Skip to Content
Rule

Defense Federal Acquisition Regulation Supplement; Contract Drawings, Maps, and Specifications

Action

Final Rule.

Summary

The Director of Defense Procurement has issued a final rule amending the Defense Federal Acquisition Regulation Supplement (DFARS) to revise a clause used in construction contracts. The revised clause explicitly allows the Government to furnish drawings and specifications to construction contractors in electronic form and requires construction contractors to reproduce and print contract drawings and specifications as needed.

 

Table of Contents Back to Top

EFFECTIVE DATE: Back to Top

August 17, 2000.

FOR FURTHER INFORMATION CONTACT: Back to Top

Ms. Amy Williams, Defense Acquisition Regulations Council, OUSD(ATL)DP(DAR), IMD 3D139, 3062 Defense Pentagon, Washington, DC 20301-3062. Telephone (703) 602-0288; telefax (703) 602-0350. Please cite DFARS Case 99-D025.

SUPPLEMENTARY INFORMATION: Back to Top

A. Background Back to Top

DoD uses the clause at DFARS 252.236-7001, Contract Drawings, Maps, and Specifications, in fixed-price construction contracts. The clause previously stated that the Government will provide five sets (unless another quantity is specified) of large-scale drawings and specifications to the contractor without charge; or, at the Government's option, may furnish the contractor with one set of reproducibles, or half-size drawings. This rule revises the clause to specify that the Government will provide one set of drawings and specifications to the contractor in electronic or paper media, as chosen by the contracting officer, and that the contractor will reproduce and print contract drawings and specifications as needed. In addition, the rule removes the term “maps” from the clause title, since the text of the clause does not contain this term.

DoD published a proposed rule at 65 FR 6574 on February 10, 2000. Three sources submitted comments on the proposed rule. DoD considered all comments in the development of the final rule.

This rule was not subject to Office of Management and Budget review under Executive Order 12866, dated September 30, 1993.

B. Regulatory Flexibility Act Back to Top

DoD certifies that this final rule will not have a significant economic impact on a substantial number of small entities within the meaning of the Regulatory Flexibility Act, 5 U.S.C. 601, et seq., because reproducing and printing contract drawings and specifications normally does not constitute a significant expense, and the contractor can pass this expense along to the Government as part of the contract price.

C. Paperwork Reduction Act Back to Top

The Paperwork Reduction Act does not apply because the rule does not impose any information collection requirements that require the approval of the Office of Management and Budget under 44 U.S.C. 3501, et seq.

List of Subjects in 48 CFR Part 252 Back to Top

Michele P. Peterson,

Executive Editor, Defense Acquisition Regulations Council.

begin regulatory text

Therefore, 48 CFR Part 252 is amended as follows:

1.The authority citation for 48 CFR Part 252 continues to read as follows:

Authority:

41 U.S.C. 421 and 48 CFR Chapter 1.

PART 252—SOLICITATION PROVISIONS AND CONTRACT CLAUSES Back to Top

2.Section 252.236-7001 is revised to read as follows:

252.236-7001 Contract Drawings and Specifications.

As prescribed in 236.570(a), use the following clause:

Contract Drawings and Specifications (Aug 2000) Back to Top

(a) The Government will provide to the Contractor, without charge, one set of contract drawings and specifications, except publications incorporated into the technical provisions by reference, in electronic or paper media as chosen by the Contracting Officer.

(b) The Contractor shall—

(1) Check all drawings furnished immediately upon receipt;

(2) Compare all drawings and verify the figures before laying out the work;

(3) Promptly notify the Contracting Officer of any discrepancies;

(4) Be responsible for any errors that might have been avoided by complying with this paragraph (b); and

(5) Reproduce and print contract drawings and specifications as needed.

(c) In general—

(1) Large-scale drawings shall govern small-scale drawings; and

(2) The Contractor shall follow figures marked on drawings in preference to scale measurements.

(d) Omissions from the drawings or specifications or the misdescription of details of work that are manifestly necessary to carry out the intent of the drawings and specifications, or that are customarily performed, shall not relieve the Contractor from performing such omitted or misdescribed details of the work. The Contractor shall perform such details as if fully and correctly set forth and described in the drawings and specifications.

(e) The work shall conform to the specifications and the contract drawings identified on the following index of drawings:

TitleFileDrawing No.

(End of Clause)

end regulatory text

[FR Doc. 00-20959 Filed 8-16-00; 8:45 am]

BILLING CODE 5000-04-M

Site Feedback