Occupational Safety and Health Administration (OSHA), Labor.
Request for public comment.
OSHA solicits comments concerning its proposal to extend the Office of Management and Budget's (OMB) approval of the information collection requirements contained in the Welding, Cutting and Brazing Standard (29 CFR part 1910, subpart Q). The information collected is used by employers and workers whenever welding, cutting and brazing are performed. The purpose of the information is to ensure that employers evaluate hazards associated with welding and ensure that adequate measures are taken to make the process safe.
Comments must be submitted (postmarked, sent, or received) by October 25, 2010.
Electronically: You may submit comments and attachments electronically at http://www.regulations.gov, which is the Federal eRulemaking Portal. Follow the instructions online for submitting comments.
Facsimile: If your comments, including attachments, are not longer than 10 pages, you may fax them to the OSHA Docket Office at (202) 693-1648.
Mail, hand delivery, express mail, messenger, or courier service: When using this method, you must submit three copies of your comments and attachments to the OSHA Docket Office, Docket No. OSHA-2010-0037, U.S. Department of Labor, Occupational Safety and Health Administration, Room N-2625, 200 Constitution Avenue, NW., Washington, DC 20210. Deliveries (hand, express mail, messenger, and courier service) are accepted during the Department of Labor's and Docket Office's normal business hours, 8:15 a.m. to 4:45 p.m., e.t.
Instructions: All submissions must include the Agency name and OSHA docket number for the Information Collection Request (ICR) (Docket No. OSHA-2010-0037). All comments, including any personal information you provide, are placed in the public docket without change, and may be made available online at http://www.regulations.gov. For further information on submitting comments see the “Public Participation” heading in the section of this notice titled “Supplementary Information.”
Docket: To read or download comments or other material in the docket, go to http://www.regulations.gov or the OSHA Docket Office at the address above. All documents in the docket (including this Federal Register notice) are listed in the http://www.regulations.gov index; however, some information (e.g., copyrighted material) is not publicly available to read or download through the Web site. All submissions, including copyrighted material, are available for inspection and copying at the OSHA Docket Office. You may also contact Theda Kenney at the address below to obtain a copy of the ICR.Start Further Info
FOR FURTHER INFORMATION CONTACT:
Theda Kenney or Todd Owen, Directorate of Standards and Guidance, OSHA, U.S. Department of Labor, Room N-3609, 200 Constitution Avenue, NW., Washington, DC 20210; telephone (202) 693-2222.End Further Info End Preamble Start Supplemental Information
The Department of Labor, as part of its continuing effort to reduce paperwork and respondent (i.e., employer) burden, conducts a preclearance consultation program to provide the public with an opportunity to comment on proposed and continuing information collection requirements in accordance with the Paperwork Reduction Act of 1995 (44 U.S.C. 3506(c)(2)(A)). This program ensures that information is in the desired format, reporting burden (time and costs) is minimal, collection instruments are clearly understood, and Start Printed Page 52038OSHA's estimate of the information collection burden is accurate. The Occupational Safety and Health Act of 1970 (the OSH Act) (29 U.S.C. 651 et seq.) authorizes information collection by employers as necessary or appropriate for enforcement of the OSH Act or for developing information regarding the causes and prevention of occupational injuries, illnesses, and accidents (29 U.S.C. 657). The OSH Act also requires that OSHA obtain such information with minimum burden upon employers, especially those operating small businesses, and to reduce to the maximum extent feasible unnecessary duplication of efforts in obtaining information (29 U.S.C. 657).
Section 1910.255(e) requires that a periodic inspection of resistance welding equipment be made by qualified maintenance personnel, and that a certification record be generated and maintained. The certification shall include the date of the inspection, the signature of the person who performed the inspection and the serial number, or other identifier, for the equipment inspected. The record shall be made available to an OSHA inspector upon request. The maintenance inspection ensures that welding equipment is in safe operating condition while the maintenance record provides evidence to workers and Agency compliance officers that employers performed the required inspections.
II. Special Issues for Comment
OSHA has a particular interest in comments on the following issues:
- Whether the proposed information collection requirements are necessary for the proper performance of the Agency's functions, including whether the information is useful;
- The accuracy of OSHA's estimate of the burden (time and costs) of the information collection requirements, including the validity of the methodology and assumptions used;
- The quality, utility, and clarity of the information collected; and
- Ways to minimize the burden on employers who must comply; for example, by using automated or other technological information collection and transmission techniques.
III. Proposed Actions
OSHA is requesting that OMB extend its approval of the information collection requirements contained in the Standard on Welding, Cutting and Brazing (29 CFR part 1910, subpart Q). The Agency is requesting to reduce its current burden hour estimate associated with this Standard from 5,994 hours to 5,935 hours for a total reduction of 59 hours. The reduction is a result of a decrease in the estimated number of resistance welders. The Agency will summarize any comments submitted in response to this notice and will include this summary in the request to OMB.
Type of Review: Extension of a currently approved collection.
Title: Welding, Cutting and Brazing (29 CFR part 1910, subpart Q).
OMB Number: 1218-0207.
Affected Public: Business or other for-profits.
Number of Respondents: 42,328.
Frequency: On occasion; Semiannually.
Average Time per Response: Varies from 1 minute (.02 hour) to maintain the inspection certification record to 7 minutes (.12 hour) to perform the inspection and to generate and maintain the inspection certification record.
Estimated Total Burden Hours: 5,935.
Estimated Cost (Operation and Maintenance): $0.
IV. Public Participation—Submission of Comments on This Notice and Internet Access to Comments and Submissions
You may submit comments in response to this document as follows: (1) Electronically at http://www.regulations.gov, which is the Federal eRulemaking Portal; (2) by facsimile (fax); or (3) by hard copy. All comments, attachments, and other material must identify the Agency name and the OSHA docket number for the ICR (Docket No. OSHA-2010-0037). You may supplement electronic submissions by uploading document files electronically. If you wish to mail additional materials in reference to an electronic or facsimile submission, you must submit them to the OSHA Docket Office (see the section of this notice titled ADDRESSES). The additional materials must clearly identify your electronic comments by your name, date, and the docket number so the Agency can attach them to your comments.
Because of security procedures, the use of regular mail may cause a significant delay in the receipt of comments. For information about security procedures concerning the delivery of materials by hand, express delivery, messenger, or courier service, please contact the OSHA Docket Office at (202) 693-2350, (TTY (877) 889-5627).
Comments and submissions are posted without change at http://www.regulations.gov. Therefore, OSHA cautions commenters about submitting personal information such as social security numbers and date of birth. Although all submissions are listed in the http://www.regulations.gov index, some information (e.g., copyrighted material) is not publicly available to read or download through this website. All submissions, including copyrighted material, are available for inspection and copying at the OSHA Docket Office. Information on using the http://www.regulations.gov website to submit comments and access the docket is available at the Web site's “User Tips” link. Contact the OSHA Docket Office for information about materials not available through the Web site, and for assistance in using the Internet to locate docket submissions.
V. Authority and Signature
David Michaels, PhD, MPH, Assistant Secretary of Labor for Occupational Safety and Health, directed the preparation of this notice. The authority for this notice is the Paperwork Reduction Act of 1995 (44 U.S.C. 3506 et seq.) and Secretary of Labor's Order No. 5-2007 (67 FR 31160).Start Signature
Signed at Washington, DC, on August 16, 2010.
Assistant Secretary of Labor for Occupational Safety and Health.
[FR Doc. 2010-21055 Filed 8-23-10; 8:45 am]
BILLING CODE 4510-26-P