This PDF is the current document as it appeared on Public Inspection on 12/19/2014 at 08:45 am.
Occupational Safety and Health Administration (OSHA), Labor.
In this notice, OSHA announces its final decision to expand the scope of recognition for Curtis-Straus LLC as a Nationally Recognized Testing Laboratory (NRTL).
The expansion of the scope of recognition becomes effective on December 22, 2014.Start Further Info
FOR FURTHER INFORMATION CONTACT:
Information regarding this notice is available from the following sources:
Press inquiries: Contact Mr. Frank Meilinger, Director, OSHA Office of Communications, U.S. Department of Labor, 200 Constitution Avenue NW., Room N-3647, Washington, DC 20210; telephone: (202) 693-1999; email: firstname.lastname@example.org.
General and technical information: Contact Mr. Kevin Robinson, Acting Director, Office of Technical Programs and Coordination Activities, Directorate of Technical Support and Emergency Management, Occupational Safety and Health Administration, U.S. Department of Labor, 200 Constitution Avenue NW., Room N-3655, Washington, DC 20210; telephone: (202) 693-2110; email: email@example.com. OSHA's Web page includes information about the NRTL Program (see http://www.osha.gov/dts/otpca/nrtl/index.html).End Further Info End Preamble Start Supplemental Information
I. Notice of Final Decision
OSHA hereby gives notice of the expansion of the scope of recognition of Curtis-Straus LLC (CSL) as an NRTL. CSL's expansion covers the addition of one test standard to its scope of recognition.
OSHA recognition of an NRTL signifies that the organization meets the requirements specified by 29 CFR 1910.7. Recognition is an acknowledgment that the organization can perform independent safety testing and certification of the specific products covered within its scope of recognition and is not a delegation or grant of government authority. As a result of recognition, employers may use products properly approved by the NRTL to meet OSHA standards that require testing and certification of the products.
The Agency processes applications by an NRTL for initial recognition, or for expansion or renewal of this recognition, following requirements in Appendix A to 29 CFR 1910.7. This appendix requires that the Agency publish two notices in the Federal Register in processing an application. In the first notice, OSHA announces the application and provides its preliminary finding and, in the second notice, the Agency provides its final decision on the application. These notices set forth the NRTL's scope of recognition or modifications of that scope. OSHA maintains an informational Web page for each NRTL that details its scope of recognition. These pages are available from the Agency's Web site at http://www.osha.gov/dts/otpca/nrtl/index.html.
CSL submitted an application, dated February 12, 2014 (OSHA-2009-0026-0023, Exhibit 14-1—CSL Expansion Application for AAMI ES 60601-1), to expand its recognition to include one additional test standard. OSHA staff performed a comparability analysis and reviewed other pertinent information. OSHA did not perform any on-site reviews in relation to this application.
OSHA published the preliminary notice announcing CSL's expansion application in the Federal Register on August 29, 2014 (79 FR 51616). The Agency requested comments by September 15, 2014, but it received no comments in response to this notice. OSHA now is proceeding with this final notice to grant expansion of CSL's scope of recognition.
To obtain or review copies of all public documents pertaining to CSL's application, go to www.regulations.gov or contact the Docket Office, Occupational Safety and Health Administration, U.S. Department of Labor, 200 Constitution Avenue NW., Room N-2625, Washington, DC 20210. Docket No. OSHA-2009-0026 contains all materials in the record concerning CSL's recognition.
II. Final Decision and Order
OSHA staff examined CSL's expansion application, its capability to meet the requirements of the test standard, and other pertinent information. Based on its review of this evidence, OSHA finds that CSL meets the requirements of 29 CFR 1910.7 for expansion of its recognition, subject to the limitation and conditions listed below. OSHA, therefore, is proceeding with this final notice to grant CSL's scope of recognition. OSHA limits the expansion of CSL's recognition to testing and certification of products for demonstration of conformance to the test standard listed in Table 1 below.
|Test standard||Test standard title|
|AAMI ES60601-1||Medical electrical equipment—Part 1: General requirements for basic safety and essential performance.|
OSHA's recognition of any NRTL for a particular test standard is limited to equipment or materials for which OSHA standards require third-party testing and certification before using them in the workplace. Consequently, if a test standard also covers any products for which OSHA does not require such testing and certification, an NRTL's Start Printed Page 76394scope of recognition does not include these products.
The American National Standards Institute (ANSI) may approve the test standards listed above as American National Standards. However, for convenience, we may use the designation of the standards-developing organization for the standard as opposed to the ANSI designation. Under the NRTL Program's policy (see OSHA Instruction CPL 1-0.3, Appendix C, paragraph XIV), any NRTL recognized for a particular test standard may use either the proprietary version of the test standard or the ANSI version of that standard. Contact ANSI to determine whether a test standard is currently ANSI-approved.
In addition to those conditions already required by 29 CFR 1910.7, CSL must abide by the following conditions of the recognition:
1. CSL must inform OSHA as soon as possible, in writing, of any change of ownership, facilities, or key personnel, and of any major change in its operations as an NRTL, and provide details of the change(s);
2. CSL must meet all the terms of its recognition and comply with all OSHA policies pertaining to this recognition; and
3. CSL must continue to meet the requirements for recognition, including all previously published conditions on CSL's scope of recognition, in all areas for which it has recognition.
Pursuant to the authority in 29 CFR 1910.7, OSHA hereby expands the scope of recognition of CSL, subject to the limitation and conditions specified above.
III. Authority and Signature
David Michaels, Ph.D., MPH, Assistant Secretary of Labor for Occupational Safety and Health, 200 Constitution Avenue NW., Washington, DC 20210, authorized the preparation of this notice. Accordingly, the Agency is issuing this notice pursuant to 29 U.S.C. 657(g)(2), Secretary of Labor's Order No. 1-2012 (77 FR 3912, Jan. 25, 2012), and 29 CFR 1910.7.Start Signature
Signed at Washington, DC, on December 15, 2014.
Assistant Secretary of Labor for Occupational Safety and Health.
[FR Doc. 2014-29825 Filed 12-19-14; 8:45 am]
BILLING CODE 4510-26-P