Environmental Protection Agency (EPA).
EPA is proposing to approve a draft revision to the State Implementation Plan (SIP), submitted by Tennessee, through the Tennessee Department of Environment and Conservation (TDEC), Air Pollution Control Division, to EPA on August 30, 2010, for parallel processing. The proposed SIP revision modifies Tennessee's New Source Review (NSR) Prevention of Significant Deterioration (PSD) program. Specifically, the Start Printed Page 68266proposed SIP revision establishes appropriate emission thresholds for determining which new stationary sources and modification projects become subject to Tennessee's PSD permitting requirements for their greenhouse gas (GHG) emissions. Tennessee's August 30, 2010, SIP revision is necessary because without it, on January 2, 2011, PSD requirements would apply at the 100 or 250 tons per year (tpy) levels provided under the Clean Air Act (CAA or Act), which would overwhelm Tennessee's permitting resources. EPA is proposing approval of Tennessee's August 30, 2010, SIP revision relating to PSD requirements for GHG-emitting sources because the Agency has made the preliminary determination that this SIP revision is in accordance with the CAA and EPA regulations regarding PSD permitting for GHGs.
Comments must be received on or before December 6, 2010.
Submit your comments, identified by Docket ID No. EPA-R04-OAR-2010-0697 , by one of the following methods:
1. http://www.regulations.gov: Follow the on-line instructions for submitting comments.
2. E-mail: firstname.lastname@example.org.
3. Fax: (404) 562-9019.
4. Mail: EPA-R04-OAR-2010-0697, Regulatory Development Section, Air Planning Branch, Air, Pesticides and Toxics Management Division, U.S. Environmental Protection Agency, Region 4, 61 Forsyth Street, SW., Atlanta, Georgia 30303-8960.
5. Hand Delivery or Courier: Ms. Lynorae Benjamin, Chief, Regulatory Development Section, Air Planning Branch, Air, Pesticides and Toxics Management Division, U.S. Environmental Protection Agency, Region 4, 61 Forsyth Street, SW., Atlanta, Georgia 30303-8960. Such deliveries are only accepted during the Regional Office's normal hours of operation. The Regional Office's official hours of business are Monday through Friday, 8:30 to 4:30, excluding Federal holidays.
Instructions: Direct your comments to Docket ID No. “EPA-R04-OAR-2010-0697.” EPA's policy is that all comments received will be included in the public docket without change and may be made available online at http://www.regulations.gov, including any personal information provided, unless the comment includes information claimed to be Confidential Business Information (CBI) or other information whose disclosure is restricted by statute. Do not submit through http://www.regulations.gov or e-mail, information that you consider to be CBI or otherwise protected. The http://www.regulations.gov Web site is an “anonymous access” system, which means EPA will not know your identity or contact information unless you provide it in the body of your comment. If you send an e-mail comment directly to EPA without going through http://www.regulations.gov, your e-mail address will be automatically captured and included as part of the comment that is placed in the public docket and made available on the Internet. If you submit an electronic comment, EPA recommends that you include your name and other contact information in the body of your comment and with any disk or CD-ROM you submit. If EPA cannot read your comment due to technical difficulties and cannot contact you for clarification, EPA may not be able to consider your comment. Electronic files should avoid the use of special characters, any form of encryption, and be free of any defects or viruses. For additional information about EPA's public docket visit the EPA Docket Center homepage at http://www.epa.gov/epahome/dockets.htm.
Docket: All documents in the electronic docket are listed in the http://www.regulations.gov index. Although listed in the index, some information is not publicly available, i.e., CBI or other information whose disclosure is restricted by statute. Certain other material, such as copyrighted material, is not placed on the Internet and will be publicly available only in hard copy form. Publicly available docket materials are available either electronically in http://www.regulations.gov or in hard copy at the Regulatory Development Section, Air Planning Branch, Air, Pesticides and Toxics Management Division, U.S. Environmental Protection Agency, Region 4, 61 Forsyth Street, SW., Atlanta, Georgia 30303-8960. EPA requests that if at all possible, you contact the person listed in the FOR FURTHER INFORMATION CONTACT section to schedule your inspection. The Regional Office's official hours of business are Monday through Friday, 8:30 to 4:30, excluding Federal holidays.Start Further Info
FOR FURTHER INFORMATION CONTACT:
For information regarding the Tennessee SIP, contact Ms. Twunjala Bradley, Regulatory Development Section, Air Planning Branch, Air, Pesticides and Toxics Management Division, U.S. Environmental Protection Agency, Region 4, 61 Forsyth Street, SW., Atlanta, Georgia 30303-8960. Ms. Bradley's telephone number is (404) 562-9352; e-mail address: email@example.com. For information regarding the Tailoring Rule, contact Ms. Heather Abrams, Air Permits Section, at the same address above. Ms. Abrams' telephone number is (404) 562-9185; e-mail address: firstname.lastname@example.org.End Further Info End Preamble Start Supplemental Information
