Consumer Product Safety Commission.
As required by the Paperwork Reduction Act of 1995 (44 U.S.C. Chapter 35), the Consumer Product Safety Commission requests comments on a proposed extension of approval of a collection of information from manufacturers and importers of bicycle helmets. The collection of information is in regulations implementing the Safety Standard for Bicycle Helmets. 16 CFR Part 1203. These regulations establish testing and recordkeeping requirements for manufacturers and importers of bicycle helmets subject to the standard. The Commission will consider all comments received in response to this notice before requesting an extension of approval of this collection of information from the Office of Management and Budget.
Written comments must be received by the Office of the Secretary not later than April 13, 2007.
Written comments should be captioned “Bicycle Helmets” and e-mailed to firstname.lastname@example.org. Comments may also be sent by facsimile to (301) 504-0127, or by mail to the Office of the Secretary, Consumer Product Safety Commission, 4330 East West Highway, Bethesda, Maryland 20814.Start Further Info
FOR FURTHER INFORMATION CONTACT:
For information about the proposed renewal of this collection of information, or to obtain a copy of the pertinent regulations, call or write Linda L. Glatz, Division of Policy and Planning, Office of Information Technology and Technology Services, Consumer Product Safety Commission, 4330 East West Highway, Bethesda, Maryland 20814; (301) 504-7671, or by e-mail to email@example.com.End Further Info End Preamble Start Supplemental Information
In 1994, Congress passed the “Child Safety Protection Act,” which, among other things, included the “Children's Bicycle Helmet Safety Act of 1994” Public Law 103-267, 108 Stat. 726. This law directed the Commission to issue a final standard applicable to bicycle helmets that would replace several existing voluntary standards with a single uniform standard that would include provisions to protect against the risk of helmets coming off the heads of bicycle riders, address the risk of injury to children, and cover other issues as appropriate. The Commission issued the final bicycle helmet standard in 1998. It is codified at 16 CFR Part 1203.
The standard requires all bicycle helmets manufactured after March 10, 1999, to meet impact-attenuation and other requirements. The standard also contains testing and recordkeeping requirements to ensure that bicycle helmets meet the standard's requirements. Certification regulations implementing the standard require manufacturers, importers, and private labelers of bicycle helmets subject to the standard to (1) Perform tests to demonstrate that those products meet the requirements of the standard, (2) maintain records of those tests, and (3) affix durable labels to the helmets stating that the helmet complies with the applicable standard. The certification regulations are codified at 16 CFR Part 1203, Subpart B.
The Commission uses the information compiled and maintained by manufacturers, importers, and private labelers of bicycle helmets subject to the standard to help protect the public from risks of injury or death associated with head injury associated with bicycle riding. More specifically, this information helps the Commission determine whether bicycle helmets subject to the standard comply with all applicable requirements. The Commission also uses this information to obtain corrective actions if bicycle helmets fail to comply with the standard in a manner that creates a substantial risk of injury to the public.
The Office of Management and Budget (OMB) approved the collection of information in the certification regulations under control number 3041-0127. The Commission now proposes to request an extension of approval for the collection of information in the certification regulations.
A. Estimated Burden
The Commission staff estimates that approximately 30 firms manufacture or import bicycle helmets subject to the standard. There are an estimated 200 different models of bicycle helmets currently marketed in the U.S. The Commission staff estimates that the time required to comply with the collection of information requirements is approximately 100 to 150 hours per model per year. The total amount of time estimated for compliance with these requirements will be 20,000 to 30,000 hours per year (200 models × 100-150 hours/model = 20,000-30,000 hours). The annualized cost to respondents for the hour burden for collection of information is $896,000-$1,345,000 based on 20,000-30,000 hours times $44.82/hour (based on total compensation of all civilian workers in managerial and professional positions in the U.S., July 2006, Bureau of Labor Statistics).
B. Request for Comments
The Commission solicits written comments from all interested persons about the proposed collection of information. The Commission specifically solicits information relevant to the following topics:
—Whether the collection of information described above is necessary for the proper performance of the Commission's functions, including whether the information would have practical utility;
—Whether the estimated burden of the proposed collection of information is accurate;
—Whether the quality, utility, and clarity of the information to be collected could be enhanced; and
—Whether the burden imposed by the collection of information could be minimized by use of automated, electronic or other technological collection techniques, or other forms of information technology.Start Signature
Dated: February 7, 2007.
Todd A. Stevenson,
Secretary, Consumer Product Safety Commission.
[FR Doc. E7-2316 Filed 2-9-07; 8:45 am]
BILLING CODE 6355-01-P