Skip to Content

Notice

Notice of Receipt of Petition for Decision That Nonconforming 2008 Cadillac Escalade Multipurpose Vehicles Are Eligible for Importation

Document Details

Information about this document as published in the Federal Register.

Enhanced Content

Relevant information about this document from Regulations.gov provides additional context. This information is not part of the official Federal Register document.

Published Document

This document has been published in the Federal Register. Use the PDF linked in the document sidebar for the official electronic format.

Start Preamble

AGENCY:

National Highway Traffic Safety Administration, DOT.

ACTION:

Receipt of petition.

SUMMARY:

This document announces receipt by the National Highway Traffic Safety Administration (NHTSA) of a petition for a decision that nonconforming 2008 Cadillac Escalade multipurpose passenger vehicles (MPV) that were not originally manufactured to comply with all applicable Federal motor vehicle safety standards (FMVSS), are eligible for importation into the United States because they are Start Printed Page 36405substantially similar to vehicles that were originally manufactured for sale in the United States and that were certified by their manufacturer as complying with the safety standards (the U.S.-certified version of the 2008 Cadillac Escalade) and they are capable of being readily altered to conform to the standards.

DATES:

The closing date for comments on the petition is July 24, 2015.

ADDRESSES:

Comments should refer to the docket and notice numbers above and be submitted by any of the following methods:

  • Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the online instructions for submitting comments.
  • Mail: Docket Management Facility: U.S. Department of Transportation, 1200 New Jersey Avenue SE., West Building Ground Floor, Room W12-140, Washington, DC 20590-0001.
  • Hand Delivery or Courier: West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE., between 9 a.m. and 5 p.m. ET, Monday through Friday, except Federal holidays.
  • Fax: 202-493-2251.

Instructions: Comments must be written in the English language, and be no greater than 15 pages in length, although there is no limit to the length of necessary attachments to the comments. If comments are submitted in hard copy form, please ensure that two copies are provided. If you wish to receive confirmation that your comments were received, please enclose a stamped, self-addressed postcard with the comments. Note that all comments received will be posted without change to http://www.regulations.gov, including any personal information provided. Please see the Privacy Act heading below.

Privacy Act: Anyone is able to search the electronic form of all comments received into any of our dockets by the name of the individual submitting the comment (or signing the comment, if submitted on behalf of an association, business, labor union, etc.). You may review DOT's complete Privacy Act Statement in the Federal Register published on April 11, 2000 (65 FR 19477-78).

How to Read Comments Submitted to the Docket: You may read the comments received by Docket Management at the address and times given above. You may also view the documents from the Internet at http://www.regulations.gov. Follow the online instructions for accessing the dockets. The docket ID number and title of this notice are shown at the heading of this document notice. Please note that even after the comment closing date, we will continue to file relevant information in the Docket as it becomes available. Further, some people may submit late comments. Accordingly, we recommend that you periodically search the Docket for new material.

Start Further Info

FOR FURTHER INFORMATION CONTACT:

George Stevens, Office of Vehicle Safety Compliance, NHTSA (202-366-5308).

End Further Info End Preamble Start Supplemental Information

SUPPLEMENTARY INFORMATION:

Background

Under 49 U.S.C. 30141(a)(1)(A), a motor vehicle that was not originally manufactured to conform to all applicable FMVSS shall be refused admission into the United States unless NHTSA has decided that the motor vehicle is substantially similar to a motor vehicle originally manufactured for importation into and sale in the United States, certified under 49 U.S.C. 30115, and of the same model year as the model of the motor vehicle to be compared, and is capable of being readily altered to conform to all applicable FMVSS.

Petitions for eligibility decisions may be submitted by either manufacturers or importers who have registered with NHTSA pursuant to 49 CFR part 592. As specified in 49 CFR 593.7, NHTSA publishes notice in the Federal Register of each petition that it receives, and affords interested persons an opportunity to comment on the petition. At the close of the comment period, NHTSA decides, on the basis of the petition and any comments that it has received, whether the vehicle is eligible for importation. The agency then publishes this decision in the Federal Register.