Table of Contents
I. What action is EPA proposing in today's notice?
II. What is the background for the action proposed by EPA in today's notice?
III. What is the relationship between today's proposed action and EPA's proposed GHG SIP Call and GHG FIP?
IV. What is EPA's analysis of Tennessee's proposed SIP revision?
V. Proposed Action
VI. Statutory and Executive Order Reviews
I. What action is EPA proposing in today's notice?
On August 30, 2010, TDEC submitted a draft revision to EPA for approval into the Tennessee SIP to establish appropriate emission thresholds for determining which new or modified stationary sources become subject to Tennessee's PSD permitting requirements for GHG emissions. Final approval of Tennessee's August 30, 2010, SIP revision will put in place the GHG emission thresholds for PSD applicability set forth in EPA's Tailoring Rule (75 FR 31514, June 3, 2010), ensuring that smaller GHG sources emitting less than these thresholds will not be subject to permitting requirements when these requirements begin applying to GHGs on January 2, 2011. Pursuant to section 110 of the CAA, EPA is proposing to approve this revision into the Tennessee SIP.
Because this draft SIP revision is not yet state-effective, Tennessee requested that EPA “parallel process” the SIP revision. Under this procedure, the EPA Regional Office works closely with the state while developing new or revised regulations. Generally, the state submits a copy of the proposed regulation or other revisions to EPA before conducting its public hearing. EPA reviews this proposed state action and prepares a notice of proposed rulemaking. EPA publishes this notice of proposed rulemaking in the Federal Register and solicits public comment in approximately the same time frame during which the state is holding its public hearing. The state and EPA thus provide for public comment periods on both the state and the federal actions in parallel.
After Tennessee submits the formal state-effective SIP revision request (including a response to all public comments raised during the state's Start Printed Page 68267public participation process), EPA will prepare a final rulemaking notice for the SIP revision. If changes are made to the SIP revision after EPA's notice of proposed rulemaking, such changes must be acknowledged in EPA's final rulemaking action. If the changes are significant, then EPA may be obliged to re-propose the action. In addition, if the changes render the SIP revision not approvable, EPA's re-proposal of the action would be a disapproval of the revision.
II. What is the background for the action proposed by EPA in today's notice?
Today's proposed action on the Tennessee SIP relates to EPA's “Prevention of Significant Deterioration and Title V Greenhouse Gas Tailoring Rule,” Final Rule (the Tailoring Rule). 75 FR 31514. In the Tailoring Rule, EPA established appropriate GHG emission thresholds for determining the applicability of PSD requirements to GHG-emitting sources. These applicability thresholds were designed to ensure that smaller GHG sources will not be subject to GHG permitting requirements. While Tennessee already has authority to issue PSD permits governing GHGs when PSD requirements begin applying to GHGs on January 2, 2011, Tennessee needs to amend its SIP to incorporate the Tailoring Rule's applicability thresholds. Today's notice announces EPA's proposed approval of a revision to Tennessee's SIP that would put these applicability thresholds in place.
Below is a brief overview of GHGs and GHG-emitting sources, the CAA PSD program, minimum SIP elements for a PSD program, and EPA's recent actions regarding GHG permitting. Following this section, EPA discusses, in sections III and IV, the relationship between the proposed Tennessee SIP revision and EPA's other national rulemakings as well as EPA's analysis of Tennessee's SIP revision.
A. What are GHGs and their sources?
A detailed explanation of GHGs, climate change and the impact on health, society, and the environment is included in EPA's technical support document for EPA's GHG endangerment finding final rule (Document ID No. EPA-HQ-OAR-2009-0472-11292 at http://www.regulations.gov). The endangerment finding rulemaking is discussed later in this rulemaking. A summary of the nature and sources of GHGs is provided below.
GHGs trap the Earth's heat that would otherwise escape from the atmosphere into space and form the greenhouse effect that helps keep the Earth warm enough for life. GHGs are naturally present in the atmosphere and are also emitted by human activities. Human activities are intensifying the naturally occurring greenhouse effect by increasing the amount of GHGs in the atmosphere, which is changing the climate in a way that endangers human health, society, and the natural environment.
Some GHGs, such as carbon dioxide (CO2), are emitted to the atmosphere through natural processes as well as human activities. Other gases, such as fluorinated gases, are created and emitted solely through human activities. The well-mixed GHGs of concern directly emitted by human activities include CO2, methane (CH4), nitrous oxide (N2 O), hydrofluorocarbons (HFCs), perfluorocarbons (PFCs), and sulfur hexafluoride (SF6), hereafter referred to collectively as “the six well-mixed GHG,” or, simply, GHGs. Together these six well-mixed GHGs constitute the “air pollutant” upon which the GHG thresholds in EPA's Tailoring Rule are based. These six gases remain in the atmosphere for decades to centuries where they become well-mixed globally in the atmosphere. When they are emitted more quickly than natural processes can remove them from the atmosphere, their concentrations increase, thus increasing the greenhouse effect.
