This site displays a prototype of a “Web 2.0” version of the daily
Federal Register. It is not an official legal edition of the Federal
Register, and does not replace the official print version or the official
electronic version on GPO’s govinfo.gov.
The documents posted on this site are XML renditions of published Federal
Register documents. Each document posted on the site includes a link to the
corresponding official PDF file on govinfo.gov. This prototype edition of the
daily Federal Register on FederalRegister.gov will remain an unofficial
informational resource until the Administrative Committee of the Federal
Register (ACFR) issues a regulation granting it official legal status.
For complete information about, and access to, our official publications
and services, go to
About the Federal Register
on NARA's archives.gov.
The OFR/GPO partnership is committed to presenting accurate and reliable
regulatory information on FederalRegister.gov with the objective of
establishing the XML-based Federal Register as an ACFR-sanctioned
publication in the future. While every effort has been made to ensure that
the material on FederalRegister.gov is accurately displayed, consistent with
the official SGML-based PDF version on govinfo.gov, those relying on it for
legal research should verify their results against an official edition of
the Federal Register. Until the ACFR grants it official status, the XML
rendition of the daily Federal Register on FederalRegister.gov does not
provide legal notice to the public or judicial notice to the courts.
Rule
Enter a search term or FR citation e.g.
88 FR 38230 FR 78782024-13208USDA09/05/24RULE0503-AA39SORN
Choosing an item from
full text search results
will bring you to those results. Pressing enter in the search box
will also bring you to search results.
Choosing an item from
suggestions
will bring you directly to the content.
This table of contents is a navigational tool, processed from the
headings within the legal text of Federal Register documents.
This repetition of headings to form internal navigation links
has no substantive legal effect.
Document page views are updated periodically throughout the day and are
cumulative counts for this document. Counts are subject to sampling,
reprocessing and revision (up or down) throughout the day.
Page views
80
as of
11/17/2026 at 2:15 pm EST
Other Formats
Enhanced Content - Other Formats
This document is also available in the following formats:
This PDF is FR Doc. 2016-08961 as it appeared on Public Inspection on
04/29/2016 at 8:45 am.
If you are using public inspection listings for legal research, you
should verify the contents of the documents against a final, official
edition of the Federal Register. Only official editions of the
Federal Register provide legal notice of publication to the public and judicial notice
to the courts under 44 U.S.C. 1503 & 1507.
Learn more here.
Published Document: 2016-08961 (81 FR 26124)
This document has been published in the Federal Register. Use the PDF linked in the document sidebar for the official electronic format.
AGENCY:
Federal Aviation Administration (FAA), Department of Transportation (DOT).
ACTION:
Final rule.
SUMMARY:
We are revising Airworthiness Directive (AD) 2015-09-04 for DG Flugzeugbau GmbH Model DG-1000T gliders equipped with a Solo Kleinmotoren Model 2350 C engine. This AD results from mandatory continuing airworthiness information (MCAI) issued by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as engine shaft failure and consequent propeller detachment. We are issuing this AD to require actions to address the unsafe condition on these products.
DATES:
This AD is effective June 6, 2016.
The Director of the Federal Register approved the incorporation by reference of certain publications listed in the AD as of June 6, 2016.
The Director of the Federal Register approved the incorporation by reference of a certain other publication listed in this AD as of May 26, 2015 (80 FR 25591, May 5, 2015).
ADDRESSES:
You may examine the AD docket on the Internet at
http://www.regulations.gov
by searching for and locating Docket No. FAA-2015-1130; or in person at the Docket Management Facility, U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE., Washington, DC 20590.
