This site displays a prototype of a “Web 2.0” version of the daily Federal Register. It is not an official legal edition of the Federal Register, and does not replace the official print version or the official electronic version on GPO’s govinfo.gov.
The documents posted on this site are XML renditions of published Federal Register documents. Each document posted on the site includes a link to the corresponding official PDF file on govinfo.gov. This prototype edition of the daily Federal Register on FederalRegister.gov will remain an unofficial informational resource until the Administrative Committee of the Federal Register (ACFR) issues a regulation granting it official legal status. For complete information about, and access to, our official publications and services, go to About the Federal Register on NARA's archives.gov.
The OFR/GPO partnership is committed to presenting accurate and reliable regulatory information on FederalRegister.gov with the objective of establishing the XML-based Federal Register as an ACFR-sanctioned publication in the future. While every effort has been made to ensure that the material on FederalRegister.gov is accurately displayed, consistent with the official SGML-based PDF version on govinfo.gov, those relying on it for legal research should verify their results against an official edition of the Federal Register. Until the ACFR grants it official status, the XML rendition of the daily Federal Register on FederalRegister.gov does not provide legal notice to the public or judicial notice to the courts.
National Highway Traffic Safety Administration, DOT.
Notice of receipt of petition for decision that nonconforming passenger cars are eligible for importation.
This document announces receipt by the National Highway Traffic Safety Administration (NHTSA) of a petition for a decision that 1989 Volkswagen Golf Rallye passenger cars that were not originally manufactured to comply with all applicable Federal motor vehicle safety standards are eligible for importation into the United States because (1) they are substantially similar to vehicles that were originally manufactured for sale in the United States and that were certified by their manufacturer as complying with the safety standards, and (2) they are capable of being readily altered to conform to the standards.
The closing date for comments on the petition is April 22, 2005.
Comments should refer to the docket number and notice number, and be submitted to: Docket Management, Room PL-401, 400 Seventh St., SW., Washington, DC 20590. (Docket hours are from 9 a.m. to 5 p.m.) Anyone is able to search the electronic form of all comments received into any of our dockets by the name of the individual submitting the comment (or signing the comment, if submitted on behalf of an association, business, labor union, etc.). You may review DOT's complete Privacy Act Statement in the Federal Register published on April 11, 2000 (Volume 65, Number 70; Pages 19477-78), or you may visit http://dms.dot.gov.Start Further Info
FOR FURTHER INFORMATION CONTACT:
Coleman Sachs, Office of Vehicle Safety Compliance, NHTSA (202) 366-3151.End Further Info End Preamble Start Supplemental Information
Under 49 U.S.C. 30141(a)(1)(A), a motor vehicle that was not originally manufactured to conform to all applicable Federal motor vehicle safety standards shall be refused admission into the United States unless NHTSA has decided that the motor vehicle is substantially similar to a motor vehicle originally manufactured for importation into and sale in the United States, certified under 49 U.S.C. 30115, and of the same model year as the model of the motor vehicle to be compared, and is capable of being readily altered to conform to all applicable Federal motor vehicle safety standards.
Petitions for eligibility decisions may be submitted by either manufacturers or importers who have registered with NHTSA pursuant to 49 CFR part 592. As specified in 49 CFR 593.7, NHTSA publishes notice in the Federal Register of each petition that it receives, and affords interested persons an opportunity to comment on the petition. At the close of the comment period, NHTSA decides, on the basis of the petition and any comments that it has received, whether the vehicle is eligible for importation. The agency then publishes this decision in the Federal Register.
US SPECS of Aberdeen, Maryland (Registered Importer 03-321) has petitioned NHTSA to decide whether nonconforming 1989 Volkswagen Golf Rallye passenger cars are eligible for importation into the United States. The vehicles which US SPECS believes are substantially similar are 1989 Volkswagen Golf passenger cars that were manufactured for sale in the United States and certified by their manufacturer as conforming to all applicable Federal motor vehicle safety standards.
The petitioner claims that it carefully compared non-U.S. certified 1989 Volkswagen Golf Rallye passenger cars to their U.S.-certified counterparts, and found the vehicles to be substantially similar with respect to compliance with most Federal motor vehicle safety standards.
US SPECS submitted information with its petition intended to demonstrate that non-U.S. certified 1989 Volkswagen Golf Rallye passenger cars, as originally manufactured, conform to many Federal motor vehicle safety standards in the same manner as their U.S. certified counterparts, or are capable of being readily altered to conform to those standards.