In the U.S., the combustion of fossil fuels (e.g., coal, oil, gas) is the largest source of CO2 emissions and accounts for 80 percent of the total GHG emissions by mass. Anthropogenic CO2 emissions released from a variety of sources, including through the use of fossil fuel combustion and cement production from geologically stored carbon (e.g., coal, oil, and natural gas) that is hundreds of millions of years old, as well as anthropogenic CO2 emissions from land-use changes such as deforestation, perturb the atmospheric concentration of CO2, and the distribution of carbon within different reservoirs readjusts. More than half of the energy-related emissions come from large stationary sources such as power plants, while about a third come from transportation. Of the six well-mixed GHGs, four (CO2, CH4, N2 O, and HFCs) are emitted by motor vehicles. In the U.S., industrial processes (such as the production of cement, steel, and aluminum), agriculture, forestry, other land use, and waste management are also important sources of GHGs.
Different GHGs have different heat-trapping capacities. The concept of Global Warming Potential (GWP) was developed to compare the heat-trapping capacity and atmospheric lifetime of one GHG to another. The definition of a GWP for a particular GHG is the ratio of heat trapped by one unit mass of the GHG to that of one unit mass of CO2 over a specified time period. When quantities of the different GHGs are multiplied by their GWPs, the different GHGs can be summed and compared on a carbon dioxide equivalent (CO2 e) basis. For example, CH4 has a GWP of 21, meaning each ton of CH4 emissions would have 21 times as much impact on global warming over a 100-year time horizon as 1 ton of CO2 emissions. Thus, on the basis of heat-trapping capability, 1 ton of CH4 would equal 21 tons of CO2 e. The GWPs of the non-CO2 GHG range from 21 (for CH4) up to 23,900 (for SF6). Aggregating all GHG on a CO2 e basis at the source level allows a facility to evaluate its total GHG emissions contribution based on a single metric.
B. What are the general requirements of the PSD program?
1. Overview of the PSD Program
The PSD program is a preconstruction review and permitting program applicable to new major stationary sources and major modifications at existing stationary sources. The PSD program applies in areas that are designated “attainment” or “unclassifiable” for a national ambient air quality standard (NAAQS). The PSD program is contained in part C of title I of the CAA. The “nonattainment NSR” program applies in areas not in attainment of a NAAQS or in the Ozone Transport Region, and it is implemented under the requirements of part D of title I of the CAA. Collectively, EPA commonly refers to these two programs as the major NSR program. The governing EPA rules are contained in 40 CFR 51.165, 51.166, 52.21, 52.24, and part 51, Appendices S and W. There is no NAAQS for CO2 or any of the other well-mixed GHGs, nor has EPA proposed any such NAAQS; Therefore, unless and until EPA takes further such action, the nonattainment NSR program does not apply to GHGs.
The applicability of PSD to a particular source must be determined in Start Printed Page 68268advance of construction or modification and is pollutant-specific. The primary criterion in determining PSD applicability is whether the proposed project is sufficiently large (in terms of its emissions) to be a major stationary source or modification, both of which are described below. EPA has implemented these requirements in its regulations, which use somewhat different terminology than the CAA does, for determining PSD applicability.
a. Major Stationary Sources
Under PSD, a “major stationary source” is any source belonging to a specified list of 28 source categories that emits or has the potential to emit 100 tpy or more of any air pollutant subject to regulation under the CAA, or any other source type that emits or has the potential to emit such pollutants in amounts equal to or greater than 250 tpy. See, e.g., 40 CFR 52.21(b)(1). We refer to these levels as the 100/250-tpy thresholds. A new source with a potential to emit (PTE) at or above the applicable “major stationary source threshold” is subject to major NSR. These limits originate from section 169 of the CAA, which applies PSD to any “major emitting facility” and defines the term to include any source that emits or has a PTE of 100 or 250 tpy, depending on the source category. Note that the major source definition incorporates the phrase “subject to regulation,” which, as described later, will begin to include GHGs on January 2, 2011, under our interpretation of that phrase as discussed in the recent memorandum entitled, “EPA's Interpretation of Regulations that Determine Pollutants Covered by Federal Prevention of Significant Deterioration (PSD) Permit Program.” 75 FR 17004 (April 2, 2010).
b. Major Modifications
PSD also applies to existing sources that undertake a “major modification,” which occurs when: (1) There is a physical change in, or change in the method of operation of, a “major stationary source;” (2) the change results in a “significant” emissions increase of a pollutant subject to regulation (equal to or above the significance level that EPA has set for the pollutant in 40 CFR 52.21(b)(23)); and (3) there is a “significant net emissions increase” of a pollutant subject to regulation that is equal to or above the significance level (defined in 40 CFR 52.21(b)(23)). Significance levels, which EPA has promulgated for criteria pollutants and certain other pollutants, represent a de minimis contribution to air quality problems. When EPA has not set a significance level for a regulated NSR pollutant, PSD applies to an increase of the pollutant in any amount (that is, in effect, the significance level is treated as zero).
