Federal Aviation Administration (FAA), Department of Transportation (DOT).
The FAA is adopting a new airworthiness directive (AD) for certain Airbus Model A320-111 airplanes and Model A320-200 series airplanes. This AD requires installing a bonding strip between each of the two water scavenge jet pumps of the center fuel tank and the rear spar in section 21. This AD results from the results of fuel system reviews conducted by the manufacturer. We are issuing this AD to prevent an ignition source for fuel vapor in the wing, which could result in fire or explosion in the center wing fuel tank.
This AD becomes effective October 26, 2005.
The Director of the Federal Register approved the incorporation by reference of a certain publication listed in the AD as of October 26, 2005.
You may examine the AD docket on the Internet at http://dms.dot.gov or in person at the Docket Management Facility, U.S. Department of Transportation, 400 Seventh Street SW., Nassif Building, Room PL-401, Washington, DC.
Contact Airbus, 1 Rond Point Maurice Bellonte, 31707 Blagnac Cedex, France, for service information identified in this AD.Start Further Info
FOR FURTHER INFORMATION CONTACT:
Dan Rodina, Aerospace Engineer, International Branch, ANM-116, FAA, Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, Washington 98055-4056; telephone (425) 227-2125; fax (425) 227-1149.End Further Info End Preamble Start Supplemental Information
Examining the Docket
You may examine the airworthiness directive (AD) docket on the Internet at http://dms.dot.gov or in person at the Docket Management Facility office between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The Docket Management Facility office (telephone (800) 647-5227) is located on the plaza level of the Nassif Building at the street address stated in the ADDRESSES section.
The FAA issued a notice of proposed rulemaking (NPRM) to amend 14 CFR part 39 to include an AD that would apply to certain Airbus Model A320-111 airplanes and Model A320-200 series airplanes. That NPRM was published in the Federal Register on July 19, 2005 (70 FR 41350). That NPRM proposed to require installing a bonding strip between each of the two water scavenge jet pumps of the center fuel tank and the rear spar in section 21.
We provided the public the opportunity to participate in the development of this AD. We have considered the comment received. The commenter supports the NPRM.
We have carefully reviewed the available data, including the comment received, and determined that air safety and the public interest require adopting the AD as proposed.
Costs of Compliance
This AD will affect about 371 airplanes of U.S. registry. The actions will take about 1 work hour per airplane, at an average labor rate of $65 per work hour. The manufacturer will supply required parts at no charge. Based on these figures, the estimated cost of the AD for U.S. operators is $24,115, or $65 per airplane.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, Section 106, describes the authority of the FAA Administrator. Subtitle VII, Aviation Programs, describes in more detail the scope of the Agency's authority.
We are issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section 44701, “General requirements.” Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.
We have determined that this AD will not have federalism implications under Executive Order 13132. This AD will not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government.
For the reasons discussed above, I certify that this AD:
(1) Is not a “significant regulatory action” under Executive Order 12866;
(2) Is not a “significant rule” under DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and
(3) Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.
We prepared a regulatory evaluation of the estimated costs to comply with this AD and placed it in the AD docket. See the ADDRESSES section for a location to examine the regulatory evaluation.Start List of Subjects
List of Subjects in 14 CFR Part 39
- Air transportation
- Aviation safety
- Incorporation by reference
Adoption of the AmendmentStart Amendment Part
Accordingly, under the authority delegated to me by the Administrator, the FAA amends 14 CFR part 39 as follows:End Amendment Part Start Part
PART 39—AIRWORTHINESS DIRECTIVESEnd Part Start Amendment Part
1. The authority citation for part 39 continues to read as follows:End Amendment Part
2. The Federal Aviation Administration (FAA) amends § 39.13 by adding the following new airworthiness directive (AD):End Amendment Part
2005-19-16 Airbus: Amendment 39-14281. Docket No. FAA-2005-21861; Directorate Identifier 2005-NM-093-AD.
(a) This AD becomes effective October 26, 2005.
(c) This AD applies to Airbus Model A320-111, -211, -212, -214, -231, -232, and -233 airplanes, certificated in any category; except those airplanes on which Airbus Modification 25513 has been accomplished in production.
(d) This AD results from fuel system reviews conducted by the manufacturer. We are issuing this AD to prevent an ignition source for fuel vapor in the wing, which could result in fire or explosion in the adjacent wing fuel tank.
(e) You are responsible for having the actions required by this AD performed within the compliance times specified, unless the actions have already been done.
Installation of Bonding Strips
(f) Within 56 months after the effective date of this AD, install a bonding strip between each of the two water scavenge jet pumps of the center fuel tank and the rear spar in section 21, in accordance with the Accomplishment Instructions of Airbus Service Bulletin A320-28-1067, Revision 02, dated January 27, 1997.
Alternative Methods of Compliance (AMOCs)
(g) The Manager, International Branch, ANM-116, Transport Airplane Directorate, FAA, has the authority to approve AMOCs for this AD, if requested in accordance with the procedures found in 14 CFR 39.19.
(h) French airworthiness directive F-2005-056, dated April 13, 2005, also addresses the subject of this AD.
Material Incorporated by Reference
(i) You must use Airbus Service Bulletin A320-28-1067, Revision 02, dated January 27, 1997, to perform the actions that are required by this AD, unless the AD specifies otherwise. The Director of the Federal Register approved the incorporation by reference of this document in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. Contact Airbus, 1 Rond Point Maurice Bellonte, 31707 Blagnac Cedex, France, for a copy of this service information. You may review copies at the Docket Management Facility, U.S. Department of Transportation, 400 Seventh Street SW., room PL-401, Nassif Building, Washington, DC; on the Internet at http://dms.dot.gov; or at the National Archives and Records Administration (NARA). For information on the availability of this material at the NARA, call (202) 741-6030, or go to http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html.Start Signature
Issued in Renton, Washington, on September 9, 2005.
Kalene C. Yanamura,
Acting Manager, Transport Airplane Directorate, Aircraft Certification Service.
[FR Doc. 05-18520 Filed 9-20-05; 8:45 am]
BILLING CODE 4910-13-P