Specifically, the petitioner claims that non-U.S. certified 1989 Volkswagen Golf Rallye passenger cars are identical to their U.S. certified counterparts with respect to compliance with Standard Nos. 102 Transmission Shift Lever Sequence, Starter Interlock, and Transmission Braking Effect, 103 Windshield Defrosting and Defogging Systems, 104 Windshield Wiping and Washing Systems, 105 Hydraulic Brake Systems, 106 Brake Hoses, 107 Reflecting Surfaces, 109 New Pneumatic Tires, 112 HeadLamp Concealment Devices, 113 Hood Latch System, 116 Motor Vehicle Brake Fluids, 124 Accelerator Control Systems, 201 Occupant Protection in Interior Impact, 202 Head Restraints, 204 Steering Control Rearward Displacement, 205 Glazing Materials, 206 Door Locks and Door Retention Components, 207 Seating Systems, 211 Wheel Nuts, Wheel Discs and Hub Caps, 212 Windshield Mounting, 216 Roof Crush Resistance, 219 Windshield Zone Intrusion, and 302 Flammability of Interior Materials.
The petitioner also contends that the vehicles are capable of being readily altered to meet the following standards, in the manner indicated:
Standard No. 101 Controls and Displays: (a) Installation of an indicator lamp lens cover inscribed with the word “brake” in the instrument cluster in place of the one inscribed with the international ECE warning symbol; and (b) replacement or conversion of the speedometer to read in miles per hour.
Standard No. 108 Lamps, Reflective Devices and Associated Equipment: Inspection of all vehicles and installation, on vehicles that are not already so equipped, of U.S.-model: (a) Headlamp assemblies; (b) front side marker lamps; (c) taillamp assemblies that incorporate rear side marker lamps; (d) rear high mounted stop lamp; and (e) front and rear side reflex reflectors.
Standard No. 110 Tire Selection and Rims: Installation of a tire information placard.
Standard No. 111 Rearview Mirrors: Installation of a U.S.-model passenger side rearview mirror, or inscription of the required warning statement on the face of that mirror.
Standard No. 114 Theft Protection: Installation a supplemental warning buzzer to meet the requirements of this standard.
Standard No. 115 Vehicle Identification: Installation of a vehicle identification plate near the left Start Printed Page 14752windshield post to meet the requirements of this standard.
Standard No. 118 Power-Operated Window, Partition, and Roof Panel Systems: Inspection of all vehicles and rewiring the vehicle's systems, as required, to ensure compliance with the requirements of the standard.
Standard No. 208 Occupant Crash Protection: Installation, on vehicles that are not already so equipped, of: (a) Seat belt warning buzzer and warning light systems wired to the seat belt latch; (b) U.S.-model knee bolsters; and (c) U.S.-model door-anchored automatic shoulder belts at front outboard seating positions on vehicles manufactured on or after September 1, 1989.
The petitioner also states that the vehicles are equipped with combination lap and shoulder belts at the outboard front and seating positions. These seat belts are self-tensioning and capable of being released by means of a single red push button.
Standard No. 209 Seat Belt Assemblies: Inspection of all vehicles and installation of U.S.-model seat belt assemblies on vehicles that are not already so equipped.
Standard No. 210 Seat Belt Assembly Anchorages: Inspection of all vehicles and replacement of any non-U.S.-model seat belt anchorages with U.S.-model components on vehicles that are not already so equipped.
Standard No. 214 Side Impact Protection: Inspection of all vehicles and installation of U.S.-model door reinforcements on vehicles that are not already so equipped.
Standard No. 301 Fuel System Integrity: Inspection of all vehicles and installation of U.S.-model fuel system components on vehicles that are not already so equipped.
In addition, inspection of all vehicles and installation of U.S.-model bumper and bumper support structure components, on vehicles that are not already so equipped, to ensure compliance with the requirements of the Bumper Standard found in 49 CFR part 581.
Interested persons are invited to submit comments on the petition described above. Comments should refer to the docket number and be submitted to: Docket Management, Room PL-401, 400 Seventh St., SW., Washington, DC 20590. (Docket hours are from 9 a.m. to 5 p.m.) It is requested but not required that 10 copies be submitted.
All comments received before the close of business on the closing date indicated above will be considered, and will be available for examination in the docket at the above address both before and after that date. To the extent possible, comments filed after the closing date will also be considered. Notice of final action on the petition will be published in the Federal Register pursuant to the authority indicated below.Start Signature
Claude H. Harris,
Director, Office of Vehicle Safety Compliance.
[FR Doc. 05-5762 Filed 3-22-05; 8:45 am]
BILLING CODE 4910-59-P