2. General Requirements for PSD
This section provides a very brief summary of the main requirements of the PSD program. One principal requirement is that a new major source or major modification must apply best available control technology (BACT), which is determined on a case-by-case basis taking into account, among other factors, the cost effectiveness of the control and energy and environmental impacts. EPA has developed a “top-down” approach for BACT review, which involves a decision process that includes identification of all available control technologies, elimination of technically infeasible options, ranking of remaining options by control and cost effectiveness, and then selection of BACT. Under PSD, once a source is determined to be major for any regulated NSR pollutant, a BACT review is performed for each attainment pollutant that exceeds its PSD significance level as part of new construction or for modification projects at the source, where there is a significant increase and a significant net emissions increase of such pollutant.
In addition to performing BACT, the source must analyze impacts on ambient air quality to assure that sources do not cause or contribute to violation of any NAAQS or PSD increments and must analyze impacts on soil, vegetation, and visibility. In addition, sources or modifications that would impact Class I areas (e.g., national parks) may be subject to additional requirements to protect air quality related values (AQRVs) that have been identified for such areas. Under PSD, if a source's proposed project impacts a Class I area, the Federal Land Manager is notified and is responsible for evaluating a source's projected impact on the AQRVs and recommending either approval or disapproval of the source's permit application based on anticipated impacts. There are currently no NAAQS or PSD increments established for GHGs, and therefore these PSD requirements would not apply for GHGs, even when PSD is triggered for GHGs. However, if PSD is triggered for a GHG-emitting source, all regulated NSR pollutants that the new source emits in significant amounts would be subject to PSD requirements. Therefore, if a facility triggers NSR for non-GHG pollutants for which there are established NAAQS or increments, the air quality, additional impacts, and Class I requirements would apply to those pollutants.
Pursuant to existing PSD requirements, the permitting authority must provide notice of its preliminary decision on a source's application for a PSD permit and must provide an opportunity for comment by the public, industry, and other interested persons. After considering and responding to comments, the permitting authority must issue a final determination on the construction permit. Usually NSR permits are issued by a state or local air pollution control agency that has its own authority to issue PSD permits under a permit program that has been approved by EPA for inclusion in its SIP. In some areas, EPA has delegated its authority to issue PSD permits under federal regulations to the state or local agency. In other areas, EPA issues the permits under its own authority.
C. What are the CAA requirements to include the PSD program in the SIP?
The CAA contemplates that the PSD program be implemented in the first instance by the states and requires that states include PSD requirements in their SIPs. CAA section 110(a)(2)(C) requires that—
Each implementation plan * * * shall * * * include a program to provide for * * * regulation of the modification and construction of any stationary source within the areas covered by the plan as necessary to assure that national ambient air quality standards are achieved, including a permit program as required in part C * * * of this subchapter.
CAA section 110(a)(2)(J) requires that—
Each implementation plan * * * shall * * * meet the applicable requirements of * * * part C of this subchapter (relating to significant deterioration of air quality and visibility protection).
CAA section 161 provides that—
[E]ach applicable implementation plan shall contain emission limitations and such other measures as may be necessary, as determined under regulations promulgated under this part [C], to prevent significant deterioration of air quality in each region * * * designated * * * as attainment or unclassifiable.
These provisions, read in conjunction with the PSD applicability provisions as well as other provisions such as the BACT provision under CAA Section 165(a)(4), mandate that SIPs include Start Printed Page 68269PSD programs that are applicable to, among other things, any air pollutant that is subject to regulation. As discussed below, this includes GHGs on and after January 2, 2011.
A number of states do not have PSD programs approved into their SIPs. In those states, EPA's regulations at 40 CFR 52.21 govern, and either EPA or the state as EPA's delegatee acts as the permitting authority. However, most states have PSD programs that have been approved into their SIPs, and these states implement their PSD programs and act as the permitting authority. Tennessee has a SIP-approved PSD program.
D. What actions has EPA taken concerning PSD requirements for GHG-emitting sources?
1. What are the endangerment finding, the Light Duty Vehicle Rule, and the Johnson Memo reconsideration?
By notice dated December 15, 2009, and pursuant to CAA section 202(a), EPA issued two findings regarding GHGs that are commonly referred to as the “Endangerment Finding” and the “Cause or Contribute Finding.” “Endangerment and Cause or Contribute Findings for Greenhouse Gases Under Section 202(a) of the Clean Air Act,” 74 FR 66496. In the Endangerment Finding, the Administrator found that six long-lived and directly emitted GHGs—CO2, CH4, N2 O, HFCs, PFCs, and SF6—may reasonably be anticipated to endanger public health and welfare In the Cause or Contribute Finding, the Administrator “defin[ed] the air pollutant as the aggregate group of the same six * * * greenhouse gases,” 74 FR at 66536, and found that the combined emissions of this air pollutant from new motor vehicles and new motor vehicle engines contribute to the GHG air pollution that endangers public health and welfare.
