Skip to Content

Notice

Certain Tin Mill Products From Japan: Preliminary Results of Changed Circumstances Review

Document Details

Information about this document as published in the Federal Register.

Published Document

This document has been published in the Federal Register. Use the PDF linked in the document sidebar for the official electronic format.

Start Preamble

AGENCY:

Import Administration, International Trade Administration, Department of Commerce.

SUMMARY:

On October 28, 2002, the Department of Commerce (“the Department”) published a notice of initiation of a changed circumstances review with the intent to revoke, in part, the antidumping duty order on certain tin mill products from Japan with respect to certain laminated tin-free steel, as described below. See Certain Tin Mill Products From Japan: Notice of Initiation of Changed Circumstances Antidumping Duty Review, 67 FR 65783 (October 28, 2002) (“Initiation Notice”). In our Initiation Notice we invited interested parties to comment. On October 29, 2002, Nippon Steel Corporation (“NSC”) filed a letter on behalf of Ohio Coatings Company (“Ohio Coatings”) stating that Ohio Coatings does not oppose the exclusion of certain laminated tin-free steel from the antidumping duty order. We now preliminarily revoke this order, in part, with respect to future entries of certain laminated tin-free steel described below, based on the fact that domestic parties have expressed no interest in the continuation of the order with respect to certain laminated tin-free steel.

EFFECTIVE DATE:

December 17, 2002.

Start Further Info

FOR FURTHER INFORMATION CONTACT:

Michael Ferrier, Import Administration, International Trade Administration, U.S. Department of Commerce, 14th Street and Constitution Avenue, NW., Washington, DC 20230; telephone: (202) 482-1394.

The Applicable Statute and Regulations

Unless otherwise indicated, all citations to the statute are references to the provisions effective January 1, 1995, the effective date of the amendments made to the Tariff Act of 1930, as amended (“the Act”), by the Uruguay Round Agreements Act. In addition, unless otherwise indicated, all citations to the Department's regulations are to the regulations as codified at 19 CFR part 351 (2002).

End Further Info End Preamble Start Supplemental Information

SUPPLEMENTARY INFORMATION:

Background

On August 28, 2000, the Department published in the Federal Register the antidumping duty order on certain tin Start Printed Page 77228mill products from Japan. See Notice of Antidumping Duty Order: Certain Tin Mill Products from Japan 65 FR 52067 (August 28, 2000) (TMP Order). On September 6, 2002, Nippon Steel Corporation (“Nippon”), an exporter and manufacturer of the subject merchandise requested that the Department revoke, in part, the antidumping duty order on certain tin mill products from Japan. Specifically, Nippon requested that the Department revoke the order with respect to imports meeting the following specifications: Tin-free steel laminated on one or both sides of the surface with a polyester film, consisting of two layers (an amorphous layer and an outer crystal layer), that contains no more than the indicated amounts of the following environmental hormones: 1 mg/kg BADGE (BisPhenol—A Di-glycidyl Ether), 1 mg/kg BFDGE (BisPhenol—F Di-glycidyl Ether), and 3 mg/kg BPA (BisPhenol—A). Nippon included letters from Weirton Steel Corporation, United States Steel Corporation, Bethlehem Steel Corporation, USS-Posco Industries, and National Steel Corporation, in its request for the changed circumstances review stating their support for the exclusion of the laminated tin-free steel, as described above. However, the Department had no information on the record that these domestic producers of tin mill products, account for substantially all, or at least 85 percent, of the production of the domestic like product (See Oil Country Tubular Goods From Mexico: Preliminary Results of Changed Circumstances Antidumping Duty Administrative Review, 64 FR 14213 (March 24, 1999). Therefore, we did not combine this initiation with the preliminary determination, which is our normal practice under section 351.221(c)(3)(ii) of the Department's regulations.

On October 28, 2002, the Department published a notice of initiation of a changed circumstances review of the antidumping duty order on certain tin mill products from Japan with respect to certain laminated tin-free steel. See Initiation Notice. In the Initiation Notice, we indicated that interested parties could submit comments for consideration in the Department's preliminary results not later than 14 days after publication of the initiation of the review, and submit responses to those comments no later than 7 days following the submission of comments. On October 29, 2002, Nippon filed a letter on behalf of Ohio Coatings stating that Ohio Coatings does not oppose the exclusion of certain laminated tin-free steel from the antidumping duty order on tin mill products from Japan. We did not receive any other comments, nor any rebuttal comments.