Wallace Environmental Testing Laboratories (“WETL”), Inc. of Houston, Texas (Registered Importer R-90-005) has petitioned NHTSA to decide whether nonconforming 2008 Cadillac Escalade MPV are eligible for importation into the United States. The vehicles which WETL believes are substantially similar are 2008 Cadillac Escalade MPV that were manufactured for sale in the United States and certified by their manufacturer as conforming to all applicable FMVSS.

The petitioner claims that it compared non-U.S. certified 2008 Cadillac Escalade MPV to their U.S.-certified counterparts, and found the vehicles to be substantially similar with respect to compliance with most FMVSS.

WETL submitted information with its petition intended to demonstrate that non-U.S. certified 2008 Cadillac Escalade MPV, as originally manufactured, conform to many FMVSS in the same manner as their U.S.-certified counterparts, or are capable of being readily altered to conform to those standards. Specifically, the petitioner claims that non-U.S. certified 2008 Cadillac Escalade MPV are identical to their U.S.-certified counterparts with respect to compliance with Standard Nos. 102 Transmission Shift Lever Sequence, Starter Interlock, and Transmission Braking Effect, 103 Windshield Defrosting and Defogging Systems, 104 Windshield Wiping and Washing Systems, 106 Brake Hoses, 109 New Pneumatic Tires, 110 Tire Selection and Rims, 113 Hood Latch System, 114 Theft Protection, 116 Motor Vehicle Brake Fluids, 118 Power-Operated Window, Partition, and Roof panel System, 124 Accelerator Control Systems, 135 Light Vehicle Brake Systems, 201 Occupant Protection in Interior Impact, 202 Head Restraints, 204 Steering Control Rearward Displacement, 205 Glazing Materials, 206 Door Locks and Door Retention Components, 207 Seating Systems, 209 Seat Belt Assemblies, 210 Seat Belt Assembly Anchorages, 212 Windshield Mounting, 214 Side Impact Protection, 216 Roof Crush Resistance, 219 Windshield Zone Intrusion, 225 Child Restraint Anchorage Systems, and 302 Flammability of Interior Materials.

The petitioner also contends that the vehicles are capable of being readily altered to meet the following standards, in the manner indicated:

Standard No. 101 Controls and Displays: Modification of the brake warning telltale through replacement of the tachometer with the U.S.-model component, which includes a compliant brake telltale, or by adding a brake telltale which complies with the requirements of the standard.

Standard No. 108 Lamps, Reflective Devices and Associated Equipment: Replacement of the headlamps and tail lamps with U.S.-model components.

Standard No. 111 Rearview Mirrors: Inscription of the required warning statement on the face of the passenger mirror.

Standard No. 138 Tire Pressure Monitoring Systems: Addition of U.S.-model tire pressure monitoring system components including, tire pressure sensors, transmitter, antenna, receiver, and software. In addition, verification that system functionality meets the requirements of the standard will be performed by testing each of the subject vehicles after installation of the U.S.-model components.

Standard No. 208 Occupant Crash Protection: A U.S.-version of the owner's manual must be provided with Start Printed Page 36406the vehicle to meet the information requirements of the standard.

Standard No. 301 Fuel System Integrity: Installation of a rollover valve in the fuel tank vent line between the fuel tank and the evaporative emissions collection canister to comply with the requirements of this standard.

The petitioner additionally states that a vehicle identification plate must be affixed to the vehicle near the left windshield post to meet the requirements of 49 CFR part 565.

All comments received before the close of business on the closing date indicated above will be considered, and will be available for examination in the docket at the above addresses both before and after that date. To the extent possible, comments filed after the closing date will also be considered. Notice of final action on the petition will be published in the Federal Register pursuant to the authority indicated below.

Start Authority

Authority: 49 U.S.C. 30141(a)(1)(A), (a)(1)(B), and (b)(1); 49 CFR 593.7; delegation of authority at 49 CFR 1.95 and 501.8.

End Authority Start Signature

Jeffrey Giuseppe,

Director, Office of Vehicle Safety Compliance.

End Signature End Supplemental Information

[FR Doc. 2015-15426 Filed 6-23-15; 8:45 am]

BILLING CODE 4910-59-P