The Department of Labor (DOL) is submitting the Occupational Safety and Health Administration (OSHA) sponsored information collection request (ICR) titled, “Welding, Cutting, and Brazing Standard,” to the Office of Management and Budget (OMB) for review and approval for continued use, without change, in accordance with the Paperwork Reduction Act of 1995 (PRA), 44 U.S.C. 3501 et seq.
Submit comments on or before January 13, 2014.
A copy of this ICR with applicable supporting documentation; including a description of the likely respondents, proposed frequency of response, and estimated total burden may be obtained free of charge from the RegInfo.gov Web site at http://www.reginfo.gov/public/do/PRAViewICR?ref_nbr=201310-1218-002 (this link will only become active on the day following publication of this notice) or by contacting Michel Smyth by telephone at 202-693-4129 (this is not a toll-free number) or sending an email to DOL_PRA_PUBLIC@dol.gov.
Submit comments about this request by mail or courier to the Office of Information and Regulatory Affairs, Attn: OMB Desk Officer for DOL-OSHA, Office of Management and Budget, Room 10235, 725 17th Street NW., Washington, DC 20503; by Fax: 202-395-6881 (this is not a toll-free number); or by email: OIRA_submission@omb.eop.gov. Commenters are encouraged, but not required, to send a courtesy copy of any comments by mail or courier to the U.S. Department of Labor-OASAM, Office of the Chief Information Officer, Attn: Departmental Information Compliance Management Program, Room N1301, 200 Constitution Avenue NW., Washington, DC 20210; or by email: DOL_PRA_PUBLIC@dol.gov.
Start Further Info
FOR FURTHER INFORMATION CONTACT:
Michel Smyth by telephone at 202-693-4129 (this is not a toll-free number) or by email at DOL_PRA_PUBLIC@dol.gov.
End Further Info
Start Supplemental Information
This ICR seeks to maintain PRA authorization for the information collection requirements contained in the Welding, Cutting, and Brazing Standard, regulations 29 CFR part 1910, subpart Q. More specifically, regulations 29 CFR 1910.255(e) requires that a periodic inspection of resistance welding equipment be made by qualified maintenance personnel and a certification record generated and maintained. The certification shall include the date of the inspection, the signature of the person who performed the inspection and the serial number, or other identifier, for the equipment inspected. The maintenance inspection ensures that welding equipment is in safe operating condition, while the maintenance record provides evidence that employers performed the required inspections. The Occupational Safety and Health Act authorizes this information collection. See 29 U.S.C. 657.
This information collection is subject to the PRA. A Federal agency generally cannot conduct or sponsor a collection of information, and the public is generally not required to respond to an information collection, unless it is approved by the OMB under the PRA and displays a currently valid OMB Control Number. In addition, notwithstanding any other provisions of law, no person shall generally be subject to penalty for failing to comply with a collection of information that does not display a valid Control Number. See 5 CFR 1320.5(a) and 1320.6. The DOL obtains OMB approval for this information collection under Control Number 1218-0207.
OMB authorization for an ICR cannot be for more than three (3) years without renewal, and the current approval for this collection is scheduled to expire on January 31, 2014. The DOL seeks to extend PRA authorization for this information collection for three (3) more years, without any change to existing requirements. The DOL notes that existing information collection requirements submitted to the OMB receive a month-to-month extension while they undergo review. For additional substantive information about this ICR, see the related notice published in the Federal Register on August 28, 2013.
Interested parties are encouraged to send comments to the OMB, Office of Information and Regulatory Affairs at the address shown in the ADDRESSES section within 30 days of publication of this notice in the Federal Register. In order to help ensure appropriate consideration, comments should mention OMB Control Number 1218-0207. The OMB is particularly interested in comments that:Start Printed Page 75948
- Evaluate whether the proposed collection of information is necessary for the proper performance of the functions of the agency, including whether the information will have practical utility;
- Evaluate the accuracy of the agency's estimate of the burden of the proposed collection of information, including the validity of the methodology and assumptions used;
- Enhance the quality, utility, and clarity of the information to be collected; and
- Minimize the burden of the collection of information on those who are to respond, including through the use of appropriate automated, electronic, mechanical, or other technological collection techniques or other forms of information technology, e.g., permitting electronic submission of responses.
Title of Collection: Welding, Cutting, and Brazing Standard.
OMB Control Number: 1218-0207.
Affected Public: Private Sector—businesses or other for-profits.
Total Estimated Number of Respondents: 20,094.
Total Estimated Number of Responses: 80,657.
Total Estimated Annual Burden Hours: 5,635.
Total Estimated Annual Other Costs Burden: $0.
End Supplemental Information
Dated: December 6, 2013.
Departmental Clearance Officer.
[FR Doc. 2013-29727 Filed 12-12-13; 8:45 am]
BILLING CODE 4510-26-P