Scope of Review

The products covered by this antidumping order are tin mill flat-rolled products that are coated or plated with tin, chromium or chromium oxides. Flat-rolled steel products coated with tin are known as tin plate. Flat-rolled steel products coated with chromium or chromium oxides are known as tin-free steel or electrolytic chromium-coated steel. The scope includes all the noted tin mill products regardless of thickness, width, form (in coils or cut sheets), coating type (electrolytic or otherwise), edge (trimmed, untrimmed or further processed, such and scroll cut), coating thickness, surface finish, temper, coating metal (tin, chromium, chromium oxide), reduction (single- or double-reduced), and whether or not coated with a plastic material. All products that meet the written physical description are within the scope of this order unless specifically excluded. The following products, by way of example, are outside and/or specifically excluded from the scope of this order:

—Single reduced electrolytically chromium coated steel with a thickness 0.238 mm (85 pound base box) (#10%) or 0.251 mm (90 pound base box) (#10%) or 0.255 mm (#10%) with 770 mm (minimum width) (#1.588 mm) by 900 mm (maximum length if sheared) sheet size or 30.6875 inches (minimum width) (# 1/16 inch) and 35.4 inches (maximum length if sheared) sheet size; with type MR or higher (per ASTM) A623 steel chemistry; batch annealed at T2 1/2 anneal temper, with a yield strength of 31 to 42 kpsi (214 to 290 Mpa); with a tensile strength of 43 to 58 kpsi (296 to 400 Mpa); with a chrome coating restricted to 32 to 150 mg/m2; with a chrome oxide coating restricted to 6 to 25 mg/m2 with a modified 7B ground roll finish or blasted roll finish; with roughness average (Ra) 0.10 to 0.35 micrometers, measured with a stylus instrument with a stylus radius of 2 to 5 microns, a trace length of 5.6 mm, and a cut-off of 0.8 mm, and the measurement traces shall be made perpendicular to the rolling direction; with an oil level of 0.17 to 0.37 grams/base box as type BSO, or 2.5 to 5.5 mg/m2 as type DOS, or 3.5 to 6.5 mg/m2 as type ATBC; with electrical conductivity of static probe voltage drop of 0.46 volts drop maximum, and with electrical conductivity degradation to 0.70 volts drop maximum after stoving (heating to 400 degrees F for 100 minutes followed by a cool to room temperature).

—Single reduced electrolytically chromium- or tin-coated steel in the gauges of 0.0040 inch nominal, 0.0045 inch nominal, 0.0050 inch nominal, 0.0061 inch nominal (55 pound base box weight), 0.0066 inch nominal (60 pound base box weight), and 0.0072 inch nominal (65 pound base box weight), regardless of width, temper, finish, coating or other properties.

—Single reduced electrolytically chromium coated steel in the gauge of 0.024 inch, with widths of 27.0 inches or 31.5 inches, and with T-1 temper properties.

—Single reduced electrolytically chromium coated steel, with a chemical composition of 0.005% max carbon, 0.030% max silicon, 0.25% max manganese, 0.025% max phosphorous, 0.025% max sulfur, 0.070% max aluminum, and the balance iron, with a metallic chromium layer of 70-130 mg/m2, with a chromium oxide layer of 5-30 mg/m2, with a tensile strength of 260-440 N/mm2, with an elongation of 28-48%, with a hardness (HR-30T) of 40-58, with a surface roughness of 0.5-1.5 microns Ra, with magnetic properties of Bm (KG)10.0 minimum, Br (KG) 8.0 minimum, Hc (Oe) 2.5-3.8, and MU 1400 minimum, as measured with a Riken Denshi DC magnetic characteristic measuring machine, Model BHU-60.

—Bright finish tin-coated sheet with a thickness equal to or exceeding 0.0299 inch, coated to thickness of 3/4 pound (0.000045 inch) and 1 pound (0.00006 inch).