For service information identified in this AD, contact Solo Kleinmotoren GmbH, Postfach 600152, 71050 Sindelfingen, Germany; telephone: +49 7031 301-0; fax: +49 7031 301-136; email:
aircraft@solo-germany.com;
Internet:
http://aircraft.solo-online.com
and DG Flugzeugbau GmbH, Otto Lilienthal Weg 2/Am Flugplatz, 76646 Bruchsal, Germany; telephone: +49 7251 3020-0; fax: +49 7251 3020-200; email:
wassenaar@dg-flugzeugbau.de;
Internet:
http://www.dg-flugzeugbau.de/
index.php?id=1329. You may view this
( printed page 26125)
referenced service information at the FAA, Small Airplane Directorate, 901 Locust, Kansas City, Missouri 64106. For information on the availability of this material at the FAA, call (816) 329-4148. It is also available on the Internet at
http://www.regulations.gov
by searching for Docket No. FAA-2015-1130.
FOR FURTHER INFORMATION CONTACT:
Jim Rutherford, Aerospace Engineer, FAA, Small Airplane Directorate, 901 Locust, Room 301, Kansas City, Missouri 64106; telephone: (816) 329-4165; fax: (816) 329-4090; email:
jim.rutherford@faa.gov.
SUPPLEMENTARY INFORMATION:
Discussion
We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR part 39 by adding an AD that would apply to DG Flugzeugbau GmbH Model DG-1000T gliders equipped with a Solo Kleinmotoren Model 2350 C engine. The NPRM was published in the
Federal Register
on February 4, 2016 (81 FR 5944), and proposed to revise AD 2015-09-04, Amendment 39-18150 (80 FR 25591, May 5, 2015).
Since we issued AD 2015-09-04, Amendment 39-18150 (80 FR 25591, May 5, 2015), new service information has been issued that includes procedures for replacement of the excenter axle-pulley assembly and installation of an elastomeric damper element between the propeller and upper pulley. This optional modification will allow resuming engine operation.
The European Aviation Safety Agency (EASA), which is the Technical Agent for the Member States of the European Community, has issued AD No.: 2015-0052R1, dated November 19, 2015 (referred to after this as “the MCAI”), to correct the above-referenced unsafe condition for the specified products. The MCAI states:
An occurrence of engine shaft failure and consequent propeller detachment was reported on a Solo 2350 C engine.
This condition, if not corrected, could lead to additional cases of release of the propeller from the engine, possibly resulting in damage to the sailplane, or injury to persons on the ground.
To address this unsafe condition, EASA issued Emergency AD 2013-0217-E to prohibit operation of the engine. That AD was later revised to introduce an optional modification, through Solo Kleinmotoren Service Bulletin (SB) 4603-14, to install a modified excenter axle-pulley assembly, allowing to resume operation of the engine.
Since EASA AD 2013-0217R1 was issued, another occurrence of engine shaft failure and propeller detachment was reported on a Solo 2350 C engine which had been modified in accordance with Solo Kleinmotoren SB 4603-14.
Consequently, EASA issued Emergency AD 2015-0052-E, which superseded AD 2013-0217R1, to prohibit operation of all Solo 2350 C engines, including those engines which had been modified in accordance with Solo Kleinmotoren SB 4603-14. That AD also required a one-time inspection of the propeller shaft to detect cracks and the reporting of findings.
Since that AD was issued, Solo Kleinmotoren GmbH developed modification drawing nb. 2031211-V2 available for in service application through Solo SB 4603-17 and DG Flugzeugbau GmbH developed modifications drawing nb. 10 M 067, available for in service application through DG Flugzeugbau Technical Note (TN) 1000/26 which include replacement of excenter axle-pulley assembly and installation of an elastomeric damper element between the propeller and upper pulley.
This AD is revised to introduce optional modifications to allow resuming operation of an engine.
We gave the public the opportunity to participate in developing this AD. We received no comments on the NPRM (81 FR 5944, February 4, 2016) or on the determination of the cost to the public.
Conclusion
We reviewed the relevant data and determined that air safety and the public interest require adopting the AD as proposed except for minor editorial changes. We have determined that these minor changes:
Are consistent with the intent that was proposed in the NPRM (81 FR 5944, February 4, 2016) for correcting the unsafe condition; and
Do not add any additional burden upon the public than was already proposed in the NPRM (81 FR 5944, February 4, 2016).
