Goodyear Tire & Rubber Company (Goodyear), has determined that certain passenger car tires manufactured during the period January 25, 2007, through July 24, 2008, do not fully comply with paragraph S5.5(e) of Federal Motor Vehicle Safety Standards (FMVSS) No. 139, New Pneumatic Radial Tires for Light Vehicles. Goodyear has filed an appropriate report pursuant to 49 CFR Part 573, Defect and Noncompliance Responsibility and Reports.
Pursuant to 49 U.S.C. 30118(d) and 30120(h) and the rule implementing those provisions at 49 CFR Part 556, Goodyear has petitioned for an exemption from the notification and remedy requirements of 49 U.S.C. Chapter 301 on the basis that this noncompliance is inconsequential to motor vehicle safety. Notice of receipt of the petition was published, with a 30-day public comment period, on January 13, 2009, in the Federal Register (74 FR 1760). No comments were received. To view the petition and all supporting documents log onto the Federal Docket Management System Web site at: http://www.regulations.gov/ then follow the online search instructions to locate docket number “NHTSA-2008-0213.”
For further information on this decision, contact Mr. George Gillespie, Office of Vehicle Safety Compliance, the National Highway Traffic Safety Administration (NHTSA), telephone (202) 366-5299, facsimile (202) 366-7002.
Affected are approximately 9,864 size 245/45R17 95H Fierce HP brand passenger car tires manufactured during the period January 25, 2007, through July 24, 2008.
Paragraph S5.5(e) of FMVSS No. 139 requires in pertinent part:
S5.5 Tire markings. Except as specified in paragraphs (a) through (i) of S5.5, each tire must be marked on each sidewall with the information specified in S5.5(a) through (d) and on one sidewall with the information specified in S5.5(e) through (i) according to the phase-in schedule specified in S7 of this standard. The markings must be placed between the maximum section width and the bead on at least one sidewall, unless the maximum section width of the tire is located in an area that is not more than one-fourth of the distance from the bead to the shoulder of the tire. If the maximum section width falls within that area, those markings must appear between the bead and a point one-half the distance from the bead to the shoulder of the tire, on at least one sidewall. The markings must be in letters and numerals not less than 0.078 inches high and raised above or sunk below the tire surface not less than 0.015 inches * * *
(e) The generic name of each cord material used in the plies (both sidewall and tread area) of the tire; * * *
Goodyear explains that the noncompliance is that the sidewall marking incorrectly identifies the generic material of the plies in the body of the tire as Nylon when they are in fact polyester. Specifically, the tires in question were inadvertently manufactured with “Tread: 1 Polyester + 2 Steel Cords + 1 Nylon Cord. The labeling should have been “Tread: 1 Polyester Cord + 2 Steel Cords + 1 Polyester Cord” (emphasis added).
Goodyear states that it discovered the mold labeling error that caused the non-compliance during a routine quality audit.
Goodyear argues that the noncompliance is inconsequential to motor vehicle safety because the tires meet or exceed all applicable Federal Motor Vehicle Safety performance standards. All of the markings related to tire service (load capacity, corresponding inflation pressure, etc.) are correct. The mislabeling of these tires creates no unsafe condition.
Goodyear states that the affected tire molds have been modified and all future production will have the correct material information shown on the sidewall.Start Printed Page 17828
Goodyear also points out that NHTSA has previously granted petitions for sidewall marking noncompliances that it believes are similar to the present noncompliance.
In summation, Goodyear states that it believes that because the noncompliances are inconsequential to motor vehicle safety that no corrective action is warranted.
The agency agrees with Goodyear that the noncompliance is inconsequential to motor vehicle safety. The agency believes that the true measure of inconsequentiality to motor vehicle safety in this case is that there is no effect of the noncompliance on the operational safety of vehicles on which these tires are mounted. The safety of people working in the tire retread, repair, and recycling industries must also be considered. Although tire construction affects the strength and durability, neither the agency nor the tire industry provides information relating tire strength and durability to the number of plies and types of ply cord material in the tread and sidewall. Therefore, tire dealers and customers should consider the tire construction information along with other information such as the load capacity, maximum inflation pressure, and tread wear, temperature, and traction ratings, to assess performance capabilities of various tires. In the agency's judgment, the incorrect labeling of the tire construction information will have an inconsequential effect on motor vehicle safety because most consumers do not base tire purchases or vehicle operation parameters on the ply material in a tire.
The agency also believes the noncompliance will have no measurable effect on the safety of the tire retread, repair, and recycling industries. The use of steel cord construction in the sidewall and tread is the primary safety concern of these industries. In this case, since the tire sidewalls are marked correctly for the number of steel plies, this potential safety concern does not exist.
In consideration of the foregoing, NHTSA has decided that Goodyear has met its burden of persuasion that the subject FMVSS No. 139 labeling noncompliance is inconsequential to motor vehicle safety. Accordingly, Goodyear's petition is granted and the petitioner is exempted from the obligation of providing notification of, and a remedy for, the subject noncompliance under 49 U.S.C. 30118 and 30120.Start Signature
Issued on: April 1, 2010.
Claude H. Harris,
Director, Office of Vehicle Safety Compliance.
[FR Doc. 2010-7874 Filed 4-6-10; 8:45 am]
BILLING CODE 4910-59-P