By notice dated May 7, 2010, EPA published what is commonly referred to as the “Light-Duty Vehicle Rule” (LDVR), which for the first time established federal controls on GHGs emitted from light-duty vehicles. “Light-Duty Vehicle Greenhouse Gas Emission Standards and Corporate Average Fuel Economy Standards; Final Rule.” 75 FR 25324. In its applicability provisions, the LDVR specifies that it “contains standards and other regulations applicable to the emissions of six greenhouse gases,” including CO2, CH4, N2 O, HFCs, PFCs, and SF6. 75 FR at 25686 (40 CFR 86.1818-12(a)).
On December 18, 2008, EPA issued a memorandum, “EPA's Interpretation of Regulations that Determine Pollutants Covered by Federal Prevention of Significant Deterioration (PSD) Permit Program” (known as the “Johnson Memo” or the “PSD Interpretive Memo,” and referred to in this preamble as the “Interpretive Memo”), that set forth EPA's interpretation regarding which EPA and state actions, with respect to a previously unregulated pollutant, cause that pollutant to become “subject to regulation” under the Act. Whether a pollutant is “subject to regulation” is important for the purposes of determining whether it is covered under the federal PSD permitting program. The Interpretive Memo established that a pollutant is “subject to regulation” only if it is subject to either a provision in the CAA or regulation adopted by EPA under the CAA that requires actual control of emissions of that pollutant (referred to as the “actual control interpretation”). On February 17, 2009, EPA granted a petition for reconsideration on the Interpretive Memo and announced its intent to conduct a rulemaking to allow for public comment on the issues raised in the memorandum and on related issues. EPA also clarified that the Interpretive Memo would remain in effect pending reconsideration.
On March 29, 2010, EPA signed a notice conveying its decision to continue applying (with one limited refinement) the Interpretive Memo's interpretation of “subject to regulation,” “Interpretation of Regulations that Determine Pollutants Covered by Clean Air Act Permitting Programs.” 75 FR 17004. EPA concluded that the “actual control interpretation” is the most appropriate interpretation to apply given the policy implications. However, EPA refined the Agency's interpretation in one respect: EPA established that PSD permitting requirements apply to a newly regulated pollutant at the time a regulatory requirement to control emissions of that pollutant “takes effect” (rather than upon promulgation or the legal effective date of the regulation containing such a requirement). In addition, based on the anticipated promulgation of the LDVR, EPA stated that the GHG requirements of the vehicle rule would take effect on January 2, 2011, because that is the earliest date that a 2012 model year vehicle may be introduced into commerce. In other words, the compliance obligation under the LDVR does not occur until a manufacturer may introduce into commerce vehicles that are required to comply with GHG standards, which will begin with model year 2012 and will not occur before January 2, 2011.
2. What is EPA's Tailoring Rule?
On June 3, 2010 (effective August 2, 2010), EPA promulgated a final rulemaking, the Tailoring Rule, for the purpose of relieving overwhelming permitting burdens that would, in the absence of the rule, fall on permitting authorities and sources. 75 FR 31514. EPA accomplished this by tailoring the applicability criteria that determine which GHG emission sources become subject to the PSD program  of the CAA. In particular, EPA established in the Tailoring Rule a phase-in approach for PSD applicability and established the first two steps of the phase-in for the largest GHG-emitters. Additionally, EPA committed to certain follow-up actions regarding future steps beyond the first two, discussed in more detail later in this notice.
For the first step of the Tailoring Rule, which will begin on January 2, 2011, PSD requirements will apply to major stationary source GHG emissions only if the sources are subject to PSD anyway due to their emissions of non-GHG pollutants. Therefore, in the first step, EPA will not require sources or modifications to evaluate whether they are subject to PSD requirements solely on account of their GHG emissions. Specifically, for PSD, Step 1 requires that as of January 2, 2011, the applicable requirements of PSD, most notably, the BACT requirement, will apply to projects that increase net GHG emissions by at least 75,000 tpy CO2 e, but only if the project also significantly increases emissions of at least one non-GHG pollutant.
The second step of the Tailoring Rule, beginning on July 1, 2011, will phase in additional large sources of GHG emissions. New sources that emit, or have the potential to emit, at least 100,000 tpy CO2 e will become subject to the PSD requirements. In addition, sources that emit or have the potential to emit at least 100,000 tpy CO2 e and that undertake a modification that increases net GHG emissions by at least 75,000 tpy CO2 e will also be subject to PSD requirements. For both steps, EPA notes that if sources or modifications Start Printed Page 68270exceed these CO2 e-adjusted GHG triggers, they are not covered by permitting requirements unless their GHG emissions also exceed the corresponding mass-based triggers in tpy.