We reviewed Solo Kleinmotoren GmbH Anleitung zur Inspektion (English translation: Inspection Instruction), Nr. 4603-1, Ausgabe (English translation: Dated) March 26, 2015; Solo Kleinmotoren GmbH Technische Mitteilung (English translation: Service Bulletin) Nr. 4603-17, Ausgabe (English translation: Dated) July 15, 2015; and DG Flugzeugbau GmbH Technical note No. 1000/26, dated September 23, 2015, with 10M072 titled Propellermontage nach TM 1000-26 (English translation: Propeller assembly TN 1000-26), dated July 14, 2015. Solo Kleinmotoren GmbH Anleitung zur Inspektion (English translation: Inspection Instruction), Nr. 4603-1, Ausgabe (English translation: Dated) March 26, 2015, describes procedures for inspecting the propeller shaft for cracking and reporting the results to the manufacturer. Solo Kleinmotoren GmbH Techniseche Mitteilung (English translation: Service Bulletin) Nr. 4603-17, Ausgabe (English translation: Dated) July 15, 2015, describes procedures for replacement of the excenter axle-pulley assembly. DG Flugzeugbau GmbH Technical note No. 1000/26, dated September 23, 2015, describes procedures for removing the excenter axle-pulley assembly and sending it to Solo Kleinmotoren GmbH for modification with a new rear bearing, axle, and elastomeric damper element. This service information is reasonably available because the interested parties have access to it through their normal course of business or by the means identified in the
ADDRESSES
section.
Costs of Compliance
We estimate that this AD will affect 2 products of U.S. registry. We also estimate that it will take about .5 work-hour per product to comply with the basic operational limitation requirement of this AD. The average labor rate is $85 per work-hour.
Based on these figures, we estimate the cost of this portion of this AD on U.S. operators to be $85, or $42.50 per product.
We also estimate that it will take about 1.5 work-hours per product to comply with the basic axle inspection (remove, inspect, and reinstall) requirement of this AD. The average labor rate is $85 per work-hour.
Based on these figures, we estimate the cost of this portion of this AD on U.S. operators to be $255, or $127.50 per product.
We also estimate that it will take about 2 work-hours per product to comply with the optional axle with drive belt pulley unit replacement and engine test run of this AD. The average labor rate is $85 per work-hour. Required parts will cost about $100 per product.
Based on these figures, we estimate the cost of this optional AD action on U.S. operators to be $540, or $270 per product.
We also estimate that it will take about .5 work-hour per product to comply with the removal of the operational limitation requirement after doing the optional replacement of this
( printed page 26126)
AD. The average labor rate is $85 per work-hour.
Based on these figures, we estimate the cost of this AD action on U.S. operators to be $85, or $42.50 per product.
Paperwork Reduction Act
A federal agency may not conduct or sponsor, and a person is not required to respond to, nor shall a person be subject to penalty for failure to comply with a collection of information subject to the requirements of the Paperwork Reduction Act unless that collection of information displays a current valid OMB control number. The control number for the collection of information required by this AD is 2120-0056. The paperwork cost associated with this AD has been detailed in the Costs of Compliance section of this document and includes time for reviewing instructions, as well as completing and reviewing the collection of information. Therefore, all reporting associated with this AD is mandatory. Comments concerning the accuracy of this burden and suggestions for reducing the burden should be directed to the FAA at 800 Independence Ave. SW., Washington, DC 20591. ATTN: Information Collection Clearance Officer, AES-200.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. “Subtitle VII: Aviation Programs,” describes in more detail the scope of the Agency's authority.
We are issuing this rulemaking under the authority described in “Subtitle VII, Part A, Subpart III, section 44701: General requirements.” Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.
Regulatory Findings
We determined that this AD will not have federalism implications under Executive Order 13132. This AD will not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government.
For the reasons discussed above, I certify this AD:
(2) Is not a “significant rule” under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979),
(3) Will not affect intrastate aviation in Alaska, and
(4) Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.