—Electrolytically chromium coated steel having ultra flat shape defined as oil can maximum depth of 5/64 inch (2.0 mm) and edge wave maximum of 5/64 inch (2.0 mm) and no wave to penetrate more than 2.0 inches (51.0 mm) from the strip edge and coilset or curling requirements of average maximum of 5/64 inch (2.0 mm) (based on six readings, three across each cut edge of a 24 inches (61 cm) long sample with no single reading exceeding 4/32 inch (3.2 mm) and no more than two readings at 4/32 inch (3.2 mm)) and (for 85 pound base box item only: crossbuckle maximums of 0.001 inch (0.0025 mm) average having no reading above 0.005 inch (0.127 mm)), with a camber maximum of 1/4 inch (6.3 mm) per 20 feet (6.1 meters), capable of being bent 120 degrees on a 0.002 inch radius without cracking, with a chromium Start Printed Page 77229coating weight of metallic chromium at 100 mg/m2 and chromium oxide of 10 mg/m2, with a chemistry of 0.13% maximum carbon, 0.60% maximum manganese, 0.15% maximum silicon, 0.20% maximum copper, 0.04% maximum phosphorous, 0.05% maximum sulfur, and 0.20% maximum aluminum, with a surface finish of Stone Finish 7C, with a DOS-A oil at an aim level of 2 mg/square meter, with not more than 15 inclusions/foreign matter in 15 feet (4.6 meters) (with inclusions not to exceed 1/32 inch (0.8 mm) in width and 3/64 inch (1.2 mm) in length), with thickness/temper combinations of either 60 pound base box (0.0066 inch) double reduced CADR8 temper in widths of 25.00 inches, 27.00 inches, 27.50 inches, 28.00 inches, 28.25 inches, 28.50 inches, 29.50 inches, 29.75 inches, 30.25 inches, 31.00 inches, 32.75 inches, 33.75 inches, 35.75 inches, 36.25 inches, 39.00 inches, or 43.00 inches, or 85 pound base box (0.0094 inch) single reduced CAT4 temper in widths of 25.00 inches, 27.00 inches, 28.00 inches, 30.00 inches, 33.00 inches, 33.75 inches, 35.75 inches, 36.25 inches, or 43.00 inches, with width tolerance of #1/8 inch, with a thickness tolerance of #0.0005 inch, with a maximum coil weight of 20,000 pounds (9071.0 kg), with a minimum coil weight of 18,000 pounds (8164.8 kg) with a coil inside diameter of 16 inches (40.64 cm) with a steel core, with a coil maximum outside diameter of 59.5 inches (151.13 cm), with a maximum of one weld (identified with a paper flag) per coil, with a surface free of scratches, holes, and rust.

—Electrolytically tin coated steel having differential coating with 1.00 pound/base box equivalent on the heavy side, with varied coating equivalents in the lighter side (detailed below), with a continuous cast steel chemistry of type MR, with a surface finish of type 7B or 7C, with a surface passivation of 0.7 mg/square foot of chromium applied as a cathodic dichromate treatment, with coil form having restricted oil film weights of 0.3-0.4 grams/base box of type DOS-A oil, coil inside diameter ranging from 15.5 to 17 inches, coil outside diameter of a maximum 64 inches, with a maximum coil weight of 25,000 pounds, and with temper/coating/dimension combinations of : (1) CAT 4 temper, 1.00/.050 pound/base box coating, 70 pound/base box (0.0077 inch) thickness, and 33.1875 inch ordered width; or (2) CAT5 temper, 1.00/0.50 pound/base box coating, 75 pound/base box (0.0082 inch) thickness, and 34.9375 inch or 34.1875 inch ordered width; or (3) CAT5 temper, 1.00/0.50 pound/base box coating, 107 pound/base box (0.0118 inch) thickness, and 30.5625 inch or 35.5625 inch ordered width; or (4) CADR8 temper, 1.00/0.50 pound/base box coating, 85 pound/base box (0.0093 inch) thickness, and 35.5625 inch ordered width; or (5) CADR8 temper, 1.00/0.25 pound/base box coating, 60 pound/base box (0.0066 inch) thickness, and 35.9375 inch ordered width; or (6) CADR8 temper, 1.00/0.25 pound/base box coating, 70 pound/base box (0.0077 inch) thickness, and 32.9375 inch, 33.125 inch, or 35.1875 inch ordered width.

