Skip to Content


Curtis-Straus LLC: Grant of Expansion of Recognition

Document Details

Information about this document as published in the Federal Register.

Document Statistics
Document page views are updated periodically throughout the day and are cumulative counts for this document including its time on Public Inspection. Counts are subject to sampling, reprocessing and revision (up or down) throughout the day.
Published Document

This document has been published in the Federal Register. Use the PDF linked in the document sidebar for the official electronic format.

Start Preamble


Occupational Safety and Health Administration (OSHA), Labor.




In this notice, OSHA announces its final decision to expand the scope of recognition for Curtis-Straus LLC, as a Nationally Recognized Testing Laboratory (NRTL).


The expansion of the scope of recognition becomes effective on August 10, 2015.

Start Further Info


Information regarding this notice is available from the following sources:

Press inquiries: Contact Mr. Frank Meilinger, Director, OSHA Office of Communications, U.S. Department of Labor, 200 Constitution Avenue NW., Room N-3647, Washington, DC 20210; telephone: (202) 693-1999; email:

General and technical information: Contact Mr. Kevin Robinson, Director, Office of Technical Programs and Coordination Activities, Directorate of Technical Support and Emergency Management, Occupational Safety and Health Administration, U.S. Department of Labor, 200 Constitution Avenue NW., Room N-3655, Washington, DC 20210; telephone: (202) 693-2110; email: OSHA's Web page includes information about the NRTL Program (see​dts/​otpca/​nrtl/​index.html).

End Further Info End Preamble Start Supplemental Information


I. Notice of Final Decision

OSHA hereby gives notice of the expansion of the scope of recognition of Curtis-Straus LLC (CSL) as an NRTL. CSL's expansion covers the addition of nine test standards to its scope of recognition.

OSHA recognition of an NRTL signifies that the organization meets the requirements specified by 29 CFR 1910.7. Recognition is an acknowledgment that the organization can perform independent safety testing and certification of the specific products covered within its scope of recognition and is not a delegation or grant of government authority. As a result of recognition, employers may use products properly approved by the NRTL to meet OSHA standards that require testing and certification of the products.

The Agency processes applications by an NRTL for initial recognition, or for expansion or renewal of this recognition, following requirements in Appendix A to 29 CFR 1910.7. This appendix requires that the Agency publish two notices in the Federal Register in processing an application. In the first notice, OSHA announces the application and provides its preliminary finding and, in the second notice, the Agency provides its final decision on the application. These notices set forth the NRTL's scope of recognition or modifications of that scope. OSHA maintains an informational Web page for each NRTL that details its scope of recognition. These pages are available from the Agency's Web site at​dts/​otpca/​nrtl/​index.html.

CSL submitted two applications, one dated August 29, 2014, and one dated February 25, 2015 (OSHA-2009-0026-0057, CSL Exhibit 1—Expansion Application for Nine Standards and OSHA-2009-0026-0058, CSL Exhibit 2—Expansion Application for One Standard). These two applications were combined. OSHA staff performed a comparability analysis and reviewed other pertinent information. OSHA performed an on-site review in relation to these applications on January 27, 2015 to January 28, 2015.

OSHA published the preliminary notice announcing CSL's expansion application in the Federal Register on May 21, 2015 (80 FR 29342). The Agency requested comments by June 5, 2015, but it received no comments in response to this notice. OSHA now is proceeding with this final notice to grant expansion of CSL's scope of recognition.

To obtain or review copies of all public documents pertaining to the CSL's application, go to or contact the Docket Office, Occupational Safety and Health Administration, U.S. Department of Labor, 200 Constitution Avenue NW., Room N-2625, Washington, DC 20210. Docket No. OSHA-2009-0026 contains all materials in the record concerning CSL's recognition.

II. Final Decision and Order

OSHA staff examined CSL's expansion application, its capability to meet the requirements of the test standards, and other pertinent information. Based on its review of this evidence, OSHA finds that CSL meets the requirements of 29 CFR 1910.7 for expansion of its recognition, subject to the specified limitation and conditions listed below. OSHA, therefore, is proceeding with this final notice to grant CSL's scope of recognition. OSHA limits the expansion of CSL's recognition to testing and certification of products for demonstration of conformance to the test standards listed in Table 1 below.Start Printed Page 47956

Table 1—List of Appropriate Test Standards for Inclusion in CSL's NRTL Scope of Recognition

Test standardTest standard title
UL 1012Power Supplies.
UL 1310Direct Plug-In Transformer Units.
UL 60065Audio, Video and Similar Electronic Apparatus.
UL 60950-21Information Technology Equipment—Safety—Part 21: Remote Power Feeding.
UL 60950-22Information Technology Equipment—Safety—Part 22: Equipment to be Installed Outdoors.
UL 60950-23Information Technology Equipment—Safety—Part 23: Large Data Storage Equipment.
UL 62368-1Audio/video, information and communication technology equipment—Part 1: Safety requirements.
UL 61010-2-030Safety requirements for electrical equipment for measurement, control, and laboratory use—Part 2-030: Particular requirements for testing and measuring circuits.
UL 61010B-2-031Electrical Equipment for Measurement, Control, and Laboratory Use; Part 2: Particular Requirements for Hand-Held Probe Assemblies for Electrical Measurement and Test.

OSHA's recognition of any NRTL for a particular test standard is limited to equipment or materials for which OSHA standards require third-party testing and certification before using them in the workplace. Consequently, if a test standard also covers any products for which OSHA does not require such testing and certification, an NRTL's scope of recognition does not include these products.

The American National Standards Institute (ANSI) may approve the test standards listed above as American National Standards. However, for convenience, we may use the designation of the standards-developing organization for the standard as opposed to the ANSI designation. Under the NRTL Program's policy (see OSHA Instruction CPL 1-0.3, Appendix C, paragraph XIV), any NRTL recognized for a particular test standard may use either the proprietary version of the test standard or the ANSI version of that standard. Contact ANSI to determine whether a test standard is currently ANSI-approved.

A. Conditions

In addition to those conditions already required by 29 CFR 1910.7, CSL must abide by the following conditions of the recognition:

1. CSL must inform OSHA as soon as possible, in writing, of any change of ownership, facilities, or key personnel, and of any major change in its operations as an NRTL, and provide details of the change(s);

2. CSL must meet all the terms of its recognition and comply with all OSHA policies pertaining to this recognition; and

3. CSL must continue to meet the requirements for recognition, including all previously published conditions on CSL's scope of recognition, in all areas for which it has recognition.

Pursuant to the authority in 29 CFR 1910.7, OSHA hereby expands the scope of recognition of CSL, subject to the limitation and conditions specified above.

III. Authority and Signature

David Michaels, Ph.D., MPH, Assistant Secretary of Labor for Occupational Safety and Health, 200 Constitution Avenue NW., Washington, DC 20210, authorized the preparation of this notice. Accordingly, the Agency is issuing this notice pursuant to 29 U.S.C. 657(g)(2), Secretary of Labor's Order No. 1-2012 (77 FR 3912, Jan. 25, 2012), and 29 CFR 1910.7.

Start Signature

Signed at Washington, DC, on August 5, 2015.

David Michaels,

Assistant Secretary of Labor for Occupational Safety and Health.

End Signature End Supplemental Information

[FR Doc. 2015-19594 Filed 8-7-15; 8:45 am]