This PDF is the current document as it appeared on Public Inspection on 02/20/2015 at 08:45 am.
Federal Highway Administration (FHWA), Department of Transportation (DOT).
This notice provides information regarding FHWA's finding that a Buy America waiver is appropriate for the obligation of Federal-aid funds for 75 State projects involving the acquisition of vehicles and equipment on the condition that they be assembled in the U.S.
The effective date of the waiver is February 24, 2015.Start Further Info
FOR FURTHER INFORMATION CONTACT:
For questions about this notice, please contact Mr. Gerald Yakowenko, FHWA Office of Program Administration, 202-366-1562, or via email at email@example.com. For legal questions, please contact Mr. Jomar Maldonado, FHWA Office of the Chief Counsel, 202-366-1373, or via email at firstname.lastname@example.org. Office hours for the FHWA are from 8:00 a.m. to 4:30 p.m., e.t., Monday through Friday, except Federal holidays.End Further Info End Preamble Start Supplemental Information
An electronic copy of this document may be downloaded from the Federal Register's home page at http://www.archives.gov and the Government Start Printed Page 9503Publishing Office's database at http://www.access.gpo.gov/nara.
This notice provides information regarding FHWA's finding that a Buy America waiver is appropriate for the obligation of Federal-aid funds for 75 State projects involving the acquisition of vehicles (including sedans, vans, pickups, trucks, buses, and street sweepers) and equipment (such as electric charging station and trail grooming equipment) on the condition that they be assembled in the U.S. The waiver would apply to approximately 950 vehicles. The requests, available at http://www.fhwa.dot.gov/construction/contracts/cmaq141124.cfm, are incorporated by reference into this notice. These projects are being undertaken to implement air quality improvement, safety, and mobility goals under FHWA's Congestion Mitigation and Air Quality Improvement Program; National Bridge and Tunnel Inventory and Inspection Program; and the Recreational Trails Program.
Title 23, Code of Federal Regulations, section 635.410 requires that steel or iron materials (including protective coatings) that will be permanently incorporated in a Federal-aid project must be manufactured in the U.S. For FHWA, this means that all the processes that modified the chemical content, physical shape or size, or final finish of the material (from initial melting and mixing, continuing through the bending and coating) occurred in the U.S. The statute and regulations create a process for granting waivers from the Buy America requirements when its application would be inconsistent with the public interest or when satisfactory quality domestic steel and iron products are not sufficiently available. In 1983, FHWA determined that it was both in the public interest and consistent with the legislative intent to waive Buy America for manufactured products other than steel manufactured products. However, FHWA's national waiver for manufactured products does not apply to the requests in this notice because they involve predominately steel and iron manufactured products. The FHWA's Buy America requirements do not have special provisions for applying Buy America to “rolling stock” such as vehicles or vehicle components (see 49 U.S.C. 5323(j)(2)(C), 49 CFR 661.11, and 49 U.S.C. 24405(a)(2)(C) for examples of Buy America rolling stock provisions for other DOT agencies).
Based on all the information available to the agency, FHWA concludes that there are no domestic manufacturers that produce the vehicles and vehicle components identified in this notice in such a way that their steel and iron elements are manufactured domestically. The FHWA's Buy America requirements were tailored to the types of products that are typically used in highway construction, which generally meet the requirement that steel and iron materials be manufactured domestically. In today's global industry, vehicles are assembled with iron and steel components that are manufactured all over the world. The FHWA is not aware of any domestically produced vehicle on the market that meets FHWA's Buy America requirement to have all its iron and steel be manufactured exclusively in the U.S. For example, the Chevrolet Volt, which was identified by many commenters in a November 21, 2011, Federal Register Notice (76 FR 72027) as a car that is made in the U.S., is comprised of only 45 percent of U.S. and Canadian content according to the National Highway Traffic Safety Administration's Part 583 American Automobile Labeling Act Report Web page (http://www.nhtsa.gov/Laws+&+Regulations/Part+583+American+Automobile+Labeling+Act+(AALA)+Reports). Moreover, there is no indication of how much of this 45 percent content is U.S.-manufactured (from initial melting and mixing) iron and steel content.
In accordance with Division A, section 122 of the Consolidated and Further Continuing Appropriations Act of 2012 (Pub. L. 112-284), FHWA published a notice of intent to issue a waiver on its Web site at http://www.fhwa.dot.gov/construction/contracts/waivers.cfm?id=101 on November 25, 2014. The FHWA received 17 comments in response to the publication. Eight commenters including; Puget Sound Clean Air Agency, Port of Seattle, Chicago Metropolitan Agency for Planning, and Virginia DOT support granting a waiver. Four commenters objected to the waiver, and five others provided general statements regarding domestic manufacturing and the U.S. economy. None of the four commenters objecting to the waiver identified a manufacturer that meets the Buy America requirements for the vehicles and equipment listed in the November 25, 2014 notice.
Based on FHWA's conclusion that there are no domestic manufacturers that can produce the vehicles and equipment identified in this notice in such a way that steel and iron materials are manufactured domestically, and after consideration of the comments received, FHWA finds that application of FHWA's Buy America requirements to these products is inconsistent with the public interest (23 U.S.C. 313(b)(1) and 23 CFR 635.410(c)(2)(i)). However, FHWA believes that it is in the public interest and consistent with the Buy America requirements to impose the condition that the vehicles and the vehicle components be assembled in the U.S. Requiring final assembly to be performed in the U.S. is consistent with past guidance to FHWA Division Offices on manufactured products (see Memorandum on Buy America Policy Response, Dec. 22, 1997, http://www.fhwa.dot.gov/programadmin/contracts/122297.cfm). A waiver of the Buy America requirement without any regard to where the vehicle is assembled would diminish the purpose of the Buy America requirement. Moreover, in today's economic environment, the Buy America requirement is especially significant in that it will ensure that Federal Highway Trust Fund dollars are used to support and create jobs in the U.S. This approach is similar to the conditional waivers previously given for various vehicle projects. Thus, so long as the final assembly of the 75 State projects occurs in the U.S., applicants to this waiver request may proceed to purchase these vehicles and equipment consistent with the Buy America requirement.
In accordance with the provisions of section 117 of the Safe, Accountable, Flexible, Efficient Transportation Equity Act: A Legacy for Users, Technical Corrections Act of 2008 (Pub. L. 110-244), FHWA is providing this notice of its finding that a public interest waiver of Buy America requirements is appropriate on the condition that the vehicles and equipment identified in the notice be assembled in the U.S. The FHWA invites public comment on this finding for an additional 15 days following the effective date of the finding. Comments may be submitted to FHWA's Web site via the link provided to the waiver page noted above.Start Signature
Issued on: February 13, 2015.
Gregory G. Nadeau,
Acting Administrator, Federal Highway Administration.
[FR Doc. 2015-03564 Filed 2-20-15; 8:45 am]
BILLING CODE 4910-22-P