Skip to Content

Notice

Notice of a Project Waiver of Section 1605 (Buy American Requirement) of the American Recovery and Reinvestment Act of 2009 (ARRA) to the City of Auburn, IN (Auburn)

Document Details

Information about this document as published in the Federal Register.

Published Document

This document has been published in the Federal Register. Use the PDF linked in the document sidebar for the official electronic format.

Start Preamble

AGENCY:

Environmental Protection Agency (EPA).

ACTION:

Notice.

SUMMARY:

The EPA is hereby granting a project waiver of the Buy American requirements of ARRA Section 1605 under the authority of Section 1605(b)(2) [manufactured goods are not produced in the United States of a satisfactory quality] to Auburn, Indiana, for the purchase of three high-speed, high-efficiency magnetic bearing turbo-compressors that will be used in the city's sludge treatment process. This is a project-specific waiver and it only applies to the use of the specified product for the ARRA funded project being proposed. Any other ARRA project that may wish to use the same product must apply for a separate waiver based on project-specific circumstances. These turbo-compressors, which are supplied by ABS USA of Meriden, Connecticut, are manufactured in Sweden, and meet Auburn's performance specifications and requirements. The Acting Regional Administrator is making this determination based on the review and recommendations of EPA Region 5's Water Division. Auburn has provided sufficient documentation to support its request. The Assistant Administrator of the Office of Administration and Resources Management has concurred on this decision to make an exception to Section 1605 of ARRA. This action permits the purchase of high-speed, high-efficiency magnetic bearing turbo-compressors for Auburn's activated sludge project that may otherwise be prohibited under Section 1605(a) of the ARRA.

DATES:

Effective Date: March 25, 2010.

Start Further Info

FOR FURTHER INFORMATION CONTACT:

Andrew Lausted, SRF Program Manager (312) 886-0189, or Puja Lakhani, Office of Regional Counsel, (312) 353-3190, U.S. EPA Region 5, 77 W. Jackson Blvd., Chicago, IL 60604.

End Further Info End Preamble Start Supplemental Information

SUPPLEMENTARY INFORMATION:

In accordance with ARRA Section 1605(c) and pursuant to Section 1605(b)(2) of Public Law 111-5, Buy American requirements, EPA hereby provides notice that it is granting a project waiver to Auburn, Indiana, for the acquisition Start Printed Page 25244of high-speed, high-efficiency magnetic bearing turbo-compressors that are manufactured in Sweden.

Section 1605 of the ARRA requires that none of the appropriated funds may be used for the construction, alteration, maintenance, or repair of a public building or public work unless all of the iron, steel, and manufactured goods used in the project are produced in the United States, or unless a waiver is provided to the recipient by the head of the appropriate agency, here EPA. A waiver may be provided if EPA determines that (1) applying these requirements would be inconsistent with the public interest; (2) iron, steel, and the relevant manufactured goods are not produced in the United States in sufficient and reasonably available quantities and of a satisfactory quality; or (3) inclusion of iron, steel, and the relevant manufactured goods produced in the United States will increase the cost of the overall project by more than 25 percent.

These manufactured goods will provide aeration for Auburn's activated sludge treatment process. The city selected the magnetic bearing technology because of its ability to avoid overheating and its track record of providing long-standing reliable service—key advantages over the competing airfoil bearing technology. Auburn's submissions clearly articulated functional reasons that justified their technical specifications and requirements.

The April 28, 2009 EPA HQ Memorandum, “Implementation of Buy American provisions of Public Law 111-5, the `American Recovery and Reinvestment Act of 2009',” defines reasonably available quantity as “the quantity of iron, steel, or relevant manufactured good is available or will be available at the time needed and place needed, and in the proper form or specification as specified in the project plans and design.”

The applicant met the requirements specified for the availability inquiry as appropriate to the circumstances by conducting an extensive investigation into all possible sources for high-speed, high-efficiency turbo-compressors. Based on the investigation, five companies were found to manufacture these machines, but only two (ABS and one other company) used magnetic bearings. Moreover, both of the companies that use magnetic bearings manufacture their machines overseas. Auburn believes that since ABS has multiple municipal wastewater treatment plant installations in the Midwest and that its competitor has none, that the ABS turbo-compressor technology has been proven and would perform reliably in this specific application. Therefore, Auburn contends that there is no domestic product of satisfactory quality available.

EPA's national contractor prepared a technical assessment report dated January 27, 2010, based on the submitted waiver request. The report determined that the waiver request submittal was complete, that adequate technical information was provided, and that there were no significant weaknesses in the justification provided. Therefore, based on the information provided to EPA and to the best of our knowledge at this time, the high-speed, high-efficiency magnetic bearing turbo-compressors necessary for this project are not manufactured in the United States, and no other U.S. manufactured product can meet Auburn's project performance specifications and requirements.

The purpose of the ARRA is to stimulate economic recovery in part by funding current infrastructure construction, not to delay projects that are “shovel ready” by requiring communities such as Auburn to revise their standards and specifications and to start the bidding process again. The imposition of ARRA Buy American requirements on such projects otherwise eligible for ARRA State Revolving Fund assistance would result in unreasonable delay and thus displace the “shovel ready” status for this project. To further delay project implementation is in direct conflict with a fundamental economic purpose of the ARRA, which is to create or retain jobs.

The State and Tribal Programs Branch has reviewed this waiver request and has determined that the supporting documentation provided by Auburn is sufficient to meet the criteria listed under Section 1605(b) of the ARRA and in the April 28, 2009, “Implementation of Buy American provisions of Public Law 111-5, the `American Recovery and Reinvestment Act of 2009' Memorandum”: Iron, steel, and the manufactured goods are not produced in the United States in sufficient and reasonably available quantities and of a satisfactory quality. The basis for this project waiver is the authorization provided in Section 1605(b)(2) of the ARRA. Due to the lack of production of this item in the United States in sufficient and reasonably available quantities and of a satisfactory quality in order to meet Auburn's project performance specifications and requirements, a waiver from the Buy American requirement is justified.

The March 31, 2009, Delegation of Authority Memorandum provided Regional Administrators with the authority to issue exceptions to Section 1605 of the ARRA within the geographic boundaries of their respective regions and with respect to requests by individual grant recipients. Having established both a proper basis to specify the particular good required for this project, and that this manufactured good was not available from a producer in the United States, Auburn is hereby granted a waiver from the Buy American requirements of Section 1605(a) of Public Law 111-5 for the purchase of high-speed, high efficiency magnetic bearing turbo-compressors using ARRA funds as specified in the community's request of December 21, 2009. This supplementary information constitutes the detailed written justification required by Section 1605(c) for waivers “based on a finding under subsection (b).”

Start Authority

Authority: Pub. L. 111-5, section 1605.

End Authority Start Signature

Dated: March 25, 2010.

Walter W. Kovalick,

Acting Regional Administrator, Region 5.

End Signature End Supplemental Information

[FR Doc. 2010-10918 Filed 5-6-10; 8:45 am]

BILLING CODE 6560-50-P