EPA believes that the costs to the sources and the administrative burdens to the permitting authorities of PSD permitting will be manageable at the levels in these initial two steps and that it would be administratively infeasible to subject additional sources to PSD requirements at those times. However, EPA also intends to issue a supplemental notice of proposed rulemaking in 2011, in which the Agency will propose or solicit comment on a third step of the phase-in that would include more sources, beginning on July 1, 2013. In the Tailoring Rule, EPA established an enforceable commitment that the Agency will complete this rulemaking by July 1, 2012, which will allow for 1 year's notice before Step 3 would take effect.
In addition, EPA committed to explore streamlining techniques that may well make the permitting programs much more efficient to administer for GHG, and that therefore may allow their expansion to smaller sources. EPA expects that the initial streamlining techniques will take several years to develop and implement.
In the Tailoring Rule, EPA also included a provision, that no source with emissions below 50,000 tpy CO2 e, and no modification resulting in net GHG increases of less than 50,000 tpy CO2 e, will be subject to PSD permitting before at least 6 years (i.e., April 30, 2016). This is because EPA has concluded that at the present time, the administrative burdens that would accompany permitting sources below this level would be so great that even with the streamlining actions that EPA may be able to develop and implement in the next several years, and even with the increases in permitting resources that EPA can reasonably expect the permitting authorities to acquire, it would be impossible to administer the permit programs for these sources until at least 2016.
As EPA explained in the Tailoring Rule, the threshold limitations are necessary because without them, PSD would apply to all stationary sources that emit or have the potential to emit more than 100 or 250 tons of GHG per year beginning on January 2, 2011. This is the date when EPA's recently promulgated LDVR takes effect, imposing control requirements for the first time on CO2 and other GHGs. If this January 2, 2011, date were to pass without the Tailoring Rule being in effect, PSD requirements would apply to GHG emissions at the 100/250 tpy applicability levels provided under a literal reading of the CAA as of that date. From that point forward, a source owner proposing to construct any new major source that emits at or higher than the applicability levels (and which therefore may be referred to as a “major” source) or modify any existing major source in a way that would increase GHG emissions would need to obtain a permit under the PSD program that addresses these emissions before construction or modification could begin.
Under these circumstances, many small sources would be burdened by the costs of the individualized PSD control technology requirements and permit applications that the PSD provisions, absent streamlining, require. Additionally, state and local permitting authorities would be burdened by the extraordinary number of these permit applications, which are orders of magnitude greater than the current inventory of permits and would vastly exceed the current administrative resources of the permitting authorities. Permit gridlock would result since the permitting authorities would likely be able to issue only a tiny fraction of the permits requested.
The Tailoring Rule's thresholds are based on CO2 e for the aggregate sum of six GHGs that constitute the pollutant that will be subject to regulation, which we refer to as GHG. These gases are: CO2, CH4, N2 O, HFCs, PFCs, and SF6. Thus, in EPA's Tailoring Rule, EPA provided that PSD applicability is based on the quantity that results when the mass emissions of each of these gases is multiplied by the GWP of that gas, and then summed for all six gases. However, EPA further provided that in order for a source's GHG emissions to trigger PSD requirements, the quantity of the GHG emissions must equal or exceed both the applicability thresholds established in the Tailoring Rule on a CO2 e basis and the statutory thresholds of 100 or 250 tpy on a mass basis. Similarly, in order for a source to be subject to the PSD modification requirements, the source's net GHG emissions increase must exceed the applicable significance level on a CO2 e basis and must also result in a net mass increase of the constituent gases combined.
In the Tailoring Rule, EPA adopted regulatory language codifying the phase-in approach. As explained in that rulemaking, many state, local and tribal area programs will likely be able to immediately implement the approach without rule or statutory changes by, for example, interpreting the term “subject to regulation” that is part of the applicability provisions for PSD permitting. EPA has requested permitting authorities to confirm that they will follow this implementation approach for their programs, and if they cannot, then EPA has requested that they notify the Agency so that we can take appropriate follow-up action to narrow federal approval of their programs before GHGs become subject to PSD permitting on January 2, 2011. On July 30, 2010, Tennessee provided a letter to EPA confirming that the State has the authority to issue PSD permits governing GHG emissions as of January 2, 2011, but explaining that Tennessee needs to amend its SIP to enable it to implement the Tailoring Rule thresholds. See the docket for this proposed rulemaking for a copy of Tennessee's letter.
3. What is the GHG SIP call?
By Federal Register notice dated September 2, 2010, EPA proposed the GHG SIP Call. In that action, along with the companion GHG FIP rulemaking published at the same time, EPA took steps to ensure that in the 13 States that do not appear to have authority to issue PSD permits to GHG-emitting sources at present, either the state or EPA will have the authority to issue such permits by January 2, 2011. EPA explained that although for most states, either the State or EPA is already authorized to issue PSD permits for GHG-emitting sources as of that date, our preliminary information shows that these 13 States have EPA-approved PSD programs that do not appear to include GHG-emitting sources and therefore do not appear to authorize these States to issue PSD permits to such sources. Therefore, EPA Start Printed Page 68271proposed to find that these 13 States' SIPs are substantially inadequate to comply with CAA requirements and, accordingly, proposed to issue a SIP Call to require a SIP revision that applies their SIP PSD programs to GHG-emitting sources. In the companion GHG FIP rulemaking, EPA proposed a FIP that would give EPA authority to apply EPA's PSD program to GHG-emitting sources in any State that is unable to submit a corrective SIP revision by its deadline. Tennessee was not one of the States for which EPA proposed a SIP Call.
