Import Administration, International Trade Administration, Department of Commerce.
As a result of the determinations by the Department of Commerce (the Department) that revocation of the antidumping duty (AD) orders on (1) certain circular welded carbon steel pipes and tubes from India, Thailand, and Turkey; (2) certain circular welded non-alloy steel pipe from Brazil, Mexico, the Republic of Korea, and Taiwan; and (3) certain circular welded carbon steel pipes and tubes from Taiwan would likely lead to continuation or recurrence of dumping, that revocation of the countervailing duty (CVD) order on certain circular welded carbon steel pipes and tubes from Turkey would likely lead to continuation or recurrence of a countervailable subsidy, and the determinations by the International Trade Commission (the ITC) that revocation of these AD and CVD orders would likely lead to a continuation or recurrence of material injury to an industry in the United States, the Department is publishing this notice of the continuation of these AD orders and CVD order.
Effective July 17, 2012.
James Terpstra or Robert James (AD orders) or Eric Greynolds (CVD order), AD/CVD Operations, Import Administration, International Trade Administration, U.S. Department of Commerce, 14th Street and Constitution Avenue NW., Washington, DC 20230; telephone: (202) 482–3965, (202) 482–0649, and (202) 482–6071, respectively.
On July 1, 2011, the Department initiated and the ITC instituted sunset reviews of the AD and CVD orders on certain circular welded carbon steel pipes and tubes from India, Thailand, and Turkey, certain circular welded non-alloy steel pipe from Brazil, Mexico, the Republic of Korea, and Taiwan, and certain circular welded carbon steel pipes and tubes from Taiwan pursuant to sections 751(c) and 752 of the Tariff Act of 1930, as amended (the Act), respectively.
On July 5, 2012, the ITC published its determination, pursuant to section 751(c) of the Act, that revocation of the AD and CVD orders on certain pipe and tube from Brazil, India, Korea, Mexico, Taiwan, Thailand, and Turkey would likely lead to continuation or recurrence of material injury within a reasonably foreseeable time.
The products covered by these AD and CVD orders are identified in the Appendix to this notice.
As a result of the determinations by the Department and the ITC that revocation of these AD and CVD orders would likely lead to continuation or recurrence of dumping or a countervailable subsidy, and of material injury to an industry in the United States, pursuant to section 751(d)(2) of the Act, the Department hereby orders the continuation of the AD and CVD orders on certain circular welded carbon steel pipes and tubes from India, Thailand, and Turkey, certain circular welded non-alloy steel pipe from Brazil, Mexico, the Republic of Korea, and Taiwan, and certain circular welded carbon steel pipes and tubes from Taiwan.
U.S. Customs and Border Protection will continue to collect cash deposits at the rates in effect at the time of entry for all imports of subject merchandise. The effective date of the continuation of these orders is the date of publication in the
These five-year (sunset) reviews and notice are in accordance with section 751(c) of the Act and published pursuant to section 777(i)(1) of the Act.
The products covered by the order include certain welded carbon steel standard pipes and tubes with an outside diameter of 0.375 inch or more but not over 16 inches. These products are commonly referred to in the industry as standard pipes and tubes produced to various American Society for Testing Materials (ASTM) specifications, most notably A–53, A–120, or A–135.
The antidumping duty order on certain welded carbon steel standard pipes and tubes from India, published on May 12, 1986, included standard scope language which used the import classification system as defined by Tariff Schedules of the United States, Annotated (TSUSA). The United States developed a system of tariff classification based on the international harmonized system of customs nomenclature. On January 1, 1989, the U.S. tariff schedules were fully converted from the TSUSA to the Harmonized Tariff Schedule (HTS).
Until January 1, 1989, such merchandise was classifiable under item numbers 610.3231, 610.3234, 610.3241, 610.3242, 610.3243, 610.3252, 610.3254, 610.3256, 610.3258, and 610.4925 of the TSUSA. This merchandise is currently classifiable under HTS item numbers 7306.30.1000, 7306.30.5025, 7306.30.5032, 7306.30.5040, 7306.30.5055, 7306.30.5085, 7306.30.5090. As with the TSUSA numbers, the HTS numbers are provided for convenience and customs purposes. The written product description remains dispositive.
The products covered by the order include certain welded carbon steel standard pipes and tubes with an outside diameter of 0.375 inch or more but not over 16 inches. These products are commonly referred to in the industry as standard pipes and tubes produced to various ASTM specifications, most notably A–53, A–120, or A–135.
The antidumping duty order on certain welded carbon steel standard pipes and tubes from India, published on May 12, 1986, included standard scope language which used the import classification system as defined by TSUSA. The United States developed a system of tariff classification based on the international harmonized system of customs nomenclature. On January 1, 1989, the U.S. tariff schedules were fully converted from the TSUSA to the HTS.
Until January 1, 1989, such merchandise was classifiable under item numbers 610.3231, 610.3234, 610.3241, 610.3242, 610.3243, 610.3252, 610.3254, 610.3256, 610.3258, and 610.4925 of the TSUSA. This merchandise is currently classifiable under HTS item numbers 7306.30.1000, 7306.30.5025, 7306.30.5032, 7306.30.5040, 7306.30.5055, 7306.30.5085, 7306.30.5090. As with the TSUSA numbers, the HTS numbers are provided for convenience and customs purposes. The written product description remains dispositive.