Examining the AD Docket
You may examine the AD docket on the Internet at
http://www.regulations.gov
by searching for and locating Docket No. FAA-2015-1130; or in person at the Docket Management Facility between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains the NPRM, the regulatory evaluation, any comments received, and other information. The street address for the Docket Office (telephone (800) 647-5527) is in the
ADDRESSES
section. Comments will be available in the AD docket shortly after receipt.
This airworthiness directive (AD) becomes effective June 6, 2016.
(b) Affected ADs
This AD replaces AD 2015-09-04, Amendment 39-18150 (80 FR 25591, May 5, 2015) (“AD 2015-09-04”).
(c) Applicability
This AD applies to DG Flugzeugbau GmbH Model DG-1000T gliders, all serial numbers, that are:
(1) Equipped with a Solo Kleinmotoren Model 2350 C engine; and
(2) Certificated in any category.
(d) Subject
Air Transport Association of America (ATA) Code 72: Engine.
(e) Reason
This AD was prompted by mandatory continuing airworthiness information (MCAI) issued by the aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as engine shaft failure with consequent propeller detachment. We are issuing this AD to prevent failure of the engine shaft with consequent propeller detachment, which could result in damage to the glider or injury of persons on the ground.
(f) Actions and Compliance
Unless already done, do the following actions:
(1) As of November 25, 2013 (the effective date retained from AD 2013-22-14, Amendment 39-17646 (78 FR 65869, November 4, 2013)), do not operate the engine unless the engine is modified following instructions that are FAA-approved specifically for this AD.
(2) Modification of an engine following the instructions in Solo Kleinmotoren Service Bulletin 4603-14, dated April 28, 2014, is not an acceptable modification to comply with paragraph (f)(1) of this AD.
(3) As of May 26, 2015 (the effective date retained from AD 2015-09-04), place a copy of this AD into the Limitations section of the aircraft flight manual (AFM).
(4) Within the next 30 days after May 26, 2015 (the effective date retained from AD 2015-09-04), do a one-time inspection (magnetic particle or dye penetrant) of the propeller shaft following Solo Kleinmotoren GmbH Anleitung zur Inspektion (English translation: Inspection Instruction), Nr. 4603-1, Ausgabe (English translation: dated) March 26, 2015.
Note 1 to paragraph (f)(4) of this AD:
This service information contains German to English translation. The EASA used the English translation in referencing the document. For enforceability purposes, we will refer to the Solo Kleinmotoren service information as it appears on the document.
(5) Within the next 30 days after May 26, 2015 (the effective date retained from AD 2015-09-04), report the results of the inspection required in paragraph (f)(4) of this AD to Solo Kleinmotoren GmbH. Include the serial number of the engine and the operational time since change of the axle in your report. You may find contact information for Solo Kleinmotoren GmbH in paragraph (i)(5) of this AD.
(6) At any time after June 6, 2016 (the effective date of this AD), you may modify the engine following Solo Kleinmotoren GmbH Techniseche Mitteilung (English translation: Service Bulletin) Nr. 4603-17,
( printed page 26127)
Ausgabe (English translation: Dated) July 15, 2015; and DG Flugzeugbau GmbH Technical note No. 1000/26, dated September 23, 2015, with 10M072 titled Propellermontage nach TM 1000-26 (English translation: Propeller assembly TN 1000-26), dated July 14, 2015. This modification allows engine operation.
Note 2 to paragraph (f)(6) of this AD:
This service information contains German to English translation. The EASA used the English translation in referencing the document. For enforceability purposes, we will refer to the Solo Kleinmotoren service information and the DG Flugzeugbau GmbH as it appears on the document.
(7) Before further flight after doing the modification allowed in (f)(6) of this AD, remove the AD placed into the Limitations section of the AFM as required in paragraph (f)(3) of this AD.