III. What is the relationship between today's proposed action and EPA's proposed GHG SIP call and GHG FIP?
As noted above, by notice dated September 2, 2010, EPA proposed the GHG SIP Call. At the same time, EPA proposed a FIP to apply in any state that is unable to submit, by its deadline, a SIP revision to ensure that the state has authority to issue PSD permits to GHG-emitting sources. As discussed in Section IV of this rulemaking, Tennessee interprets its current PSD regulations as providing them with the authority to regulate GHGs, and as such, Tennessee is not included on the list of areas for the proposed SIP call. Additionally, Tennessee would not be subject to the FIP to implement GHG for PSD applicability. Tennessee's August 17, 2010, proposed SIP revision (the subject of this rulemaking) merely modifies Tennessee's SIP to establish appropriate thresholds for determining which stationary sources and modification projects become subject to permitting requirements for GHG emissions under the PSD program of the CAA.
IV. What is EPA's analysis of Tennessee's SIP revision?
On August 30, 2010, TDEC provided a revision to Tennessee's SIP to EPA for parallel processing and eventual approval. This revision to Tennessee's SIP is necessary because without it, PSD requirements would apply, as of January 2, 2011, at the 100- or 250-tpy levels provided under the CAA. This would greatly increase the number of required permits, imposing undue costs on small sources; which would overwhelm Tennessee's permitting resources and severely impair the function of the program.
The State of Tennessee's August 30, 2010, proposed SIP revision establishes thresholds for determining which stationary sources and modification projects become subject to permitting requirements for GHG emissions under Tennessee's PSD program. Specifically, Tennessee's August 30, 2010, proposed SIP revision includes changes to Tennessee's Air Quality Regulations, 1200-03-09-.01(4)—Construction and Operating Permits, Prevention of Significant Deterioration  and addresses the thresholds for GHG permitting applicability.
Tennessee is currently a SIP-approved state for the PSD program, and has incorporated EPA's 2002 NSR reform revisions for PSD into its SIP. In a letter provided to EPA on July 30, 2010, Tennessee notified EPA of its interpretation that the State currently has the authority to regulate GHGs under TDEC's SIP-approved Rule 1200-03-09-.01(4)—Construction and Operating Permits, Prevention of Significant Deterioration, which includes the preconstruction review program required by Part C of title I of the CAA. The current Tennessee program (adopted prior to the promulgation of EPA's Tailoring Rule) applies to major stationary sources (having the potential to emit at least 100 tpy or 250 tpy or more of a regulated NSR pollutant, depending on the type of source) or modifications constructing in areas designated attainment or unclassifiable with respect to the NAAQS.
EPA performed a line-by-line review of the proposed change to Tennessee's SIP-approved PSD regulations (1200-03-09-.01(4)—Construction and Operating Permits, Prevention of Significant Deterioration) and preliminarily determined that the proposed change is consistent with (and substantively the same as) the change to the federal provisions made by EPA's Tailoring Rule. Furthermore, EPA preliminarily determined that this revision to Tennessee's SIP is consistent with section 110 of the CAA. See, e.g., Tailoring Rule, 75 FR at 31561.
V. Proposed Action
EPA is proposing to approve Tennessee's August 30, 2010, SIP revision, relating to PSD requirements for GHG-emitting sources. Specifically, Tennessee's August 30, 2010, proposed SIP revision establishes appropriate emissions thresholds for determining PSD applicability with respect to new and modified GHG-emitting sources in accordance with EPA's Tailoring Rule. EPA has made the preliminary determination that this SIP revision is approvable because it is in accordance with the CAA and EPA regulations regarding PSD permitting for GHGs.