The products covered by this order include circular welded non-alloy steel pipes and tubes, of circular cross-section, not more than 406.4 millimeters (16 inches) in outside diameter, regardless of wall thickness, surface finish (black, or galvanized, painted), or end finish (plain end, beveled end, threaded and coupled). Those pipes and tubes are generally known as standard pipe, though they may also be called structural or mechanical tubing in certain applications. Standard pipes and tubes are intended for the low pressure conveyance of water, steam, natural gas, air, and other liquids and gases in plumbing and heating systems, air conditioner units, automatic sprinkler systems, and other related uses. Standard pipe may also be used for light load-bearing and mechanical applications, such as for fence tubing, and for protection of electrical wiring, such as conduit shells.
The scope is not limited to standard pipe and fence tubing, or those types of mechanical and structural pipe that are used in standard pipe applications. All carbon steel pipes and tubes within the physical description outlined above are included in the scope of this order, except for line pipe, oil country tubular goods, boiler tubing, cold-drawn or cold-rolled mechanical tubing, pipe and tube hollows for redraws, finished scaffolding, and finished rigid conduit.
Imports of these products are currently classifiable under the following HTSUS subheadings: 7306.30.10.00, 7306.30.50.25, 7306.30.50.32, 7306.30.50.40, 7306.30.50.55, 7306.30.50.85, and 7306.30.50.90. Although
The products covered by the order are certain welded carbon steel pipe and tube with an outside diameter of 0.375 inch or more, but not over 16 inches, of any wall thickness (pipe and tube) from Turkey. These products are currently provided for under the HTSUS as item numbers 7306.30.10, 7306.30.50, and 7306.90.10. Although the HTSUS subheadings are provided for convenience and customs purposes, the written description of the merchandise is dispositive.
The products covered by the orders are circular welded non-alloy steel pipes and tubes, of circular cross-section, not more than 406.4 millimeters (16 inches) in outside diameter, regardless of wall thickness, surface finish (black, galvanized, or painted), or end finish (plain end, beveled end, threaded and coupled). These pipes and tubes are generally known as standard pipes and tubes and are intended for the low pressure conveyance of water, steam, natural gas, and other liquids and gasses in plumbing and heating systems, air conditioning units, automatic sprinkler systems, and other related uses, and generally meets ASTM A–53 specifications. Standard pipe may also be used for light load-bearing applications, such as for fence tubing, and as structural pipe tubing used for farming and support members for reconstruction or load bearing purposes in the construction, shipbuilding, trucking, farm equipment, and related industries. Unfinished conduit pipe is also included in the orders.
All carbon steel pipes and tubes within the physical description outlined above are included within the scope of the orders, except line pipe, oil country tubular goods, boiler tubing, mechanical tubing, pipe and tube hollows for redraws, finished scaffolding, and finished conduit. Standard pipe that is dual or triple certified/stenciled that enters the U.S. as line pipe of a kind used for oil or gas pipelines is also not included in the orders.
Imports of the products covered by the orders are currently classifiable under the following HTSUS subheadings: 7306.30.10.00, 7306.30.50.25, 7306.30.50.32, 73.06.30.50.40, 7306.30.50.55, 7306.30.50.85, and 7306.30.50.90. Although the HTSUS subheadings are provided for convenience and customs purposes, our written description of the scope of the orders is dispositive.
The products covered by the order are (1) circular welded non-alloy steel pipes and tubes, of circular cross section over 114.3 millimeters (4.5 inches), but not over 406.4 millimeters (16 inches) in outside diameter, with a wall thickness of 1.65 millimeters (0.065 inches) or more, regardless of surface finish (black, galvanized, or painted), or end-finish (plain end, beveled end, threaded, or threaded and coupled); and (2) circular welded non-alloy steel pipes and tubes, of circular cross-section less than 406.4 millimeters (16 inches), with a wall thickness of less than 1.65 millimeters (0.065 inches), regardless of surface finish (black, galvanized, or painted) or end-finish (plain end, beveled end, threaded, or threaded and coupled). These pipes and tubes are generally known as standard pipes and tubes and are intended for the low pressure conveyance of water, steam, natural gas, air, and other liquids and gases in plumbing and heating systems, air conditioning units, automatic sprinkling systems, and other related uses, and generally meet ASTM A–53 specifications. Standard pipe may also be used for light load-bearing applications, such as for fence-tubing and as structural pipe tubing used for framing and support members for construction, or load-bearing purposes in the construction, shipbuilding, trucking, farm-equipment, and related industries. Unfinished conduit pipe is also included in the order.
All carbon steel pipes and tubes within the physical description outlined above are included within the scope of the order, except line pipe, oil country tubular goods, boiler tubing, mechanical tubing, pipe and tube hollows for redraws, finished scaffolding, and finished conduit. Standard pipe that is dual or triple certified/stenciled that enters the U.S. as line pipe of a kind or used for oil and gas pipelines is also not included in the scope of the order.
Imports of the products covered by the order are currently classifiable under the following HTSUS subheadings, 7306.30.10.00, 7306.30.50.85, 7306.30.50.90. Although the HTSUS subheadings are provided for convenience and customs purposes, our written description of the scope of the order is dispositive.
The products covered by the order are certain circular welded carbon steel pipes and tubes from Taiwan, which are defined as: welded carbon steel pipes and tubes, of circular cross section, with walls not thinner than 0.065 inch, and 0.375 inch or more but not over 4.5 inches in outside diameter, currently classified under HTSUS item numbers 7306.30.50.25, 7306.30.50.32, 7306.30.50.40, and 7306.30.50.55. Although the HTSUS subheadings are provided for convenience and customs purposes, the written description of the merchandise covered by the order is dispositive.