(g) Other FAA AD Provisions
The following provisions also apply to this AD:
(1)
Alternative Methods of Compliance (AMOCs):
The Manager, Standards Office, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. Send information to ATTN: Jim Rutherford, Aerospace Engineer, Small Airplane Directorate, 901 Locust, Room 301, Kansas City, Missouri 64106; telephone: (816) 329-4165; fax: (816) 329-4090; email:
jim.rutherford@faa.gov.
Before using any approved AMOC on any airplane to which the AMOC applies, notify your appropriate principal inspector (PI) in the FAA Flight Standards District Office (FSDO), or lacking a PI, your local FSDO.
(2)
Airworthy Product:
For any requirement in this AD to obtain corrective actions from a manufacturer or other source, use these actions if they are FAA-approved. Corrective actions are considered FAA-approved if they are approved by the State of Design Authority (or their delegated agent). You are required to assure the product is airworthy before it is returned to service.
(3)
Reporting Requirements:
For any reporting requirement in this AD, a federal agency may not conduct or sponsor, and a person is not required to respond to, nor shall a person be subject to a penalty for failure to comply with a collection of information subject to the requirements of the Paperwork Reduction Act unless that collection of information displays a current valid OMB Control Number. The OMB Control Number for this information collection is 2120-0056. Public reporting for this collection of information is estimated to be approximately 5 minutes per response, including the time for reviewing instructions, completing and reviewing the collection of information. All responses to this collection of information are mandatory. Comments concerning the accuracy of this burden and suggestions for reducing the burden should be directed to the FAA at: 800 Independence Ave. SW., Washington, DC 20591, Attn: Information Collection Clearance Officer, AES-200.
(1) The Director of the Federal Register approved the incorporation by reference (IBR) of the service information listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
(2) You must use this service information as applicable to do the actions required by this AD, unless the AD specifies otherwise.
(3) The following service information was approved for IBR on June 6, 2016.
(i) Solo Kleinmotoren GmbH Techniseche Mitteilung (English translation: Service Bulletin) Nr. 4603-17, Ausgabe (English translation: Dated) July 15, 2015.
Note 3 to paragraphs (i)(3)(i) and (i)(3)(ii) of this AD:
This service information contains German to English translation. The EASA used the English translation in referencing the document. For enforceability purposes, we will refer to the Solo Kleinmotoren service information and the DG Flugzeugbau GmbH as it appears on the document.
(ii) DG Flugzeugbau GmbH Technical note No. 1000/26, dated September 23, 2015, with 10M072 titled Propellermontage nach TM 1000-26 (English translation: Propeller assembly TN 1000-26), dated July 14, 2015.
(4) The following service information was approved for IBR on May 26, 2015 (80 FR 25591, May 5, 2015).
(i) Solo Kleinmotoren GmbH Anleitung zur Inspektion (English translation: Inspection Instruction), Nr. 4603-1, Ausgabe (English translation: Dated) March 26, 2015.
Note 4 to paragraph (i)(4)(i) of this AD:
This service information contains German to English translation. The EASA used the English translation in referencing the document. For enforceability purposes, we will refer to the Solo Kleinmotoren service information as it appears on the document.
(ii) Reserved.
(5) For service information identified in this AD, contact Solo Kleinmotoren GmbH, Postfach 600152, 71050 Sindelfingen, Germany; telephone: +49 7031 301-0; fax: +49 7031 301-136; email:
aircraft@solo-germany.com;
Internet:
http://aircraft.solo-online.com/com.
(6) You may view this service information at FAA, Small Airplane Directorate, 901 Locust, Kansas City, Missouri 64106. For information on the availability of this material at the FAA, call (816) 329-4148. In addition, you can access this service information on the Internet at
http://www.regulations.gov
by searching for and locating Docket No. FAA-2015-1130.
(7) You may view this service information that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202-741-6030, or go to:
http://www.archives.gov/federal-register/cfr/ibr-locations.html.
Issued in Kansas City, Missouri, on April 11, 2016.
Melvin Johnson,
Acting Manager, Small Airplane Directorate, Aircraft Certification Service.