—Electrolytically tin coated steel having differential coating with 1.00 pound/base box equivalent on the heavy side, with varied coating equivalents on the lighter side (detailed below), with a continuous cast steel chemistry of type MR, with a surface finish of type 7B or 7C, with a surface passivation of 0.5 mg/square foot of chromium applied as a cathodic dichromate treatment, with ultra flat scroll cut sheet form, with CAT 5 temper with 1.00/0.10 pound/base box coating, with a lithograph logo printed in a uniform pattern on the 0.10 pound coating side with a clear protective coat, with both sides waxed to a level of 15-20 mg/216 sq. in., with ordered dimension combinations of (1) 75 pound/base box (0.0082 inch) thickness and 34.9375 inch × 31.748 inch scroll cut dimensions; or (2) 75 pound/base box (0.0082 inch) thickness and 34.1875 inch × 29.076 inch scroll cut dimensions; or (3) 107 pound/base box (0.0118 inch) thickness and 30.5625 inch × 34.125 inch scroll cut dimension.

—Tin-free steel coated with a metallic chromium layer between 100-200 mg/m2 and a chromium oxide layer between 5-30 mg/m2; chemical composition of 0.05% maximum carbon, 0.03% maximum silicon, 0.60% maximum manganese, 0.02% maximum phosphorous, and 0.02% maximum sulfur; magnetic flux density (“Br”) of 10 kg minimum and a coercive force (“Hc”) of 3.8 Oe minimum.

The merchandise subject to this order is classified in the Harmonized Tariff Schedule of the United States (“HTSUS”), under HTSUS subheadings 7210.11.0000, 7210.12.0000, 7210.50.0000, 7212.10.0000, and 7212.50.0000 if of non-alloy steel and under HTSUS subheadings 7225.99.0090, and 7226.99.0000 if of alloy steel. Although the subheadings are provided for convenience and Customs purposes, our written description of the scope of this review is dispositive.

Preliminary Results of Review and Intent to Revoke in Part the Antidumping Duty Order

Pursuant to sections 751(d)(1) of the Act, the Department may revoke an antidumping or countervailing duty order, in whole or in part, based on a review under section 751(b) of the Act (i.e., a changed circumstances review). Section 751(b)(1) of the Act requires a changed circumstances review to be conducted upon receipt of a request which shows changed circumstances sufficient to warrant a review. Section 351.222(g) of the Department's regulations provides that the Department will conduct a changed circumstances administrative review under 19 CFR 351.216, and may revoke an order (in whole or in part), if it determines that (i) producers accounting for substantially all of the production of the domestic like product to which the order pertains have expressed a lack of interest in the relief provided by the order, in whole or in part, or (ii) if other changed circumstances sufficient to warrant revocation exist. Since the Department did not receive any comments during the comment period opposing the exclusion of certain laminated tin-free steel from the antidumping duty order, the Department is preliminarily revoking the order on certain tin mill products from Japan, in part, for all future entries with regard to the products which meet the specifications above.

Interested parties wishing to comment on these results may submit briefs to the Department no later than 14 days after the publication of this notice in the Federal Register. Parties will have five days subsequent to this due date to submit rebuttal comments, limited to the issues raised in those comments. Parties who submit comments or rebuttal comments in this proceeding are requested to submit with the argument (1) a statement of the issue and (2) a brief summary of the argument (no longer than five pages, including footnotes). Any requests for hearing must be filed within 14 days of the publication of this notice in the Federal Register.

All written comments must be submitted in accordance with 19 CFR 351.303, and must be served on all interested parties on the Department's service list. The Department will also Start Printed Page 77230issue its final results of review within 270 days after the date on which the changed circumstances review is initiated, in accordance with 19 CFR 351.216(e), and will publish these results in the Federal Register. While the changed circumstances review is underway, the current requirement for a cash deposit of estimated antidumping duties on all subject merchandise, including the merchandise that is the subject of this changed circumstances review, will continue unless and until it is modified pursuant to the final results of this changed circumstances review or an administrative review.

This notice is in accordance with sections 751(b)(1) and 777(i)(1) of the Act and 19 CFR 351.216 and 351.222 of the Department's regulations.

Start Signature

Dated: December 10, 2002.

Faryar Shirzad,

Assistant Secretary for Import Administration.

End Signature End Supplemental Information

[FR Doc. 02-31626 Filed 12-16-02; 8:45 am]

BILLING CODE 3510-DS-P