VI. Statutory and Executive Order Reviews
Under the CAA, the Administrator is required to approve a SIP submission that complies with the provisions of the Act and applicable federal regulations. 42 U.S.C. 7410(k); 40 CFR 52.02(a). Thus, in reviewing SIP submissions, EPA's role is to approve state choices, provided that they meet the criteria of the CAA. Accordingly, this proposed action merely approves the State's law as meeting federal requirements and does not impose additional requirements beyond those imposed by the State's law. For that reason, this proposed action:
- Is not a “significant regulatory action” subject to review by the Office of Management and Budget under Executive Order 12866 (58 FR 51735, October 4, 1993);
- Does not impose an information collection burden under the provisions of the Paperwork Reduction Act (44 U.S.C. 3501 et seq.);
- Is certified as not having a significant economic impact on a substantial number of small entities under the Regulatory Flexibility Act (5 U.S.C. 601 et seq.);
- Does not contain any unfunded mandate or significantly or uniquely affect small governments, as described in the Unfunded Mandates Reform Act of 1995 (Pub. L. 104-4);
- Does not have Federalism implications as specified in Executive Order 13132 (64 FR 43255, August 10, 1999);
- Is not an economically significant regulatory action based on health or safety risks subject to Executive Order 13045 (62 FR 19885, April 23, 1997);
- Is not a significant regulatory action subject to Executive Order 13211 (66 FR 28355, May 22, 2001);
- Is not subject to requirements of Section 12(d) of the National Technology Transfer and Advancement Act of 1995 (15 U.S.C. 272 note) because application of those requirements would be inconsistent with the CAA; and
- Does not provide EPA with the discretionary authority to address, as appropriate, disproportionate human health or environmental effects, using Start Printed Page 68272practicable and legally permissible methods, under Executive Order 12898 (59 FR 7629, February 16, 1994).
In addition, this proposed rule does not have tribal implications as specified by Executive Order 13175 (65 FR 67249, November 9, 2000), because the SIP is not approved to apply in Indian country located in the State, and EPA notes that it will not impose substantial direct costs on tribal governments or preempt tribal law.Start List of Subjects
List of Subjects in 40 CFR Part 52
- Environmental protection
- Air pollution control
- Intergovernmental relations
- and Reporting and recordkeeping requirements
Dated: October 26, 2010.
A. Stanley Meiburg,
Acting Regional Administrator, Region 4.
1. On September 2, 2010, EPA proposed a “SIP Call” that would require those states with SIPs that do not authorize PSD permitting for GHGs to submit a SIP revision providing such authority. 75 FR 53892. In a companion rulemaking, EPA proposed a federal implementation plan (FIP) that would apply in any state that is unable to submit the required SIP revision by its deadline. 75 FR 53883 (September 2, 2010). Because Tennessee's SIP already authorizes Tennessee to regulate GHGs once GHGs become subject to PSD requirements on January 2, 2011, Tennessee is not subject to the proposed SIP Call or FIP.Back to Citation
2. EPA notes that the PSD program has historically operated in this fashion for all pollutants—when new sources or modifications are “major,” PSD applies to all pollutants that are emitted in significant quantities from the source or project. This rule does not alter that for sources or modifications that are major due to their GHG emissions.Back to Citation
3. In the Tailoring Rule, EPA noted that commenters argued, with some variations, that the PSD provisions applied only to NAAQS pollutants, and not GHG, and EPA responded that the PSD provisions apply to all pollutants subject to regulation, including GHG. See 75 FR at 31560-62. EPA maintains its position that the PSD provisions apply to all pollutants subject to regulation, and the Agency incorporates by reference the discussion of this issue in the Tailoring Rule.Back to Citation
4. The Tailoring Rule also applies to the title V program, which requires operating permits for existing sources. However, today's action does not affect Tennessee's title V program.Back to Citation
5. The term “greenhouse gases” is commonly used to refer generally to gases that have heat-trapping properties. However, in this notice, unless noted otherwise, we use it to refer specifically to the pollutant regulated in the LDVR.Back to Citation
6. The relevant thresholds are 100 tpy for title V, and 250 tpy for PSD, except for 28 categories listed in EPA regulations for which the PSD threshold is 100 tpy.Back to Citation
7. Narrowing EPA's approval will ensure that for Federal purposes, sources with GHG emissions that are less than the Tailoring Rule's emission thresholds will not be obligated under Federal law to obtain PSD permits during the gap between when GHG PSD requirements go into effect on January 2, 2011 and when either (1) EPA approves a SIP revision adopting EPA's tailoring approach, or (2) if a state opts to regulate smaller GHG-emitting sources, the state demonstrates to EPA that it has adequate resources to handle permitting for such sources. EPA expects to finalize the narrowing action prior to the January 2, 2011 deadline with respect to those States for which EPA will not have approved the Tailoring Rule thresholds in their SIPs by that time.Back to Citation
8. As explained in the proposed GHG SIP Call (75 FR 53892, 53896), EPA intends to finalize its finding of substantial inadequacy and the SIP call for the 13 listed states by December 1, 2010. EPA requested that the states for which EPA is proposing a SIP call identify the deadline—between 3 weeks and 12 months from the date of signature of the final SIP Call—that they would accept for submitting their corrective SIP revision.Back to Citation
9. Tennessee's submittal also revises regulation 1200-03-09-.02(11)—Operating Permits, however, these definitions relate to Title V and are not included in the SIP. As such, EPA is not proposing to take action to approve Tennessee's update to this regulation in this rulemaking.Back to Citation
[FR Doc. 2010-28009 Filed 11-4-10; 8:45 am]
BILLING CODE 6560-50-P