labels, paint, surface protection coatings, and cadmium from the NLG main fitting; do a detailed inspection for any damage to the surface that will impair the magnetic particle inspection (MPI); and, if any defects are found, before further flight remove any defects by polishing. Do all actions specified in paragraph (g) of this AD in accordance with the Accomplishment Instructions of Airbus Mandatory Service Bulletin A330–32–3233, dated October 22, 2009 (for Model A330 airplanes); or Airbus Mandatory Service Bulletin A340–32–4275, dated October 22, 2009 (for Model A340 airplanes).
Before further flight after doing the actions required in paragraph (g) of this AD: Do an MPI for cracking of the NLG main fitting and sliding tube, in accordance with the Accomplishment Instructions of Airbus Mandatory Service Bulletin A330–32–3233, dated October 22, 2009 (for Model A330 airplanes); or Airbus Mandatory Service Bulletin A340–32–4275, dated October 22, 2009 (for Model A340 airplanes).
(1) If no crack is detected during the MPI required by paragraph (h) of this AD: Before further flight, flap peen the inspected area where the paint and cadmium has been removed, and replace the protective coatings, in accordance with the Accomplishment Instructions of Airbus Mandatory Service Bulletin A330–32–3233, dated October 22, 2009 (for Model A330 airplanes); or Airbus Mandatory Service Bulletin A340–32–4275, dated October 22, 2009 (for Model A340 airplanes).
(2) If any crack is detected during the MPI required by paragraph (h) of this AD: Before further flight, replace the damaged part with a new or serviceable part, in accordance with the Accomplishment Instructions of Airbus Mandatory Service Bulletin A330–32–3233, dated October 22, 2009 (for Model A330 airplanes); or Airbus Mandatory Service Bulletin A340–32–4275, dated October 22, 2009 (for Model A340 airplanes).
Within 900 flight hours after accomplishing the actions in paragraphs (g) and (h) of this AD: Do a detailed inspection of the surface treatment of the NLG main fitting and sliding tube for any cracks, defects, and damage of the paint or surface protection, including paint removal and cracking, in accordance with the Accomplishment Instructions of Airbus Mandatory Service Bulletin A330–32–3233, dated October 22, 2009 (for Model A330 airplanes); or Airbus Mandatory Service Bulletin A340–32–4275, dated October 22, 2009 (for Model A340 airplanes).
(1) If no crack, defect, or damage is detected during the detailed inspection required by paragraph (i) of this AD: Repeat the inspection thereafter at intervals not to exceed 900 flight hours.
(2) If any crack, defect, or damage is detected during the detailed inspection
(i) If no crack is detected during the MPI required by paragraph (i)(2) of this AD: Before further flight, flap peen the inspected area where the paint and cadmium has been removed, and replace the protective coatings, in accordance with the Accomplishment Instructions of Airbus Mandatory Service Bulletin A330–32–3233, dated October 22, 2009 (for Model A330 airplanes); or Airbus Mandatory Service Bulletin A340–32–4275, dated October 22, 2009 (for Model A340 airplanes).
(ii) If any crack is detected during the MPI required by paragraph (i)(2) of this AD: Before further flight, replace the damaged part with a new or serviceable part, in accordance with the Accomplishment Instructions of Airbus Mandatory Service Bulletin A330–32–3233, dated October 22, 2009 (for Model A330 airplanes); or Airbus Mandatory Service Bulletin A340–32–4275, dated October 22, 2009 (for Model A340 airplanes). Repeat the inspection required by paragraph (i) of this AD thereafter at intervals not to exceed 900 flight hours.
The following provisions also apply to this AD:
(1)
(2)
Refer to Mandatory Continuing Airworthiness Information (MCAI) European Aviation Safety Agency (EASA) Airworthiness Directive 2010–0034, dated March 5, 2010, corrected March 8, 2010, and the following service information, for related information.
(1) Airbus Mandatory Service Bulletin A330–32–3233, dated October 22, 2009.
(2) Airbus Mandatory Service Bulletin A340–32–4275, dated October 22, 2009.
(1) You must use the following service information to do the actions required by this AD, unless the AD specifies otherwise. The Director of the Federal Register approved the incorporation by reference (IBR) of the following service information under 5 U.S.C. 552(a) and 1 CFR part 51:
(i) Airbus Mandatory Service Bulletin A330–32–3233, dated October 22, 2009.
(ii) Airbus Mandatory Service Bulletin A340–32–4275, dated October 22, 2009.
(2) For service information identified in this AD, contact Airbus SAS—Airworthiness Office—EAL, 1 Rond Point Maurice Bellonte, 31707 Blagnac Cedex, France; telephone +33 5 61 93 36 96; fax +33 5 61 93 45 80; email
(3) You may review copies of the service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, Washington. For information on the availability of this material at the FAA, call 425–227–1221.
(4) You may also review copies of the service information that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202–741–6030, or go to: